3 graphs on ONE paper

I have made an LV in labview6.0. It is used to show three types of graph in one place. It is attached. They are (i) Force Vs velocity (ii) Force Vs Distance and (iii) No. of rotations vs distance. Is it possible to show only ONE type at a time without too much adjustments everytime?
Attachments:
forum RTF.rtf ‏218 KB

Hi everyone!
Using an enum with a Case Structure is a great option that will allow you to accomplish what you're trying to do. Just to round out the discussion here, though, let's talk about some Express technology that could make this task even easier. Express technology was first introduced in LabVIEW 7, and it has been greatly extended in versions 7.1 and 8.
Express technology is a set of VI's that use configuration-based dialogs to actually implement the code for the selections you make in the dialog. LabVIEW actually does the coding for you!
Consider the following example, which uses the Prompt User for Input Express VI to pop up a dialog asking the user to place checkmarks in the checkboxes for the signals to be graphed. Then 3 signals are simulated and only the selected signals are graphed by using the Select Signals Express VI. The code itself is very easy, since LabVIEW implements the decision making code for you.
LabVIEW 7 and above also contain other features which will make your programming experience easier, such as an increased number of examples and documentation, simplified wiring techniques, and more.
I'll attach a screenshot of the code for those of you who don't have LabVIEW 7.1 or above.
Jarrod S.
National Instruments
Attachments:
Signal Selector.vi ‏443 KB
Express Solution.JPG ‏74 KB

Similar Messages

Several pages only on one paper

Hi expert
In the print preview, there are several pages displayed, but when I try to print on the paper, all the pages are printed only on one paper and it leads to overlap. It looks ugly. Anyone can help me with that, thank you very much. By the way I use smartform.
Alex

If your problem was with Adobe forms, i would recommend you to check the subforms content to be flowed. But this is not likely in this forum, right? Good luck ,Otto

Plotting multiple graphs on one waveform chart with dynamic data types

I'm trying to put multiple graphs on one waveform chart and having data agreement errors. I'm wondering if it has anything to do with the fact that dynamic data is being used (I've had no problems with other datatypes in the past). Does anyone know how to correct this problem? I've attached the following .VI. There will be plenty of .VIs on the bottom that won't load, but they are not consequential for this problem.
Thanks!
Brian
Solved!
Go to Solution.
Attachments:
Stiffness Control V1.vi ‏119 KB

you could use stacked plots by right clicking on the chart and clicking on the stacked plots and than on the front panek you can put a bundle function on the FP and hook your signals up
Harold Timmis
[email protected]
Orlando,Fl
*Kudos always welcome
Attachments:
multiplotwaveform.JPG ‏138 KB

Print multiples of the same image on one paper. I tried to change the layout to 9 per page, but it's only showing up and printing one per page, though it is the size i would like. But only one image is showing up as opposed to 9

I'm trying to print multiples of the same image on one paper. I tried to change the layout to 9 per page, but it's only showing up and printing one per page, though it is the size i would like. But only one image is showing up as opposed to 9. HELP!!Version 7.0 (826.4)
I'm using Preview Version 7

Hello @kgingeri1,
Welcome to the HP forums.
If you have sent a test print via ePrint, and experience this issue, i would call the Cloud Services department.
If ePrint works fine, it is definitely a Google Cloud Print issue.
Also, when you print from your android device, are you using Google Cloud print or the HP ePrint app?
Please call our Cloud Services at 855-785-2777.
If you live outside the US/Canada Region, please click the link below to get the support number for your region. http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
Hours:
Mon-Fri. 8am - 11pm, Sat. 9am-8pm - EST
Mon-Fri. 7am - 10pm, Sat. 8am-7pm - CST
Mon-Fri. 6am - 9pm, Sat. 7am-6pm - MST
Mon-Fri. 5am - 8pm, Sat. 6am-5pm - PST
Aardvark1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!

Add multiple graphs in one chart(ex.scatter chart) using labview excel report generation toolkit

How to add multiple graphs in one chart(ex.scatter chart) using labview excel report generation toolkit. Assume like my test data is like below:
X-Axis
Data1
Data2
1
1
2
13
2
3
14
3
4
15
5
5
16
3
6
7
7
The above graph generated manually in excel. I want to generate the same using excel report generation toolkit. when I use Excel Insert Graph.vi where the input data is 2D array with numeric data but here labview converts the empty cells (eg.x -axis 1,data1- is empty) as zero and while plotting i am getting zero for empty cell values.
Can anyone please help me on how to plot the graph without adding zero for empty cells?
Thanks&Regards,
Bharathi T
TE
X-Axis
Data1
Data2
1
1
2
13
2
3
14
3
4
15
5
5
16
3
6
7
7

Hi Bharathi,
The Excel Insert graph function takes in only 2d arrays as inputs. Since arrays can only have numeric values, any table with a null string is read as 0. Now to get a plot like you mentioned, you could read the table and replace blank Strings as NaN. NaN values in an array when plotted do not appear in the excel sheet. For reference I have attached a sample vi to help you understand.
Regards
Vijetha Nuthakki,
Applications Engineer
NI Systems India
Attachments:
Excel_graph_multiplot.vi ‏21 KB

I'm using printer laserjet p2055 ,i have 2 pages i want print them on one paper but both faces

i want print 2 pages of text on one paper ,its mean print first page on front paper and second page on back of the paper,,please how can i do that,,thanks

rega83 wrote:
thank you very much,,but what u mean in dn model?
Hi,
Have you read the above link ? P2055 is a series of few models, dn is the way HP named it, could be duplex, network - I don't know. The d could be only duplex.
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Saved PDF graphs on one page?

When I save my survey results graph as a PDF, it is very large and separted by multiple pages. Is there a way to reduce this size to just 1 page without having to bring it into Photoshop to reduce the size to fit on a 1 page PDF?
Thanks,
Greg

I took a look at the form you shared and the Summary Report. I created a copy of your form to experiment with and did not change anything in your form.
In order to have the entire Summary Report tile appear on a single page in PDF you can do a few things:
1) You can remove the caption from displaying in the first field, from the little settings gear on the top right corner of the report tile un-select "Caption", since you don't have one on this field and it takes up a small amount of vertical space.
2) You can change the font size used in the Summary Report tiles, there is a "T" in the toolbar that exposes the text tools, I tried a 9pt font
3) Go to "File" - "Page Setup" when you are on the Summary Report tab and you can define the size and orientation of the PDF page, I changed it to have a Paper width of 11" and a Paper height of 13" and everything fits on one page.
I hope that these tweaks satisfy your needs...
Thanks,
Josh

HP officejet j4680 all-in-one paper jam issue

I bought HP officejet j4680 all-in-one two months ago from a dealer. Now it keeps telling me a "paper jam" which doesn't exist. I tried everything from the troubleshooting in HP website. The jam light just keeps blinking. Now I am so frustrated with this product.

@CAGY, take a look at this HP link on how to clear a jam.
Please mark the post that solves your issue as "Accept as Solution".
If my answer was helpful click the “Thumbs Up" on the left to say “Thanks”!
I am not a HP employee.

HP Officejet 5610 All-in-one paper jam problem

Please is anyone out who can heIp me.
I tried to print a word document from my computer and my printer came up with the following message: Paper jam: clear jam and press ok. I have looked through the printer to see if there is any paper jammed in the printer. I just couldn't find any. This is the first time I have experienced this paper jam problem with my printer.
On pressing the OK button resulted in the printer making some strange noise (sounding as if it is trying to pickup a paper) with the catridge mechanism sliding from one side to the other for about 10 seconds without a paper in the paper tray being picked up. It then shows the paper jam message again and again. It has been the same for the last 5 hours and I need to print some documents urgently.
I have tried all of the following troubleshooting I found on the HP website without any joy.
Step one: Remove any loose paper Remove any loose paper from the input tray.
Step two: Clear the jam from the back of the Allin-
One 1. On the rear of the product, press in the tab on the left side of the rear access
door to release the door. Pull the door away from the product to remove it. Gently pull the
paper out of the rollers. CAUTION: If the paper tears while being removed from the
rollers, check the rollers and wheels for torn pieces of paper that might have remained
inside the product. Loose pieces of paper will cause future paper jams. Replace the
rear access door. Gently push the door forward until it snaps into place. Press OK to
continue the current print job. If the issue is not resolved , continue to the next step. If
the issue is resolved , you do not need to continue to the next step. If these steps
resolved the issue , there is no need to continue troubleshooting. If the issue persists , see the next step.
Step three: Clean the rollers Turn off the unit, and then unplug the power cord. Press in the tab on
the left side of the rear clean-out door to release the door. Remove the door by
pulling it away from the unit. Wipe the paper rollers with a lint-free cloth lightly moistened
with distilled or bottled water. Rotate the rollers with your fingers to clean all the way
around. Allow the rollers to dry completely, and then replace the rear access door. Plug
the unit back in and turn it on. If these steps resolved the issue , there is no need to
continue troubleshooting. If the issue persists , see the next step.
Step four: Clear the jam from the automatic document feeder (ADF) Lift the cover of the ADF.
Lifting the ADF cover Gently pull the paper out of the rollers. CAUTION: If the paper
tears when being removed from the rollers, check the rollers and wheels for torn pieces
of paper that might be remaining inside the product. Loose pieces of paper will cause
future paper jams. Close the cover of the ADF. If these steps resolved the issue ,
there is no need to continue troubleshooting. If the issue persists , see the next step. The
next step couldn't be done because the paper is not loading.

@CAGY, take a look at this HP link on how to clear a jam.
Please mark the post that solves your issue as "Accept as Solution".
If my answer was helpful click the “Thumbs Up" on the left to say “Thanks”!
I am not a HP employee.

Multi Plot XY Graph. One Plot Envlope, checking to make sure the other plot falls within the enclope plot

Hi Guys
Have a problem with XY graphing, I have 5 xy samples that define an envlope (one plot), samples need to be checked to make sure they are within the selected envlope.
Any Ideas ?

Can you split the 4 xy point for your envelope int two envelopes:
Upper Limit 0,0 3,6 9,9
Lower Limit 3,0 9,9 (or maybe 0,0 3,0 9,9 if you need to start at x=0)
Then in your limit check connect both upper and lower envelopes.
Have a look at the attached vi, it's not very tidy and there may be a problem with the number of samples in the various arrays, it may give you some ideas to try.
Attachments:
Check_Envelope.vi ‏72 KB

HP OfficeJet All-in-One Paper Jam

I have been given to troubleshoot an OfficeJet 6210 All-in-One Printer/copier/fax machine. It suffered a paper jam for its troubles. I had cleared the jam from the machine and checked everywere else I could check freely without cracking it open. I restarted it and it gave me the same error. I finally had it do a partial reset to try and fix it. What it gave me was the same error message. Short of opening it up with a screwdriver and patience, what could potentially still keep giving me the error message after all steps have been taken to clear it and it failed?
Daniel Ray Seelye

@CAGY, take a look at this HP link on how to clear a jam.
Please mark the post that solves your issue as "Accept as Solution".
If my answer was helpful click the “Thumbs Up" on the left to say “Thanks”!
I am not a HP employee.

Hp 1350 all in one "paper jam" message

I have a HP 1350 All In One Printer and I can print a test sheet but I can't print, I get a "paper jam" message. Help

Hard Reset – While printer is powered ON, pull
the power cord from the printer then from the
wall. After 30 seconds reconnect power to
wall and printer. This will trigger a ‘dirty power
up’ and restore the printer to a known good
condition (if it is possible). No user settings
are lost with a ‘hard reset’.
This ‘Hard Reset’ is one of the most powerful
tools to use when the printer hardware is not
functioning properly!
Although I am working on behalf of HP, I am speaking for myself and not for HP.
Love Kudos! If you feel my post has helped you please click the White Kudos! Star just below my name : )
If you feel my answer has fixed your problem please click 'Mark As Solution' and make it easier for others to find help quickly : )
Happy Troubleshooting : )

RE: HP 6110 all-in-one paper mismatch

My 6110 HP all-in -one won't do anything but tell me that it 'needs an alignment' press 'enter'. When I press "enter' a sheet of blank paper comes out right away and the display says,"paper Mismatch". I have tried all the paper sizes listed, to no avail. I can't get the printer to do anything else. I tried reinstalling the driver disk. too, but no use. Can anyone help me with this problem??

Hello CrossBear,
Welcome to the HP Support Forums.
Regarding the HP Officejet 6110 inquires you have about the USB cable and software, I would like to help. The USB cable needs to be USB 2.0 A-B, they are not product specific.
HP Officejet 6110 All-in-One Printer Drivers is where you can download the software and drivers for your Operating System if available. This printer does not have full feature software for Windows Vista, 7 and 8 for example.
Let me know if this has helped.
Thanks,
JERENDS
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

HP PSC 2355 all-in-one Paper Jam Error

Hi. I have an HP PSC 2355 all-in-one printer that has worked well for a long time but when i switched it on today to do some printing, it made some strange noises and when i tried to print it sent an error saying there was a paper jam - but there was not !
It feeds a sheet of paper in about half way through then stops and the error is displayed.
I tried doing a copy, and the exact same thing happens.
Has anyone got an idea what has gone wrong ?
Thanks.

Make sure to follow all steps here:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00212225&cc=au&dlc=en&lc=en&product=422000&tmp_...
Although I am working on behalf of HP, I am speaking for myself and not for HP.
Love Kudos! If you feel my post has helped you please click the White Kudos! Star just below my name : )
If you feel my answer has fixed your problem please click 'Mark As Solution' and make it easier for others to find help quickly : )
Happy Troubleshooting : )

Two XY graphs to one jpg

I currently save XY graphs to JPG files, but I am looking for a way to take two XY graphs and marry them to the same JPG file.
I am using LV 6.1 and WIN 2000.

> I currently save XY graphs to JPG files, but I am looking for a way to
> take two XY graphs and marry them to the same JPG file.
> I am using LV 6.1 and WIN 2000.
Hello
look at palette Functions>>Graphics&Sound>>Picture Plots
There is Plot XY.vi with top left point(0,0) input and picture output
If you use this vi twice and set properlly top left point(0,0) inputs, you
could see two plot on one picture indicator.
Next:
Functions>>Graphics&Sound>>Picture Functions Picture to Pixmap.vi and
Functions>>Graphics&Sound>>Graphics Foprmat and use Write JPEG File.vi
I stronglu sugest look more picture functions at Functions>>Graphics&Sound
Palette
regards
Mikrobi

3 graphs on ONE paper

Similar Messages

Maybe you are looking for