7304 nse100 FE Management Port configuration question

How can the F0/0 FE Management Port be used? Since the 7304 has a redundant NSE100 prossesor card I would like to use this port two ways as a remote router access port for management and as a standard FastEthernet interface. Is configuration and advertising of the interface IP address the same as standard FastEthernet interfaces?

The FastEthernet port on the Cisco 7304 is for management purposes only. Any other use of the FastEthernet port is not supported. This statement is according to the configuration notes of 7304.So, it cannot be used as a standard GE port.

Similar Messages

Half duplex or full duplex configuration for MDS9124 management port?

Hi All,
Is it possible to set the management port of mds 9124 about half or full duplex configuration?
I want to correct following error:
Jun 13 10:27:20.799 GMT: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on GigabitEthernet4/18 (not half duplex), with mtw1pc02bs0(FOX1450G8QG) mgmt0 (half duplex).
it seems mds 9124 set his port to half duplex.
Dennis

You may want to check this thread :
https://supportforums.cisco.com/thread/2059109
Else try the following :
switch# config terminal
switch(config)#
switch(config)# interface mgmt0
switch(config-if)# switchport duplex full
switch(config)# exit
switch#
switch# copy running-config startup-config
Also, I would suggest you check what the counterpart of your MDS switch mgmt interface is set to (i.e. is it set to autoneg, then try setting it to fix speed/duplex or the other way around).

Question of telnet or SSH to 4500X management port

I configured 4500X management port (Fa1) and I can ping the IP from the network. But when I tried telnet to the port, the switch showed "password required but not set".
I didn't configure any password for VTY. Should it be equivalent to "no login"? If to set or change a password for the management port, where to configure it?
Thanks a lot

Hi,
Yes, "password" and "login" for the management port should be configured under the "vty" lines.
Best regards,
Antonin

Question about 4500X VSS management port

I have two standalone 4500X switches that I'm planning to convert to VSS. If I cable the management port on both switches to a management cloud, which management port should I put the management IP address? Is it the port on the active switch? if the active switch failed, would the management port on the standby switch take over the management IP?
The management port is in VRF mgmtVrf. Should I create a default route for the VRF such as "ip route vrf mgmtvrf 0.0.0.0 0.0.0.0 ....." to point to its default gateway IP?
Thanks

When you convert the chassis to VSS, only the management interfaces (FastEthernet1) for switch-1 (active) will be visible in the config. So you want to cable both management interfaces to your management cloud, but you only apply the IP to the active switch.
The management port is in VRF mgmtVrf. Should I create a default route for the VRF such as "ip route vrf mgmtvrf 0.0.0.0 0.0.0.0 ....." to point to its default gateway IP?
Correct, you need a default route in that mgmt vrf pointing to the gateway.
HTH

Management port on fabric interconnect question

I'm using the same pool of of IP addresses for my FI and KVM pool.
I need to make sure that my management port on each FI is connected to a switch that is also accessible in the same range\subnet, correct?
After setting everything up, I'm currently unable to get to my VIP.

Correct. Ensure the subnet masks are correct, and the gateway is reachable. If you can "ping" from outside to each FI's management IP, there's no reason you shouldn't be able to reach the VIP. Obivously the VIP address must be in the same subnet & VLAN as the management IPs, and not be used elsewhere in your environment.
Regards,
Robert

I can not make a "Automated Installation of the Introscope Agent" (Managed System Configuration, p.7)

I can not make a "Byte Code Adapter Installation"
When I open meets both paragraphs in step Managed System Configuration is somewhat obscure situations that do not allow the automatic configuration Introscope agent and Introscope Manager
Please help to resolve a number of questions that might help me complete the setup :
1. Why has the status of Enterprise Manager : <No Enterprise Manager configured> ( see picture)
I set up Enterprise Manager in accordance with the installation instructions and complied with all the setting items . Since without any configuration can be associated with the appearance of this status ?
2 . Why Server Node is empty detail settings ?
JDK Location:
Enterprise Manager Host:
Enterprise Manager Port:
Introscope Agent Name:
Introscope Agent Profile:
Autoprobe Directives:
Wily Version:
Introscope Agent Version:
Introscope Agent Log Location:
3 . What a mistake ($ MC: DIAG_WILY_MSG: 032 : L), which appears when I click configuration "Configure Introscope Agent Setup ...", and what it can be linked ? ( see picture )
And the last question , which is also linked to the process of automatic configuration and refers to a phrase from the instruction (Introscope Version 9
Installation Guide For SAP July 2012) points out "Automated Installation of the Introscope Agent via SMD"
there is such an item:
2 . Deploy ISAGENTJ5 *. SCA which is the Introscope Java Agent 9 with SDM to Solution Manager. You may need to deploy also ISAGENT *. SCA which is Introscope Java Agent 8.
However, nowhere does it say where exactly ( on what the absolute path ) I must perform unloading and then what to do with this discharge

The problem was resolved a small manipulation - on stage Basic Configuration,
point 3 "Configure CA Introscope"
I forgot to add to the list of CA Introscope Enterprise Managers link to my manager.
Thus it is necessary to take into account that the path should be correct (usually for linux - /usr/sap/ccms/apmintroscope) and the directory should be applied appropriate privileges.
Then in paragraph "Byte Code Adapter Installation" - there are all the necessary data, and it starts to work correctly

Management port on CSS 11150

I have a simple question. Can someone tell me how to access the management port on the css 11150?
I configured the ip and mask on the management port and condigured my laptop for a ip on the same network. But i am unable to connect.

what do you mean by connect ?
Are you trying telnet or HTTP ?
Are you able to ping ?
Is the interface showing up ?
Try 10Mb Half duplex set manually and see if it works.
Also, did you reboot the CSS after configuring the ip address/mask for the management interface ?
Gilles.

Wlc management port can't trunk other than native vlan

Hello,
Ihave installed my first WLC 5508 with this topology :
WLC Connected trought distrubtion SFP 1Gb port to Core Switch port configured as Trunk port permetting 3 Wireless VLAN :
- Management WLC, Wireless Voice and Wireless Data Vlan (native Vlan is management WLAN).
- I have created 2 dynamic interface on WLC regarding my Wireless VLAN :
10.7.1.0/24 : Defaut Management Virtual Interface when installing WLC +
10.7.6.0/24 : Voice Virtual Interface and
10.7.2.0/24 : Wireless Data Virtual Interface trought GUI.
DHCP configured on each dynamic interface is the L3 vlan interface for equal VLAN subent for CORE SWITCH contining IP DHCP Pool.
WLC Management Inerface IP adress is : 10.7.1.10/24
I Have create 2 WLAN with SSID named Data ID 1 & Voice ID2.
I have create and AP Groupe named APGRP1 containing the AP registered on WLC and using both SSID WLAN.
Both AP are connected to Switch acess port configured as access port to native management WLC VLAN.
I have create 3 IP DHCP pool on Core switch with related L3 Interfaces for Inter VLAN routing.
Problem: when I try to connect from laptop to Data SSID I get IP Address from management WLC VLAN a non DATA VLAN.
the same case from Wireless IP Phone configured with Voice SSID.
What can I modifie that permet to both device to get IP address from the correct VLAN?
Thnks

Hi Adil,
Q1 >> AP access port on the switch must be configured on an Access port mode or trunk mode?
ANS - The LWAPP/ CAPWAP APs connected to the switchport should be a Access port not trunk.
Q2>> if the first case, setting the port on, the same VLAN like WLC Management VLAN will support other WLAN Vlans (voice and data)?
ANS - Yes it does support, since the traffic which involes the WLAN will be inside the LWAPP/CAPWAP logical tunnel.
Q3>> I will verify the interface mapping between WLAN and Dynamic Interfaces and i will tell you.
ANS - I will be waiting for your response!!
lemme know if this answered your question..
Regards
Surendra
====
Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull

Duplicating AirPort Network Port Configuration/IP Aliasing with AirPort

I'm attempting to set up my Apache server to serve test websites with my network (I'll be serving by IP, and firewalled from the wide world of the web (namely, my eyes only websites (so they can be tested on windows browsers (alas, the majority of my viewership)))). Im fairly confident I can set up the Virtual Hosts (watch this space, that my be my next problem). However, I'd like to set up my computer to have more than one IP address. Im running Panther (10.3.9). Im connected wirelessly to my network. I have tried the recommended: go to 'Network Port Configurations' and click 'Duplicate'. However, the Duplicate button is inactive for my AirPort card. How can I duplicate it so I can IP Alias my mac?

I don't mean to question your decision, but why do you need to have more then one IP address?
With virtual hosts, you can redirect to a countless number folders (virtual sites) with your computer only having one IP address.
<VirtualHost *:80>
ServerName site1.yourwebsite.net
DocumentRoot /Library/WebServer/Documents/sites/site1.yourwebsite.net
</VirtualHost>
<VirtualHost *:80>
ServerName site2.yourwebsite.net
DocumentRoot /Library/WebServer/Documents/sites/site2.yourwebsite.net
</VirtualHost>
Of course you should use be using a dynamic DNS service. I use http://dyndns.org. They offer free service and also a great custom DNS service.
For testing purposes you can change you local hosts settings via Netinfo Manager. For example you can set site1.local and site2.local to point to 127.0.0.1 and then your site will be private and work like you had hundreds of IP addresses.

Understanding and using Logical Components for Managed System configuration

Experts.....
I am embarking on a fresh installation of SolMan 7 EhP1 SPS25 and after a few bugs along the way, I am finally nearing the end of including the first Managed System. Somewhat related to {forum:id=10293771] I am hoping I can get some advice, but specifically with regards to Logical Components.
General question - I have a slide from SAP that shows a picture from Product->System->Instance->Logical System (client)->Logical Component. I am confused because it shows that Client 100 of a given ABAP system could be assigned to Logical Component A, whereas Client 200 of the same system could be assigned to Logical Component B. This seems wrong to me?
I am at the last step of the managed systems configuration wizard : "create logical components" and only want to ensure that I set things up to hopefully ensure that later usages (Maintenance Optimizer, etc) will handle things correctly!!!
- Our SAP landscape is not very complex
1. only ERP and EP (Dev/Test/Prod).
2. We are utilizing HR Self Service (XSS).
3. The ERP ABAP systems are on Netweaver 7.01.
4. EhP4 has been installed, however we only activated the HCM business functions. Therefore SAP_HR is on 604 whereas SAP_APPL is on 600. I think this might be driving some of the confusion in SMSY
For the DEV ABAP system I am trying to configure:
1. The system is showing up in two products : "SAP ERP" and "SAP ERP Enhancement Package" with the header data for both showing "EHP4 FOR SAP ERP 6.0 / NW7.01" and "SAP ERP 6.0"
2. Under "SAP ERP" the "product instance selection" shows only "SAP NW - Adobe Docu. Service" and "SAP ECC Server" as relevant
3. Under ""SAP ERP Enhancement Package" the "product instance selection" shows only "Human Capital Mgmt" as relevant by default. I manually flagged the development portal system as "relevant" for "SAP XSS (Self Services)"
4. The RCA DBA Cockpit system is complaining "No data available for extractor activation. Please check product mapping and Software Components in SMSY"
5. In the Managed System wizard, there is no logical component for any of the "EHP4 FOR SAP ERP 6.0 / NW7.01" selections
From what I can tell, I think this is correct:
1. Create a Z_EHP4 logical component and assign the DEV/QAS/PRD systems to them
2. Also assign the DEV/QAS/PRD to the existing SAP logical component "SAP ERP ECC SERVER"???
3. For the Solutions, my plan is to create
a. Non-Production ERP : with the dev/test erp/ep systems, but test system as the leading system
b. Production ERP with the prod erp/ep systems only
Thanks for any advice/guidance to help me avoid future problems!!
Edited by: Eric Poellinger on Jun 15, 2011 6:32 PM

General question - I have a slide from SAP that shows a picture from Product->System->Instance->Logical System (client)->Logical Component. I am confused because it shows that Client 100 of a given ABAP system could be assigned to Logical Component A, whereas Client 200 of the same system could be assigned to Logical Component B. This seems wrong to me?
Client 100 could be assigned to any number of logical components, client 200 could be assigned to those same ones or none of them. A logical component is just a grouping of systems used to accomplish some task in SolMan.
For example with ChaRM you could have 2 logical components.
ZCHARM_DEV development (100) -> QA (200) -> prod (300)
ZCHARM_SEC security (900) -> QA (200) -> prod(300)
One is used to show the path for moving development changes to prod, the other for security changes. 200 belongs to both, but 100 only to one.
Set them up in whatever way meets you needs. It looks like for you, you could just use the default one and assign your clients to the various system roles. Not all functionality in SolMan uses the logical components though.

Link SAP PI 7.3 to SolMan 7.1 - error during managed system configuration

All,
I installed my diagnostics agent twice with different options:
- Direct P4 connection via Java EE Dispatcher Node with port 5xx04
- P4 connection via SCS message server with port 81xx
In both cases I get an error during the managed system configuration of SAP PI 7.3: Remote error : Connection to P4 port of managed system failed.
I'm a bit confused with the step Enter System Parameters. In the Java parameters section, I can only enter port 39xx. if not, I get an error.
Also, I marked and unmarked the option concerning the ABAP user store, but the error persists.
Please advice.
Thanks a lot.

Hi Allam,
I checked the KBA and I think now, I have the correct HTTP port.
The error I now get is S:CL_DIAGSTP_MESSAGE:483
When I take the next step, Configure Automatically, I get this error during the Byte Code Adapter Installation phase when I open the Java URL stated in the navigation column:
DIAG_WILY_MSG:157:S - com.sap.smdagent.vmmanager.VMManagerP4Exception: com.sap.smdagent.plugins.connectors.p4.exceptions.P4AuthorizationException: Access is denied to SAP System sid: check the connection credentials.More details about the error in agent 'sappi' log file (SMDAgentApplication.X.log).; nested exception is:
com.sap.engine.services.security.exceptions.BaseLoginException: Error during authentication. For more information see the remote server traces.
Any idea?
Thanks.

Deleted CDMA USB Modem from Port Configurations... Can't get it back!

A while back, I was trying out a wireless USB CDMA modem. I didn't really like it and was mainly just using it for testing purposes, and after I was done with it I deleted the port configuration out of my Network Config, thinking A) I'd never need it again and B) It would repopulate or at least be able to be recreated if I wanted to use it again.
Well, this weekend I'm out of town in an area where I don't have an internet connection regularly and need the ability to connect without relying on WIFI. So I reactivated the USB modem and went on my way. As soon as I put the card in, though, nothing happens. Normally the card would automatically detect and even open up its own connection software in the title bar. This time, nothing. So I boot into Windows and test it out there: works fine. Detects, connects, loads webpages, everything. So it's not the card.
I go back into OS X and see if there's anyway to manually add it. I check in System Profiler, and sure enough, under USB the card is recognized. Not in modems, though, but I can't remember if it populated there before. Anyway, I go into Network Config, try to add a port, but the only things available are the typical Ethernet, Airport, Bluetooth, etc. No USB, no CDMA modem, nothing I need.
So what I'm thinking is, when I deleted the old CDMA modem setting in Network Port Configs, its pretty much permanently deleted it. My question is, is there any way for me to manually get it back? I really could use the benefit of this card at the moment.
Thanks for any help,
Bryan

I had not heard of that brand. Out here we get a lot of stuff from China and Korea.
After I wrote that last night, I had a closer look at my settings and the CDMA modem I have is shown in the Network Configurations panel -- yours is not, you say.
Sorry, if I was not clear about the point concerning Bluetooth. That panel provides a list of ALL modem drivers, so I was suggesting that you had a look in there, in case there might be a suitable modem driver you could use.
I had two of these modems (one was stolen) the first used that Null modem driver while the other used a Huawei driver that I had to work hard to make the local company find.
I just looked at the Franklin Support pages and as you say, they do not appear to have a driver listed for Macs, only the user guide.
As a late thought, and not wishing to sound funny at all: have you tried the other USB port? With one of the CDMA modems I had it would work perfectly in one port but in the other the computer never recognised it.
Message was edited by: Graham K. Rogers

Can't run form from Form Builder 10g - Port configuration problem?

Hi,
I have installed the Database (10.2.0.1.0) and the Developer Suite (10.1.2.0.2) on two Linux machines (Red Hat Enterprise Linux ES 4 Basic).
If I enter the frmservlet-URL manually everything seems to be fine.
In one case I enter http://127.0.0.1:8890/forms/frmservlet, in the other http://127.0.0.1:8889/forms/frmservlet; in BOTH cases I get eventually a dark square and the status bar says "Applet oracle.forms.engine.Main started".
HOWEVER, if I create a simple form with Form Builder and click on the Button with the green traffic light ("Run Form"), the form runs only on the machine where frmservlet listens on port 8890.
On the other machine (frmservlet configured to listen on port 8889) Firefox pops up, the URL "http://127.0.0.1:32979/6dOrpwghCqnp8PhMT7KVT533m3IaArqFbPqPBOztZXWYSsNy" gets called, and nothing else happens. The screen displays the string "ORACLE FORMS." and the status bar says "Waiting for 127.0.0.1...", and it stays like this forever.
I assume this is a port configuration problem, but I don't have a clue where to start.
Any suggestions how I should proceed are greatly appreciated.
Thank you very much in advance!

Hi Frank,
Thank you for your reply.
I doublechecked my configuration.
In the dialog Edit --> Preferences --> Runtime the Application Server URL is set to "127.0.0.1:8889/forms/frmservlet".
However, when I attempt to run the form, the URL "http://127.0.0.1:33140/W2dwbV9eXS2fPkuKlxNhCxFWdEihwDviat2uV7ycrSotqwDN" gets called.
The screen displays the string "ORACLE FORMS." and the status bar says "Waiting for 127.0.0.1...", and that's it.
I wonder how the port number 33140 got selected. Interestingly, this time it is a different number; last time it was port 32979. In fact, the port number seems to change each time; I tried again and now it is 33189.
I will now try to set the port number for the frmservlet to 8890.
I choose Edit --> Preferences --> Runtime and set the application server URL to "127.0.0.1:8890/forms/frmservlet".
I stop the container, open /home/oracle/OraHome_1/j2ee/DevSuite/config/default-web-site.xml and change the port number to 8890:
<?xml version="1.0" standalone='yes'?>
<!DOCTYPE web-site PUBLIC "Oracle Application Server 10g XML Web-site" "http://xmlns.oracle.com/ias/dtds/web-site.dtd">



<web-site port="8890" protocol="http"
display-name="Oracle Developer Suite 10g instance of Oracle Containers for J2EE Web Site">

     
     
     <default-web-app application="default" name="defaultWebApp" root="/j2ee" />

<web-app application="forms" name="formsweb" root="/forms" />


<web-app application ="reports" name="web" root="/reports" />
<web-app application = "reports" name="demo" root="/repdemo" />
     
     <access-log path="../log/default-web-access.log" />
</web-site>
I restart the container, start Form Builder, connect to the database, and open my test form.
When attempting to run the form, the URL "http://127.0.0.1:33437/Pl0n3ky9vmU5z37A7ScBnQhsGwq3jwuzJpgTAKWPMOYIzT8K" gets called (again a new port number, apparently picked radomly within a certain range) and nothing happens: "Waiting for 127.0.0.1...".
However, when I enter the URL http://127.0.0.1:8890/forms/frmservlet I do (eventually, after confirming that I trust the certificate etc.) get a darc rectangle and the status message "Applet oracle.forms.engine.Main started", which tells me that my setup can't be that far off target.
Here is the output of netstat:
[root@localhost ~]# netstat -anp --tcp
Active Internet connections (servers and established)
Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name
tcp 0 0 0.0.0.0:32769 0.0.0.0:* LISTEN 2779/rpc.statd
tcp 0 0 0.0.0.0:23910 0.0.0.0:* LISTEN 5269/java
tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN 2759/portmap
tcp 0 0 0.0.0.0:1521 0.0.0.0:* LISTEN 4265/tnslsnr
tcp 0 0 0.0.0.0:113 0.0.0.0:* LISTEN 2983/xinetd
tcp 0 0 127.0.0.1:7830 0.0.0.0:* LISTEN 4429/spamd --port 7
tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN 2928/cupsd
tcp 0 0 0.0.0.0:9240 0.0.0.0:* LISTEN 5269/java
tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN 3002/sendmail: acce
tcp 0 0 0.0.0.0:8890 0.0.0.0:* LISTEN 5269/java
tcp 0 0 0.0.0.0:32795 0.0.0.0:* LISTEN 4231/ora_d000_orcl
tcp 0 0 127.0.0.1:1521 127.0.0.1:32817 ESTABLISHED 4265/tnslsnr
tcp 0 0 127.0.0.1:32817 127.0.0.1:1521 ESTABLISHED 4209/ora_pmon_orcl
tcp 0 0 127.0.0.1:33425 127.0.0.1:1521 ESTABLISHED 5298/frmbld
tcp 0 0 127.0.0.1:1521 127.0.0.1:33425 ESTABLISHED 5311/oracleorcl
tcp 1 0 80.133.127.83:33485 209.132.177.100:443 CLOSE_WAIT 4060/python
tcp 1 0 80.133.127.83:33484 209.132.177.100:443 CLOSE_WAIT 4060/python
tcp 1 0 80.133.127.83:33494 209.132.177.100:443 CLOSE_WAIT 4060/python
tcp 1 0 80.133.127.83:33520 209.132.177.100:443 CLOSE_WAIT 4060/python
tcp 0 0 80.133.127.83:33529 209.132.177.100:443 ESTABLISHED 4060/python
tcp 0 0 80.133.127.83:33528 209.132.177.100:443 ESTABLISHED 4060/python
tcp 1 0 80.133.127.83:33460 209.132.177.100:443 CLOSE_WAIT 4060/python
tcp 1 0 80.133.127.83:33470 209.132.177.100:443 CLOSE_WAIT 4060/python
tcp 0 0 :::22 :::* LISTEN 2968/sshd
tcp 0 0 ::ffff:127.0.0.1:33437 :::* LISTEN 5298/frmbld
tcp 697 0 ::ffff:127.0.0.1:33437 ::ffff:127.0.0.1:33439 CLOSE_WAIT -
tcp 348 0 ::ffff:127.0.0.1:33437 ::ffff:127.0.0.1:33440 CLOSE_WAIT -
[root@localhost ~]#
The question remains: Where do those port numbers come from?
Regards,
jme

Technical Systems in Managed System Configuration greyed .

Hi,
I upgraded ST-SER to 701_2010_1 SP0 and in the process of upgrading
this tool I had to also patch other components like ABAP,BASIS etc as
pre-requisites for this.
As this involved all the components to be patched, I
executed the initial,Basic configuration in solman_setup and everything
is fine.
In Initial I executed only the read SLD and skipped the other steps as
the other steps have been already executed after install of solution
manager .
In Basic Configuration I have executed all steps and everything has
executed successfully.
The problem is in Managed system configuration.
I have the Wily Introscope Manager Console showing all the statistics
of Agents and all Agents are attached.
The problem I see is first thing is the technical setting in the
Managed system diagnostics are greyed why is it ?
Second is when I execute the Managed system Diagnostics configuration , the first step Wily host agent fails all other steps are okay.
The error in this step is "No connection to any Wily Enterprise Manager"
Appreciate any advise.
Thanks,
Misba

Hello Diego,
I started getting this error only after I upgraded the tools, even now the Wily is up and running and I can see the dashboard with all the live diagnostics graphs and statistics for ABAP & JAVA. All the steps have executed successfully except this one step. Even trusted RFC's are okay. This was an established system with all configurations.
So I am surprised what I am missing. Can you please explain to me more about how I can see " http://<ip>:<port>/SMD under "managed systems" ->Introscope Agent ".
All Agents are attached and in Agent adminstration I can see all the Agents online.
Thanks,
Misba

Warnings in Managed System Configuration

Dear all,
We are in the process of connecting a satellite system to Solman 7.1 and to monitor its datas.
So in Managed system configuration for system, we are facing some warnings in step 8 and step 11.
In step 8(Configure Automatically),Generate System level metrics ended with a warning i.e "The Diagnostic Agent for Introscope Enterprise manager could not be found"
In step 11,(Configuration),Configuration check ended with warnings.
i.e Errors found during the last 20 run for extractor
Kindly suggest on how to proceed further.
Thanks,
Regards,
Hasan

Hello Diego,
Sorry for the late reply..
Yea the Enterprise Manager is running.
When i tried the URL which you had given, it is displaying as 404 not found.
Also when i start the Diagnostic agent in the SOLMAN, it is getting started and it is showing green LED in MMC, but when I try to connect the Diagnostic Agent to Solman in Basic configuration step, it is turning yellow and displays as,
""Access denied by the Managing System
Check username/password
Managing System details:
host hllsap12
port 8103
Last operational status 272"
After this the Diagnostic agent turns to yellow in MMC also..
Kindly advice,
Thank You,
Regards,
Hasan

7304 nse100 FE Management Port configuration question

Similar Messages

Maybe you are looking for