ACE Device Manager

How can I use ACE device manager. I have vlans defined on ACE in bridged mode. How can the management interface be defined on ACE. Please provide an example if possible.
Thank you.

I am using ACE-20 module in Cat 6500. How can I address the management interface. Or does it only relate to ACE appliance.

Similar Messages

  • ACE-4710 : Device Manager on Primary ACE cannot authenticate

    Hi,
    In a cluster of redundant ACE-4710, version A5(1.2), the graphical Device Manager on the primary ACE cannot authenticate users. An error message is displayed :
    The strange thing is that the standby ACE Device Manager work correctly. Moreover, both ACE are perfectly synchronized :
    CH01AC03/P-115-A# sh ft group summary
    FT Group                     : 14
    Configured Status            : in-service
    Maintenance mode             : MAINT_MODE_OFF
    My State                     : FSM_FT_STATE_ACTIVE
    My Config Priority           : 200
    My Net Priority              : 200
    My Preempt                   : Enabled
    Peer State                   : FSM_FT_STATE_STANDBY_HOT
    Peer Config Priority         : 150
    Peer Net Priority            : 150
    Peer Preempt                 : Enabled
    Peer Id                      : 1
    No. of Contexts              : 1
    Here is the details on the ACE and DM version :
    CH01AC03/P-115-A# sh ver
    Cisco Application Control Software (ACSW)
    TAC support: http://www.cisco.com/tac
    Copyright (c) 1985-2012 by Cisco Systems, Inc. All rights reserved.
    The copyrights to certain works contained herein are owned by
    other third parties and are used and distributed under license.
    Some parts of this software are covered under the GNU Public
    License. A copy of the license is available at
    http://www.gnu.org/licenses/gpl.html.
    Software
      loader:    Version 0.95.1
      system:    Version A5(1.2) [build 3.0(0)A5(1.2) adbuild_19:38:58-2012/01/17_/auto/adbure_nightly4/renumber/rel_a5_1_2_throttle/REL_3_0_0_A5_1_2]
      system image file: (hd0,1)/c4710ace-t1k9-mz.A5_1_2.bin
      Device Manager version 5.1 (0) 20111215:1009
    What coud be the problem ?
    Thank you
    Yves

    Hello Yves,
    Try with the command "dm reload" in the Admin Context
    Cesar R
    ANS Team

  • ACE 4710 Device Manager Gives Blank Screen

    Hi Guys,
    Wish somebody could share his/her experience on this.
    I have a problem with ACE4710 Device Manager that after entering username and password, it will appear just a blank screen. And it happen also to the FT peer.
    I know that the workaround is to reload the ACE (as it happened one time before) but I wish somebody could share a better or probably permanent solution to this problem.
    Thank you in advance guys.
    Tomy.

    CSCsv95366: Device Manager displays a blank page after login
    Upgrade to A3(2.2) or beyond.
    Gilles.

  • ACE30 - Accessing the ACE Applicance Device Manager

    Hi...
    I've got basic connectivty to our ACE30 module and when I try connecting to the management IP address (attached to the Admin context), I see a very basic GUI which only lists the CSM to ACE config conversion tool.  I don't see a GUI as detailed in the document:
    http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/ace_appliances/vA1_7_/configuration/device_manager/guide/UG_over.html#wp1072950
    How do I get the ACE Applicance Device Manager GUI working so that I can then configure real servers, serverfarms etc rather than via the GUI?
    Having read through copious amount of documentation I can't seem to find a refrence that would help here.  This should be a fairly straight forward exercise - do I need to install some other software to get the full fledged GUI working?
    thanks
    Sheldon

    Only the ACE 4710 appliances have the GUI.   If you are looking for a GUI for the ACE30 module you will need to use Cisco Application Network Manager (ANM)   It will provide the GUI for the ACE30 to be able to configure it.   As you have seen, only the conversion tool is available on the module.

  • Ipod 5th Generation 80 GB / Device Manager / Driver not Installed / Code 28

    Well, where do I begin! Got my 1st Ipod 2 days ago & still unable to use it! I have installed & uninstalled the itunes 7 software numerous times. On phone w/ Apple for 1 hour...followed by online chat help w/ Dell.
    I've tryed 4 different USB ports on my computer. The device Manager shows the Ipod w/ a ? and a ! in yellow. The add new hardware tells me, "Drivers for this device are not installed. Code 28." My computer reconizes that the ipod is plugged in, but will not do anything. There is no communication between the 2. Keeps telling me to insert cd for software for ipod.
    Help! Does seem that other people are having similar issues. I think a software cd should of been provided w/ the ipod....not sure if that would of corrected my problem.

    Hi,
    Click Start > All Programs > Accessories > Run. the Run dialog appears,
    Type %temp%, then click OK.
    locate and enter into the HP Installation temporary folder, start with the 7Z characters.
    If you can see several folders starting with 7Z, locate the latest one.
    Click the Address bar area, then the full address path will appear,
    Copy the full path location by clicking CTRL + P while the path is selected.
    Enter the Device Manager.
    Right click the printer name with the error mark, then click Update Driver.
    Select the second option to manually locate the driver.
    Paste the temporary folder path and click Next (Keep Include Sub Fulders marked), the driver should be updated.
    Please let me know of any change,
    Shlomi
    Say thanks by clicking the Kudos thumb up in the post.
    If my post resolve your problem please mark it as an Accepted Solution

  • IPod is not recognized by Windows, iTunes or Device Manager

    I'm running Windows XP with external hard drive. When hard drive is connected, iPod will not sync and I get message stating "USB Device Not Recognized. One of the USB devices had malfunctioned..."
    When disconnect, iPod will sync. However, iTunes is on external drive; therefore musc is not syncing onto iPod. I've attempted the 5 R's as well as searching for iPod in Device Mananger. When iPod is conncected, it is listed in Devce Manage as "Unknown Device." Articles to solve recommend relettering device, bu how do I get it to be recognized by Device Manager?

    I HAVE A SIMILAR PROBLEM TO THAT I JUST BOUGHT MY 30GB IPOD VIDEO ABOUT 4 HOURS AGO, SINCE THEN I HAVE BEEN REALLY STRUGGLING TO INSTALL IT. A SOON AS I GOT IT, I DID EXACTLY WHAT IT SAID, I WENT TO WWW.APPLE.COM/IPOD/START AND DOWNLOADED THE NEWEST ITUNES VERSION. THEN I PLUGGED IN MY IPOD TO MY COMPUTER, AND ALL THAT HAPPENS IS A LITTLE BUBBLE OPENS UP AND SAYS "FOUND NEW HARDWARE" WHEN I CLICK THAT, IT OPENS UP, AND I CLICK "INSTALL THE SOFTWARE AUTOMATICALLY" WHERE IT SAYS IT, THEN I CLICK NEXT AND WAIT. AFTER, IT SAYS "THE HARDWARE WAS NOT INSTALLED BECAUSE THE WIZARD CANNOT FIND THE NECESARRY SOFTWARE".AFTER I WENT TO WWW.APPLE.COM TO FIND OUT WHAT THE PROBLEM WAS, I'VE LOOKED THROUGH AND READ EVERY ARTICLE THAT CAN PERTAIN TO MY SITUTAION, BUT NONE HAVE HELPED ME I AM DISPLEASED TO SAY, THE LAST ARTICLE I READ WAS THIS ONE:
    http://docs.info.apple.com/article.html?artnum=305136
    BUT EVEN THAT DOES NOT HELP ME BECAUSE WHEN I GET TO STEP 8 WHICH SAYS "Locate the iPod in this list. In some cases one of the entries will have "iPod" in its name. If no such entries are present, the iPod is most likely represented by "USB Mass Storage Device." I LOOK FOR WHERE IT SAYS "IPOD" OR "USB MASS STORAGE DEVICE" UNDER "UNIVERSAL SERIAL BUS CONTROLLERS, AND CANNOT FIND EITHER THING..I HAVE RESTARTED MY COMPUTER A NUMBER OF TIMES, I HAVE EVEN UNISTALLED ITUNES THEN REINSTALLED IT I HAVE STRETCHED EVERY OPTION AND NOTHING HAS WORKED..CAN SOME ONE PLEASE HELP ME??..I HAVE BEEN TRYING TO SOLVE THIS PROBLEM FOR 4 HOURS STRAIGHT STOPPING ONLY TO GO TO THE BATHROOM AND GRAB A BITE TO EAT..

  • [solved] Digital Camera not recognized in device-manager

    My digital camera "Canon Powershot SX120 is" is not recognized by the devicemanager. I have read Digital Cameras.
    $ groups
    wheel storage users printadmin
    The "camera"-Group isn't needed anymore and this group doesn't exist on my system.
    The Powershot SX 120 has a  MTP/PTP connection mode (as the manual says). But:
    # mtp-detect
    Unable to open ~/.mtpz-data for reading, MTPZ disabled.libmtp version: 1.1.6
    Listing raw device(s)
    No raw devices found.
    gphoto succeed:
    $ gphoto2 --auto-detect
    Modell Port
    Canon PowerShot SX120 IS usb:002,019
    A gphoto --summary could be found here
    There is no udev-rule for this camera. If i create one while copying a rule from a similar camera from /etc/udev/rules.d/69-libmtp.rules, and store it into /etc/udev/rules.d/69-canon.rules, the device-manager shows up. My udev-rule:
    # Canon PowerShot SX120AX (PTP/MTP mode)
    ATTR{idVendor}=="04a9", ATTR{idProduct}=="31e0", SYMLINK+="libmtp-%k", ENV{ID_MTP_DEVICE}="1", ENV{ID_MEDIA_PLAYER}="1"
    The device-manager shows me only the option to open with a file-manager. Doing so will result in an error:
    The file or folder udi=/org/kde/solid/udev/sys/devices/pci0000:00/0000:00:02.1/usb2/2-8/ do not exist.
    With my udev-rule:
    solid-hardware listen
    Object::connect: No such signal org::freedesktop::UPower::DeviceAdded(QDBusObjectPath)
    Object::connect: No such signal org::freedesktop::UPower::DeviceRemoved(QDBusObjectPath)
    Listening to add/remove events:
    Device Added:
    udi = '/org/kde/solid/udev/sys/devices/pci0000:00/0000:00:02.1/usb2/2-8'
    Without the active udev-rule, "solid-hardware listen" produces nothing, but
    udevadm monitor
    monitor will print the received events for:
    UDEV - the event which udev sends out after rule processing
    KERNEL - the kernel uevent
    KERNEL[5077.662572] add /devices/pci0000:00/0000:00:02.1/usb2/2-8 (usb)
    KERNEL[5077.662655] add /devices/pci0000:00/0000:00:02.1/usb2/2-8/2-8:1.0 (usb)
    UDEV [5077.681178] add /devices/pci0000:00/0000:00:02.1/usb2/2-8 (usb)
    UDEV [5077.693035] add /devices/pci0000:00/0000:00:02.1/usb2/2-8/2-8:1.0 (usb)
    Don't know what to do ... is a udev-rule necessary to bring up the message from device-manger? Or is the Camera not recognized as a mtp-device (the Camera has no such settings)? How could i figure it out?
    With Digikam i could import Fotos, but i would do so with gwenview. I've tried to check it out with gwenview_importer:
    $ gwenview_importer --udi '/org/kde/solid/udev/sys/devices/pci0000:00/0000:00:02.1/usb2/2-8'
    QDBusConnection: session D-Bus connection created before QCoreApplication. Application may misbehave.
    gwenview_importer: Missing required source folder argument.
      (don't care about the different udi, i took this example from a former try) but i don't know, how to find out where the "source folder" is ...
    Last edited by quiqueck (2014-02-26 20:10:25)

    I have solved this by making an extra udev-rule for my camera. See my adventure on forum.kde.org for details

  • After updating to Windows 8.1 the Webcam in my Inspiron is gone and Imaging devices missing in Device Manager

    my webcam in my Dell Inspiron 3521 was working fine with Windows 8.  After updating to Windows 8.1 the Webcam in my computer is gone and the 'Imaging devices' is  missing in the Device Manager.  how can I get the Webcam back? 
    thank you very much.

    I don't see anything specific to your webcam issue but there are a number of Windows 8.1 related drivers listed on the Support site.
    http://www.dell.com/support/home/us/en/04/product-support/product/inspiron-15-3521/drivers
    The Dell Update utility will recommend drivers that are needed specific to your model.
    http://www.dell.com/support/home/us/en/04/Drivers/DriversDetails?driverId=860YD&fileId=3374847033&osCode=WB64A&productCode=inspiron-15-3521&languageCode=EN&categoryId=AP
    Good luck!
    bill
    Regards, Bill Moore @BMooreAtDell

  • Problem With Device Management in Campus Manager

    hi , there are 474 devices in common services device managemant which I grouped them to userdefinedgroups .
    then I applied the auto allocation mode in Campus manager to apply all managed devices , when I click apply it mentioned that it would add 474 devices . but after data collection was finished just 461 devices was added and the rest of those are now in the Include devices under device management !!!
    why does it hapened ?   
    thank you .

    Hi Marian,
    Could you please provide me with details on how to setup test workbench reporting. I have a BW system external to Solution Manager. I have setup the RFC conncections and all is okay. I have also setup the source system in BW and installed the web templates. However, when activating the content via solman_workcenter - test management - settings, I get the following error:
    Content Activation Log
    Log for Setup ID 20100819135323
    20100819 135323[ERROR ]: Current Status: ERROR
    20100819 135323[INFO ]: Job CCMS_BI_SETUP successfully scheduled
    20100819 135323[ERROR ]: Incorrect system setting: standard transport is active
    20100819 135323[ERROR ]: Change system settings or set user parameters RSOISCONTENTSYSTEM and RSOSTANDARDCTOACTIVE
    20100819 135323[ERROR ]: Prerequisites check failed
    20100819 135323[ERROR ]: Jobname/count: CCMS_BI_SETUP 13532300
    I am sure there is something wrong in my setup but I cannot figure out what it is. A step by step help on how to do it will be greatly appreciated.
    Regards,
    Rue.

  • Just boot camped mid-2012 MBP using Apple's BootCamp 5.1.5621. However, no wireless adapter is listed in device manager

    [In Windows 8.1] When I access the Device Manager, it does not list my wireless adapter as one of the devices available. I have attempted to manually install the drivers from the BootCamp 5.1.5621 file.
    I've spent several hours attempting to remedy this but have only found threads explaining how to solve the problem if the 802 adapter is already listed in the device manager.

    I recently had some BT issue's in Win8 so I wrote a topic about this subject. Maybe you need to replace the Broadcom drivers as well.
    Please have a look here:
    Apple Wireless Keyboard Windows 8 problem
    Good luck.
    Marcel

  • Unable to open 2 9509 switches at the same time in Cisco Device Manager

    Dear Friends,
    There are a pair of MDS 9509 switches whose management addresses are 172.16.2.197 and 172.16.2.198.
    When we try to manage these Devices through Cisco device manager, the first device opens up without any problem, but when the second 9509 is opened in Cisco Device Manager, it fails giving the following error message:
    "Open udp transport failed: Address already in use: Cannot bind"
    To get around this issue, if we close the first interface to the 9509 switch, then we are able to open up the second 9509 in Device Manager.
    We have this problem only in Cisco device manager. If we open one switch in Cisco device manager and the other switch in Cisco Fabric Manager, it works.
    Also, we can telnet to both the devices successfully at a time.
    The device manager in use is 4.1.
    Please find enclosed the sh version outputs for your kind reference.
    Can you please help me understand the cause of this issue?
    Thanks a lot
    Gautam

    Is it always the same MDS that fails to open, or can you open either one first, and then the second one poses the problem (no matter which one is second)?
    Can you try from a second work station and see if you can open DM to both switched at the same time? I suspect the address it is complaining about is the local workstation IP, not the MDS IP.
    If you open the FM map, then you click on the MDS ICONs, can you open DM to both MDS?
    - Mike

  • Questions on mobile device management

    Hi All,
    I'm not sure where to post this question since I couldn't find a forum specific to Afaria, so thought someone here might be able to help.
    1. Afaria mobile device management solution claims that data and content is backed up and can be deleted if a device is stolen or lost. Can this deletion be done if the mobile is switched off of the SIM card has been removed? What is the mechanism of the data deletion process when the device is either ON/OFF?
    2. How does Afaria handle online and offline user authentication? If a mobile app is opened, can Afaria be configured to force the user to enter credentials for authentication? Or should there be a separate login page as a part of the mobile app? (The user's credentials are needed to find his role from LDAP and the rest of the app to work properly, which is y the question).
    Thanks & Regards,
    Vaishnavi

    This forum is fine for Afaria discussions and questions, no worries. 
    1.  If mobile device is switched off or not network connected then Afaria is not able to do anything with that device.  The content though would be secured, encrypted etc. so that there should be no risk as long as the device is switched off.  The "kill device" command that can be sent from Afaria will work if device is turned on and connected to a network.
    2.  Afaria can force quite a lot of things and one of them is regarding the device itself, forcing a password/pin type of unlocking.  The mobile app normally has it's own mechanism for authentication, user name and password.  That is a SUP function and has little to do with Afaria, I don't believe Afaria can force that part of authentication. 
    You can get a good overview of the technical part of Afaria here:  [Afaria Technical White paper|http://www.sybase.com/files/White_Papers/Afaria-Technical-WP.pdf]

  • After upgrading to mountain lion,my HP device manager can't find scanner

    I have an HP Photosmart C5550 All-in-One printer scanner.
    The HP device manager can't find the scanner. Printer works fine.
    I upgraded from Lion to Mountain Lion and this is my problem now.

    Try the HP Photosmart C5500 series app in /username/Library/Printers/, HP Utility->Devices in /Library/Printers/hp/Utilities/, Image Capture, or Preview->File->Import from scanner option.

  • How do I reformat an IPod Touch for Windows that has been formatted for a Mac?  All instructions I have been able to find use ITunes or Device Manager to reformat.  My IPod is not being recognized by ITunes or in Device Manager.

    I have an IPod Touch that has been formatted for a Mac.  All instructions I have been able to find use ITunes or Device Manager to reformat the device for Windows.  This cannot be done if Windows doesn't recognize the device.  Is there another way to set the device back to the factory settings directly on the device without using ITunes?

    Ipod touch is not formatted one way or the other at all.
    Just sync it to the new computer using itunes.
    iPod touch User Guide (For iOS 5.1 Software)

  • The Ultimate Guide to Resolving Profile and Device Manager Issues

    The following article also applies to issues after re-setting the severs' hostname. It also applies to situations where re-setting the Code Signing Certifictateas described by Apple has not resolved the issue.
    Hello,
    I have been plagued with Profile Manager and Device Manager issues since day one.
    I would like to share my experience and to suggest a way how to resolve issues such as device cannot be enrolled or Code Signing Certificate not accepted.
    I shall try to be as brief as possible, just giving an overview of the steps that resolved my issues. The individual steps have been described elsewhere in this forum. For users who have purchased commercial SSL certs the following may not apply.
    In my view many of these issues are caused by missing or faulty certificates. So let us first touch on the very complex matter of certificates.
    Certificates come in many flavours such as CA (Certificate Authority), Code Signing Certificate, S/MIME and Server Identification.
    (Mountain?) Lion Server creates a so-called Intermediate CA certificate (IntermediateCA_hostname_1") and Server Identification Certificate ("hostname") when it installs first. This is critical for the  operation of many server functionalities, including Open Direcory. These certs together with the private/public keys can be found in your Keychain. Profile  and Device Manager may need a Code Signing Certificate.
    The most straightforward way to resolve the Profile Manaher issues is in my view to reset the server created certicates.
    The bad news is that this procedure involves quite a few steps and at least 2 hours of your precious time because it means creating a fresh Direcory Master.
    I hope that I have not forgotten to mention an important step. Readers' comments and addenda are welcome.
    I shall outline a sensible strategy:
    1. Clone your dysfunctional server to an external harddrive (SuperDuper does a reliable job)
    2. Start the server fom the clone and shut down ALL services.
    3. It may be sensible to set up a root user access.
    4. Back-up all user data such as addess book, calendar and other data that you *may* need to set up your server.
    5. Open Workgroup Manager and export all user and workgroup accounts to the drive that you using to re-build your server (it may cause problems if you back-up to an external drive).
    6. Just in case you may also want to back-up the Profile Manager database and erase user profiles:
    In Terminal (this applies to Lion Server - paths may be diferent in Mountain Lion !)
    Backup: sudo pg_dump -U _postgres -c device_management > $HOME/device_management.sql
    Erase database:
    sudo /usr/share/devicemgr/backend/wipeDB.sh
    7. Note your Directory (diradmin) password for later if you want to re-use it.
    8. Open Open Server Admin and demote OD Master to Standalone Directory.
    9. In Terminal delete the old Certificate Authority
    sudo rm -R /var/root/Library/Application\ Support/Certificate\ Authority/
    This step is crucial because else re-building you OD Master will fail.
    9. Go back to Server Admin and promote the Standalone Directory to OD Master. You may want to use the same hostname.
    10. When the OD Master is ready click on Overview and check that the LDAP and Keberos Realm reflect your server's hostname.
    11. Go back to Workgroup Manager and re-import users and groups.
    NOTE: passwords are not being exported. I do not know how to salvage user passwords. (Maybe passwords can be recovered by re-mporting an OD archive - comments welcome! ).
    12. Go to Server App and reset passwords and (not to forget) user homefolder locations, in particular if you want to login from a network account!
    If the home directory has not been defined you cannot login from a network account.
    13. You may now want to restore Profile Manager user profiles in Terminal. Issue the following commands:
    sudo serveradmin stop devicemgr
    sudo serveradmin start postgres
    sudo psql -U _postgres -d device_management -f $HOME/device_management.sql
    sudo serveradmin start devicemgr
    14. You can now switch back on your services, including Profile Manager.
    In Profile Manager you may have to configure Device Management. This creates a correct Code Signng Certicate.
    15. Check the certificate settings in Server App -> Hadware -> Settings-> SSL Certificates.
    16. Check that Apple Push Notifications are set.(you easily check if they are working later)
    17. You may want to re-boot OS Server from the clone now.
    18. After re-boot open Server App and check that your server is running well.
    19. Delete all profiles in System Preferences -> Profiles.
    19. Login to Profile Manager. You should have all users and profiles back. In my experience devices have to be re-enrolled before profiles can be pushed and/or devices be enrolled. You may just as well delete the displayed devices now.
    20. Grab one of your (portable) Macs that you want to enrol and go to (yourhostname)/mydevices and install the server's trust profile. The profile's name  should read "Trust Profile for...) and underneath in green font "Verified".
    21. Re-enrol that device. At this stage keep your finger's crossed and take a deep breath.
    22. If the device has been successfully enrolled you may at last want to test if pushing profiles really works. Login to Profile Manager as admin, select the newly enrolled device. Check that Automatic Push is enabled (-> Profile -> General). Create a harmless management profile such as defining the dock's position on the target machine. (Do not forget to click SAVE at the end - this is easily missed here). If all is well Profile Manager will display an active task (sending) and the dock's position on the target will have changed in a few seconds if you are on a LAN (Note: If sending seems to take forever: check on the server machine and/or on your router that the proper ports are open and that incoming data is not intercepted by Little Snitch or similar software).
    Note: if you intend to enrol an Apple iPhone you may first need to install the proper Apple Configuration software.
    Now enjoy Profile and Device Manager !
    Regards,
    Twistan

    HI
    1. In Action profiles, logon to system and recheck correcion are available in action definition as well in condition configuration and the schedule condition is also maintained. but the display is not coming(i.e in the worklist this action is not getting displayed).
    You can check the schedule condition for the action and match the status values...or try recreating the action with schedule condition again....for customer specific ....copy the standard aciton with ur zname and make a schedule condition and check the same.
    2, In suppport team of incident when i give individual processor it throwing a warning that u r not the processor. but when i give org unit it is working perfectly. Could anyone guide on this.
    You need to have the empolyee role for BP ..goto BP and got here dropdown for ur bp and choose role Employee and then enter ur userid
    also make sure that u have the message processing role
    Hope it clarifies ur doubt and resolve ur prob
    Regards
    Prakhar

Maybe you are looking for