AP with EAP and managment control through ACS
I have deployed a number of wireless networks with EAP authenticated through the users domain account details passed to ACS 4.1. This appears to work fine, but I have two questions regarding control of access.
1. I have configured RADIUS for the EAP and then added TACACS+ for the management access of the AP. Although going back to the same ACS server with different protocols I am unable to get the managment access control to work if both are active? Should this work?
2. How do I control which VLAN / SSID a user has access to? it seems as though there is no way to limit them to a specific SSID (other than not telling them it) If the users have a guess at the SSID then the possibility is that they can access a LAN they should not.
Any help would be very greatfully received.
Hi ihill,
in answer to your second question there is a couple of ways that you can do this depending on the amount of control you have over your clients.
You could use dynamic VLAN assignment:
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml
You could use Active Directory wirelss group policy to define prefered wirless networks for your clients
Or you could use a 3rd party supplicant like the Juniper Network's Odyssey Access Client
http://www.juniper.net/products_and_services/aaa_and_802_1x/odyssey/odyssey_access_client/
hope this helps
Mark
*pls rate all useful posts
Similar Messages
-
Hi *,
I have the following problem with RADIUS and EAP authentication.
Radius server sends an "Access-Accept" packet to my AP, but the station does not authenticate.
I've tried with different encryption configuration and with different authentication methods under "dot11 essid", but nothing changes...
What could it be?
Debug piece and configuration follows:
*Jan 25 14:23:34.795: RADIUS/ENCODE(00000012): acct_session_id: 17*Jan 25 14:23:34.795: RADIUS(00000012): sending*Jan 25 14:23:34.799: RADIUS: 4E 47 56 7A 78 65 4A 4F 55 31 47 40 77 6C 61 6E [NGVzxeJOU1G@wlan]*Jan 25 14:23:34.799: RADIUS: 2E 6D 6E 63 30 30 31 2E 6D 63 63 30 30 31 2E 33 [.mnc001.mcc001.3]*Jan 25 14:23:34.799: RADIUS: 67 70 70 6E 65 74 77 6F 72 6B 2E 6F 72 67 [gppnetwork.org]*Jan 25 14:23:34.799: RADIUS: NAS-Port-Type [61] 6 802.11 wireless [19]*Jan 25 14:23:34.799: RADIUS: NAS-Port [5] 6 265 *Jan 25 14:23:34.799: RADIUS: NAS-Port-Id [87] 5 "265"*Jan 25 14:23:34.799: RADIUS: NAS-IP-Address [4] 6 192.168.173.2 *Jan 25 14:23:34.811: RADIUS/DECODE: EAP-Message fragments, 20, total 20 bytes*Jan 25 14:23:34.831: RADIUS/ENCODE(00000012):Orig. component type = DOT11*Jan 25 14:23:34.831: RADIUS: AAA Unsupported Attr: ssid [265] 8 *Jan 25 14:23:34.831: RADIUS: 57 69 66 69 45 41 [WifiEA]*Jan 25 14:23:34.831: RADIUS: AAA Unsupported Attr: interface [157] 3 *Jan 25 14:23:34.831: RADIUS: 32 [2]*Jan 25 14:23:34.831: RADIUS(00000012): Config NAS IP: 192.168.173.2*Jan 25 14:23:34.831: RADIUS/ENCODE(00000012): acct_session_id: 17*Jan 25 14:23:34.835: RADIUS(00000012): sending*Jan 25 14:23:34.835: RADIUS: 10 01 00 01 07 05 00 00 D9 37 C3 D9 79 3E 33 EA [?????????7??y>3?]*Jan 25 14:23:34.835: RADIUS: F3 7D 73 43 BF BA D0 6A [?}sC???j]*Jan 25 14:23:34.835: RADIUS: NAS-Port-Type [61] 6 802.11 wireless [19]*Jan 25 14:23:34.835: RADIUS: NAS-Port [5] 6 265 *Jan 25 14:23:34.835: RADIUS: NAS-Port-Id [87] 5 "265"*Jan 25 14:23:34.835: RADIUS: NAS-IP-Address [4] 6 192.168.173.2 *Jan 25 14:23:35.035: RADIUS: Received from id 1645/64 192.168.177.158:1812, Access-Challenge, len 304*Jan 25 14:23:35.039: RADIUS: 46 10 78 5F 5F B0 CB 6C 0B 05 00 00 DA C3 BF 28 [F?x__??l???????(]*Jan 25 14:23:35.039: RADIUS: E0 18 2B 95 97 C2 0A D7 40 53 FE 62 [??+?????@S?b]*Jan 25 14:23:35.039: RADIUS(00000012): Received from id 1645/64*Jan 25 14:23:35.039: RADIUS/DECODE: EAP-Message fragments, 60+220, total 280 bytes*Jan 25 14:23:35.355: RADIUS/ENCODE(00000012):Orig. component type = DOT11*Jan 25 14:23:35.355: RADIUS: AAA Unsupported Attr: ssid [265] 8 *Jan 25 14:23:35.355: RADIUS: 57 69 66 69 45 41 [WifiEA]*Jan 25 14:23:35.355: RADIUS: AAA Unsupported Attr: interface [157] 3 *Jan 25 14:23:35.359: RADIUS: 92 DA 5E 26 CF 40 01 22 7A 8E F5 C1 [??^&?@?"z???]*Jan 25 14:23:35.359: RADIUS: NAS-Port-Type [61] 6 802.11 wireless [19]*Jan 25 14:23:35.359: RADIUS: NAS-Port [5] 6 265 *Jan 25 14:23:35.359: RADIUS: NAS-Port-Id [87] 5 "265"*Jan 25 14:23:35.359: RADIUS: NAS-IP-Address [4] 6 192.168.173.2 *Jan 25 14:23:35.367: RADIUS: Received from id 1645/65 192.168.177.158:1812, Access-Accept, len 30*Jan 25 14:23:35.367: RADIUS: authenticator 8C 2C 1B 97 82 BB 6C 7F - AA D3 4A AB CA 22 8B B7*Jan 25 14:23:35.367: RADIUS: EAP-Message [79] 10 *Jan 25 14:23:35.367: RADIUS: 03 01 00 04 00 00 00 00 [????????]*Jan 25 14:23:35.371: RADIUS(00000012): Received from id 1645/65*Jan 25 14:23:35.371: RADIUS/DECODE: EAP-Message fragments, 8, total 8 bytes*Jan 25 14:23:35.671: %DOT11-7-AUTH_FAILED: Station d023.dbb8.d6a9 Authentication failed
Config:
aaa new-model!aaa group server radius rad_eap server-private 192.168.177.158 auth-port 1812 acct-port 1813 key 7 044803071D2448!aaa authentication login eap_methods group rad_eapaaa authorization exec default if-authenticated aaa authorization network default if-authenticated ! aaa session-id commonip name-server 192.168.177.45! dot11 ssid WifiEAP1 vlan 10 authentication open eap eap_methods authentication shared eap eap_methods authentication key-management wpa optional guest-mode! bridge irb! interface Dot11Radio0 no ip address no ip route-cache ! encryption vlan 10 mode ciphers aes-ccm tkip wep128 ! broadcast-key vlan 10 change 300 ! ssid WifiEAP1 ! antenna gain 0 station-role root! interface Dot11Radio0.10 encapsulation dot1Q 10 native no ip route-cache bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled! interface GigabitEthernet0 ip address 192.168.173.3 255.255.255.0 no ip route-cache! interface GigabitEthernet0.1 encapsulation dot1Q 10 native no ip route-cache bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled! interface BVI1 ip address 192.168.173.2 255.255.255.0 no ip route-cache!ip radius source-interface BVI1 bridge 1 route ip
thanks so much!Stefano: not sure if related but there is an unsupported attribute in the debugs:
Jan 25 14:23:35.355: RADIUS: AAA Unsupported Attr:
*Jan 25 14:23:35.355: RADIUS: 57 69 66 69 45 41
*Jan 25 14:23:35.355: RADIUS: AAA Unsupported Attr: interface
Try to eliminate any configured attributes on radius except those in IETF radius. Then try again.
You may also chech by removing the shared eap as suggested above. Let us know if this works.
Sent from Cisco Technical Support iPad App -
Problems with parity and flow control using visa serial
I am trying to create a basic user interface with the options that my
company uses most often for a force indicator. You can configure
the indicator over serial, as well as read the values off the
indicator. I am trying to create the user interface so that using
producer/consumer loops with events, once you change a value, it will
write that new value to the serial port, ie the device.
The problem I am having is transfering the parity and flow control
values for the serial config to the Basic read write VI. The
problem is that once the consumer loop executes, it will write the
values correctly to the VI, but then the outer loop executes 200 ms
later and clears the values. I know that this is normal behavior
and that in order to keep the values stored, normally you would use a
shift register. I tried to use this and had some issues with
correct data types/array mis-mtaches, ets, so I created an indicator
and had a local vaible read the indicator, which seems to be working
for the stop bits, read bits, baud rate, etc, but not the parity anf
flow control. I always get "blank" outputs for theses values (if
you enable the digital display you can see that they are outputing the
value 0 which correspondes to None in both cases, which is
correct). Even though it appears that it is outputting the
correct value, I get an error that says the VISA property is
invalid. I initally did a search and found that my stop bit
control was wrong (outputting double instead of integer), but I could
not find anything on the parity/flow control issue. I even tried
to copy the serial config controls from the basic serial read/write to
my dialog box and that did not work either.
I would be grateful for any suggestions.
Thanks
Kenny
Kenny
Attachments:
BGI_main pandc.zip 232 KBI should add that I am using LV 8.0 and that the serial config
indicator in the consumer loop will be off the frontpanel in the final
VI so that it is not visible to the user.
Kenny -
Nokia E50, issues with connecting and managing mes...
Hi
I'm using Nokia E50 and Nokia PC Suite for a few years now on. Recently I wanted to do my usual maintenance task: copy all messages to PC and delete them from the phone. Issues start here.
At first I had problems with connecting but finally I manage to do it. After dozens of tries PC Suite finally updated contact list. Then I moved to messages tab. It took a while to download all messages (aprox. 700 in inbox, 600 in sent - I had many more few times before when everything was working ok). I can copy them to PC, but I can't delete them. After selecting message(s), trash icon is grayed out (menu item too). I can read message but can't delete it. Why?
I've downloaded latest version of Ovi to see if that would help. Ovi managed to download contact list (after a loong waiting) but failed to download any message. Messages says that it's trying but after one hour nothing happend.
I'm trying this on 2 different machines (Windows 7 and Windows XP), with cable and blue tooth. Efects are always the same. Phone is connected because I can copy files, but when I'm trying to download messages or do backup, software says phone is not connected or tries to copy data with no luck.
Any hint will be appreciated.
Thanks
MaroonedAfter deleting aprox. 150 messages from Inbox and from Sent, both programs were able to download complete list of messages and PC Suite finally reenabled trash icon.
Seems like too much messages causes those program to fail? And why in the past they were working properly with bigger amount of messages?
Well.. one can say "problem solved" but will reappear again in the future with lots of messages. I need to remember to grab them from the phone more frequent. -
Overlay: image gallery with swipe and page control
Hi,
I'm in my first approach with DPS and I can't understand how to create an image gallery swipe controlled with the page control on the bottom part (page control is rapresented by those little circles on the bottom part of the image that shows how many images are shown by the gallery. See this image for a page control example: http://gtiapps.com/wp-content/gallery/p681_gallery/page1.png ).
I tried to read the documentation and the DPS tips but I can't see this simple kind of gallery.
I'm sure I already saw this kind of gallery in DPS-like apps like Wired, I can't believe is some kind of html based gallery (and if it is, anybody could link me a page where I can get the code snippet for that?).
I'm using inDesign CS6 on OsX.
Please give me some suggestions to get this interaction,
thank you in advance,
Bye!It's definitely HTML. Here is a list of a whole bunch of them...
http://www.tripwiremagazine.com/2012/12/jquery-carousel.html
I'm a big fan of roundabout at fredhq.com
You can also make something similar using buttons, and an MSO, not quite the same, but if you don't want to delve into HTML, it will do the job. The dots on the bottom can be buttons. I don't have a machine handy to try and see if you can make the MSO swipe blue, but it is worth a try.
A note about using HTML in a folio. Make sure you have the HTML in its own folder, with all the assets needed, but nothing else. Anything else in that folder will also be included in the folio. (I.e. if you just put the HTML in the folder with your indesign doc, when you included the web overlay, the indesign doc, would also be uploaded. Clear folder organization is key for dps projects. -
Embed pdf in website, show one page at a time, with forward and back controls?
Hi,
Not sure if this is possible (or if this is the right place to ask), but I need to take a multiple page pdf, embed it in a website so its on the left half of the screen, have it only show one page at a time, and have the forward and back page controls.
Is this possible, and if so, could someone point me in the right direction?Typically you would save it to a JPeg and post those on the web site. Expecting a PDF to show up depends on the client computer configuration and browser. This is too risky, unless you don't mind getting nasty little notes that it does not work. If you do it with JPegs, then all the browsers I know of can handle it. Then simply put the PDF separately for those who prefer to download the PDF and look at it separately.
-
Problems with scrolling and Mission Control
I have this problem:
When scrolling down any page, the letters will blur at the top of the screen and not the bottom.
When swiping acrross pages in the launchpad, it occasionaly freezes half way between the two.
When I swipe up with four fingers to access mission control, the screen becomes very sluggish. Swiping back down (or clicking a tab) is even worse, causing slow "laggy" animations.
And this the report from EtreCheck:
Hardware Information:
MacBook Pro (13-inch, Mid 2012)
MacBook Pro - model: MacBookPro9,2
1 2.5 GHz Intel Core i5 CPU: 2 cores
4 GB RAM
Video Information:
Intel HD Graphics 4000 - VRAM: 1024 MB
System Software:
OS X 10.9.2 (13C1021) - Uptime: 0 days 0:3:16
Disk Information:
APPLE HDD HTS545050A7E362 disk0 : (500.11 GB)
EFI (disk0s1) <not mounted>: 209.7 MB
Macintosh HD (disk0s2) / [Startup]: 499.25 GB (309.44 GB free)
HL-DT-ST DVDRW GS41N
USB Information:
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Computer, Inc. IR Receiver
Apple Inc. BRCM20702 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. FaceTime HD Camera (Built-in)
FireWire Information:
Thunderbolt Information:
Apple Inc. thunderbolt_bus
Configuration files:
/etc/hosts - Count: 1
Launch Daemons:
[loaded] com.adobe.fpsaud.plist Support
[loaded] com.microsoft.office.licensing.helper.plist Support
Launch Agents:
[not loaded] com.bose.soundtouch.plist Support
User Launch Agents:
[loaded] com.adobe.ARM.[...].plist Support
[loaded] com.google.keystone.agent.plist Support
[running] com.spotify.webhelper.plist Support
User Login Items:
iTunesHelper
Spotify
BitTorrent
Autodesk 360
Internet Plug-ins:
SharePointBrowserPlugin: Version: 14.0.0 Support
FlashPlayer-10.6: Version: 13.0.0.201 - SDK 10.6 Support
AdobePDFViewer: Version: 10.0.0 Support
Flash Player: Version: 13.0.0.201 - SDK 10.6 Support
QuickTime Plugin: Version: 7.7.3
Default Browser: Version: 537 - SDK 10.9
Audio Plug-ins:
BluetoothAudioPlugIn: Version: 1.0 - SDK 10.9
AirPlay: Version: 2.0 - SDK 10.9
AppleAVBAudio: Version: 203.2 - SDK 10.9
iSightAudio: Version: 7.7.3 - SDK 10.9
iTunes Plug-ins:
Quartz Composer Visualizer: Version: 1.4 - SDK 10.9
3rd Party Preference Panes:
Flash Player Support
Time Machine:
Time Machine not configured!
Top Processes by CPU:
2% WindowServer
2% SoundTouch music server
0% fontd
0% BitTorrent
0% mds
Top Processes by Memory:
90 MB mds_stores
86 MB Safari
78 MB Spotify
57 MB Spotify Helper
49 MB ocspd
Virtual Memory Information:
1.83 GB Free RAM
1.44 GB Active RAM
190 MB Inactive RAM
558 MB Wired RAM
303 MB Page-ins
0 B Page-outsI have this problem:
When scrolling down any page, the letters will blur at the top of the screen and not the bottom.
When swiping acrross pages in the launchpad, it occasionaly freezes half way between the two.
When I swipe up with four fingers to access mission control, the screen becomes very sluggish. Swiping back down (or clicking a tab) is even worse, causing slow "laggy" animations.
And this the report from EtreCheck:
Hardware Information:
MacBook Pro (13-inch, Mid 2012)
MacBook Pro - model: MacBookPro9,2
1 2.5 GHz Intel Core i5 CPU: 2 cores
4 GB RAM
Video Information:
Intel HD Graphics 4000 - VRAM: 1024 MB
System Software:
OS X 10.9.2 (13C1021) - Uptime: 0 days 0:3:16
Disk Information:
APPLE HDD HTS545050A7E362 disk0 : (500.11 GB)
EFI (disk0s1) <not mounted>: 209.7 MB
Macintosh HD (disk0s2) / [Startup]: 499.25 GB (309.44 GB free)
HL-DT-ST DVDRW GS41N
USB Information:
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Computer, Inc. IR Receiver
Apple Inc. BRCM20702 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. FaceTime HD Camera (Built-in)
FireWire Information:
Thunderbolt Information:
Apple Inc. thunderbolt_bus
Configuration files:
/etc/hosts - Count: 1
Launch Daemons:
[loaded] com.adobe.fpsaud.plist Support
[loaded] com.microsoft.office.licensing.helper.plist Support
Launch Agents:
[not loaded] com.bose.soundtouch.plist Support
User Launch Agents:
[loaded] com.adobe.ARM.[...].plist Support
[loaded] com.google.keystone.agent.plist Support
[running] com.spotify.webhelper.plist Support
User Login Items:
iTunesHelper
Spotify
BitTorrent
Autodesk 360
Internet Plug-ins:
SharePointBrowserPlugin: Version: 14.0.0 Support
FlashPlayer-10.6: Version: 13.0.0.201 - SDK 10.6 Support
AdobePDFViewer: Version: 10.0.0 Support
Flash Player: Version: 13.0.0.201 - SDK 10.6 Support
QuickTime Plugin: Version: 7.7.3
Default Browser: Version: 537 - SDK 10.9
Audio Plug-ins:
BluetoothAudioPlugIn: Version: 1.0 - SDK 10.9
AirPlay: Version: 2.0 - SDK 10.9
AppleAVBAudio: Version: 203.2 - SDK 10.9
iSightAudio: Version: 7.7.3 - SDK 10.9
iTunes Plug-ins:
Quartz Composer Visualizer: Version: 1.4 - SDK 10.9
3rd Party Preference Panes:
Flash Player Support
Time Machine:
Time Machine not configured!
Top Processes by CPU:
2% WindowServer
2% SoundTouch music server
0% fontd
0% BitTorrent
0% mds
Top Processes by Memory:
90 MB mds_stores
86 MB Safari
78 MB Spotify
57 MB Spotify Helper
49 MB ocspd
Virtual Memory Information:
1.83 GB Free RAM
1.44 GB Active RAM
190 MB Inactive RAM
558 MB Wired RAM
303 MB Page-ins
0 B Page-outs -
Populating a dynamic array with objects and managing it in runtime.
So I'm another stuck firstyear. I'll try and make my question compact. I'm using Flash CS6 and have drawn an animated character on the stage that consists of separate parts that are animated and its head is a separate class/symbol entirely because it has not only animation, but a state switch timeline as well. This said Head extends the Main that is the character MovieClip.
I am using a dynamic array to store and .push and .splice objects of another class that would collide with this said Head.
I also discovered the super() function that is implicitly called as the constructor of the parent in any child class that extends the parent, in this case Head extends Main. The issue is that my collidable object array is populated within the main, within the function that spawns every next collidable object with a TimerEvent. This said function then gets called twice due to the super() call.
I have tried putting this super() call into an impossible statement in my child class, but it doesn't change a thing, and it was said that this method is unsafe so I don't even know if it should be working.
However what confuses me the most is when I trace() the .length of my collidable object array at the end of that function. As I said earlier, the original function both spawns an object after a period of Timer(1000) and adds it to the stage as well as adds the object onto the object array, but the super() constructor only duplicates the length call and a creates a copy of the object on the stage, but it does not add the second copy of the object onto the array. The trace() output goes on like so:
1
1
2
2
3
3
4
4
etc.
I wonder why and I'm really stumped by this.
Here is the code in question:
public class Main extends MovieClip {
public var nicesnowflake: fallingsnow;
var nicesnowflakespawntimer: Timer = new Timer(1000);
public var nicesnowflakearray: Array = new Array();
public function Main() {
nicesnowflakespawntimer.addEventListener(TimerEvent.TIMER, nicesnowflakespawn);
nicesnowflakespawntimer.start();
public function nicesnowflakespawn(event:TimerEvent) : void {
nicesnowflake = new fallingsnow;
nicesnowflake.x = Math.random()* stage.stageWidth;
nicesnowflake.y = - stage.stageHeight + 100;
nicesnowflakearray.push(nicesnowflake);
stage.addChild(nicesnowflake);
trace(nicesnowflakearray.length);
for (var i:Number = 0; i < nicesnowflakearray.length; i++){
nicesnowflakearray[i].addEventListener(Event.ENTER_FRAME, snowhit);
public function snowhit(event:Event) : void {
if (nicesnowflakearray[0].y >= 460){
if (nicesnowflakearray[0].y == stage.stageHeight) {
nicesnowflakearray.splice(nicesnowflakearray.indexOf(nicesnowflake), 1);
//if (this.hitTestObject(nicesnowflake)){
//trace("hit");
I am also fiddling with the collision, but I believe that it would sort itself out when I deal with the array pop and depop properly. However I'm pasting it anyway in case the issue is subtly hidden somewhere I'm not looking for it. And here is the child class:
public class Head extends Main {
public function Head(){
if (false){
super();
this.stop();
So like what happens at the moment is that the array gets populated by the first object that spawns, but there is two objects on the stage, then when the objects reach stage.460y mark the array splices() the one object away and displays an error:
"#1010: A term is undefined and has no properties.
at Main/snowhit()"
then when the next object spawns, it repeats the process. Why does it trace the array.length as "1, 1, 2, 2, 3, 3, 4, 4, 5, 5, etc" until the despawn point and then goes on to display an error and then starts from 1 again, because if the array length is more than one object at the time when the first object of the array gets spliced away, shouldn't it go on as usual, since there are other objects in the array?
Thank you very much to whomever will read this through.There are multiple problems:
1. You should add eventlisteners for your objects only once, but you add eventlisteners every time your timer runs to all of your snowflakes, again and again:
for (var i:Number = 0; i < nicesnowflakearray.length; i++){
nicesnowflakearray[i].addEventListener(Event.ENTER_FRAME, snowhit);
change it to
nicesnowflake.addEventListener(Event.ENTER_FRAME, snowhit);
I don`t see why its even necessary to employ this snowflakearray, it would be much straight forward if you simply let the snowflakes take care of themselves.
2. Then you have to change your enterframe function accordingly
public function snowhit(event:Event) : void {
if (e.currentTarget.y >= 460){
if (e.currentTarget.y == stage.stageHeight) {
e.currentTarget.removeEventlistener(Event.ENTER_FRAME, snowhit);
removeChild(e.currentTarget);
3.
//if (this.hitTestObject(nicesnowflake)){
//trace("hit");
since "this" is a reference to the Main class (root) it surely won`t function as you intend it to.
if (false){
super();
makes no sense to use a condition that can never be true -
Sharing internet connection with powerbook and nintendo wii through airport
i have been trying to share my internet connection from my imac to my powerbook and nintendo wii. i've been unable to accomplish neither. i've opened the sharing preferences, chosen "share your connection from built in ethernet" which is how my imac is connected to the internet, and then chosen "to computers using airport". if i then set my airport options to automatic channel, encryption using 40 bit wep and set a 5 character password as it says if you "plan to share your internet connection with non-apple computers", (and then turn internet sharing on) shouldn't i be able to connect either/both my powerbook and my nintendo wii? or is it necessary to have some other piece of hardware or go through some other steps?
thanks in advance for any help.I got a macbook for college and I had the same problem with connecting my Wii to the macbook's connection. But lo and behold, the internet's a wonderful place! I tried this out (http://www.macosxhints.com/article.php?story=20070514152251515) and it worked! I'm not sure about the powerbook bit though, sorry. Hope it works for you too.
-
Strange behavior with Zoom and Image control
HELP - I have a strange behavior (bug?) with using Zoom
effect on an Image that has been placed on a Canvas. I am using
dynamically instantiated images which are placed on a canvas inside
a panel. I then assign a Zoom IN and Zoom Out behavior to the
image, triggered by ROLL_OVER and ROLL_OUT effect triggers. THE BUG
is that the image jumps around on the Zoom OUT and lands on a
random place on the canvas instead of coming back to the original
spot. This is especially true if the mouse goes in and out of the
image very quickly. HELP -- what am I doing wrong? Computer = Mac
OS X 10.4.9 Flex 2.0.1
Here's a simple demo of the bug -- be sure to move the mouse
in and out rapidly:
<?xml version="1.0" encoding="utf-8"?>
<mx:Application xmlns:mx="
http://www.adobe.com/2006/mxml"
layout="absolute" creationComplete="setUp();">
<mx:Script><![CDATA[
import mx.events.EffectEvent;
import mx.effects.Fade;
import mx.effects.Zoom;
import mx.rpc.events.ResultEvent;
import flash.display.Sprite;
import mx.core.UIComponent;
import mx.controls.Image;
private var zoomIn:Zoom;
private var zoomOut:Zoom;
private function setUp():void {
var image:Image = new Image();
image.id = "album_1_1";
image.x = 200;
image.y = 200;
image.width = 64;
image.height = 64;
image.source = "
http://s3.amazonaws.com/davidmccallie/album-128.jpg";
image.addEventListener(MouseEvent.ROLL_OVER, doZoom);
image.addEventListener(MouseEvent.ROLL_OUT, doZoom);
myCanvas.addChild(image);
zoomIn = new Zoom();
zoomIn.zoomHeightTo = 2.0;
zoomIn.zoomWidthTo = 2.0;
zoomIn.captureRollEvents = true;
zoomIn.suspendBackgroundProcessing = true;
zoomOut = new Zoom();
zoomOut.zoomHeightTo = 1.0;
zoomOut.zoomWidthTo = 1.0;
zoomOut.captureRollEvents = true;
zoomOut.suspendBackgroundProcessing = true;
private function doZoom(event:MouseEvent):void {
var image:Image = Image(event.currentTarget);
if (event.type == MouseEvent.ROLL_OVER) {
zoomIn.target = event.currentTarget;
zoomIn.play();
} else if (event.type == MouseEvent.ROLL_OUT) {
zoomOut.target = event.currentTarget;
zoomOut.play();
]]>
</mx:Script>
<mx:Panel width="100%" height="100%"
layout="absolute">
<mx:Canvas id="myCanvas" width="100%" height="100%">
</mx:Canvas>
</mx:Panel>
</mx:Application>There must be bugs in the Zoom effect code -- I changed the
Zoom to Resize in the above code, and it works perfectly. Of
course, Resize is not as nice as Zoom because you can't set the
resize to be around the center of the image, but at least it works.
Does anyone know about bugs in the Zoom effect? -
Windows Explorer keeps crashing under Win 7 with RH7 and Source Control installed
This is an "informational" thread in case someone experiences the same problems. We installed RH7 on Windows 7 32-bit and accidentally, Robo Source Control was installed, too, although we do not use it. The latter loads three extensions into the shell that caused the Windows Explorer to crash on a regular basis ("Windows Explorer has stopped working"). After deinstallation of Robo Source, the problem seems to be resolved.
I would like to tell you that this problem is an issue with RH8, as well.
-
RDGateway CAP with MFA and still control device redirection by group
We currently use multiple RD Gateways with Local Connection Authorization Policies (CAP) to control what groups of users have drive, clipboard, and Printer redirection enabled/disabled.
We are looking at implementing Multi Factor authentication (MFA), but all the solutions we have found and tested remove our ability to control what groups of users have the device redirection. Are there any ways to implement MFA and still be able to
enable or disable device redirection based on user and/or group membership?Hi James,
Thank you for posting in Windows Server Forum.
As per my knowledge, we can implement RD Gateway MFA under windows Azure. Apart sorry to say but I don’t found any related scenario for your case as it get implemented until now for redirection.
You can refer below article for reference.
Step By Step – Using Windows Server 2012 R2 RD Gateway with Azure Multifactor Authentication
Thanks for your understanding and Support!
Regards.
Dharmesh Solanki
TechNet Community Support
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected] -
Sorry, I'm new to BC and need to establish the best way to obtain and use new email addresses for my client. The site is created in Adobe Muse and I wish to host it with BC. THANK YOU!
You need to be on an upgraded BC plan to at least a webMarketing plan to be able to set up email with it. I don't recommend the BC email anyways. Here is a blog article I wrote some time ago on getting around the BC email limitations.
-
Problem with freezing and volume control PLZ HELP
every time i go into my volme and ringtones and blackberry messenger settings and it just freezes and the only solution is to take out the battery,
i can not get my volume changed or turned of my company that i deal with is telus i have no volume on my phone what so ever
-
Can I make a Mobile site with Muse and then go through PhoneGap?
I would like to use Muse to design a mobile site then use phone gap build to package it as an app. Is this possible? I was thinking I could export as HTML and then use those files or even move those to dreamweaver then to phone gap...
Thanks in advance for any ideas/help.I tried building an App through PhoneGap, but I keep getting a error when I try to create it for IOS. It asks me for a key? Do I have to be an Apple Developer to create an App for IOS. I don't necessarily want my App going through the App Store, I just want my mobile site to prompt the visitor to click on a button to download the App to their home screen.
Thanks.
Maybe you are looking for
-
I can't select split document option with CS6
Hi. I have Indesign CS5.5 on PC but I have been working on a document with the trial of CS6. I have set a table of contents (in the user interface, not in the book pages.) I'm all set to export the document. In CS5.5 i have the option to tick the box
-
Some of my Tiger rename scripts aren't working correctly in Leopard. I have a scripts that sequentially renames files 1, 2, 3, 4, 5, 6..... In Leopard (null) always gets added to the resulting filename so I get (null)1, (null)2 etc etc...... Anyone a
-
SL and iTunes broken iPhone sync
I get this message when I plug my iPhone into the cradle: "The Phone [my phone's name] cannot be synced. You do not have enough access privileges for this operation." It still manages to sync most of the info, including podcasts and music. I cannot t
-
Hi, Does the business graphic UI support any events on the displayed data ? (for example: selecting a column and perform something...) Thanks, Nir.
-
Explain for some really email about SAP BW
Hello Gurus, I have following info from a email: subject : 'Data Push from BW Successful' ZBPUR_DNC_DATA_PUSH ended without errors. Audit Table: Table name Start time End time # of rows Incr Star