ASA 5505 Anyconnect VPN Users can't access Internet
Vpn user cannot access the internet but able to ping the lan network (192.168.1.0).. it seem like im missing a lan or nat rule.. Possibly allowing the vpn subnet 192.168.2.0 /24 to pass through to the internet. Im looking to accomplish this without split tunneling.. Thanks
on 8.2.5 version or lower: Let say your inside hosts are accessing Internet by using dynamic nat index "1" and now you can use the same nat index "1" allow your vpn-pool range to be part of the same dynamic-nat index "1" to access the Internet. Note I am natting source interface is be outside for vpn-client users because they (vpn-users) are physically coming off the outside interface.
nat (outside) 1 192.168.2.0 255.255.255.0
on 8.3 version or greater:
object network vpn-user-subnet
subnet 192.168.2.0 255.255.255.0
nat (outside,outside) dynamic interface
Hope this helps.
Thanks
Rizwan Rafeek
Similar Messages
-
ASA 5505 AnyConnect VPN Can RDP to clients but can't ping/icmp
Hello all,
I've been searching all day for a solution to this problem. I setup and SSL anyconnect VPN on my Cisco ASA 5505. It works well and connects with out a problem. However, I can't ping any internal clients, but I can RDP to them. It may be something simple and I would appreciate any help. Most of the time people end up posting their config so I will as well.
MafSecASA# show run
: Saved
ASA Version 8.2(1)
hostname MafSecASA
domain-name mafsec.com
names
interface Vlan1
nameif inside
security-level 100
ip address 10.4.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 7.3.3.2 255.255.255.248
interface Vlan3
no forward interface Vlan1
nameif dmz
security-level 50
ip address 172.20.1.1 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
speed 100
duplex full
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
switchport access vlan 3
ftp mode passive
clock timezone EST -5
clock summer-time EDT recurring
dns server-group DefaultDNS
domain-name mafsec.com
same-security-traffic permit intra-interface
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object tcp
protocol-object udp
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_2
protocol-object ip
protocol-object udp
protocol-object tcp
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_3
protocol-object ip
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_4
protocol-object ip
protocol-object icmp
access-list inside_access_in extended permit icmp any any
access-list inside_access_in extended permit ip any any
access-list inside_access_in remark allow remote users to internal users
access-list inside_access_in remark allow remote users to internal users
access-list inside_access_in extended permit object-group DM_INLINE_PROTOCOL_4 10.4.0.0 255.255.255.0 10.5.0.0 255.255.255.0
access-list inside_access_in extended permit object-group DM_INLINE_PROTOCOL_3 10.5.0.0 255.255.255.0 10.4.0.0 255.255.255.0
access-list outside_access_in extended permit icmp any any
access-list inside_split_tunnel standard permit 10.4.0.0 255.255.255.0
access-list inside_split_tunnel standard permit 10.5.0.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 10.4.0.0 255.255.255.0 10.4.0.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 10.4.0.0 255.255.255.0 10.5.0.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 10.5.0.0 255.255.255.0 10.4.0.0 255.255.255.0
access-list inside_nat0_outbound_1 extended permit ip 10.4.0.0 255.255.255.0 10.4.0.0 255.255.255.0
access-list inside_nat0_outbound_1 extended permit ip 10.4.0.0 255.255.255.0 10.5.0.0 255.255.255.0
access-list inside_nat0_outbound_1 extended permit ip 10.5.0.0 255.255.255.0 10.4.0.0 255.255.255.0
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu dmz 1500
ip local pool SSLVPNPool2 10.5.0.1-10.5.0.254 mask 255.255.255.0
ip verify reverse-path interface outside
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
icmp permit any outside
no asdm history enable
arp timeout 14400
nat-control
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound_1
nat (inside) 1 0.0.0.0 0.0.0.0
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 7.3.3.6 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication enable console LOCAL
aaa authentication ssh console LOCAL
http server enable
http 10.4.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 5
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 10
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 10.4.0.0 255.255.255.0 inside
ssh timeout 5
ssh version 2
console timeout 0
dhcpd option 6 ip 8.8.8.8 8.8.4.4
dhcpd address 10.4.0.15-10.4.0.245 inside
dhcpd dns 8.8.8.8 8.8.4.4 interface inside
dhcpd lease 86400 interface inside
dhcpd option 3 ip 10.4.0.1 interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
enable outside
svc image disk0:/anyconnect-win-2.5.3055-k9.pkg 1
svc image disk0:/anyconnect-macosx-i386-2.5.3055-k9.pkg 2
svc enable
tunnel-group-list enable
group-policy SSLVPN internal
group-policy SSLVPN attributes
dns-server value 8.8.8.8 8.8.4.4
vpn-tunnel-protocol svc
group-lock none
split-tunnel-policy tunnelspecified
split-tunnel-network-list value inside_split_tunnel
vlan none
address-pools value SSLVPNPool2
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
username user1 password
username user1 attributes
service-type remote-access
username user2 password
tunnel-group SSLVPNGROUP type remote-access
tunnel-group SSLVPNGROUP general-attributes
address-pool SSLVPNPool2
default-group-policy SSLVPN
tunnel-group SSLVPNGROUP webvpn-attributes
group-alias SSLVPN enable
prompt hostname context
Cryptochecksum:3b16cbc9bbdfa20e6987857c1916a396
: end
Thank in advance for any help!Your config actually looks good (you have the ACL that would allow the echo-reply back since you don't have inspection turned on) - are you sure this isn't a windows firewall issue on the PCs? I'd try pinging a router or switch just to make sure.
--Jason -
Unable to ping device behind Cisco 3750 on the same inside VLAN via Cisco ASA 5505 Anyconnect VPN
Hi Guys,
I've been stuck with this for the last 2 days, and I thought to try and use Cisco's forum, I setup my home DC, and started having problems once I moved a Cisco 5505 behind a Cisco 1841 router (I wanted to eventually test DMVPN live on the internet,) I was no longer able to ping some devices, then as soon as I introduce a collapsed core/distribution switch, I'm also no longer able to ping the devices behind the Cisco 3750, I've attached a network diagram and the ASA running-config.
Everything seem fine internally with the exception of an intermittent network connectivity with a Citrix NetScaler VPX running on a VMware ESXi.
For some odd reason, I am able to ping the following, with no issues.
Cisco 3750 SVI (192.168.1.3)
CentOS web server (connected directly to the Cisco ASA 5505)
I have checked and enable the following:
Nat Exemption
Sysopt connection permit-vpn
ACL's
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
Added ICMP in the inspection policy
Packet-capture - Only getting echo requests.
Thanks in advance!Hi,
I believe you have the problem with your no-nat configurations..... you to exempt NAT for the traffic from 172.16.10.0 (Anyconnect VPN pool) to 192.168.1.0/24 (Inside LAN) to make this work
object network acvpnpool
subnet <anyconnect VPN Subnet>
object network insidelan
subnet <inside lan subnet>
nat (inside,outside) source static acvpnpool acvpnpool destination static insidelan insidelan
Make sure that you are able to reach the GW/Inside ip adress of the firewall from LAN machine.... all routing in place properly..... Thanks!!!
Regards
Karthik -
2nd user can't access internet
I set up a 2nd user account on my Mac and I can't access the internet from it. I've checked my Network settings and it says everything is working normal.
These were written for Yosemite, but apply to 10.6 also.
Internet – can’t connect - Yosemite
Internet – can’t connect - Yosemite (2) -
My default user can't access internet
when I tried to use the internet from my default user account, it refused to connect, but my secondary user has no issues. how do i fix my default account?
These were written for Yosemite, but apply to 10.6 also.
Internet – can’t connect - Yosemite
Internet – can’t connect - Yosemite (2) -
Asa 5505 Remote VPN Can't access with my local network
Hello Guys ,, i have a problem with my asa 5505 Remote VPN Connection with local network access , the VPn is working fine and connected , but the problem is i can't reach my inside network connection of 192.168.30.x , here is my configuration , please can you help me
ASA Version 8.2(1)
interface Vlan1
nameif inside
security-level 100
ip address 192.168.30.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 155.155.155.10 255.255.255.0
interface Vlan5
no nameif
no security-level
no ip address
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
access-list inside_nat0_outbound extended permit ip any 192.168.100.0 255.255.255.240
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool vpn-Pool 192.168.100.1-192.168.100.10 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy mull internal
group-policy mull attributes
vpn-tunnel-protocol IPSec
username xxx password eKJj9owsQwAIk6Cw encrypted privilege 0
vpn-group-policy Mull
tunnel-group mull type remote-access
tunnel-group mull general-attributes
address-pool vpn-Pool
default-group-policy mull
tunnel-group mull ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname contextHey Jennifer i did every thing you mention it , but still i can't reach my inside network (LOCAL network) iam using Shrew Soft VPN Access Manager for my vpn connection
here is my cry ipsec sa
interface: outside
Crypto map tag: SYSTEM_DEFAULT_CRYPTO_MAP, seq num: 65535, local addr: 155.155.155.1
local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
remote ident (addr/mask/prot/port): (192.168.100.1/255.255.255.255/0/0)
current_peer:155.155.155.1, username: Thomas
dynamic allocated peer ip: 192.168.100.1
#pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
#pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: 155.155.155.1/4500, remote crypto endpt.: 155.155.155.20/4500
path mtu 1500, ipsec overhead 82, media mtu 1500
current outbound spi: 73FFAB96
inbound esp sas:
spi: 0x1B5FFBF1 (459275249)
transform: esp-aes esp-sha-hmac no compression
in use settings ={RA, Tunnel, NAT-T-Encaps, }
slot: 0, conn_id: 12288, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
sa timing: remaining key lifetime (sec): 2894
IV size: 16 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001
outbound esp sas:
spi: 0x73FFAB96 (1946135446)
transform: esp-aes esp-sha-hmac no compression
in use settings ={RA, Tunnel, NAT-T-Encaps, }
slot: 0, conn_id: 12288, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
sa timing: remaining key lifetime (sec): 2873
IV size: 16 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001 -
VPN users unable to access internal network - ASA 8.3.1
Hello,
I have a base config of AnyConnect VPN below, however the ASA 8.3.1 code has deprecated some commands and the VPN/NAT/FW rule syntax is quite different. Can someone point out what's missing from the pertinent config below that prevents the VPN Pool from accessing the internal LAN?
The Core LAN router is 1.2.3.1.
ASA Version 8.3(1)
interface Ethernet0/0
nameif inside
security-level 100
ip address 1.2.3.2 255.255.255.0
ip local pool anyconnect-vpn-pool 1.2.9.10-1.2.9.20 mask 255.255.255.0
object network DataVLAN
subnet 1.2.3.0 255.255.255.0
object-group network Internal-Data
network-object object DataVLAN
nat (any,any) after-auto source dynamic Internal-Data Outside_INT
route inside 1.2.0.0 255.255.0.0 1.2.3.1 1
dynamic-access-policy-record DfltAccessPolicy
webvpn
enable outside
svc image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
svc enable
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
address-pools value anyconnect-vpn-pool
group-policy GroupPolicy1 internal
group-policy GroupPolicy1 attributes
address-pools value anyconnect-vpn-pool
group-policy vpn-anyconnecct-policy internal
group-policy vpn-anyconnecct-policy attributes
vpn-tunnel-protocol svc webvpn
webvpn
url-list none
svc ask enable
tunnel-group vpn-users type remote-access
tunnel-group vpn-users general-attributes
address-pool anyconnect-vpn-pool
default-group-policy vpn-anyconnecct-policy
tunnel-group anyconnect2 type remote-access
tunnel-group anyconnect2 general-attributes
address-pool anyconnect-vpn-pool
TIA.
MikeHi Rohan,
Are you saying to replace "nat (any,any)" with "nat (inside,outside)"? I was wondering about this because I'd always done "nat (inside,outside)" but a colleague had performed the initial configuration which already contained "nat (any,any)" statement and I was not sure if this was just something new in 8.3.1. I also noticed the "global" command is no longer available.
I will give this a try. Thanks.
-Mike -
Cisco ASA 5505 Ipsec VPN and random connection dropping issues.
Hello,
We are currently having issues with a ASA 5505 Ipsec VPN. It was configured about 7-8 months ago and has been running very well..up until the last few weeks. For some reason, the VPN tends to randomly disconnect any user clients connected a lot. Furthermore, sometimes it actually connects; however does not put us on the local network for some reason and unable to browse file server. We have tried rebooting the ASA a few times and our ISP Time Warner informed us there are no signs of packet loss but still unable to pinpoint the problem. Sometimes users close out of VPN client completely, reopen several times and then it works. However it's never really consistent enough and hasn't been the last few weeks. No configuration changes have been made to ASA at all. Furthermore, the Cisco Ipsec VPN client version is: 5.0.70
Directly below is our current running config (modded for public). Any help or ideas would be greatly appreciated. Otherwise, if everything looks good...then I will defer back to our ISP Time Warner:
: Saved
ASA Version 8.4(2)
hostname domainasa
domain-name adomain.local
enable password cTfsR84pqF5Xohw. encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 205.101.1.240 255.255.255.248
ftp mode passive
clock timezone EST -5
clock summer-time EDT recurring
dns domain-lookup inside
dns domain-lookup outside
dns server-group DefaultDNS
name-server 192.168.2.60
domain-name adomain.local
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network SBS_2011
host 192.168.2.60
object network NETWORK_OBJ_192.168.2.0_24
subnet 192.168.2.0 255.255.255.0
object network NETWORK_OBJ_192.168.5.192_
27
subnet 192.168.5.192 255.255.255.224
object network Https_Access
host 192.168.2.90
description Spam Hero
object-group network DM_INLINE_NETWORK_1
network-object object SPAM1
network-object object SPAM2
network-object object SPAM3
network-object object SPAM4
network-object object SPAM5
network-object object SPAM6
network-object object SPAM7
network-object object SPAM8
object-group service RDP tcp
description Microsoft RDP
port-object eq 3389
access-list outside_access_in extended permit tcp object-group DM_INLINE_NETWORK_1 object SBS_2011 eq smtp
access-list outside_access_in extended permit tcp any object SBS_2011 eq https
access-list outside_access_in extended permit icmp any interface outside
access-list outside_access_in remark External RDP Access
access-list outside_access_in extended permit tcp any object SBS_2011 object-group RDP
access-list domain_splitTunnelAcl standard permit 192.168.2.0 255.255.255.0
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool test 192.168.10.1-192.168.10.5 mask 255.255.255.0
ip local pool VPN_Users 192.168.5.194-192.168.5.22
0 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source static NETWORK_OBJ_192.168.2.0_24
NETWORK_OBJ_192.168.2.0_24
destination static NETWORK_OBJ_192.168.5.192_
27 NETWORK_OBJ_192.168.5.192_
27 no-proxy-arp route-lookup
object network obj_any
nat (inside,outside) dynamic interface
object network SBS_2011
nat (inside,outside) static interface service tcp smtp smtp
object network Https_Access
nat (inside,outside) static interface service tcp https https
nat (inside,outside) after-auto source dynamic any interface
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 205.101.1.239 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-reco
rd DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 192.168.2.0 255.255.255.0 inside
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 192.168.2.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.160-192.168.2.19
9 inside
dhcpd dns 192.168.2.60 24.29.99.36 interface inside
dhcpd wins 192.168.2.60 24.29.99.36 interface inside
dhcpd domain adomain interface inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy domain internal
group-policy domain attributes
wins-server value 192.168.2.60
dns-server value 192.168.2.60
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value domain_splitTunnelAcl
default-domain value adomain.local
username ben password zWCAaitV3CB.GA87 encrypted privilege 0
username ben attributes
vpn-group-policy domain
username sdomain password FATqd4I1ZoqyQ/MN encrypted
username sdomain attributes
vpn-group-policy domain
username adomain password V5.hvhZU4S8NwGg/ encrypted
username adomain attributes
vpn-group-policy domain
service-type admin
username jdomain password uODal3Mlensb8d.t encrypted privilege 0
username jdomain attributes
vpn-group-policy domain
service-type admin
tunnel-group domain type remote-access
tunnel-group domain general-attributes
address-pool VPN_Users
default-group-policy domain
tunnel-group domain ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:e2466a5b754
eebcdb0cef
f051bef91d
9
: end
no asdm history enable
Thanks againHello Belnet,
What do the logs show from the ASA.
Can you post them ??
Any other question..Sure..Just remember to rate all of the community answers.
Julio -
Other user can't access to OBIEE 11G installed on a server
Hello,
We have installed OBIEE 11G on a server ( windows sever 2008 r2) with admin account, and it works fine, But others users can't access to obiee 11g ( administration icons are white in their sessions) even they have admin rights.
Can anyone tell me what should we do??
Thank you.Hi,
This is the exact format how my tnsnames.ora file looks. sorry, I can ping it in command prompt now. In my connection pool i tried first DSN = ab.bc.xy.zx, did not work. Then I saw oracle's default repository and changed my DSN to your suggested format starting from "DESCRPTION" to rest. Still no luck Do you think, i should put the same TNS in my local machine??
ab.bc.xy.zx =
(DESCRIPTION =
#(ADDRESS = (PROTOCOL = TCP)(HOST = 10.20.30.110)(PORT = 1521))
#(ADDRESS = (PROTOCOL = TCP)(HOST = 10.20.30.120)(PORT = 1521))
(ADDRESS = (PROTOCOL = TCP)(HOST = 10.20.30.130)(PORT = 1521))
(LOAD_BALANCE = yes)
(CONNECT_DATA =
(SERVER = DEDICATED)
(SID = cap2)
thanks,
BK. -
Saving so that windows user can have access?
I have my project all ready and those with quick time...loads up perfectly. However those who have windows have a long wait or pile will not come up. Do you know how i can save my final cut express project so that window users can have access to it?
thank you. one last question....the quick time movie file can not be seen when opening on a windows. do you know if i need a quick time pro so that i can convert it? or is there a way that i don't know about?
-
Why the apple store is so expensive and why the apple users can't access for free after spending huge amount in apple phone ?
The Apple store is correct. The warranty is not international, and Apple will not accept or return iPhones shipped from a different country. You need to ship the phone to somebody in Hong Kong who can take it in to Apple for repair, or pay a third party repair shop in the Philippines to fix it.
-
Just bought new Ipod Touch 5g. I found out it can't access Internet in home network. not really cannot access, but very slow to open any web page, App Store failed to access, etc. But, OK with other Wifi (office & starbucks). Others existing iOS devices (Iphone4 & Ipad2) have no problem like this. I'm using Linksys E4200 router at home. anyone has any idea why?
Try:
- Reset the iPod. Nothing will be lost
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on the router
- Reset network settings: Settings>GeneralReset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- iOS: Recommended settings for Wi-Fi routers and access points
- Restore from backup
- Restore to factory settings/new iPod.
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar -
IPhone 5s can connect to wireless WIFI router but can not access internet.
iPhone 5s can connect to wireless WIFI router but can not access internet at work. The admin says the router lets my iPhone connect to LAN, but the iPhone does not have server IP to access the internet. I entered the server IP and port number in the HTTP PROXY fields but I still can not access the web. Any ideas?
TIA
RichYou IT person should be able to sort this out. But, they seems to be too busy or disinterested to do this. Suggest you provide the it person with an iPhone to get interested.
Any could be lots of things.
The best you can do is to get access to the admin setup for networking on a pc? The internet settings are all the same. Only what names the manufactures change from OS to OS. Check and compare parameters.
Phone works to internet at home, I assume? -
Can not access internet via wired connection, wireless working OK
Background information,Came home from vacation turned on PC to access email.Emails started downloading then stoped,started getting messages that firefox stopped working and Thunderbird quit working and others.My desktop is attached to a verizon router.all my other devices are wireless and are working fine through the same router.I connected my laptop to the lan connection, turned off wifi and accessed the internet via lan connection.Using device manager, checked drivers, says up to date, also says that it is working properly.I have gone to the command line and can ping google.com.I can ping the loop around. ping127.0.0.1I have done the ipconfig/release,ipconfig/renew, and ipconfig/flushdnsipconfig/all indcates that it is there and enabledMy Lan connection is part of the mother board.can not access internet via wiredconnection.Not sure what to do next.Help Please
Reply: I spent about an hour last night doing all the things that you suggested including moving the lan cable from my desktop to my laptop which worked fine. When I hoover over the connection it says; Network3 Internet Access no error messages.When I unplug the cable at the router a red x covers that connection icon.Plug it back in red x goes away.It is seeing the router, just does not appear to be providing selected web page info.Computer thinks it is working fine.
-
Everything works perfect with Macs, iPhone, iPads but I have 2 pcs that now can't access internet. The PCs connect to the airport and my other access points but no internet- The PCs sent an error of DNS
Yes, as we already said, it will do all of this if you have a good wireless signal reaching the bedroom.
Remember that an extender or repeater or whatever you want to call it can only extend the quality of signal that it receives.
The Ethernet signal that the Express delivers will only be as good as the quality of the wireless connection between the AirPort Extreme and AirPort Express.
If you have doubts, make sure that you understand the store's return policy before you buy.
Maybe you are looking for
-
The cursor on my intel 64 bit macbook pro won't click on anything. I boot it up and can log into my account and move the cursor around just fine along with multitouch gestures working fine too. hovering over items on the dock even makes the program n
-
When exporting my indesign file to an interactive pdf i get the following problem: I open the pdf, when there is flash content , i can set the properties for it to be visible when the page is opened, that is what i want. When i then save the pdf othe
-
Why the metadata created with EM can't be found in JDeveloper
I created some dimensions and measures. then put them in a cube.And I created a measure folder and added the measures . I do all the task with EM. And when I use JDeveloper to build a crosstable, only the demo measures and dimensions are in the avail
-
Hi, I just downloaded IOS 8 on my iPhone 4S. Can't restore my settings nor synchronise anymore. Any helpful advice ?
-
hi guyz, i have a field total_amount when iam putting in my text node it saying total_amount is unknown in the form...where as all other fields in the textnode works. total_amount is currency field.. plz advice regards