ATA 186 status
Hi,
How is it possible to check the status of ATA 186?
Is it registered with a SIP server?
Is there an active conversation?
Which phone port is in use?
What codec is being used?
What is the current packet rate/bandwidth consumption for a call?
How to check for possible system issues/errors?
Does ATA 186 have a command line interface?
Thanks.
Alex
Hi
Cisco ATA 186 has an IVR which can be accessed through your phone.
http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_configuration_example09186a00800c3a50.shtml
Once the IP address is set through IVR, the device can be accessed through "http:///dev"
Pls rate the helpful posts.
Regards
JD
Similar Messages
-
hi, i have a problem with ATA 186
when I light on the ATA it work very well after a certain moment the calls doesn't pass anymore Im forced to reboot every time when this problem happend
thanksIS this CCM? If so please report to IP telephony forum where there are many fellows that can help.
If it is CCME I would start looking at the status of the ephone, and try to ping the ATA when it freezes. -
How do I/Do I need to fix "ata#.00 status { DRDY }" error?
I've got an old server that used to be running windows that I have received to set up with linux for myself. As I was working with it, I remembered that I had an old computer that I was just going to trash/give away anyways, of which many components would be better. I have since set up a computer that's a mash of components between the two and everything seems to run perfectly except for one problem: I keep getting this error: (Where "#" is either 2, 3, or 4)
ata#.00: exception Emask 0x50 SAct 0x0 SErr 0x48900 action 0x6 frozen
ata#: SError: {UnrecovData HostInt 10B8B Handshk }
ata#.00: failed command WRITE DMA
ata#.00: cmd ca/00:88:9f:ca:8d/00:00:00:00:00/e8 tag 0 dma 69632 out
res 50/00:88:9f:ca:8d/00:00:9e:c9:8d/e8 Emask 0x50 (AtA bus error)
ata#.00: status: { DRDY }
This error occurred once for each of the three numbers (which also happens to correspond to the three sata ports my HDs are plugged into): 2 and 3 while I was using dd to zero them (I zeroed all three but 4 didn't give any errors), and 4 just after installing grub onto a mirror raid composing of HDs 2 and 3.
All of the HDs originally used IDE so I used a converted to switch them (Model number CB-IS100)
Additionally, when deconstructing the computers, one of the sata cables tore the first female connector out of the motherboard (hence why they start at 2), but while I know that's not preferable, I don't think it would cause this error.
Finally, this motherboard was in a computer that had, as far as I could tell, a poor power supply that cause it to reboot when using a lot of CPU power.
My question is really this: Will this cause any major problems or can I ignore it? Also, is there anything I can do to fix it?
This is my dmesg:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.11.6-1-ARCH (nobody@var-lib-archbuild-extra-i686-thomas) (gcc version 4.8.1 20130725 (prerelease) (GCC) ) #1 SMP PREEMPT Sat Oct 19 00:29:46 CEST 2013
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x00000000000987ff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000000098800-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000cfedf7ff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000cfedf800-0x00000000cfedffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000cfee0000-0x00000000cfee2fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000cfee3000-0x00000000cfeeffff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000cfef0000-0x00000000cfefffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f0000000-0x00000000f3ffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000ffffffff] reserved
[ 0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
[ 0.000000] SMBIOS 2.4 present.
[ 0.000000] DMI: HP Pavilion 061 ER879AA-ABA M7457C/EMERY, BIOS 3.15 06/23/2006
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0xcfedf max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-EFFFF uncachable
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 080000000 mask FC0000000 write-back
[ 0.000000] 2 base 0C0000000 mask FF0000000 write-back
[ 0.000000] 3 base 0CFF00000 mask FFFF00000 uncachable
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] found SMP MP-table at [mem 0x000f5f80-0x000f5f8f] mapped at [c00f5f80]
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] initial memory mapped: [mem 0x00000000-0x00bfffff]
[ 0.000000] Base memory trampoline at [c0094000] 94000 size 16384
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x37000000-0x373fffff]
[ 0.000000] [mem 0x37000000-0x373fffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x30000000-0x36ffffff]
[ 0.000000] [mem 0x30000000-0x36ffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x2fffffff]
[ 0.000000] [mem 0x00100000-0x003fffff] page 4k
[ 0.000000] [mem 0x00400000-0x2fffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x37400000-0x377fdfff]
[ 0.000000] [mem 0x37400000-0x377fdfff] page 4k
[ 0.000000] BRK [0x00877000, 0x00877fff] PGTABLE
[ 0.000000] RAMDISK: [mem 0x7ef2f000-0x7fffffff]
[ 0.000000] Allocated new RAMDISK: [mem 0x3672d000-0x377fddaf]
[ 0.000000] Move RAMDISK from [mem 0x7ef2f000-0x7ffffdaf] to [mem 0x3672d000-0x377fddaf]
[ 0.000000] ACPI: RSDP 000f82e0 00014 (v00 HP-CPC)
[ 0.000000] ACPI: RSDT cfee3040 00030 (v01 HP-CPC AWRDACPI 42302E31 AWRD 00000000)
[ 0.000000] ACPI: FACP cfee30c0 00074 (v01 HP-CPC AWRDACPI 42302E31 AWRD 00000000)
[ 0.000000] ACPI: DSDT cfee3180 0505D (v01 HP-CPC AWRDACPI 00001000 MSFT 0100000E)
[ 0.000000] ACPI: FACS cfee0000 00040
[ 0.000000] ACPI: MCFG cfee8340 0003C (v01 HP-CPC AWRDACPI 42302E31 AWRD 00000000)
[ 0.000000] ACPI: APIC cfee8240 00084 (v01 HP-CPC AWRDACPI 42302E31 AWRD 00000000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 2438MB HIGHMEM available.
[ 0.000000] 887MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 377fe000
[ 0.000000] low ram: 0 - 377fe000
[ 0.000000] BRK [0x00878000, 0x00878fff] PGTABLE
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] Normal [mem 0x01000000-0x377fdfff]
[ 0.000000] HighMem [mem 0x377fe000-0xcfedefff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x00097fff]
[ 0.000000] node 0: [mem 0x00100000-0xcfedefff]
[ 0.000000] On node 0 totalpages: 851574
[ 0.000000] free_area_init_node: node 0, pgdat c06d7740, node_mem_map f4d2d020
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3991 pages, LIFO batch:0
[ 0.000000] Normal zone: 1744 pages used for memmap
[ 0.000000] Normal zone: 223230 pages, LIFO batch:31
[ 0.000000] HighMem zone: 4878 pages used for memmap
[ 0.000000] HighMem zone: 624353 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] smpboot: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: [mem 0x00098000-0x00098fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x00099000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
[ 0.000000] e820: [mem 0xcff00000-0xefffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 14 pages/cpu @f4ce3000 s33536 r0 d23808 u57344
[ 0.000000] pcpu-alloc: s33536 r0 d23808 u57344 alloc=14*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 849798
[ 0.000000] Kernel command line: BOOT_IMAGE=boot/i686/vmlinuz archisobasedir=arch archisolabel=ARCH_201311 initrd=boot/i686/archiso.img
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] allocated 6813424 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Initializing HighMem for node 0 (000377fe:000cfedf)
[ 0.000000] Memory: 3346976K/3406296K available (4262K kernel code, 426K rwdata, 1356K rodata, 608K init, 948K bss, 59320K reserved, 2497412K highmem)
[ 0.000000] virtual kernel memory layout:
fixmap : 0xfff15000 - 0xfffff000 ( 936 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc06e9000 - 0xc0781000 ( 608 kB)
.data : 0xc0529d5e - 0xc06e8a00 (1787 kB)
.text : 0xc0100000 - 0xc0529d5e (4263 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: HWalign=128, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000] NR_IRQS:2304 nr_irqs:712 16
[ 0.000000] CPU 0 irqstacks, hard=f4008000 soft=f400a000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 3000.893 MHz processor
[ 0.003336] Calibrating delay loop (skipped), value calculated using timer frequency.. 6004.86 BogoMIPS (lpj=10002976)
[ 0.003342] pid_max: default: 32768 minimum: 301
[ 0.003402] Security Framework initialized
[ 0.003416] AppArmor: AppArmor disabled by boot time parameter
[ 0.003418] Yama: becoming mindful.
[ 0.003442] Mount-cache hash table entries: 512
[ 0.003753] Initializing cgroup subsys memory
[ 0.003767] Initializing cgroup subsys devices
[ 0.003771] Initializing cgroup subsys freezer
[ 0.003774] Initializing cgroup subsys net_cls
[ 0.006675] Initializing cgroup subsys blkio
[ 0.006723] CPU: Physical Processor ID: 0
[ 0.006727] CPU: Processor Core ID: 0
[ 0.006731] mce: CPU supports 4 MCE banks
[ 0.006745] CPU0: Thermal monitoring enabled (TM1)
[ 0.006763] Last level iTLB entries: 4KB 128, 2MB 128, 4MB 128
Last level dTLB entries: 4KB 64, 2MB 0, 4MB 64
tlb_flushall_shift: 6
[ 0.006919] Freeing SMP alternatives memory: 20K (c0781000 - c0786000)
[ 0.008197] ACPI: Core revision 20130517
[ 0.012076] ACPI: All ACPI Tables successfully acquired
[ 0.013370] ftrace: allocating 19099 entries in 38 pages
[ 0.023450] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.023843] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.057502] smpboot: CPU0: Intel(R) Pentium(R) D CPU 3.00GHz (fam: 0f, model: 06, stepping: 02)
[ 0.059999] Performance Events: Netburst events, Netburst P4/Xeon PMU driver.
[ 0.059999] ... version: 0
[ 0.059999] ... bit width: 40
[ 0.059999] ... generic registers: 18
[ 0.059999] ... value mask: 000000ffffffffff
[ 0.059999] ... max period: 0000007fffffffff
[ 0.059999] ... fixed-purpose events: 0
[ 0.059999] ... event mask: 000000000003ffff
[ 0.076727] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.083427] CPU 1 irqstacks, hard=f40ce000 soft=f40d8000
[ 0.006666] Initializing CPU#1
[ 0.083431] smpboot: Booting Node 0, Processors #1
[ 0.096604] Brought up 2 CPUs
[ 0.096610] smpboot: Total of 2 processors activated (12008.72 BogoMIPS)
[ 0.096819] devtmpfs: initialized
[ 0.096976] PM: Registering ACPI NVS region [mem 0xcfee0000-0xcfee2fff] (12288 bytes)
[ 0.100507] RTC time: 20:09:02, date: 05/19/14
[ 0.100577] NET: Registered protocol family 16
[ 0.100840] ACPI: bus type PCI registered
[ 0.100846] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.100944] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xf0000000-0xffffffff] (base 0xf0000000)
[ 0.100950] PCI: MMCONFIG at [mem 0xf0000000-0xffffffff] reserved in E820
[ 0.100954] PCI: MMCONFIG for 0000 [bus00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000) (size reduced!)
[ 0.100956] PCI: Using MMCONFIG for extended config space
[ 0.100959] PCI: Using configuration type 1 for base access
[ 0.102090] bio: create slab <bio-0> at 0
[ 0.102090] ACPI: Added _OSI(Module Device)
[ 0.102090] ACPI: Added _OSI(Processor Device)
[ 0.102090] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.102090] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.103853] ACPI: EC: Look up EC in DSDT
[ 0.110158] ACPI: Interpreter enabled
[ 0.110189] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130517/hwxface-571)
[ 0.110213] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.110217] ACPI: Using IOAPIC for interrupt routing
[ 0.110269] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.110379] ACPI: No dock devices found.
[ 0.118318] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.118328] acpi PNP0A08:00: ACPI _OSC support notification failed, disabling PCIe ASPM
[ 0.118332] acpi PNP0A08:00: Unable to request _OSC control (_OSC support mask: 0x08)
[ 0.118461] acpi PNP0A08:00: host bridge window [io 0x0000-0x0cf7] (ignored)
[ 0.118466] acpi PNP0A08:00: host bridge window [io 0x0d00-0xffff] (ignored)
[ 0.118470] acpi PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[ 0.118474] acpi PNP0A08:00: host bridge window [mem 0x000c0000-0x000dffff] (ignored)
[ 0.118478] acpi PNP0A08:00: host bridge window [mem 0xcff00000-0xfebfffff] (ignored)
[ 0.118481] PCI: root bus 00: using default resources
[ 0.118486] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[ 0.118696] PCI host bridge to bus 0000:00
[ 0.118703] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.118707] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.118710] pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
[ 0.118725] pci 0000:00:00.0: [8086:2770] type 00 class 0x060000
[ 0.118895] pci 0000:00:01.0: [8086:2771] type 01 class 0x060400
[ 0.118957] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.119125] pci 0000:00:1b.0: [8086:27d8] type 00 class 0x040300
[ 0.119148] pci 0000:00:1b.0: reg 0x10: [mem 0xfdff8000-0xfdffbfff 64bit]
[ 0.119231] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.119317] pci 0000:00:1b.0: System wakeup disabled by ACPI
[ 0.119384] pci 0000:00:1d.0: [8086:27c8] type 00 class 0x0c0300
[ 0.119433] pci 0000:00:1d.0: reg 0x20: [io 0xff00-0xff1f]
[ 0.119532] pci 0000:00:1d.0: System wakeup disabled by ACPI
[ 0.119597] pci 0000:00:1d.1: [8086:27c9] type 00 class 0x0c0300
[ 0.119646] pci 0000:00:1d.1: reg 0x20: [io 0xfe00-0xfe1f]
[ 0.119745] pci 0000:00:1d.1: System wakeup disabled by ACPI
[ 0.119808] pci 0000:00:1d.2: [8086:27ca] type 00 class 0x0c0300
[ 0.119857] pci 0000:00:1d.2: reg 0x20: [io 0xfd00-0xfd1f]
[ 0.119955] pci 0000:00:1d.2: System wakeup disabled by ACPI
[ 0.120030] pci 0000:00:1d.3: [8086:27cb] type 00 class 0x0c0300
[ 0.120079] pci 0000:00:1d.3: reg 0x20: [io 0xfc00-0xfc1f]
[ 0.120178] pci 0000:00:1d.3: System wakeup disabled by ACPI
[ 0.120251] pci 0000:00:1d.7: [8086:27cc] type 00 class 0x0c0320
[ 0.120273] pci 0000:00:1d.7: reg 0x10: [mem 0xfdfff000-0xfdfff3ff]
[ 0.120360] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.120440] pci 0000:00:1d.7: System wakeup disabled by ACPI
[ 0.120507] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
[ 0.120640] pci 0000:00:1e.0: System wakeup disabled by ACPI
[ 0.120712] pci 0000:00:1f.0: [8086:27b0] type 00 class 0x060100
[ 0.120948] pci 0000:00:1f.1: [8086:27df] type 00 class 0x01018a
[ 0.120966] pci 0000:00:1f.1: reg 0x10: [io 0x0000-0x0007]
[ 0.120978] pci 0000:00:1f.1: reg 0x14: [io 0x0000-0x0003]
[ 0.120990] pci 0000:00:1f.1: reg 0x18: [io 0x0000-0x0007]
[ 0.121002] pci 0000:00:1f.1: reg 0x1c: [io 0x0000-0x0003]
[ 0.121014] pci 0000:00:1f.1: reg 0x20: [io 0xfb00-0xfb0f]
[ 0.121164] pci 0000:00:1f.2: [8086:27c3] type 00 class 0x010400
[ 0.121185] pci 0000:00:1f.2: reg 0x10: [io 0xfa00-0xfa07]
[ 0.121196] pci 0000:00:1f.2: reg 0x14: [io 0xf900-0xf903]
[ 0.121206] pci 0000:00:1f.2: reg 0x18: [io 0xf800-0xf807]
[ 0.121217] pci 0000:00:1f.2: reg 0x1c: [io 0xf700-0xf703]
[ 0.121228] pci 0000:00:1f.2: reg 0x20: [io 0xf600-0xf60f]
[ 0.121238] pci 0000:00:1f.2: reg 0x24: [mem 0xfdffe000-0xfdffe3ff]
[ 0.121284] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.121418] pci 0000:00:1f.3: [8086:27da] type 00 class 0x0c0500
[ 0.121478] pci 0000:00:1f.3: reg 0x20: [io 0x0500-0x051f]
[ 0.121706] pci 0000:01:00.0: [10de:0a65] type 00 class 0x030000
[ 0.121722] pci 0000:01:00.0: reg 0x10: [mem 0xfb000000-0xfbffffff]
[ 0.121737] pci 0000:01:00.0: reg 0x14: [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.121752] pci 0000:01:00.0: reg 0x1c: [mem 0xee000000-0xefffffff 64bit pref]
[ 0.121762] pci 0000:01:00.0: reg 0x24: [io 0xdf00-0xdf7f]
[ 0.121773] pci 0000:01:00.0: reg 0x30: [mem 0xfcf00000-0xfcf7ffff pref]
[ 0.121887] pci 0000:01:00.1: [10de:0be3] type 00 class 0x040300
[ 0.121903] pci 0000:01:00.1: reg 0x10: [mem 0xfcffc000-0xfcffffff]
[ 0.126691] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.126697] pci 0000:00:01.0: bridge window [io 0xd000-0xdfff]
[ 0.126703] pci 0000:00:01.0: bridge window [mem 0xfb000000-0xfcffffff]
[ 0.126709] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xefffffff 64bit pref]
[ 0.126783] pci 0000:02:01.0: [1106:3044] type 00 class 0x0c0010
[ 0.126806] pci 0000:02:01.0: reg 0x10: [mem 0xfdeff000-0xfdeff7ff]
[ 0.126819] pci 0000:02:01.0: reg 0x14: [io 0xef00-0xef7f]
[ 0.126902] pci 0000:02:01.0: supports D2
[ 0.126905] pci 0000:02:01.0: PME# supported from D2 D3hot D3cold
[ 0.126989] pci 0000:02:05.0: [10ec:8169] type 00 class 0x020000
[ 0.127012] pci 0000:02:05.0: reg 0x10: [io 0xec00-0xecff]
[ 0.127025] pci 0000:02:05.0: reg 0x14: [mem 0xfdefe000-0xfdefe0ff]
[ 0.127075] pci 0000:02:05.0: reg 0x30: [mem 0xfdec0000-0xfdedffff pref]
[ 0.127109] pci 0000:02:05.0: supports D1 D2
[ 0.127113] pci 0000:02:05.0: PME# supported from D1 D2 D3hot D3cold
[ 0.127196] pci 0000:02:08.0: [8086:27dc] type 00 class 0x020000
[ 0.127218] pci 0000:02:08.0: reg 0x10: [mem 0xfdefd000-0xfdefdfff]
[ 0.127230] pci 0000:02:08.0: reg 0x14: [io 0xee00-0xee3f]
[ 0.127308] pci 0000:02:08.0: supports D1 D2
[ 0.127311] pci 0000:02:08.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.127410] pci 0000:00:1e.0: PCI bridge to [bus 02] (subtractive decode)
[ 0.127417] pci 0000:00:1e.0: bridge window [io 0xe000-0xefff]
[ 0.127423] pci 0000:00:1e.0: bridge window [mem 0xfde00000-0xfdefffff]
[ 0.127431] pci 0000:00:1e.0: bridge window [io 0x0000-0xffff] (subtractive decode)
[ 0.127435] pci 0000:00:1e.0: bridge window [mem 0x00000000-0xffffffff] (subtractive decode)
[ 0.127448] pci_bus 0000:00: on NUMA node 0
[ 0.128183] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[ 0.128303] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11 *12 14 15)
[ 0.128422] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 0.128542] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 0.128661] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[ 0.128780] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 0.128900] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 0.129019] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 0.129353] ACPI: Enabled 2 GPEs in block 00 to 1F
[ 0.129366] ACPI: \_SB_.PCI0: notify handler is installed
[ 0.129414] Found 1 acpi root devices
[ 0.129499] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.129499] vgaarb: loaded
[ 0.129499] vgaarb: bridge control possible 0000:01:00.0
[ 0.129499] PCI: Using ACPI for IRQ routing
[ 0.131455] PCI: pci_cache_line_size set to 64 bytes
[ 0.131514] e820: reserve RAM buffer [mem 0x00098800-0x0009ffff]
[ 0.131517] e820: reserve RAM buffer [mem 0xcfedf800-0xcfffffff]
[ 0.131681] NetLabel: Initializing
[ 0.131684] NetLabel: domain hash size = 128
[ 0.131686] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.131709] NetLabel: unlabeled traffic allowed by default
[ 0.131784] Switched to clocksource refined-jiffies
[ 0.141221] pnp: PnP ACPI init
[ 0.141249] ACPI: bus type PNP registered
[ 0.141516] system 00:00: [io 0x04d0-0x04d1] has been reserved
[ 0.141521] system 00:00: [io 0x0800-0x087f] has been reserved
[ 0.141526] system 00:00: [io 0x0880-0x088f] has been reserved
[ 0.141533] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.141554] pnp 00:01: [dma 4]
[ 0.141597] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.141664] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.141714] pnp 00:03: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.141773] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.142316] pnp 00:05: [dma 3]
[ 0.142386] pnp 00:05: Plug and Play ACPI device, IDs PNP0401 (active)
[ 0.142549] system 00:06: [io 0x0400-0x04bf] has been reserved
[ 0.142556] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.142624] pnp 00:07: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.143002] system 00:08: [mem 0xf0000000-0xf3ffffff] has been reserved
[ 0.143009] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.143327] system 00:09: [mem 0x000d4800-0x000d7fff] has been reserved
[ 0.143339] system 00:09: [mem 0x000f0000-0x000f7fff] could not be reserved
[ 0.143344] system 00:09: [mem 0x000f8000-0x000fbfff] could not be reserved
[ 0.143349] system 00:09: [mem 0x000fc000-0x000fffff] could not be reserved
[ 0.143353] system 00:09: [mem 0xcfee0000-0xcfefffff] could not be reserved
[ 0.143357] system 00:09: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.143361] system 00:09: [mem 0x00100000-0xcfedffff] could not be reserved
[ 0.143365] system 00:09: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.143370] system 00:09: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.143374] system 00:09: [mem 0xffb00000-0xffb7ffff] has been reserved
[ 0.143378] system 00:09: [mem 0xfff00000-0xffffffff] has been reserved
[ 0.143382] system 00:09: [mem 0x000e0000-0x000effff] has been reserved
[ 0.143387] system 00:09: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.143401] pnp: PnP ACPI: found 10 devices
[ 0.143404] ACPI: bus type PNP unregistered
[ 0.181586] Switched to clocksource acpi_pm
[ 0.181620] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.181626] pci 0000:00:01.0: bridge window [io 0xd000-0xdfff]
[ 0.181632] pci 0000:00:01.0: bridge window [mem 0xfb000000-0xfcffffff]
[ 0.181637] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xefffffff 64bit pref]
[ 0.181644] pci 0000:00:1e.0: PCI bridge to [bus 02]
[ 0.181649] pci 0000:00:1e.0: bridge window [io 0xe000-0xefff]
[ 0.181655] pci 0000:00:1e.0: bridge window [mem 0xfde00000-0xfdefffff]
[ 0.181797] pci 0000:00:1e.0: setting latency timer to 64
[ 0.181804] pci_bus 0000:00: resource 4 [io 0x0000-0xffff]
[ 0.181808] pci_bus 0000:00: resource 5 [mem 0x00000000-0xffffffff]
[ 0.181812] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff]
[ 0.181815] pci_bus 0000:01: resource 1 [mem 0xfb000000-0xfcffffff]
[ 0.181819] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xefffffff 64bit pref]
[ 0.181823] pci_bus 0000:02: resource 0 [io 0xe000-0xefff]
[ 0.181826] pci_bus 0000:02: resource 1 [mem 0xfde00000-0xfdefffff]
[ 0.181830] pci_bus 0000:02: resource 4 [io 0x0000-0xffff]
[ 0.181833] pci_bus 0000:02: resource 5 [mem 0x00000000-0xffffffff]
[ 0.181886] NET: Registered protocol family 2
[ 0.182168] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.182210] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.182250] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.182288] TCP: reno registered
[ 0.182293] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.182304] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.182388] NET: Registered protocol family 1
[ 0.182388] pci 0000:01:00.0: Boot video device
[ 0.182388] pci 0000:02:08.0: Firmware left e100 interrupts enabled; disabling
[ 0.182388] PCI: CLS 32 bytes, default 64
[ 0.182388] Unpacking initramfs...
[ 3.767636] Freeing initrd memory: 17220K (f672d000 - f77fe000)
[ 3.767832] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[ 3.767836] apm: disabled - APM is not SMP safe.
[ 3.767883] Scanning for low memory corruption every 60 seconds
[ 3.768350] audit: initializing netlink socket (disabled)
[ 3.768369] type=2000 audit(1400530145.763:1): initialized
[ 3.783776] bounce pool size: 64 pages
[ 3.783794] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 3.786252] zbud: loaded
[ 3.786379] VFS: Disk quotas dquot_6.5.2
[ 3.786456] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 3.786770] msgmni has been set to 1692
[ 3.787189] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 3.787246] io scheduler noop registered
[ 3.787250] io scheduler deadline registered
[ 3.787303] io scheduler cfq registered (default)
[ 3.787440] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[ 3.787553] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 3.787585] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 3.787808] GHES: HEST is not enabled!
[ 3.787828] isapnp: Scanning for PnP cards...
[ 4.143916] isapnp: No Plug & Play device found
[ 4.144002] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 4.144834] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 4.393708] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 4.393902] mousedev: PS/2 mouse device common for all mice
[ 4.394026] rtc_cmos 00:02: RTC can wake from S4
[ 4.394188] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 4.394220] rtc_cmos 00:02: alarms up to one month, 242 bytes nvram
[ 4.394271] cpuidle: using governor ladder
[ 4.394275] cpuidle: using governor menu
[ 4.394354] drop_monitor: Initializing network drop monitor service
[ 4.394463] TCP: cubic registered
[ 4.394689] NET: Registered protocol family 10
[ 4.394926] NET: Registered protocol family 17
[ 4.394941] Key type dns_resolver registered
[ 4.395148] Using IPI No-Shortcut mode
[ 4.395277] PM: Hibernation image not present or could not be loaded.
[ 4.395295] registered taskstats version 1
[ 4.395849] Magic number: 14:160:195
[ 4.395919] rtc_cmos 00:02: setting system clock to 2014-05-19 20:09:06 UTC (1400530146)
[ 4.396373] Freeing unused kernel memory: 608K (c06e9000 - c0781000)
[ 4.396483] Write protecting the kernel text: 4264k
[ 4.396526] Write protecting the kernel read-only data: 1360k
[ 4.409586] systemd-udevd[47]: starting version 208
[ 4.441220] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[ 4.441231] ACPI: Power Button [PWRB]
[ 4.441342] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 4.441349] ACPI: Power Button [PWRF]
[ 4.453112] Linux agpgart interface v0.103
[ 4.456375] [drm] Initialized drm 1.1.0 20060810
[ 4.458668] wmi: Mapper loaded
[ 4.464289] ACPI: bus type USB registered
[ 4.464341] usbcore: registered new interface driver usbfs
[ 4.464366] usbcore: registered new interface driver hub
[ 4.465442] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 4.465645] r8169 0000:02:05.0 (unregistered net_device): not PCI Express
[ 4.466029] r8169 0000:02:05.0 eth0: RTL8110s at 0xf850e000, 00:1e:2a:c2:08:13, XID 04000000 IRQ 17
[ 4.466034] r8169 0000:02:05.0 eth0: jumbo features [frames: 7152 bytes, tx checksumming: ok]
[ 4.466473] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[ 4.466476] e100: Copyright(c) 1999-2006 Intel Corporation
[ 4.468849] SCSI subsystem initialized
[ 4.470129] usbcore: registered new device driver usb
[ 4.472537] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.472967] uhci_hcd: USB Universal Host Controller Interface driver
[ 4.473145] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 4.473151] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 4.473162] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 4.473215] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000ff00
[ 4.474467] hub 1-0:1.0: USB hub found
[ 4.474476] hub 1-0:1.0: 2 ports detected
[ 4.476265] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 4.476273] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 4.476283] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 4.476285] ehci-pci: EHCI PCI platform driver
[ 4.476334] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000fe00
[ 4.477340] ACPI: bus type ATA registered
[ 4.478267] hub 2-0:1.0: USB hub found
[ 4.478276] hub 2-0:1.0: 2 ports detected
[ 4.478975] ehci-pci 0000:00:1d.7: setting latency timer to 64
[ 4.479324] ehci-pci 0000:00:1d.7: EHCI Host Controller
[ 4.479335] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 3
[ 4.483257] ehci-pci 0000:00:1d.7: cache line size of 32 is not supported
[ 4.483270] ehci-pci 0000:00:1d.7: irq 23, io mem 0xfdfff000
[ 4.483319] libata version 3.00 loaded.
[ 4.490116] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 4.490318] hub 3-0:1.0: USB hub found
[ 4.490328] hub 3-0:1.0: 8 ports detected
[ 4.497666] e100 0000:02:08.0 eth1: addr 0xfdefd000, irq 20, MAC addr 00:17:31:0e:7b:1b
[ 4.498311] nouveau [ DEVICE][0000:01:00.0] BOOT0 : 0x0a8280a2
[ 4.498316] nouveau [ DEVICE][0000:01:00.0] Chipset: GT218 (NVA8)
[ 4.498320] nouveau [ DEVICE][0000:01:00.0] Family : NV50
[ 4.499944] nouveau [ VBIOS][0000:01:00.0] checking PRAMIN for image...
[ 4.513467] hub 1-0:1.0: USB hub found
[ 4.513476] hub 1-0:1.0: 2 ports detected
[ 4.536751] hub 2-0:1.0: USB hub found
[ 4.536759] hub 2-0:1.0: 2 ports detected
[ 4.537041] ata_piix 0000:00:1f.1: version 2.13
[ 4.537215] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 4.538319] scsi0 : ata_piix
[ 4.539121] scsi1 : ata_piix
[ 4.539242] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfb00 irq 14
[ 4.539246] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfb08 irq 15
[ 4.539349] ahci 0000:00:1f.2: version 3.0
[ 4.539518] ahci 0000:00:1f.2: irq 41 for MSI/MSI-X
[ 4.539607] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl RAID mode
[ 4.539612] ahci 0000:00:1f.2: flags: 64bit ncq led clo
[ 4.539618] ahci 0000:00:1f.2: setting latency timer to 64
[ 4.540696] scsi2 : ahci
[ 4.540853] scsi3 : ahci
[ 4.540977] scsi4 : ahci
[ 4.541096] scsi5 : ahci
[ 4.541226] ata3: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe100 irq 41
[ 4.541231] ata4: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe180 irq 41
[ 4.541235] ata5: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe200 irq 41
[ 4.541239] ata6: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe280 irq 41
[ 4.541389] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 4.541395] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 4.541406] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 4.541450] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000fd00
[ 4.541676] hub 4-0:1.0: USB hub found
[ 4.541683] hub 4-0:1.0: 2 ports detected
[ 4.541931] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 4.541937] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 4.541946] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 4.541985] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000fc00
[ 4.542120] ata2: port disabled--ignoring
[ 4.542317] hub 5-0:1.0: USB hub found
[ 4.542325] hub 5-0:1.0: 2 ports detected
[ 4.563395] firewire_ohci 0000:02:01.0: added OHCI v1.0 device as card 0, 4 IR + 8 IT contexts, quirks 0x11
[ 4.574546] nouveau [ VBIOS][0000:01:00.0] ... appears to be valid
[ 4.574552] nouveau [ VBIOS][0000:01:00.0] using image from PRAMIN
[ 4.574662] nouveau [ VBIOS][0000:01:00.0] BIT signature found
[ 4.574667] nouveau [ VBIOS][0000:01:00.0] version 70.18.36.00.00
[ 4.575237] nouveau [ PFB][0000:01:00.0] RAM type: DDR2
[ 4.575243] nouveau [ PFB][0000:01:00.0] RAM size: 512 MiB
[ 4.575247] nouveau [ PFB][0000:01:00.0] ZCOMP: 960 tags
[ 4.713759] ata1.00: ATAPI: TSSTcorpCD/DVDW TS-H652L, 0803, max UDMA/33
[ 4.743671] ata1.00: configured for UDMA/33
[ 4.744629] scsi 0:0:0:0: CD-ROM TSSTcorp CD/DVDW TS-H652L 0803 PQ: 0 ANSI: 5
[ 4.770051] tsc: Refined TSC clocksource calibration: 3000.853 MHz
[ 4.860047] ata3: SATA link down (SStatus 0 SControl 300)
[ 5.020046] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 5.020077] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 5.021034] ata5.00: ATA-6: WDC WD800BB-00JHC0, 05.01C05, max UDMA/100
[ 5.021039] ata5.00: 156301488 sectors, multi 0: LBA
[ 5.021915] ata5.00: configured for UDMA/100
[ 5.023691] ata4.00: ATA-6: WDC WD800BB-00JHC0, 05.01C05, max UDMA/100
[ 5.023695] ata4.00: 156301488 sectors, multi 0: LBA
[ 5.024602] ata4.00: configured for UDMA/100
[ 5.024731] scsi 3:0:0:0: Direct-Access ATA WDC WD800BB-00JH 05.0 PQ: 0 ANSI: 5
[ 5.025019] scsi 4:0:0:0: Direct-Access ATA WDC WD800BB-00JH 05.0 PQ: 0 ANSI: 5
[ 5.063459] firewire_core 0000:02:01.0: created device fw0: GUID 0011d800009e9dd1, S400
[ 5.090025] usb 1-1: new low-speed USB device number 2 using uhci_hcd
[ 5.180043] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 5.184039] ata6.00: ATA-6: ST380011A, 3.04, max UDMA/100
[ 5.184044] ata6.00: 156301488 sectors, multi 0: LBA48
[ 5.188337] ata6.00: configured for UDMA/100
[ 5.188461] scsi 5:0:0:0: Direct-Access ATA ST380011A 3.04 PQ: 0 ANSI: 5
[ 5.199621] sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[ 5.199627] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 5.199923] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 5.200185] sd 3:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 5.200346] sd 3:0:0:0: [sda] Write Protect is off
[ 5.200351] sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.200393] sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.200900] sd 4:0:0:0: [sdb] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 5.200997] sd 4:0:0:0: [sdb] Write Protect is off
[ 5.201002] sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 5.201043] sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.201527] sd 5:0:0:0: [sdc] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 5.201623] sd 5:0:0:0: [sdc] Write Protect is off
[ 5.201627] sd 5:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 5.201669] sd 5:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.207456] sdc: sdc1
[ 5.207886] sd 5:0:0:0: [sdc] Attached SCSI disk
[ 5.235174] sda: sda1 sda2 < sda5 >
[ 5.235744] sd 3:0:0:0: [sda] Attached SCSI disk
[ 5.237596] sdb: sdb1 sdb2 < sdb5 >
[ 5.238117] sd 4:0:0:0: [sdb] Attached SCSI disk
[ 5.260907] hidraw: raw HID events driver (C) Jiri Kosina
[ 5.277654] usbcore: registered new interface driver usbhid
[ 5.277659] usbhid: USB HID core driver
[ 5.280199] input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1d.0/usb1/1-1/1-1:1.0/input/input2
[ 5.280357] hid-generic 0003:413C:2003.0001: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1d.0-1/input0
[ 5.770105] Switched to clocksource tsc
[ 6.481687] nouveau [ PTHERM][0000:01:00.0] FAN control: none / external
[ 6.481702] nouveau [ PTHERM][0000:01:00.0] fan management: disabled
[ 6.481708] nouveau [ PTHERM][0000:01:00.0] internal sensor: yes
[ 6.481900] [TTM] Zone kernel: Available graphics memory: 433706 kiB
[ 6.481904] [TTM] Zone highmem: Available graphics memory: 1682412 kiB
[ 6.481907] [TTM] Initializing pool allocator
[ 6.481924] nouveau [ DRM] VRAM: 512 MiB
[ 6.481927] nouveau [ DRM] GART: 1048576 MiB
[ 6.481933] nouveau [ DRM] TMDS table version 2.0
[ 6.481936] nouveau [ DRM] DCB version 4.0
[ 6.481940] nouveau [ DRM] DCB outp 00: 01000302 00020030
[ 6.481944] nouveau [ DRM] DCB outp 01: 02000300 00000000
[ 6.481948] nouveau [ DRM] DCB outp 03: 02011362 00020010
[ 6.481951] nouveau [ DRM] DCB outp 04: 01022310 00000000
[ 6.481954] nouveau [ DRM] DCB conn 00: 00001030
[ 6.481959] nouveau [ DRM] DCB conn 01: 00202161
[ 6.481964] nouveau [ DRM] DCB conn 02: 00000200
[ 6.505501] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 6.505505] [drm] No driver support for vblank timestamp query.
[ 6.505631] nouveau [ DRM] 2 available performance level(s)
[ 6.505637] nouveau [ DRM] 1: core 405MHz shader 810MHz memory 405MHz voltage 900mV
[ 6.505642] nouveau [ DRM] 3: core 589MHz shader 1402MHz memory 405MHz voltage 1000mV
[ 6.505646] nouveau [ DRM] c: core 405MHz shader 810MHz memory 405MHz voltage 900mV
[ 6.531333] nouveau [ DRM] MM: using COPY for buffer copies
[ 6.581567] nouveau [ DRM] allocated 1280x1024 fb: 0x70000, bo f7015a00
[ 6.581724] fbcon: nouveaufb (fb0) is primary device
[ 6.653923] Console: switching to colour frame buffer device 160x64
[ 6.655952] nouveau 0000:01:00.0: fb0: nouveaufb frame buffer device
[ 6.655955] nouveau 0000:01:00.0: registered panic notifier
[ 6.655962] [drm] Initialized nouveau 1.1.1 20120801 for 0000:01:00.0 on minor 0
[ 7.082698] ISO 9660 Extensions: RRIP_1991A
[ 7.168774] loop: module loaded
[ 8.253583] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 8.355925] device-mapper: uevent: version 1.0.3
[ 8.356608] device-mapper: ioctl: 4.25.0-ioctl (2013-06-26) initialised: [email protected]
[ 8.362693] bio: create slab <bio-1> at 1
[ 8.386733] EXT4-fs (dm-0): mounted filesystem without journal. Opts: (null)
[ 10.338096] systemd[1]: systemd 208 running in system mode. (+PAM -LIBWRAP -AUDIT -SELINUX -IMA -SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
[ 10.417677] systemd[1]: Set hostname to <archiso>.
[ 10.724871] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 10.724981] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 10.725005] systemd[1]: Starting Remote File Systems.
[ 10.725151] systemd[1]: Reached target Remote File Systems.
[ 10.725172] systemd[1]: Starting LVM2 metadata daemon socket.
[ 10.725323] systemd[1]: Listening on LVM2 metadata daemon socket.
[ 10.725343] systemd[1]: Starting Delayed Shutdown Socket.
[ 10.725469] systemd[1]: Listening on Delayed Shutdown Socket.
[ 10.725488] systemd[1]: Starting Device-mapper event daemon FIFOs.
[ 10.725627] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 10.725646] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 10.725770] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 10.725790] systemd[1]: Starting Root Slice.
[ 10.726156] systemd[1]: Created slice Root Slice.
[ 10.726176] systemd[1]: Starting User and Session Slice.
[ 10.726413] systemd[1]: Created slice User and Session Slice.
[ 10.726434] systemd[1]: Starting System Slice.
[ 10.726647] systemd[1]: Created slice System Slice.
[ 10.726682] systemd[1]: Starting system-getty.slice.
[ 10.726921] systemd[1]: Created slice system-getty.slice.
[ 10.726941] systemd[1]: Starting Slices.
[ 10.727040] systemd[1]: Reached target Slices.
[ 10.727064] systemd[1]: Starting Journal Socket.
[ 10.727235] systemd[1]: Listening on Journal Socket.
[ 10.727662] systemd[1]: Starting Load Kernel Modules...
[ 10.728292] systemd[1]: Mounting POSIX Message Queue File System...
[ 10.880863] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 10.881454] systemd[1]: Starting Journal Service...
[ 10.882180] systemd[1]: Started Journal Service.
[ 11.716066] systemd-journald[149]: Vacuuming done, freed 0 bytes
[ 11.916159] FS-Cache: Loaded
[ 12.202893] RPC: Registered named UNIX socket transport module.
[ 12.202899] RPC: Registered udp transport module.
[ 12.202902] RPC: Registered tcp transport module.
[ 12.202904] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 12.619444] FS-Cache: Netfs 'nfs' registered for caching
[ 12.812715] systemd-udevd[181]: starting version 208
[ 12.905896] systemd-journald[149]: Received request to flush runtime journal from PID 1
[ 15.580133] thermal LNXTHERM:00: registered as thermal_zone0
[ 15.580139] ACPI: Thermal Zone [THRM] (40 C)
[ 15.915160] ACPI: Fan [FAN] (on)
[ 16.002108] ACPI Warning: 0x00000428-0x0000042f SystemIO conflicts with Region \PM2S 1 (20130517/utaddress-251)
[ 16.002119] ACPI Warning: 0x00000428-0x0000042f SystemIO conflicts with Region \PM1K 2 (20130517/utaddress-251)
[ 16.002126] ACPI Warning: 0x00000428-0x0000042f SystemIO conflicts with Region \GPE1 3 (20130517/utaddress-251)
[ 16.002133] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 16.002139] ACPI Warning: 0x000004b0-0x000004bf SystemIO conflicts with Region \GPO2 1 (20130517/utaddress-251)
[ 16.002145] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 16.002148] ACPI Warning: 0x00000480-0x000004af SystemIO conflicts with Region \GPIV 1 (20130517/utaddress-251)
[ 16.002153] ACPI Warning: 0x00000480-0x000004af SystemIO conflicts with Region \GPO_ 2 (20130517/utaddress-251)
[ 16.002158] ACPI Warning: 0x00000480-0x000004af SystemIO conflicts with Region \PALD 3 (20130517/utaddress-251)
[ 16.002164] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 16.002166] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 16.342474] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 16.403348] leds_ss4200: no LED devices found
[ 16.664449] parport_pc 00:05: reported by Plug and Play ACPI
[ 16.664509] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 16.686843] systemd-udevd[203]: renamed network interface eth0 to enp2s5
[ 16.770163] systemd-udevd[209]: renamed network interface eth1 to enp2s8
[ 17.098798] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 17.779883] i801_smbus 0000:00:1f.3: SMBus using PCI Interrupt
[ 17.780620] ppdev: user-space parallel port driver
[ 17.849790] microcode: CPU0 sig=0xf62, pf=0x4, revision=0xf
[ 17.944384] iTCO_vendor_support: vendor-support=0
[ 17.946278] microcode: CPU1 sig=0xf62, pf=0x4, revision=0xf
[ 17.947486] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
[ 17.950629] r8169 0000:02:05.0 enp2s5: link down
[ 17.950649] r8169 0000:02:05.0 enp2s5: link down
[ 17.950666] IPv6: ADDRCONF(NETDEV_UP): enp2s5: link is not ready
[ 17.965112] IPv6: ADDRCONF(NETDEV_UP): enp2s8: link is not ready
[ 18.405080] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
[ 18.405126] iTCO_wdt: Found a ICH7DH TCO device (Version=2, TCOBASE=0x0460)
[ 18.405284] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 18.872915] snd_hda_intel 0000:00:1b.0: irq 42 for MSI/MSI-X
[ 19.433622] hda_codec: ALC882: SKU not ready 0x411111f0
[ 19.445025] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input4
[ 19.479013] input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5
[ 19.479156] input: HDA Intel Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
[ 19.479804] hda_intel: Disabling MSI
[ 19.479816] hda-intel 0000:01:00.1: Handle VGA-switcheroo audio client
[ 20.178014] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input7
[ 20.178270] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input8
[ 20.178485] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input9
[ 20.178696] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input10
[44490.433683] md: bind<sda1>
[44490.446722] md: bind<sdb1>
[44490.449241] md: raid1 personality registered for level 1
[44490.450198] md/raid1:md1: not clean -- starting background reconstruction
[44490.450203] md/raid1:md1: active with 2 out of 2 mirrors
[44490.450235] md1: detected capacity change from 0 to 75934400512
[44490.452050] md: resync of RAID array md1
[44490.452056] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[44490.452059] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync.
[44490.452064] md: using 128k window, over a total of 74154688k.
[44490.454641] md1: unknown partition table
[45968.754029] md: md1: resync done.
[45968.841250] RAID1 conf printout:
[45968.841254] --- wd:2 rd:2
[45968.841258] disk 0, wo:0, o:1, dev:sda1
[45968.841261] disk 1, wo:0, o:1, dev:sdb1
[47642.847783] EXT4-fs (md1): mounted filesystem with ordered data mode. Opts: (null)
[47687.134362] r8169 0000:02:05.0 enp2s5: link up
[47687.134376] IPv6: ADDRCONF(NETDEV_CHANGE): enp2s5: link becomes ready
[47825.775238] usb 3-6: new high-speed USB device number 3 using ehci-pci
[47825.899362] usb 3-6: unable to get BOS descriptor set
[47826.017245] usb-storage 3-6:1.0: USB Mass Storage device detected
[47826.017363] scsi6 : usb-storage 3-6:1.0
[47826.017504] usbcore: registered new interface driver usb-storage
[47827.081919] scsi 6:0:0:0: Direct-Access PMAP PQ: 0 ANSI: 4
[47827.802316] sd 6:0:0:0: [sdd] 15466496 512-byte logical blocks: (7.91 GB/7.37 GiB)
[47827.804809] sd 6:0:0:0: [sdd] Write Protect is off
[47827.804814] sd 6:0:0:0: [sdd] Mode Sense: 23 00 00 00
[47827.807314] sd 6:0:0:0: [sdd] No Caching mode page found
[47827.807763] sd 6:0:0:0: [sdd] Assuming drive cache: write through
[47827.816453] sd 6:0:0:0: [sdd] No Caching mode page found
[47827.816915] sd 6:0:0:0: [sdd] Assuming drive cache: write through
[47827.845089] sdd: sdd1
[47827.851818] sd 6:0:0:0: [sdd] No Caching mode page found
[47827.852305] sd 6:0:0:0: [sdd] Assuming drive cache: write through
[47827.852776] sd 6:0:0:0: [sdd] Attached SCSI removable disk
[47901.177187] FAT-fs (sdd1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[48255.001967] usb 3-6: USB disconnect, device number 3
[48456.278507] usb 3-6: new high-speed USB device number 4 using ehci-pci
[48456.402614] usb 3-6: unable to get BOS descriptor set
[48456.425683] usb-storage 3-6:1.0: USB Mass Storage device detected
[48456.425763] scsi7 : usb-storage 3-6:1.0
[48457.491544] scsi 7:0:0:0: Direct-Access PMAP PQ: 0 ANSI: 4
[48458.209938] sd 7:0:0:0: [sdd] 15466496 512-byte logical blocks: (7.91 GB/7.37 GiB)
[48458.212437] sd 7:0:0:0: [sdd] Write Protect is off
[48458.212442] sd 7:0:0:0: [sdd] Mode Sense: 23 00 00 00
[48458.214932] sd 7:0:0:0: [sdd] No Caching mode page found
[48458.215426] sd 7:0:0:0: [sdd] Assuming drive cache: write through
[48458.224684] sd 7:0:0:0: [sdd] No Caching mode page found
[48458.225143] sd 7:0:0:0: [sdd] Assuming drive cache: write through
[48458.253332] sdd: sdd1
[48458.265813] sd 7:0:0:0: [sdd] No Caching mode page found
[48458.266295] sd 7:0:0:0: [sdd] Assuming drive cache: write through
[48458.266755] sd 7:0:0:0: [sdd] Attached SCSI removable disk
[48470.450341] FAT-fs (sdd1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[50093.387926] Adding 3930408k swap on /dev/sda5. Priority:-1 extents:1 across:3930408k FS
[50096.410969] Adding 3930408k swap on /dev/sdb5. Priority:-2 extents:1 across:3930408k FS
[54374.314336] ata4.00: exception Emask 0x50 SAct 0x0 SErr 0x480900 action 0x6 frozen
[54374.314836] ata4.00: irq_stat 0x08000000, interface fatal error
[54374.315323] ata4: SError: { UnrecovData HostInt 10B8B Handshk }
[54374.315764] ata4.00: failed command: WRITE DMA
[54374.316198] ata4.00: cmd ca/00:88:9f:ca:8d/00:00:00:00:00/e8 tag 0 dma 69632 out
res 50/00:00:9e:ca:8d/00:00:9e:c9:8d/e8 Emask 0x50 (ATA bus error)
[54374.317334] ata4.00: status: { DRDY }
[54374.318002] ata4: hard resetting link
[54374.904585] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[54374.906314] ata4.00: configured for UDMA/100
[54374.906332] ata4: EH complete
[56161.610355] sdd: detected capacity change from 7918845952 to 0
[56178.066775] usb 3-6: USB disconnect, device number 4
[56193.205154] ata6: exception Emask 0x50 SAct 0x0 SErr 0x90800 action 0xe frozen
[56193.205703] ata6: irq_stat 0x00400000, PHY RDY changed
[56193.206232] ata6: SError: { HostInt PHYRdyChg 10B8B }
[56193.206732] ata6: hard resetting link
[56193.924403] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[56193.932798] ata6.00: configured for UDMA/100
[56193.932805] ata6: EH complete
[56195.044927] ata6: exception Emask 0x10 SAct 0x0 SErr 0x90000 action 0xe frozen
[56195.045472] ata6: irq_stat 0x00400000, PHY RDY changed
[56195.046003] ata6: SError: { PHYRdyChg 10B8B }
[56195.046511] ata6: hard resetting link
[56195.764407] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[56195.772826] ata6.00: configured for UDMA/100
[56195.772832] ata6: EH complete
[56217.331067] usb 3-6: new high-speed USB device number 5 using ehci-pci
[56217.455149] usb 3-6: unable to get BOS descriptor set
[56217.478526] usb-storage 3-6:1.0: USB Mass Storage device detected
[56217.478662] scsi8 : usb-storage 3-6:1.0
[56218.544212] scsi 8:0:0:0: Direct-Access PMAP PQ: 0 ANSI: 4
[56219.262349] sd 8:0:0:0: [sdd] 15466496 512-byte logical blocks: (7.91 GB/7.37 GiB)
[56219.264849] sd 8:0:0:0: [sdd] Write Protect is off
[56219.264855] sd 8:0:0:0: [sdd] Mode Sense: 23 00 00 00
[56219.267343] sd 8:0:0:0: [sdd] No Caching mode page found
[56219.267939] sd 8:0:0:0: [sdd] Assuming drive cache: write through
[56219.277220] sd 8:0:0:0: [sdd] No Caching mode page found
[56219.277802] sd 8:0:0:0: [sdd] Assuming drive cache: write through
[56219.305984] sdd: sdd1
[56219.318099] sd 8:0:0:0: [sdd] No Caching mode page found
[56219.318677] sd 8:0:0:0: [sdd] Assuming drive cache: write through
[56219.319238] sd 8:0:0:0: [sdd] Attached SCSI removable disk
[56234.556099] FAT-fs (sdd1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
Edit: Just after I took out my flashdrive, when I accidentally bumped one of the HDs, this popped up:
[56193.205154] ata6: exception Emask 0x50 SAct 0x0 SErr 0x90800 action 0xe frozen
[56193.205703] ata6: irq_stat 0x00400000, PHY RDY changed
[56193.206232] ata6: SError: { HostInt PHYRdyChg 10B8B }
[56193.206732] ata6: hard resetting link
[56193.924403] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[56193.932798] ata6.00: configured for UDMA/100
[56193.932805] ata6: EH complete
[56195.044927] ata6: exception Emask 0x10 SAct 0x0 SErr 0x90000 action 0xe frozen
[56195.045472] ata6: irq_stat 0x00400000, PHY RDY changed
[56195.046003] ata6: SError: { PHYRdyChg 10B8B }
[56195.046511] ata6: hard resetting link
Last edited by Dornith (2014-05-20 16:08:40)http://ww2.cs.fsu.edu/~rosentha/linux/2.6.26.5/docs/DocBook/libata/ch07.html#excatATAbusErr wrote:
ATA bus error means that data corruption occurred during transmission over ATA bus (SATA or PATA). This type of errors can be indicated by
ICRC or ABRT error as described in the section called “ATA/ATAPI device error (non-NCQ / non-CHECK CONDITION)”.
Controller-specific error completion with error information indicating transmission error.
On some controllers, command timeout. In this case, there may be a mechanism to determine that the timeout is due to transmission error.
Unknown/random errors, timeouts and all sorts of weirdities.
As described above, transmission errors can cause wide variety of symptoms ranging from device ICRC error to random device lockup, and, for many cases, there is no way to tell if an error condition is due to transmission error or not; therefore, it's necessary to employ some kind of heuristic when dealing with errors and timeouts. For example, encountering repetitive ABRT errors for known supported command is likely to indicate ATA bus error.
Once it's determined that ATA bus errors have possibly occurred, lowering ATA bus transmission speed is one of actions which may alleviate the problem.
I'd also add; make sure you have good backups when ATA errors are frequent -
I am trying to configure a particular SNMP community string on many ATAs for a Cisco 'Know the Network' project. On a Cisco ATA 186, you cannot telnet or SSH to it and the only way to remotely change the parameters are via the web GUI, which doesn't have the SNMP field available.
Is this possible without getting physical console access to the ATA?No.
An ASA can, as you noted, restrict source and destination IP and port. To do what you are asking, one would need to prevent a string within the payload from being transmitted (or only accept certain strings).
You should just put the access-list on the destination device(s) restricting what host(s) are allowed snmp rw (as you alluded to). That's a very common implementation straight out of the textbook. -
!!cisco ATA 186, back to back.SOS
hi there, just enlighten me on cisco ATA 186 back to back config, my network is like:
phone---ATA----Switch---ATA---Phone,wnat to know the sample config, if this not possible, fine ,then let me know what shud i configure to get a dial tone,as im getting a busy tone than a dial tone, or lastly what shud i do to reset the ATAs to factory default settings,
cheers
shukkyIf your ATA is running skinny right now then I think it is not possible (because no callmanager in the picture).
But if you load your ATA with a SIP image then in the SIP proxy filed, you can specify the IP address of the other SIP ATA and then you should be able to call from one ATA to another.
I haven't tried that with the ATA, but done with the 7940 phones and it worked.
To get the dial-tone, you must configure a number for the ATA first. (UID)
To reset the ATA for factory defaults
http://lists.digium.com/pipermail/asterisk-users/2003-August/017474.html
Hope this would help.
Thanks -
ATA 186 Reproducing DTMF tones from RFC2833 events
I am trying to get my ATA 186 (running version SCCP 3.x under CCM 5.04a) to reproduce received rtp-events. This is supporting a third-party IVR system that is connected via analog ports.
The IOS gateway that is sending the events is configured for dtmf-relay rtp-nte, and I can see the RTP events being received at the ATA. However, all I hear at the ATA is nothing or clicks.
I have the audiomode setting on the ATA set to 0x00150015 as is recommended in the ATA administrators guide.
Does anyone have DTMF working through the ATA?Hi Kevin,
have you debugged the ATA with prserv.exe?
I had some issues in the past with a PESQ tester, and setting the audiomode to 0x00120012 helped for me.
hth
Sascha
....this is the output from prserv on a good call
|->CallState[0]=4 L=1 R=4016c6c FG=0 r=0,0
FG NewState[0]=4, L=1, R=4016c6c
|->CallInfo[0]
|->SetRingerMode[0]:3
<-|StOffHk[0]
|->SetRingerMode[0]:1
|->CallState[0]=1 L=1 R=4016c6c FG=0 r=4016c6c,0
|->SetRingerMode[0]:1
[0]StopTone
|->CallState[0]=5 L=1 R=4016c6c FG=0 r=4016c6c,0
|->CallInfo[0]
[0]StopTone
|->OpenRxChn[0]
[0]StopTone
<-|OpenRxChnAck[0]
Save Media[0]
|->StartMediaTx[0]:pt=0 ps=20 ss=0 ip=a63801f:19422
[0]MPT mode 0
[2]MPT mode 0
Enable LEC adapt [0]=1
[0]Enable encoder 0
[0]DPKT 1st: 3680 3520, pt 0
15948:00;2,0,0,0,
[0]DTMF 1 , insum:323505
[0]StopTone
[0]DTMF 2 , insum:285988
[0]DTMF 3 , insum:289227
[0]DTMF 4 , insum:287021
[0]DTMF 5 , insum:284108
[0]DTMF 6 , insum:286979
[0]DTMF 7 , insum:284993
[0]DTMF 8 , insum:302792
[0]DTMF 9 , insum:293475
[0]DTMF 0 , insum:293768
[0]DTMF * , insum:279360
[0]DTMF # , insum:301230
<-|EndCall[0]
<-|SK[0]:9, L=1, FGR=4016c6c
[0]StopTone
->CloseRxChn[0]
|->StopMediaTx[0]
|->CallState[0]=2 L=1 R=4016c6c FG=0 r=4016c6c,0
IDLE[0]
|->SetRingerMode[0]:1
15948:30;2,0,0,0, -
Hi,
I have an issue with ATA 186 to send faxes. I have tried many things, but the fax sending is unsuccessful. I am not a VoIP expert, so it is pretty hard to me to identify the difference between some commands. This is the topology of the network:
Fax Machine --- ATA ---- CCM ---- VoIPGW --- E1(PSTN)
I have the following values in ATA:
AudioMode: 0x00120012
ConnectMode: 0x00008400
This is the dial-peer configured to that Fax:
dial-peer voice 1010 voip
call-block translation-profile incoming 110
call-block disconnect-cause incoming call-reject
preference 1
destination-pattern 1044
voice-class h323 1
session target ipv4:10.15.190.4
dtmf-relay cisco-rtp h245-signal h245-alphanumeric
codec g711ulaw
fax rate disable
fax protocol pass-through g711ulaw
no vad
Aditionaly I had the following lines in VoIPGW:
ccm-manager fax protocol cisco
mgcp
mgcp fax t38 ecm
Recently I changed to:
no ccm-manager fax protocol cisco
mgcp
mgcp fax t38 inhibit
Not sure if I missing something, in the other hand I would like to know which is the different between fax protocol pass-through g711ulaw and modem passthrough nse codec g711ulaw
Thanks for your comments....Hello,
There is one relly important detail on this matter, is the fax machine a super G3 fax machine? this is because as you mention there are some limitation for the ATAs to work with fax machines and modems, this is because the device was not designed for this purpose.}
In the follow link you could find some information about the ATA configuration for faxing:
http://www.cisco.com/en/US/partner/products/hw/gatecont/ps514/products_qanda_item09186a00800946e1.shtml
Another important detail is check if your gateway supports the type of faxing that you are trying to do
http://www.cisco.com/en/US/partner/tech/tk652/tk777/technologies_tech_note09186a0080159cf3.shtml
Finally this are the configuration steps for you voice gaway:
http://www.cisco.com/en/US/partner/docs/ios/12_3/vvf_c/cisco_ios_fax_services_over_ip_application_guide/pt.html
HTH
<-------------------->
Walter Solano
CCNA Voice
UCCX Specialis -
ATA 186 needs assistance configuring to work with SIP
Hello. Just got ATA 186. I would like to use it as SIP FXS. I already have FXO with the POTS plugged in. I don't want o use the gateway or the gatekeeper. I would like to configure it to be IP dialing. II am running SIP image ATA030201SIP050616A.zup. Any help is greatly appreciated.
GeorgeHello, already replied in another thread, please do not open duplicates.
-
ATA-186 can be registered with CUCM v10.5
Hello guys ;
Please confirm me that ATA-186 can work with CUCM v10.5 ? .
Regards;
ShibLoaded the latest firmware into CM, then manually on ATA firmware using this process as CM didn't change it:
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cata/186_188/3_0/english/administration/guide/sccp/sccp3_0/sccpaapc.html#wp1011450
I followed this link from another post regarding ASA not registering for an older issue.
http://www.cisco.com/en/US/docs/voice_ip_comm/cata/186_188/3_0/english/administration/guide/sccp/sccpaape.html#wpxref59054
Follow the part that mentions setting the SID0 & SID1 to "." no quotes. I did this and my ATA registered to CM. Screen caps attached.
I have a Cisco ATA 186 running on 10.5.1 and it shows to be registered. I can make calls on it. Not sure how it will do for faxes. HTH Please rate. -
Hi,
I have ATA 186 connected to my network when i connect a phone it works but when I connected fax machine i cannot recieve or send faxes...do I need to do any configurations in ATA...please check the attachment..you'll need dial peer(s), on your CME router, that enable FAX passthrough as well as a few other pieces.
please see the following link for Config/Troubleshooting ATA-186 with FAX:
http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_configuration_example09186a00800d698e.shtml#task2 -
ATA 186 - Faxing with sccp on CCME
Is there any specific config required to get a fax working with an ATA 186 with sccp, both in the ATA settings and ccme config ?
Any useful links or example configs would be a great help
Thanks in advanceHey Mark,
Here are some good ATA - Fax related docs;
Field Notice: Fax Passthrough Limitations on ATA 186
http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_field_notice09186a0080094af7.shtml
Configuring the Cisco ATA for SCCP
http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_administration_guide_chapter09186a00801e0e0c.html
Configuring and Debugging Fax Services
http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_administration_guide_chapter09186a00801e0dff.html
Hope this helps!
Rob -
ATA-186 with overhead paging systems
Since the ATA-186 supplies 600 Ohms, would I need a seperate device such as a Bogen TAM-B to supplie the audio for overhead paging, or could I just use the ATA-186?
ATA-186 can be used as an audio source.
-
The remote-party-id field in my invite message to an ATA 186 does not appear to be tranlating properly to caller-id. Does the ATA support Remote-Party-ID? If so, do I have to modify any settings? Currently, the from address is showing up in the caller-id screen of a phone connected to the ATA.
Thanks,
StephenHello,
Can You please forward the URL which tells the configuration part to be taken place
Regards
pavan.M -
Hello
There are a atas186 who was registered to a CUCM version 6.1,the call manager was migrated to version 8.6 but now the second por when a call is answered immediately when give a fast busy tone, the first port works perfect, and i have changed many parameters and did a factory reset without success.
S/W Version 3.02.04(090202A)
App Load ID ATA030204SCCP090202A
Thanks.Your ata´s place calls across the wan?
If yes, the the ata 186, only support one port in g729 codec the port 0, the second port works only in g711 codec so try to configure a region to place calls only in g711 codec across the wan and problem solve
i hope it helps... -
Configuring FAX on ATA 186 with CME 3.4
Hi,
I have an ATA 186 connected to my network, I have configured CME for auto assign extensions & I got an extension as well, when I connect analog phone it works fine but when I connect FAX Machine I cannot send & recieve fax. Do I need to change any configurations in ATA???? Please check the screen shot attachedTry this link for more information on configuraing FAX on ATA
http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_configuration_example09186a00800d698e.shtml
Maybe you are looking for
-
hi all, i have a problem with portfoarwarding on asa 5505. i have this situation: internet ---> pubblic ip address-> router albacom -- 10.0.0.15 ---> -nat farward port 80--10.0.0.1 -outside -firewall asa -inside - 192.168.0.1------------server web 19
-
AVAILABILITY OF TV-OUT CABLE FOR NOKIA 5800 XM
CAN ANYONE TELL ME FROM WHERE CAN I GET NOKIA TV-OUT CABLE ( CA-75U) FOR MY NOKIA 5800 XM IN GUJARAT STATE? ANY STORE IN GUJARAT WHERE CAN I FIND THIS? ITS NOT AVAILABLE AT NOKIA PRIORITY STORES. PLS HELP ON THIS..........................
-
how do i see what photos are stored in my icloud. I cannot do this without installing 8.0 or above which i cannot do as i do not have enough space on my iphone. I do not want to delete the pics to make enough room to install 8.0 without checking fi
-
Recursive relationship in Forms
Greetings: I have a table containing a recursive relationship representing an organizational heirarchy. I have an Org_ID (sequence) field as the pkey and a parent_org_ID field to relate each company in the table to it's parent company in the same tab
-
Hi, I am using Sun Studio Creator to develop a portal application. Obviously, I need a portal container to deploy my portlets to. Who would host a Java Portal Server System? Do you have a solution for that? Note: My Java skills are kind of limited. T