Avoid Read New Routing during conversion in CO41

Dear guru ,
i try to convert a planned order into a production order with CO41.
When I run the conversion the system read master data with actual version of routing.
I want to run the conversion and maintain the routing copied from planned order.
What do you suggest for solving this problem ?
Thanks for your help.

Hi,
Once u despatch the Planned Order at CM25 , Capacity requirement is scheduled on that Particular date.Results in "Capacity scheduled" check box has been activated for Planned Order.
When u convert that planned order to production Order, scheduling will done on same date only ie as scheduled in Planned order.
Maybe based on settings at OPU3, order start & finish date will be changed to Operation date.inthat case set donot Adjust date for scheduling at OPU3 for Order type.
Pradeep

Similar Messages

Help needed choosing a new router

Hi there,
Our company is in need of a new router for internet traffic. Because I'm having trouble selecting a model, I would like to ask for your help on this one. Our situation is as follows:
- Primary internet connection is a 60/10 Mbps cable connection.
- Backup internet connection is an ADSL connection (not normally in use)
- Currently our old DrayTek Vigor 2910 is incapable of processing more than 25 Mbps.
- We have approximately 35 users working in our office.
- Traffic primarily consists of web browsing, e-mail and VOIP phone calls.
When the need arises, we would like to have the option of adding an additional cable connections for more bandwidth.
Additionally, we would like to replace our OpenVPN server with Cisco VPN on this new router, which should handle about 5 users during daytime and 10 outside of office hours.
I have narrowed it down to a 2900-series router because of the flexibility provided by the EHWIC slots. I have found the following models:
Model
WAN performance
Realistic performance
Cisco 2901
25 Mbps
167 Mbps
Cisco 2911
35 Mbps
181 Mbps
Cisco 2921
50 Mbps
246 Mbps
Cisco 2951
75 Mbps
297 Mbps
These performance numbers confuse me as to which model to choose.

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
See if attachment helps.

Photosmart C4780 won't work with my new router.

Hi
I have been sent a new plusnet TG582n router after my old one broke and now my wireless printer won't work.
I have tried uninstalling the software and connecting the printer via USB to reinstall on my windows 7 netbook but it came up with drivers failed to install.
On my windows 8.1 laptop I have uninstalled and reinstalled and this was unable to complete. I have now done a restore to a previous setting on both of them so the software and drivers are still on.
I have tried connecting my printer via USB cable but this tries to install the software again.
If I go into devices my printer shows up with error and won't print.
After trying all this I have now done a restore on the printer to factore settings (also trying the uninstall and reinstall via USB after this) and it still won't work.
After doing a wireless test report it came up with my old ssid initially even after installing my new router which has a new ssid. After resetting the printer it now comes up with SigmaplusEOL1. It shows on the report that wirelss is on and working but ssid fail.
I don't know what else to try as I have spent hours tyring different things and done trouble shooting several times.
I have also been told by plusnet that t he routershould work for wireless n or wireless g.
Please help!

Hi Tazza,
Welcome to the HP Forums! I understand that your HP Photosmart C4780, will not work with your new router. I am happy to help you with this! I believe these following guides should help:
The Printer is Not Found During Wireless Network Installation in Windows.
Printer Does Not Maintain Wireless Connection.
Just to make sure the hardware is functional, can you make copies standalone with the printer? Or what happens when you print a status report? Video of Printing a status report.
Hope to hear from you, and thank you for posting!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

Airport extreme unable to connect to new router

We just received a new router from our cable company. The old router worked with our airport extreme just fine. After hooking up the new router the airport extreme could not connect to it. I received the following error "error occurred while trying to access the apple wireless device. Make sure your connection is valid Error -6753" So then I tried to power off and reset the Airport extreme. The button was stuck on my reset button. I did figure that out and was able to click the button. But even if I would hear the audible click when i held down the reset button the amber light never flashed rapidly? Not sure what else to do. I have turned off the modem, unplugged the router, plugged them back in. etc. I just don't know where to go from here.
Thanks!
jodi

Were you able to get the AirPort Extreme to reset back to factory default settings, as LaPastenague detailed?
The amber light needs to flash rapidly for about 6-8 seconds during the process to indicate that the reset is taking place correctly. Once you release the reset button, the light will stay solid amber for 15-20 seconds or so, then change to slow blinking amber.
We are a bit confused as well, since in your first post you mention that you received a new router from the cable company, then later in the post, you mention that you have a (separate?) modem.
In the most recent post, you mention that you have a new modem. Is the new router from the cable company the same device as the new modem? Or, do you have a new modem and another new router in addition to the AirPort Extreme?
Can you clarify on exactly what devices that you have? Make and model numbers would help. We know that you have an AirPort A1408.

Can't reset incoming call during conversation after upgrade to IOS 5

Right after migration to IOS 5 I discovered that it's impossible to drop incoming call during conversation. I mean when you pressed power button twice in IOS 4 call must be transferred to voice mail or resetted. It was fine before migration to 5th version pf OS. I tried to reset my phone to manufacture settings but result was the same.
Does anyone met the same with new IOS?

Weird, I can't edit my messages here...
It doesn't matter once or twice the button was pressed - both calls are resetted.

Apple TV and a new router...

My Apple TV worked with the iPhone Remote app. (I lost the original Apple Remote during a move.) Then I got a new router. Remote app won't work according to teh guys at the Apple store because it communicates with the Apple TV through the wireless network and that info has changed. So they suggested I buy a new Apple remote because that will communicate directly with the Apple TV where I can enter the new router info. So I bought the Apple remote. Now the light blinks on the Apple TV when I press buttons on the new remote, but the Apple TV doesn't respond. When it starts up, it stalls trying to set the date and time and then goes to the screen saver. No response when I press MENU or try MENU and >|| as suggested in the online documentation. I have unplugged and reset the Cable modem, router, TV and Apple TV. Still no luck. Any ideas how I get to the menus in the Apple TV???

I get that, but my understanding is that the Apple remote should communicate directly with the Apple TV rather than through the network (this according to staff at the Apple store), and I have to get to the Apple TV menu system to set the location, etc.for the new router, right? But so far I have no way to get to those settings in the Apple TV.

Hp Photosmart not working with new router

My Hp Photosmart D110a will not work wirelessly with my new Netgear N600 router. This is the second new router I have tried. With the first one Belkin I could at least get it to print from my PCs. But never with my IPad. Now the printer will not print from anything. I have reset it, entered new passwords etc. spent hours on the phone with tech support. What to do now?

@Ann99, welcome to the forums
I understand your Photosmart D110a model is not working with your new router. I will gladly do my best to help you.
I have some questions and some things for you to try.
1. Is the printer connecting to the wireless network successfully when you run the wireless setup wizard from the printers front panel or is the printer not found when you are running the installation from your PC?
2. What did tech support determine the issue was when you called them?
3. Here are some guides for you to try, these 2 guides relate to the questions I had asked in the first question:
Unable to Connect to a Wireless Network When Using WEP Encryption and Shared Key Authentication
The Printer Is Not Found During a Wireless Network Installation
4. What Operating System are you running on your computer?
5. Where are you running the installation from (disk, download or HP Printer Install Wizard for Windows for Windows)?
Please let me know all of the information and results from your troubleshooting above!
Have a terrific day
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

New router can't get connection and can't find set up on macbook

I had to have a new router as i had problems with my internet solved internet problems but now my printer doesnt work unless i connect with usb cable, i have tried everything including deleting the printer, which now i have deleted the set up info off my macbook and can no longer install the printer please help it was working fine with my other router...

Hey , Welcome to the HP forums! I hope you enjoy your stay here. I see that you have replaced your router and are having some difficulties with connecting your Deskjet F4580 to the network. I can help you with that. As you are using Macintosh 10.7 I would recommend using a Windows PC to install the printer on and then to add to your wireless network. If that is not a practical option there are a couple of things we could try. Apple Software UpdateClick on your Apple Icon and go to Software Updates.Install any available updates.Download Apple's HP Printer drivers.If during the install there are no wireless options then:Go to your Apple icon, System Preferences, and Print and Scan.Double-click on the icon of your printer on the left side of this screen.In the pop up window click on Settings, Utility, and then Open Printer Utility.In this new window you should have a wireless tab along the top you can click on.On the left hand side we're looking for a wireless setup wizard.Run the wireless setup wizard to add the printer to your wireless network.Once the printer is connected remove the USB cable from the back of the printer.Go back to Apple, System Preferences, Print and Scan.Click on the plus button in the bottom left corner.Select your printer in this window.If there is a line that says Use that says Airprint click on that to select your printer from the list instead.Click on Add.Try printing.Ad-HocIf the above method does not allow you to connect the printer wirelessly then this may work.Perform a factory reset on the printer. I will include the directions on how to do that in a private message shortly.Turn the printer back on.Press the wireless button on the front of the printer.Wait about a minute.On your Mac or another wireless device you should see a network with a name similar to "HP Print XX Deskjet F4500" listed. Connect to that network.Press and hold the scan button (printer icon below the red x on the printer) for about ten seconds. When you release the printer should print a wireless test report.On the device you connected to the printer open a web browser and type the IP Address in the Address Bar exactly as it appears on the test report.You should have a Network tab along the top of this window.On the left side we are looking for a Wireless Setup Wizard.When you run that that should connect the printer to your wireless network.Once the printer is connected remove the USB cable from the back of the printer.If you connected your Mac to the printer above then reconnect the printer to your wireless network now.Go back to Apple, System Preferences, Print and Scan.Click on the plus button in the bottom left corner.Select your printer in this window.If there is a line that says Use that says Airprint click on that to select your printer from the list instead.Click on Add.Try printing.If this helps connect your printer to your wireless network then please let other forum users know by clicking on Accept as Solution below my post. Likewise if you have any other questions please let me know.I hope this helps and I hope you have a great day!

New router solved my Safari problems

This is just an FYI. I have had many of the problems with Safari (both v4 and v5) discussed here. Frequent hangs, occasional crashes, Flash crashing, etc, especially when visiting pages with Flash Content. Also, after a hang I would quit (or force quit) Safari, yet would still have temporary connectivity issues (e.g., unable to connect to internet through Safari, Firefox, dashboard, etc) that would last about 20 seconds before regular internet connectivity was restored. During this time, activity tracker wouldn't show any obvious processes that could account for this. However, I connect to the internet using a wireless router so this was one possibility.
I tried all the remedies chronicled here, including checking for add-ons/plug-ins, deleting plist, clearing Safari and Flash caches, deleting and reinstalling Flash, reinstalling Safari, open DNS, turning off DNS prefetching, etc. I struggled with this (and have been frustrated by it) for quite some time, and had almost given up on Safari. However, being an original Mac user (I remember being excited about upgrading my 128K to a 512K) I really didn't want to admit defeat.
Accessing Flash-rich pages through Safari seemed to cause the connectivity problems, but the problems seemed to persist even after quitting Safari. For this reason, I decided to try using a new wireless router. I had been using a Netgear WGR614v5 (from 2004), and I had updated the firmware. I now have a new router (Netgear WNDR3400, N600) and all of these problems are gone. The old router was otherwise working fine (on an older, non-Intel iMac, a Powerbook, my iPhone and a windoze machine running Windows 7) so the problem seems to be how Safari (or OS 10.6) interacts with the router or its driver. I can now relate to those who are very happy with Safari and its speed and reliability.
So if someone is having similar problems, perhaps this info could be useful. Or, if the problem was unique to just my machine, then (if nothing else) this was just a chance for me to vent.
Also, there are a few users on this forum who have been very helpful (even for a lurker). So a big shout-out to you folks (you know who you are) and the very patient help you provide here.

Ditto what Bee said!
That is just the kind of really useful information based on user experience we need more of in the forums!
Please feel free to keep it coming!

Error LNK1123: failure during conversion to COFF

hello,
I'm new to the sdk and I'm trying to open the sample projects to understand what's going on here,
the problem is that when i try to build the project(for example the SDK_File_Import project)
i get the error:
Error
1
error LNK1123: failure during conversion to COFF: file invalid or corrupt
why is that?
please help
thank you very much in advance
jony

Hello,
This topic is a bit old, but I have the same problem. My english isn't perfect so I don't understand everything in the pdf guide.
I just started, and I would like to build the Export project, which is in the Exemple directory. (I took the cs6 premiere pro release 2)
I did this part of the guide : "On Windows, to specify where you want the built plug-ins to go, set a user environment variable
(right-click My Computer > Properties > Advanced > Environment Variables > User variables)
called PREMSDKBUILDPATH to the desired path (e.g. “C:\Program Files\Adobe\Common\
Plug-ins\[version]\MediaCore\”)", and I also put the exemple directory on “C:\Program Files\Adobe\Common\Plug-ins\[version]\MediaCore\”.
Then, I opened the SDK_Exporter file with visual studio 2010 (from “C:\Program Files\Adobe\Common\Plug-ins\CS5\MediaCore\Examples\Projects\SDK_Exporter\"), and tried to debug it with the x64 debugger.
I obtained this error : "LINK : fatal error LNK1123: failure during conversion to COFF: file invalid or corrupt"
May someone help me to build this?
Thanks for your help!

I have an wireless printer and a new wifi router. I have set the printer and iPhone / iPad correctly to the new router but when i try to print it won't recognise the air printer. Help. All was working fine on my old router

I Have a new wifi router and have set up my iPad / iPhone and wireless printer correctly to the new router but I can't print from the iPad and iPhone. It keeps saying ' no AirPrint printer found'. Help please!

Start with the most basic thing that you can try. Unplug the router from power for about 30 seconds, and restart the printer and the iPad and plug the router back into power.

Can not connect All in one 209b to new router for wireless printing....

Have an HP laptop and All in one priner 209b. All was working fine, wired and wireless printing. Then we had to upgrade our ATT Uverse router. Everything works...even wireless laptop and printer when connected to laptop. However, can't get printer to printer wireless since it has the old router info. I used the disk but when it asks to you to pick the printer, I choose the printer but it says printer now found ??? what ???? and this is with the cable connected. I do not have the wizard on the touch screen but I did reset to factory settings hoping it would load new router info but it does not. How do you manually enter router into for wireless printing. Is it best to delete the printer and reinstall as new...wired and then wireless ???
I am about to call an outsite company and pay the outrageous charge as the help on HP is not working. Thanks

Try this utility:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02114394&cc=us&dlc=en&jumpid=reg_r1002_usen&lc=...
007OHMSS
I was a support engineer for HP.
If the advice resolved the situation, please mark it as a solution. Thank you.

HT201335 It got nA new router today and wanted to turn on apple tv but my remote app on iPad and iPhone will not recognize apple tv. Btw- I do not have apple tv remote.

It got A new router today and wanted to turn on apple tv but my remote app on iPad and iPhone will not recognize apple tv. Btw- I do not have apple tv remote.

It reboots it but unplugging can also rectify communication issues like this. A restore would be the next step.

HP 6520 won't scan with wireless connection and new router

My printer scanned fine before. Got a new internet provider=new router and now I can't scan scan anymore. The computer is connected wirelessly. The computer says it cannot communicate with the scanner. Same if I try from the printer front panel, it says it can't communicate with the computer.
The router seems like the obvious cuprit, but nothing in the router settings or manual suggest anything that could be blocking the scanner communications. The router firewall is turned-off.
Printing works fine, and I can connect to the printer through its IP address. The user interface can see the printer status, check ink levels, everything. Everything works but scanning. I've re-installed software multiple times, tried turning off firewalls and tried HP Scan and Print doctor. It's not much help.
I'm at wits end.
-ETC

Hello @etcottle , and welcome to the HP Forums!
I see you are experiencing scan connectivity issues. I would like to help!
I would recommend powering down your computer, disconnect the power cord from the printer and the power outlet, and remove the power from your router for 60 seconds.
After 60 seconds, plug the router back in. Once the router has begun broadcasting, plug the printer back in. Ensure you plug the printer directly to a wall outlet. Make sure to bypass any sort of surge protector or power bar.
After the printer is on, re-run the wireless setup.
I'd also suggest this document:
Wireless printing center Troubleshooting Issues
Good luck and please let me know the results of your troubleshooting steps. Thank you for posting on the HP Forums!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

My Macbook Pro 13' from 2011 keeps kicking me off the internet, even though my internet service (complete with brand new router) shows strong bars. Any help?!

I've had this 13 Inch Macbook Pro complete with the Lion since October 2011. I've been having trouble with the internet connection. I keep getting 'unable to connect to the internet' or 'website unavaiable'. We have a brand new router, so we know for certain the router isn't going out. Both of my parents computers connect just fine without getting kicked out. I thought maybe it was the seat, so I switched chairs and rooms and positions, but that doesn't seem to help. I check my internet connection and always says 'connected' with full bars. I've tried different browswers, using Safari and Google Chrome. It's frustrating not being able to get online and get kicked off in the middle of whatever you're doing for a reason you can't figure out. Any help/suggestions? It's been going on for a month or so now.

After biting the bullet and ordering more RAM, my computer now is working a ton better. So that must have been the main issue. With 8 GB RAM, I can now even run Parallels fluidly (better than my work PC!) where before simple things like logging in to my MBP after reboot could take forever.
The place I went to had several other people getting RAM upgrades at the same time as me, so between this and other comments I've seen in discussions here and elsewhere on the Internets, I take it to mean that either Apple should bump up the base RAM on its new machines, and/or stop charging so much for additional RAM.
I refused to believe a Pro machine bought with Lion installed would come with too little RAM for light to medium usage, but it was apparently the case. I'll mark this as a correct answer and hope some other poor soul will come across this thread and be helped by it.

Avoid Read New Routing during conversion in CO41

Similar Messages

Maybe you are looking for