Barcode Type 128 Mode C

Hi,
I have to create a barcode in type 128 with mode C to be printed via smartforms.
But when I create the new barcode in TA SE73, I can only use A, N, U. So how can I
create a barcode with Mode C? What is the meening of A, N and U?
Thank you!

Hi Michael,
I have exactly the same problem. Did you already find a suitable solution ?
Thanks,
Roque.

Similar Messages

Regarding Barcode Type....

Hi friends...
     How can I get the information about the attributes of different barcode types   used in Smartforms?
Kindly Suggest me the solution for this query???
Points will be rewarded to the useful answer...
Thanx,
Rahul.

Hi Rahul,
You can use barcodes types already created or you can create new one if
these types does not satisfy you requirement.
If you create a new system bar code for the "new bar code technology" in transaction SE73, you must specify the following parameters:
Bar code name (used in Smart Styles)
Short text for system bar code (documentation)
Bar code symbology:
    Code39
    Code128
    Interleaved 2of5
    PDF417
    Code93
This selection determines the technical bar code type that is used to format the bar code data (also called bar code symbology). The symbology also determines which characters are allowed in the bar code data.
Bar code alignment:
Normal (that is, the scan direction is "from left to right")
Rotated (the scan direction is rotated by 90 degrees "from top to bottom")
Inverted (the scan direction is rotated by 180 degrees "from right to left")
Bottom-up (the scan direction is rotated by 270 degrees "from bottom to top")
Code39 ******************
Code39 is an alphanumeric code that can represent the following characters in the bar code data:
Numbers:        1234567890
Capital letters: ABCDEFGHIJKLMNOPQRSTUVWXYZ
Special characters: - . $ / + %
Blank characters (space characters)
The start and stop character for the Code39 bar code is usually represented by an asterix (*) in the text view of the bar code data (also called "human-readable text" or "interpretation line").
Parameters for Code39:
Narrow module width
Value range: 1 to 10
This is the width for the narrowest module of a bar code, measured in pixels. It controls the width of the bar code. Value 1 generates the "narrowest", value 10 the widest bars or spaces.
Linear height
Value range: 1 to 9999
Controls the height of the bars of the bar code, measured in pixels. A value of 600 is equal to a height of one inch.
Mod-43 check digit
Value range: X equals YES, blank character equals No
With this indicator, you can determine whether a Modulo-43 check digit is to be generated.
Bar ratio
Value range: 20 to 30
This value controls the ratio between wide and narrow bars. This value controls the ratio between wide and narrow bars.Value 20 means a ratio of 2.0:1, value 30 means a ratio of 3.0 to 1 (that is, 3:1).
Parameters for Interleaved 2of5:
Narrow module width
Value range: 1 to 10
This is the width for the narrowest module of a bar code, measured in pixels. It controls the width of the bar code. Value 1 generates the "narrowest", value 10 the widest bars or spaces.
Linear height
Value range: 1 to 9999
Controls the height of the bars of the bar code, measured in pixels. A value of 600 is equal to a height of one inch.
Mod-10 check digit
Value range: X equals YES, blank character equals No
With this indicator, you can determine whether a Modulo-10 check digit is to be generated.
Bar ratio
Value range: 20 to 30
This value controls the ratio between wide and narrow bars. This value controls the ratio between wide and narrow bars.Value 20 means a ratio of 2.0:1, value 30 means a ratio of 3.0 to 1 (that is, 3:1).
Code 128 *****************
Code128 is an alphanumeric code that can encode three different character sets. Each of the three character sets can represent 106 different characters. Within a bar code, you can alternate between the character sets.
The three Code128 character sets are named as follows:
Subset A) (contains, for example, digits, capital letters and control characters)
Subset B) (contains, for example, digits, uppercase and lowercase letters)
Subset C) (digit pairs from 00 to 99)
Parameters for Code128:
Narrow module width
Value range: 1 to 10
This is the width for the narrowest module of a bar code, measured in pixels. It controls the width of the bar code. Value 1 generates the "narrowest", value 10 the widest bars or spaces.
Linear height
Value range: 1 to 9999
Controls the height of the bars of the bar code, measured in pixels. A value of 600 is equal to a height of one inch.
Code128 mode
Value range: N (default value), A, U
In default mode N (None), the Code128 bar code works in subset B. If you want to switch to another subset, you must trigger the change explicitly with a control command ("invocation code") in the bar code data.
In mode A (automatic), the software analyzes the transferred bar code data and recognizes automatically which subset is the most adequate for the bar code data. Subsets are swapped automatically in the bar code data. A sequence of four or more digits initiates an automatic change in subset C.
In mode U (UCC case mode), you must transfer 19 digits in the bar code data. Subset C is set automatically and an FNC1 character is added as prefix.
Note: If fewer than 19 digits are transferred, the bar code is filled with zeros to the left until it contains 19 digits.
UCC check digit
Value range: X equals YES, blank character equals No
Note: This parameter has no effect becaues Code128 always generates a check digit, even in UCC mode. The parameter will be removed in the future.
Code93 is an alphanumeric code that can represent the following characters directly in the bar code data:
Numbers:        1234567890
Capital letters: ABCDEFGHIJKLMNOPQRSTUVWXYZ
Special characters: - . $ / + %
Blank characters (space characters)
The start and stop characters in the Code93 bar code are represented as # sign in the text view of the bar code data (also called "human-readable text" or "interpretation line").
Parameters for Code93:
Narrow module width
Value range: 1 to 10
This is the width for the narrowest module of a bar code, measured in pixels. It controls the width of the bar code. Value 1 generates the "narrowest", value 10 the widest bars or spaces.
Linear height
Value range: 1 to 9999
Controls the height of the bars of the bar code, measured in pixels. A value of 600 is equal to a height of one inch.
Check digit
Value range: X equals YES, blank character equals No
With Code93 bar codes, a pair of check digits is always used and is always generated in the bar code. This parameter has no effect.
PDF417 is a two-dimensional bar code to represent datasets that are larger as the usual datasets in one-dimensional bar codes (for example, more than 1,000 characters). The entire 7-Bit ASCII character set is generally processed (binary values 1 - 127, the value 0 is not permitted).
A PDF417 bar code consists of 3 to 90 consecutive rows. Every row consists of a start/stop indicator and "code words". A code word consists of 4 bars and 4 spaces. The minimum number of code words per row is three.
Parameters for PDF417:
Narrow module width
Value range: 1 to 10
This is the width for the narrowest module of a bar code, measured in pixels. Value 1 generates the "narrowest", value 10 the widest bars or spaces.
Linear height
Value range: 1 to 9999
This parameter currently has no effect on PDF417. The height of a PDF417 symbol is controlled by parameter "Single Row Height" and the number of columns and rows, in conjunction with the length of text data to be encoded.
Single row height
Value range: 1 to 32000
This value, multiplied by the narrow module width, returns the height of the individual rows of a PDF417 symbol, measured in pixels. Caution: Do NOT use the value 1 for this parameter
Security level
Value range: 0, 1-8
This parameter controls the number of code words that are generated for error recognition and error correction. The default value 0, however, only permits error recognition but no automatic correction. If you increase the security level, the level of error correction increases with it (this increases the size of the bar code).
Number of columns
Here, you can define the number of the code word columns which you can use to check the width of the bar code.
Value range:
0 (default value) : A row/column ratio of 1:2 is used.
Permitted values: 1 to 30
Number of rows
Here, you can define the number of rows which can be used to check the height of the bar code.
Value range:
0 (default value) : A row/column ratio of 1:2 is used.
Permitted values: 3 to 90
For example: If you leave both parameters set to the default value 0, the system would convert 72 code words in a bar code symbol with 6 columns and 12 rows.
Truncation
Value range: X equals YES, blank character equals No
This indicator determines if the right row indicator and the stop pattern are to be truncated (this saves space).
The following character combinations in the transferred bar code data have the special function:
\&    - This represents the end of a line (Carriage Return + Newline)
    - This represents a backslash (5C hexadecimal)
\0xYY - This represents a single byte with the value YY (hexadecimal)
        For example: \0x1E is output as a single byte with the value 1E (hex)
        or 30 (decimal).
The souce for this information is OSS Note 645128.
Still if u face any problem feel free to ask.
Regards,
Vivek
-Reward if useful

Code a bare de type 128

Bonjour
j'ai des problèmes lors de la lecture des code à barres de types 128 je suis parvenu à lire des codes de types EAN13 cependant en passant à des codes de types 128 mon VI n'est pas parvenu à lire le code (j'ai bien sur changé le type de code dans IMAQ read code et adapté la nouvelle ROI)
j'attache là mon vi
De quoi ce problème parvient -il à votre avis?
merci d'avance
Pièces jointes :
code a barre image fixes.vi ‏37 KB

Bonjour Bou6,
Merci d'avoir posté sur le forum de National Instruments France.
Je suis heureux de voir que votre premier problème est résolu. Si tout est OK, pourriez vous mettre votre post du 04/08 comme résolu? Merci d'avance.
Venons en à votre problème, votre ROI est normalement plus compliqué à décrypter en EAN 13 qu'en 128 donc vous avez fait le plus dur.
Voici des petites questions pour être sur d'avoir cerné votre problème:
              - Quelle type de réponse obtenez vous après traitement?
              - Est-ce proche de la réalité?
              - Avez vous bien mis le Barcode Type: Code 128 à l'entrée de votre VI IMAQ read barcode?
              - Pourquoi ne mettez vous pas une commande plutôt qu'une constante (voir dans le VI ci joint)?
            - Pourriez vous éventuellement faire une capture d'écran sur le traitement d'un code 128 pour que nous puissions voir là ou le bât blesse?
Très Cordialement
P. Denis
National Instruments
Pierre_D
National Instruments France
#adMrkt{text-align: center;font-size:11px; font-weight: bold;} #adMrkt a {text-decoration: none;} #adMrkt a:hover{font-size: 9px;} #adMrkt a span{display: none;} #adMrkt a:hover span{display: block;}
LabVIEW Tour
Journées Techniques dans 10 villes en France, du 4 au 20 novembre 2014
Pièces jointes :
code a barre image fixes type 128.zip ‏28 KB

New barcode type

I want to print Barcode type Code 128 Width 4cm and Height 1cm. I checked SE73. I don't find there. I tried to create one on my own and it is not working.
Any suggestions to make it work.
Thank you,
AP

hi,
as for reference i did the same and it is working fine for me...
pls check that smartstyle character format is activated and u assign this characterformat to the variable to print as barcode.
if it works with standard barcode then try to create one for zbarcode for reference.
se73--> system barcodes --> create..
Regards
CNU

Adding Barcode Type 39 (3 of 9) in Reader

Hi,
Does reader support barcode type 39 (3 of 9)? Is it just a font that's written into reader or an image that's inserted in the pdf? We need the barcode to be 300 dpi and bi-tonal.
Any recommendations on a recommended barcode creator that works best with Adobe Reader?

thank you for the quick reply
At time of pdf creation can we add a barcode - is it just a font or an image that's entered it?
I'm not sure if PDF supports barcodes when a pdf is created

Enterprise Content Management - Use of barcode type Code 39

Can anyone provide some insight on what barcoding types, other than UPC-A is compatible with SAP enterprise content management solutions? I have a potential client who likes the flexibility of Code 39.
Can it be used?
I look forward to your reply.

Hello Alton,
Here is the link for barcode type which are supported by SAP.
http://help.sap.com/saphelp_47x200/helpdata/en/d9/4a94e251ea11d189570000e829fbbd/frameset.htm
Hope this helps.
Regards
Arif Mansuri

Printing different barcode types..!

Hi Guys,
I have a requirement to print barcode of materials, the barcode type varies depends on the length of material No.
How this can be acheived in Adobe form ?
I am looking to control the visibility of the barcode through some conditions.
Also how I can loop through a internal table to print the barcode, which should each one in a separate page.
Thanks
Sam

It is a javascript-statement. IF you aren't familiar with javascript it is hard to develop a adobe-form at all.
My first case would be to make yourself familiar with the concept of Adobe-forms. You can work thorugh the getting started content provided by SAP and Adboe. There you will get a lot of basic experience on that tool itself and formclac/javascript.
Anyway, here is the JAvascript-example for the case you need to complete the solution:
switch(this.yourfield_barcodetype.value)
case "A":
execute code block 1
case "B":
execute code block 2
default:
code to be executed if n is different from case 1 and 2

Barcode code 128 scanning problem

Hi,
I am using a code 128 type barcode in smartforms and
   currently I am working on ECC 6.0.
Bar Code Symbology   Code 128
Bar Code Alignment   Normal
Narrow Module Width 09
Linear Height        00130
Code128 Mode:        A
Bar Code Symbology   Code 128
Bar Code Alignment   Normal
Narrow Module Width 09
Linear Height        00300
Code128 Mode:        A
But scanner is unable to read the barcodes eventhough i tried playing with the width and height of barcode.
Pls. let me know how to fix this issue.
Thanks.

Hi,
I have a similar setup. I'm having problem with the width of the barcode. Even if the setup is 1 cm height and 4cm. In preview it is showing correctly but once it is printed the width is only 2.3 cm.
Any idea what is wrong?

Barcode CODE 128 with large number (being rounded?) (BI / XML Publisher 5.6.3)

After by applying Patch 9440398 as per Oracle's Doc ID 1072226.1, I have successfully created a CODE 128 barcode.
But I am having an issue when creating a barcode whose value is a large number. Specifically, a number larger than around 16 or so digits.
Here's my situation...
In my RTF template I am encoding a barcode for the number 420917229102808239800004365998 as follows:
<?format-barcode:420917229102808239800004365998;'code128c'?>
I then run the report and a PDF is generated with the barcode. Everything looks great so far.
But when I scan the barcode, this is the value I am reading (tried it with several different scanner types):
420917229102808300000000000000
So:
Value I was expecting: 420917229102808239800004365998
Value I actually got: 420917229102808300000000000000
It seems as if the number is getting rounded at the 16th digit (or so, it varies depending of the value I use).
I have tried several examples and all seem to do the same. But anything with 15 digits or less seems to works perfectly.
Any ideas?
Manny

Yes, I have.
But I have found the cause now.
When working with parameters coming in from the concurrent manager, all the parameters define in the concurrent program in EBS need to be in the same case (upper, lower) as they have been defined in the data template.
Once I changed all to be the same case, it worked.
thanks for the effort.
regards
Ronny

New BarCode Type to print Brazil Boleto forms

Hi
We have requirement to print BOLETO form with Bar Code for Citi Bank Brazil. As per Citi Bank manual provided, we need to print the Bar Code with bar code type "INTERCALATED type 2 of 5".
But in SAP, when we create new custom bar code(ex. ZBAR2) using SE73, we are not finding the above said bar code type.
The nearest match is 2OF5 ( Bar Code ITERLEAVED 2 OF 5). We used this, but the output of bar code printed is not upto the expectation.
Please can someone help on how to bring/install the new bar code type INTERCALATED in SAP.
Thanks in advance.

hi,
as for reference i did the same and it is working fine for me...
pls check that smartstyle character format is activated and u assign this characterformat to the variable to print as barcode.
if it works with standard barcode then try to create one for zbarcode for reference.
se73--> system barcodes --> create..
Regards
CNU

Barcode fonts 128 and 39 "shrink" when exported to PDF

Hello,
Crystal reports recommends using either IDAutomation or Azalea barcode fonts for reports.
We are using IDAutomation. Both the 128 and the 39 encoded fonts work fine when
printing. However when we export to a PDF file the fonts "shrink" down to a tiny box and
are both un-scannable and nearly invisible.
At this point in time, does anyone know of any fonts that can be used in v.XI which can
be exported to PDF and be scannable? We are using the RDC and so are stuck with v.XI.
Is the highest service pack for R1 (I believe it is SP4) of any help with this issue?
If you know if answers to the above are negative please respond anyway.
Also, I you know of any threads which deal with the "incredible shrinking font" issue,
please mention them.
Thank you,
Joe

HI, Joe;
The previous post was for the incorrect verison of Crystal Reports from what you are using.
Have a look at this Note referring to Crystal Reports XI R1:
[ForceLargerFonts|https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/oss_notes_boj/sdn_oss_boj_erq/sap(bD1lbiZjPTAwMQ==)/bc/bsp/spn/scn_bosap/notes%7B6163636573733d36393736354636443646363436353344333933393338323636393736354637333631373036453646373436353733354636453735364436323635373233443330333033303331333233313338333733353333%7D.do|Note 1218753]
Regards,
Jonathan

Two barcode types in one barcode

Code 128 set B and code 128 set C should be printed 'as one barcode'.
In the data the beginning of line should be printed as code 128 b and the rest of the line as code 128 c.
An example of data: JJFI00050011117139369
The first characters: JJFI0 => print in code 128 b
The rest: 0050011117139369 => print in code 128 c
This is needed due to space limitations on the print form.
Can anybody help me in this matter?
(My Adobe Output Designer version is 5.5.0.317)

If you refuse to separate the field or if two unique bar code fields produces unusable results then I believe you are out of luck.
Without stop & start codes I don't understand how software would be able to read it.
Central can do a lot of great stuff but it is a bit stodgy when it comes to customization. When it comes to bar codes they are "fixed" in size, probably matching the specifications for the bar code. Unlike other software you can't even stretch the field to increase the size. There is some customization available by modifying the ICS file but it doesn't appear to be anything near what you want. Check out any of the "barcode*.* files. The begining of every file shows what can be changed and what the values mean.

Event Type Descriptions - Mod Wheel / Quick Access Auto Help

I really just need some description for the possible event types you can assign to controllers in logic, like the mod wheel. For example, expression, portamento time... I don't know what i should be listening for when it comes to utilizing these controls. But I know some of these options would greatly enhance my samples (EWQLSO) in terms of reality (strings swelling instead of remaining stagnant). The manual mentions around 15 event types, and I was wondering if I could get some solid definitions. Some are obvious, but feel free to fill in the gaps, it would be much appreciated.
Also, I've had some trouble getting mod-wheel movement to show up in multiple windows in logic. Even if I do automation quick access assigned to the mod wheel, I get split information. For instance, the Arrange Window will record pitch bend data, but it will not be reflected in the Event List, or Editor, let alone these options in the Matrix window.
Any help would be great.

Please don't cross-post. It is considered very rude to do that here:
http://forum.java.sun.com/thread.jspa?threadID=5233033&messageID=9953169#9953169

Printing barcodes in ActiveX mode

Hello,
I'm using CR 13 for VS 2010 and ASP.NET 4.
I have some reports with barcodes. When I export the report to PDF then print - everything is OK, the barcodes are printed correctly.
But if I use the ActiveX printing directly to printer - the barcodes are not printed, only numbers.
The printer is the same.
What might be a reason for this?
Thank you.

I think I've found the problem.

Printing barcode EAN 128

Hello.
I need print barcode using EAN128. I saw that for EAN128 exist barcode BC_EANH. When I use it on print preview I have barcode but when I print it I got number but not barcode (laser printer, pdf printer)
Should I print that barcode on barcode printer? or I should use another barcode
Thanks in advance,
Edward

Hello,
Perhaps this webservice is useful for you; http://www.gs1-label.com
You can use the public account to try the O2L WEBservices demo:
e-mail address; anonymous(at)t2s.nl - password; o2lweb
The label generated in PDF, easy to print on a 'normal' printer, is certified by GS1.
Please note that this is an example, the webservice supports other barcode symbologies as well and labels can also be generated as ZPL (Zebra label printer).
O2L WEBservices exposes its technology by through web standards (SOA). Implementing the services is therefore easy and quick. A hands-on example of O2L WEBservices working in combination with SAP NetWeaver Visual Composer is available.
Best regards,
Judith de Witte

Barcode Type 128 Mode C

Similar Messages

Maybe you are looking for