Belkin Flip KVM Switch and Blue Screen

G5 Dual 2ghz, clean install of Leopard.
I have a dual head video card, attached to the DVI port is a 22" monitor connected via DVI, on the ADC port I have ADC to VGA adaptor which a Belkin "Flip" KVM switch is attached, leading to a 17" monitor.
On booting I get to the point when the Finder should be loading and get a blue screen on both monitors, the monitors both periodically do a fade from black as though the system has just tried to change video resolution. However this loop continues.
If I remove the KVM and have the 17" plugged in, boot up is fine. This set up worked fine with 10.4x.
Any suggestions.
Thanks

Zork, have you cracked this problem yet?
I have a similar item - Belkin's Switch2 for Mac mini - and I get the same halting at the blue screen. Belkin UK's 2nd line support failed to replicate this error and replaced my device with the one that they used. It failed as well on my system (which works fine without the Switch2!).
In case it helps, a dig in the logs showed the following fault repeating itself presumably while the screen stayed blue:
(starts 6 lines down, I think)
01/05/2009 10:12:25 com.apple.SystemStarter[29] kextload: /Library/Extensions/VBoxDrv.kext loaded successfully
01/05/2009 10:12:25 com.apple.SystemStarter[29] Loading VBoxUSB.kext
01/05/2009 10:12:25 com.apple.SystemStarter[29] kextload: /Library/Extensions/VBoxUSB.kext loaded successfully
01/05/2009 10:12:25 com.apple.SystemStarter[29] Loading VBoxNetFlt.kext
01/05/2009 10:12:25 kernel vboxdrv: fAsync=0 offMin=0x1230 offMax=0x39450
01/05/2009 10:12:25 kernel VBoxDrv: version 2.1.4 r42893; IOCtl version 0xa0009; IDC version 0x10000; dev major=18
01/05/2009 10:12:25 ReportCrash[110] Formulating crash report for process WindowServer[68]
01/05/2009 10:12:25 com.apple.SystemStarter[29] kextload: /Library/Extensions/VBoxNetFlt.kext loaded successfully
01/05/2009 10:12:26 com.apple.launchd[1] (com.apple.WindowServer[68]) Exited abnormally: Floating point exception
01/05/2009 10:12:26 kernel VBoxFltDrv: version 2.1.4 r42893
01/05/2009 10:12:27 kernel AirPort: Link Up on en1
01/05/2009 10:12:28 ReportCrash[110] Formulating crash report for process WindowServer[116]
01/05/2009 10:12:28 com.apple.launchd[1] (com.apple.WindowServer[116]) Exited abnormally: Floating point exception
01/05/2009 10:12:28 com.apple.launchd[1] (com.apple.WindowServer) Throttling respawn: Will start in 9 seconds
01/05/2009 10:12:30 ReportCrash[110] Saved crashreport to /Library/Logs/CrashReporter/WindowServer2009-05-01-101214GottaLight-2.crash using uid: 0 gid: 0, euid: 0 egid: 0
01/05/2009 10:12:30 ReportCrash[110] Saved crashreport to /Library/Logs/CrashReporter/WindowServer2009-05-01-101227GottaLight-2.crash using uid: 0 gid: 0, euid: 0 egid: 0
01/05/2009 10:12:38 ReportCrash[121] Formulating crash report for process WindowServer[120]
...and repeats it every 9-10 seconds.
Do/did you get this as well?
Can anybody comment on what is going on, please?

Similar Messages

Can Motion 5 replace a green screen and blue screen in the same shot?

Can Motion 5 replace a green screen and blue screen in the same shot? I would like to replace a green screen with one image, and a blue screen with another.

Fox gives a good example for keying green & blue (or any other color) from the same shot. I'd suggest doing a few things to get better accuracy.
First, the motion keyer always removes the color it detects the most of by default (blue/green). You can override this by setting the Strength parameter to zero, then use the Color sample tool to select the color you want. The advantage is motion will do a good job of targeting only the hue (color) that you want to remove and set an appropriate starting softness. It also will remove spill based on this color. Looking at Fox's example movie and the shot, I'd approach the same shot this way:
Remove the Blue
1. Apply the keyer and set the strength to zero.
2. Use the Sample Color tool and select the blue (or other color) to be removed.
3. Decrease the spill level (if needed). In Fox's example the spill from the blue glasses is going to be minimal, especially compared to the green screen, your shot may need different adjustments. Only de-spilling what you need to will give you more accurate color right away and minimize additional color correction that might be needed later.
4. Use the Color selection tools (Chroma wheel/Luma bar) to fine tune. Ideally you want a minimal tolerance, the inner selection, with a nice fall off, the outer selection. Try with the Scrub boxes setting first, then switch to manual if you need more control. Again see Fox's example.
Remove Green
It's the same as the blue, you could apply the keyed to the same clip or a parent group, at this point it's many user preference.
With these techniques you can remove any color from a shot or create a mask based on a color. BTW, as you are learning to use the keyer I'd highly recommend having the Color Selection open so you can see the graphs. These give you real time feedback as you make selections and changes with the Strength, Refine and Color selection tools. Watch what happens as you make selection or changes, sometimes the problem area is actually in the brightness not the color, or the softness may change more than the tolerance selection. Observing what is happening in these graphs will help you figure out wha to change and speed things up.

I am getting frequent lock-ups and blue screens during boot up. The lock ups occur during normal use and I cannot click anything or force quit. The cursor shows something is loading, but never stops. I have to use power button. Ideas?

I am getting frequent lock-ups and blue screens during boot up on my Mac Pro. The lock- ups occur sometimes during normal use and I cannot click anything or force quit. The cursor shows something is loading, but never stops. I have to use power button.
I had the Mac Defender malware and I have used apple jack but still having issues.

I am getting frequent lock-ups and blue screens during boot up on my Mac Pro. The lock- ups occur sometimes during normal use and I cannot click anything or force quit. The cursor shows something is loading, but never stops. I have to use power button.
I had the Mac Defender malware and I have used apple jack but still having issues.

Dmp file and blue screen error Windows 7

Hi,
Just wondering if someone can tell me how to read the dmp file created after the blue screen appears ?
I have just recently upgraded my Toshiba P300 from Vista 64 bit to Windows 7 Home Prem 64 bit.
I dont know why Windows 7 keeps crashing and so far I have no idea of how to open the .dmp
file (I have zipped the dmp file and attahced below).
http://cid-7a99d6152c55359c.skydrive.live.com/self.aspx/.Public/minidump/022710-26223-01.zip
The message that I been given so far says :
Problem signature:
Problem Event Name:                        BlueScreen
OS Version:                                          6.1.7600.2.0.0.768.3
Locale ID:                                             3081
Additional information about the problem:
BCCode:                                               a
BCP1:                                                    FFFFF6FC40052000
BCP2:                                                    0000000000000002
BCP3:                                                    0000000000000000
BCP4:                                                    FFFFF80002E62322
OS Version:                                          6_1_7600
Service Pack:                                       0_0
Product:                                               768_1
Files that help describe the problem:
C:\Windows\Minidump\022710-26223-01.dmp
C:\Users\Caroline\AppData\Local\Temp\WER-125393-0.sysdata.xml

I have try step 1 and didnt boot up the window normaly...same thing happened
Window 7 is loading...then boom the screen failed and blue screen appear...
there is the latet crash report
Version=1
EventType=BlueScreen
EventTime=129810543666556864
ReportType=4
Consent=1
ReportIdentifier=9fb6a978-99f3-11e1-9b67-fa9a72be4846
IntegratorReportIdentifier=050912-14508-01
Response.type=4
DynamicSig[1].Name=OS Version
DynamicSig[1].Value=6.1.7601.2.1.0.256.1
DynamicSig[2].Name=Locale ID
DynamicSig[2].Value=3084
UI[2]=C:\Windows\system32\wer.dll
UI[3]=Windows has recovered from an unexpected shutdown
UI[4]=Windows can check online for a solution to the problem.
UI[5]=&Check for solution
UI[6]=&Check later
UI[7]=Cancel
UI[8]=Windows has recovered from an unexpected shutdown
UI[9]=A problem caused Windows to stop working correctly. Windows will notify you if a solution is available.
UI[10]=Close
Sec[0].Key=BCCode
Sec[0].Value=a
Sec[1].Key=BCP1
Sec[1].Value=0000000000000000
Sec[2].Key=BCP2
Sec[2].Value=0000000000000002
Sec[3].Key=BCP3
Sec[3].Value=0000000000000001
Sec[4].Key=BCP4
Sec[4].Value=FFFFF8000308BB7E
Sec[5].Key=OS Version
Sec[5].Value=6_1_7601
Sec[6].Key=Service Pack
Sec[6].Value=1_0
Sec[7].Key=Product
Sec[7].Value=256_1
File[0].CabName=050912-14508-01.dmp
File[0].Path=050912-14508-01.dmp
File[0].Flags=589826
File[0].Type=2
File[0].Original.Path=C:\Windows\Minidump\050912-14508-01.dmp
File[1].CabName=sysdata.xml
File[1].Path=WER-27253-0.sysdata.xml
File[1].Flags=589826
File[1].Type=5
File[1].Original.Path=C:\Users\Moz\AppData\Local\Temp\WER-27253-0.sysdata.xml
File[2].CabName=Report.cab
File[2].Path=Report.cab
File[2].Flags=196608
File[2].Type=7
File[2].Original.Path=Report.cab
FriendlyEventName=Shut down unexpectedly
ConsentKey=BlueScreen
AppName=Windows
AppPath=C:\Windows\System32\WerFault.exe
ive also have got a AI SUITE II crash...
Version=1
EventType=APPCRASH
EventTime=129809041249476693
ReportType=2
Consent=1
UploadTime=129809041250516752
ReportIdentifier=ddea075d-9895-11e1-9a9f-eb38eba38a41
IntegratorReportIdentifier=ddea075c-9895-11e1-9a9f-eb38eba38a41
WOW64=1
Response.BucketId=2555721005
Response.BucketTable=1
Response.type=4
Sig[0].Name=Application Name
Sig[0].Value=AI Suite II.exe
Sig[1].Name=Application Version
Sig[1].Value=1.0.0.40
Sig[2].Name=Application Timestamp
Sig[2].Value=00000000
Sig[3].Name=Fault Module Name
Sig[3].Value=KERNELBASE.dll
Sig[4].Name=Fault Module Version
Sig[4].Value=6.1.7601.17651
Sig[5].Name=Fault Module Timestamp
Sig[5].Value=4e211319
Sig[6].Name=Exception Code
Sig[6].Value=0eedfade
Sig[7].Name=Exception Offset
Sig[7].Value=0000b9bc
DynamicSig[1].Name=OS Version
DynamicSig[1].Value=6.1.7601.2.1.0.256.1
DynamicSig[2].Name=Locale ID
DynamicSig[2].Value=3084
DynamicSig[22].Name=Additional Information 1
DynamicSig[22].Value=0a9e
DynamicSig[23].Name=Additional Information 2
DynamicSig[23].Value=0a9e372d3b4ad19135b953a78882e789
DynamicSig[24].Name=Additional Information 3
DynamicSig[24].Value=0a9e
DynamicSig[25].Name=Additional Information 4
DynamicSig[25].Value=0a9e372d3b4ad19135b953a78882e789
UI[2]=C:\Program Files (x86)\ASUS\AI Suite II\AI Suite II.exe
UI[3]=AI Suite II has stopped working
UI[4]=Windows can check online for a solution to the problem.
UI[5]=Check online for a solution and close the program
UI[6]=Check online for a solution later and close the program
UI[7]=Close the program
LoadedModule[0]=C:\Program Files (x86)\ASUS\AI Suite II\AI Suite II.exe
LoadedModule[1]=C:\Windows\SysWOW64\ntdll.dll
LoadedModule[2]=C:\Windows\syswow64\kernel32.dll
LoadedModule[3]=C:\Windows\syswow64\KERNELBASE.dll
LoadedModule[4]=C:\Windows\syswow64\WINTRUST.DLL
LoadedModule[5]=C:\Windows\syswow64\msvcrt.dll
LoadedModule[6]=C:\Windows\syswow64\CRYPT32.dll
LoadedModule[7]=C:\Windows\syswow64\MSASN1.dll
LoadedModule[8]=C:\Windows\syswow64\RPCRT4.dll
LoadedModule[9]=C:\Windows\syswow64\SspiCli.dll
LoadedModule[10]=C:\Windows\syswow64\CRYPTBASE.dll
LoadedModule[11]=C:\Windows\SysWOW64\sechost.dll
LoadedModule[12]=C:\Windows\syswow64\ADVAPI32.DLL
LoadedModule[13]=C:\Windows\system32\VERSION.DLL
LoadedModule[14]=C:\Windows\WinSxS\x86_microsoft.windows.common-controls_6595b64144ccf1df_5.82.7601.17514_none_ec83dffa859149af\COMCTL32.DLL
LoadedModule[15]=C:\Windows\syswow64\GDI32.dll
LoadedModule[16]=C:\Windows\syswow64\USER32.dll
LoadedModule[17]=C:\Windows\syswow64\LPK.dll
LoadedModule[18]=C:\Windows\syswow64\USP10.dll
LoadedModule[19]=C:\Windows\system32\MSIMG32.DLL
LoadedModule[20]=C:\Windows\syswow64\SHELL32.DLL
LoadedModule[21]=C:\Windows\syswow64\SHLWAPI.dll
LoadedModule[22]=C:\Windows\syswow64\OLE32.DLL
LoadedModule[23]=C:\Windows\syswow64\OLEAUT32.DLL
LoadedModule[24]=C:\Windows\system32\IMM32.DLL
LoadedModule[25]=C:\Windows\syswow64\MSCTF.dll
LoadedModule[26]=C:\Windows\system32\CRYPTSP.dll
LoadedModule[27]=C:\Windows\system32\rsaenh.dll
LoadedModule[28]=C:\Windows\syswow64\imagehlp.dll
LoadedModule[29]=C:\Windows\system32\ncrypt.dll
LoadedModule[30]=C:\Windows\system32\bcrypt.dll
LoadedModule[31]=C:\Windows\SysWOW64\bcryptprimitives.dll
LoadedModule[32]=C:\Program Files (x86)\ASUS\AI Suite II\AsMultiLang.dll
LoadedModule[33]=C:\Windows\system32\WINSPOOL.DRV
LoadedModule[34]=C:\Program Files (x86)\ASUS\AI Suite II\ImageHelper.dll
LoadedModule[35]=C:\Windows\WinSxS\x86_microsoft.windows.gdiplus_6595b64144ccf1df_1.1.7601.17514_none_72d18a4386696c80\gdiplus.dll
LoadedModule[36]=C:\Windows\system32\USERENV.dll
LoadedModule[37]=C:\Windows\system32\profapi.dll
LoadedModule[38]=C:\Windows\system32\GPAPI.dll
LoadedModule[39]=C:\Windows\system32\cryptnet.dll
LoadedModule[40]=C:\Windows\syswow64\WLDAP32.dll
LoadedModule[41]=C:\Windows\system32\SensApi.dll
LoadedModule[42]=C:\Windows\system32\Cabinet.dll
LoadedModule[43]=C:\Windows\system32\DEVRTL.dll
LoadedModule[44]=C:\Windows\system32\WindowsCodecs.dll
LoadedModule[45]=C:\Windows\system32\WINHTTP.dll
LoadedModule[46]=C:\Windows\system32\webio.dll
LoadedModule[47]=C:\Windows\syswow64\WS2_32.dll
LoadedModule[48]=C:\Windows\syswow64\NSI.dll
LoadedModule[49]=C:\Windows\system32\credssp.dll
LoadedModule[50]=C:\Windows\syswow64\mswsock.dll
LoadedModule[51]=\\.\globalroot\systemroot\syswow64\mswsock.dll
LoadedModule[52]=C:\Windows\syswow64\WININET.dll
LoadedModule[53]=C:\Windows\syswow64\Normaliz.dll
LoadedModule[54]=C:\Windows\syswow64\iertutil.dll
LoadedModule[55]=C:\Windows\syswow64\urlmon.dll
LoadedModule[56]=C:\Windows\system32\Secur32.dll
LoadedModule[57]=C:\Windows\System32\wshtcpip.dll
LoadedModule[58]=C:\Windows\System32\wship6.dll
LoadedModule[59]=C:\Windows\system32\IPHLPAPI.DLL
LoadedModule[60]=C:\Windows\system32\WINNSI.DLL
LoadedModule[61]=C:\Windows\system32\dhcpcsvc6.DLL
LoadedModule[62]=C:\Windows\system32\dhcpcsvc.DLL
LoadedModule[63]=C:\Windows\syswow64\CFGMGR32.dll
LoadedModule[64]=C:\Windows\system32\uxtheme.dll
LoadedModule[65]=C:\Windows\system32\DNSAPI.dll
LoadedModule[66]=C:\Program Files (x86)\Bonjour\mdnsNSP.dll
LoadedModule[67]=C:\Windows\system32\rasadhlp.dll
LoadedModule[68]=C:\Windows\System32\fwpuclnt.dll
LoadedModule[69]=C:\Program Files (x86)\ASUS\AI Suite II\AssistFunc.dll
LoadedModule[70]=C:\Windows\system32\PROPSYS.dll
LoadedModule[71]=C:\Windows\WinSxS\x86_microsoft.windows.common-controls_6595b64144ccf1df_6.0.7601.17514_none_41e6975e2bd6f2b2\comctl32.dll
LoadedModule[72]=C:\Windows\system32\apphelp.dll
LoadedModule[73]=C:\Windows\syswow64\CLBCatQ.DLL
LoadedModule[74]=C:\Windows\system32\wpdshext.dll
LoadedModule[75]=C:\Windows\system32\WINMM.dll
LoadedModule[76]=C:\Windows\System32\shdocvw.dll
LoadedModule[77]=C:\Windows\SysWOW64\ieframe.dll
LoadedModule[78]=C:\Windows\syswow64\PSAPI.DLL
LoadedModule[79]=C:\Windows\SysWOW64\OLEACC.dll
LoadedModule[80]=C:\Windows\syswow64\SETUPAPI.dll
LoadedModule[81]=C:\Windows\syswow64\DEVOBJ.dll
LoadedModule[82]=C:\Windows\system32\ntmarta.dll
LoadedModule[83]=C:\Program Files (x86)\ASUS\AI Suite II\pngio.dll
LoadedModule[84]=C:\Program Files (x86)\ASUS\AI Suite II\AsAcpi.dll
LoadedModule[85]=C:\Program Files (x86)\ASUS\AI Suite II\asacpiEx.dll
LoadedModule[86]=C:\Windows\system32\RpcRtRemote.dll
State[0].Key=Transport.DoneStage1
State[0].Value=1
State[1].Key=DataRequest
State[1].Value=Bucket=-1739246291/nBucketTable=1/nResponse=1/n
FriendlyEventName=Stopped working
ConsentKey=APPCRASH
AppName=AI Suite II
AppPath=C:\Program Files (x86)\ASUS\AI Suite II\AI Suite II.exe

IPad Air with iOS 8.02 freezes and blue screen appears. What should be done ? Why is this happening ?

IPad Air with iOS 8.02 freezes and blue screen appears. What should be done ? Why is this happening ?

If nothing else works, you might try this one. It has worked for many others ...
Use iTunes to do a reset to factory default condition. Always be sure to do your backups before fiddling with your iPad. You might do both the iCloud and the iTunes backup, just to be sure!
Back up and Restore your iOS Device with iCloud or iTunes
http://support.apple.com/kb/ht1766
iTunes: About iOS Backups
http://support.apple.com/kb/ht4946
Use iTunes to Restore your iOS Device to Factory Settings
http://support.apple.com/kb/ht1414
Various issues from many different users have been solved by this. I've lost count on how many have been helped by this, so far. But, it doesn't mean EVERYONE will be helped, but I've seen a whole lot. You can only try and see ...
iPad 2 and iOS 8.0.2 Problems
For all iPad 2 owners, this is an important solution for you! These problems result from long-term use, continuous upgrades, corrupted files and various glitches that happen over this long term use. You just need to get your iPad 2 back to FACTORY FRESH CONDITION to start out clean!
Here's one person's solution which will help a lot of iPad 2 users!
keithfrommariettaOct 12, 2014 3:25 PM Re: IPAD2 very slow after IOS 8 upgrade
Re: IPAD2 very slow after IOS 8 upgradein response to pacoKAS
SOLVED: IOS 8 Issues on iPad 2:
I just returned home from a visit to the Genius Bar. Like you and many others, when I upgraded my iPad 2 to IOS 8, it became practically unusable. It was VERY slow, lagged whenever trying to to do anything. Lots of screen freezes and apps spontaneously crashing. I was convinced that the processor on the iPad 2 just couldn't handle the new IOS and I went in to see about restoring to IOS 7.
Thankfully, I was hooked up with a very sharp guy at the bar. The problem is not with the OS, it is with it being an *upgraded* OS. He used the analogy of when you had an older Windows computer and how over time (and over upgrades), they just tended to get slower and slower because of all of the garbage that was carried forward in the upgrades. At those times (and if you've ever had a Windows computer, you get this), the only thing that would speed it up would be to wipe the machine and do a fresh install of the current OS and then reload your apps, and the viola, everything would be fast again. Well, it turns out that IOS can suffer the same problems.
THE FIX: FIRST, be sure you have a current iCloud backup of your device. Connect your iPad to a computer that has a clean fresh copy of IOS 8 on iTunes (this is best done with a computer other than the one that you sync your device to because you DO NOT want to restore it from a back up just yet). Ideally, if you do this at an Apple store you'll be assured of the right version there and someone to answer any questions you might have along the way. You then hold the power and home button down to hard-reset the device and continue to hold them down until it reboots into recovery mode. You then follow the instructions on the computer to reinstall the OS on the device (which wipes everything from it and then reinstalls a clean copy of it). Once this is done (which only takes about 15 minutes), your device will reboot and ask you to set it up. Answer the questions about language, location, etc. and continue until it asks you to log into your iTunes account. Once you do that, it will ask if you want to either 1) Set it up as a new device, 2) Restore from iCloud, or 3) Restore from iTunes. Choose (2), restore from iCloud. This will ensure that it brings down "clean" copies of all of your apps and preferences rather than the potentially corrupted ones that might reside in your iTunes backup. That's it! It will take a few hours depending on how much data and apps you have, but I am happy to report that my iPad 2 is now running IOS 8 and it's running as fast as it ever did when it was brand new!
To sum it up, this process 1) Wipes your device and the garbage causing your problems, 2) Loads a clean and bug-free version of IOS 8 to your device, and 3) restores your apps and data so that it looks just like it did before the wipe, with the exception that it works now! :-)
Note also that by following this process you don't have to go through the painful and laborious process of reloading all of your apps, data and/or settings. iCloud takes care of all of that for you.

Cropping and Blue Screening - 2 unrelated questions.

1) When I straighten a still in Canvas by using the wire frame, to make a house level, say, the cropping lines, naturally, move with it. So a cropping line at an angle will give me a slanting top and bottom line. So how can I crop it so that the picture has a square aspect? Is the only recourse to go back to the original site for the picture, GIMP or iPhoto, perhaps, crop it there and re-import the photo into FCE? Or is there a quicker way?
2) I have added a number of videos above my main video to show, for example, falling snow, and eliminated their black background by Modify - Composite Mode - Screen. Very easy and by no means unusual. So, my question, is, why all the fuss about green and blue screening? Setting it up seems troublesome. A black background for the purpose is much easier to make, and, for that matter, easier to find. I looked down my back yard this morning and this side of the creek are jet black bushes which would seem ideal for such a purpose. This seems such a no-brainer that I think I must be missing something. But it is curious.
Allosaurus

1) I shall immediately turn to the garbage matte section in your book - I'm sure I remember seeing one - and work it out from there. And here I always thought a garbage matte was that rug I bought in Cairo.
2) A black screen. That does give me a thought. When I return to my upcoming masterpiece, " "Orrible Murder at the Castle Doom" I could put one of my granddaughters in a black suit, photograph her against a black background and Voila! a floating head. I wonder if they give out Oscars for original ideas?
Once more. Thank you.
Allosaurus

Blank Black Screen And Blue Screen. Do I Need To Do Reflow To Ati Chipset?

Hello i want to tell you my problems and what i did until now.
I have hp pavilion dv3 4150st. I was using win7 64 bit . and i was geting an error that says "display driver amd driver stopped responding and has successfully recovered".I started to get this eror often . And a few days later my pc startet to get blue screen errcor after a few second later than display driver error. . And after 2-3 blue screen error i lost my screen. It was blank black . when i restart pc the screen was blank black. there was no image. When i started to fix another monitor, i saw screen . And i installed the win 7 with another external monitor. Bu i had still black screen after install the windows.. Itand was still black after i remove the ectgernal monitor. I installed bios again but i had still black screen. And i tried the install ati display driver after installing windows . But after i installed the display driver, i had the blue screen error again. And now i have still both blank black screen and blue screen problem.
I cleaned the motherboard. I resetted bios. I installed bios. i installed windows again. i installed ati display driver.But these couldnt solve the problems. Please can you tell me what can i do now ?

Hi beginner_2012,
Thank you for your post, I will do my best to assist you.
I grasp that you were getting the error "display driver amd driver stopped responding and has successfully recovered" quite often. Then a few days later you got the blue screen then the above error message, after 2 -3 more errors the screen is now blank or black. Here is a document to assist you with this. Troubleshooting Black Screen Displays with No Error Messages During Startup or Boot.
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

My ipnone 5s keeps crashing and blue screening any advice

My ipnone 5s keeps crashing and blue screening any advice

Basic troubleshooting from the User's Guide is reset, restart, restore (first from backup then as new). Try each of these in order until the issue is resolved.

Grey screen no apple followed by blue screen with vertical lines. Graphics and logic board replaced 6 months ago. What to do? I held down shift, it gets HOT HOT and makes noises. (for safety mode) followed by a blank grey screen and blue screen

grey screen no apple followed by blue screen with vertical lines. Graphics and logic board replaced <6 months ago. What to do? I held down shift, it gets HOT HOT and makes noises. (for safety mode) followed by a blank grey screen and blue screen. Then tried the other way (sorry, I think it's command alt delete? I don't remember) and it turned from grey (no apple symbol) to blue blank. Then third time, grey followed by blue with vertical lines, not blocky clear lines that you can see if you are close to it.
Thanks for any help!

You have to take the computer to the Apple store to have it checked out.
Genius Bar reservation
http://www.apple.com/retail/geniusbar/
Best.

X-Fi Titanium and Blu-Screen (Win XP)

%[ Hi ti all, i am a new user and, of course, i have my first big problem with creative drivers/software.
Before installation of audio card all worked greatly but after i get a blu screen at shut down or at reboot (is the same).
I used the latest version of the drivers available on the web (2.7.0006).
I removed audio card and drivers and all works greatly, too.
I reinstalled audio card + drivers and blu screen at shut down/reboot appears again.
Anyone knows the solution.
Audio card works correctly but with this blue screen ?the creative console don't save any settings, so every time
i turn on the pc i have to configure it (effect, mixer, number of speakers, mic amplifiers, etc. etc.).
Please help me.
This is my configuration:
Cpu Intel Core i7 920
M/b Asus P6T (bios 0603)
Ram 6 Gb DDR3 (3x2Gb DDR3 Corsair) ('cause i have Vista64 on another partition)
ATI Radeon HD4890 Gb?
HD Seagate 500 Gb
Thanks in advance.

Anyone?Message Edited by Rayman968 on 08-0-2009 2:47 PM

Gateway FX and Blue Screen of Death

Computer:
Gateway FX 7024
GeForce 8800GT 512 mb
Problem:
I've had the computer for 1 1/2 years with very few problems. Recently, the screen will lock up solid and be illegible with "static" lines all the way down the monitor. Sometimes before the screen locks up, it will flip to the blue screen of death, say it's dumping physical memory, and then lock up. Only thing I can do is restart, but it will do it again at random lengths of time. Happens more while I'm playing games than anything else. Sounds to me like the graphics card has gone Tango Uniform, but a computer guru, I am not. Any ideas?
What I've done so far:
I have checked for updated drivers and installed them.... no fix. I rolled back the drivers.... no fix. I have visually checked fans on power supply and graphics card to make sure they are working and they are fine. The fan on the motherboard spins, but doesn't appear to be moving overly fast. I checked BIOS and everything looks around what it should be for temp settings. In the "problems and solutions" application, it shows a video hardware error.
The only thing i did notice was there is only a 400W power supply installed and from the posts I've read, the 8800GT graphics card should have a 700-900W power supply. However... I've never had problems with it before. Could this cause the problem after 1 1/2 years?
help... i'm shaking from game withdrawals

Visited a company IT department today and an engineer looked at the AT&T Net Client settings. It now works - this may have been the "fix" for those in a similar predicament (all in the AT&T Net Client):
1. Click "Settings".
2. Click "Show the login properties window".
3. Click "Configure".
4. Click "Next".
5. Select the "Both the internet and my company's intranet" radio button.
6. Select "Managed VPN - SSL DualAccess" from the dropdown.
7. Click "Finish".
Cheers,
- Pete

KVM switch and Mavericks don't play well together

I upgraded to Mavericks yesterday, and started having this very annoying problem with my KVM switch, which used to work fine with Mountain Lion. I've been using this KVM switch for my mac mini and PC, in order to share my keyboard and mouse, very stably for several months.
Basically, when switching back and forth, there is a chance that ALL the peripheral devices would stop working in Mavericks. This includes my apple bluetooth keyboard and the magic touchpad, which are not related with USB (or maybe the bluetooth chip is still hooked up via USB inside).
For some reason, screen sharing stops working too, althought the IP I was trying to connect to was the ethernet port.
If I try to do a shutdown -r now via SSH, the system tries to shut itself down, but would get stuck with a spinning animation on the screen.
There is nothing in the system log, no error message.
My KVM switch is an IOGear GCS42UW6. Connected USB devices are: Apple USB keyboard and Logitech G500 mouse.

10.8 worked well with my Mac Mini (2009) connected to IOGEAR KVM model GCS1108. My mouse is from Redmond and the keyboard is a Goldtouch.
Mavericks has a problem with my KVM switch as well. It seems to be a USB problem.
Case 1: The Mini's video is connected to the KVM switch -- mini DVI port to DVI. If the KVM USB cable (known good) is connected, the Mini chimes at boot but no grey Apple logo appears. LCD remains blank white. Boot does not progress.
Case 2: The Mini's video is connected to the KVM switch, as before. If the KVM USB cable is NOT connected, the Mini chimes at boot, the grey logo appears, and boot proceeds normally. Video is fine. I then connect the KVM USB cable to the Mini and use keyboard and mouse. KVM switching works as expected.
If the KVM USB cable is NOT connected but a keyboard and mouse are connected directly to the Mini, the boot sequence is normal. Video works.
The problem is not the hardware, all of which worked well with 10.8 (Mountain Lion). I would downgrade if Apple made 10.8 available from the App Store.

Apple logo and Blue Screen freezes at boot up

I am frequently unable to boot up. The computer boots as far as the first blue screen with the Apple logo but the spinning pinwheel beneath the logo does not appear to signify any further booting activity. I have to switch off and switch on again. It freezes again at the same spot. So I do a PRAM reset and it works, but only for a couple of days or so before the problem returns. To provide some background, my MacBook Pro is 3 months old, I upgraded to Leopard 2 weeks ago using the upgrade option, and I use Bootcamp (which I updated with new drivers after the Leopard upgrade.) Since upgrading to Leopard, booting is MUCH slower than it was in Tiger. I have repaired permissions and received the following error messages after repair:
Warning: SUID file "usr/libexec/load_hdi" has been modified and will not be repaired.
Warning: SUID file "System/Library/PrivateFrameworks/DiskManagement.framework/Versions/A/Resources /DiskManagementTool" has been modified and will not be repaired.
Warning: SUID file "System/Library/PrivateFrameworks/DesktopServicesPriv.framework/Versions/A/Reso urces/Locum" has been modified and will not be repaired.
Warning: SUID file "System/Library/PrivateFrameworks/Install.framework/Versions/A/Resources/runner " has been modified and will not be repaired.
Permissions differ on "private/var/log/secure.log", should be -rw------- , they are -rw-r----- .
Warning: SUID file "System/Library/PrivateFrameworks/Admin.framework/Versions/A/Resources/readconf ig" has been modified and will not be repaired.
Warning: SUID file "System/Library/PrivateFrameworks/Admin.framework/Versions/A/Resources/writecon fig" has been modified and will not be repaired.
Warning: SUID file "usr/libexec/authopen" has been modified and will not be repaired.
Warning: SUID file "System/Library/CoreServices/Finder.app/Contents/Resources/OwnerGroupTool" has been modified and will not be repaired.
Warning: SUID file "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/MacOS/ARDAg ent" has been modified and will not be repaired.
ACL found but not expected on "Library".

Reinstalling MacOS does NOT fix the problem for me. I'm still searching a solution !
Bernard

Crash and Blue Screen on Flash

I'm getting a blue screen and computer crash everytime flash starts to play a file on IE or Firefox. All files are up to date and jsut switched from Trend Micro to Bitdefender. Please help.

uninstall your current flash player: http://helpx.adobe.com/flash-player/kb/uninstall-flash-player-mac-os.html
then update your browser.
then install your flash player: http://get.adobe.com/flashplayer/
p.s. untick mcafee unless you're 100% certain you want it.

Application Enhancer and Blue Screen

I have had Leopard running for a few weeks on my iBook G4 now with no problems.
Last night I wanted to listed to some music through my Airport Express but I don't like the way Airtunes drops the connection if I am switching songs and take a couple of second to do it.
So I started up Airfoil and it asked if I wanted to install Instant Hijack. I said yes.
BIG MISTAKE!
Application Enhancer is apparently used to run Instant Hijack and one or the other trashed my system. It would never get past the blue screen at the startup even after being left to startup for an hour.
DO NOT try to run these programs on Leopard until they are updated they will trash the system.
I spent this morning trying everything to recover the system and finally gave up and reinstalled the system.

Hi,
this is a known problem. Logitech keyboard/mouse drivers also use APE. You might want to know that there's even a support document about this. So the next time you run into a problem like this you won't need to reinstall everything. Take a look:
http://docs.info.apple.com/article.html?artnum=306857
Björn

Belkin Flip KVM Switch and Blue Screen

Similar Messages

Maybe you are looking for