Callmanager Conferencing with remote locations Issue
I am new to using callmanager, and I need a little help.
I have created a meet me number on my callmanager. Once a session is begun, all local network users are able to join the conference call with no problems..
If a remote location hosts a meet me call, all my local network users are able to join THAT session with no problems as well.
But if I host a meet me session on MY local network, remote locations CANNOT reach my session. The line remains silent when they dial in.
I've been told to check the codecs which seem fine and we are checking for a firewall issue, but all normal calls local and remote work just fine. It's only the conference bridging that causes issues.
Please help.
Thanks
Hello,
Thank you very much for replying.
The configurations, I've been told, are correct. G711 for intrasite and G729 for intersite. And region and device pools correct as well.
I presented the HW conf bridge solution to a coworker who said it makes sense, but at this time, I don't have access to a hardware conference bridge. Is this the only solution?
From: prbt
To: Nichole Ketchum
Sent: Wednesday, August 3, 2011 1:54 PM
Subject: - Re: Callmanager Conferencing with remote locations Issue
Cisco Support Community
Re: Callmanager Conferencing with remote locations Issue created by Priya B.T in Unified Communications Applications - View the full discussion
hi,
please check the following on the call manager,
- Check the region configuration on each device pool.
- Then check the region configuration between the two regions.
- One of the best practices followed by Cisco is, the intrasite region settings should be g711.
- And the region settings between inter site should be g729.
- G729 is not supported by software conference bridge, it is only supported by hardware conference bridge.
- So add the hardware conference bridge to the MRGL of the phone.
- And the hardware conference bridge has to be first in the list, that is before the software conference bridge.
please let me know if this helps or we can do further trouble shooting on this issue.
Reply to this message by going to Cisco Support Community
Start a new discussion in Unified Communications Applications at Cisco Support Community
Similar Messages
-
My company recently had an outside company create a homepage
for us and it was turned over to me to create the rest of the
pages. I am new at Dreamweaver and just can't figure out how to fix
this problem. The woman who created the site for us has not been
able to help me, either.
Here is the problem:
When I access the file "index.html" that she created in the
"Files" panel and open it in Dreamweaver, it looks perfect, but
when I hit F12 to view in IE, I lose all of the text in my column
on the left. It seems to be an issue of images or something... we
are not currently live with her hosting yet. Can I just continue to
create pages and hope it will be okay once we go live?
Any help would be appreciated.
LauraCan't help much without seeing the code.
Can you upload somewhere and post a link?
Or at least post the entire page code.
I am guessing it is an IE only problem having to do with the
widths of your
DIV's not fitting in the container
IE counts differently than let's say Firefox.
"LauraK77" <[email protected]> wrote in
message
news:g7htac$1jp$[email protected]..
> My company recently had an outside company create a
homepage for us and it
> was
> turned over to me to create the rest of the pages. I am
new at
> Dreamweaver and
> just can't figure out how to fix this problem. The woman
who created the
> site
> for us has not been able to help me, either.
>
> Here is the problem:
> When I access the file "index.html" that she created in
the "Files" panel
> and
> open it in Dreamweaver, it looks perfect, but when I hit
F12 to view in
> IE, I
> lose all of the text in my column on the left. It seems
to be an issue of
> images or something... we are not currently live with
her hosting yet.
> Can I
> just continue to create pages and hope it will be okay
once we go live?
>
> Any help would be appreciated.
> Laura
> -
How do I use iCloud to collaborate on a GarageBand project with a remotely located musician?
How do I use iCloud to collaborate on a GarageBand project with a remotely located musician? He is in Valencia, Spain, I am in Green Bay, Wisconsin. We'd like to be able to work on the same GarageBand document together, laying down tracks, etc.
Is there a tutorial I should look at?Are you using GarageBand on a Mac or on an iPad?
With iCloud you can store your GarageBand projects in iCloud, so you can work on the same project on all your iPads, iPods, iPhones, and transfer it from your iDevices to your Mac. But you cannot use iCloud to share a project between people with different AppleIDs.
To send GarageBand projects back and forth, compress the the ":band" files and mail them, if they are small enough or put them in a Dropbox or other cloud storage and mail the link. -
I'm having a huge issue with itunes locating my missing files..and it's too many for me to locate 1 by 1..It says I'm missing over 3,000 songs and They are all in my music folder..What can I do to fix this issue? I've looked at all the tutorials on youtube and none of it works. I recently got a new computer and I Back-Up all my music and itunes playlist and I import it on my new computer with the new itunes and I go to play a few songs, it says I'm missing them I locate a few but it's still like 3,000 missing and again they are all on the computer and in one folder..Please Help !
I did that and nothing changed half my songs still have examination marks beside them
I also just tried dragging my folder of music int he playlist and it duplicated all of my songs? My playlist was at 5k now it's at 10k becuz of 3 duplicates of songs. Is there a way to delete multiple duplicate files? -
Accessing multiple macs with ARD from remote location with Airport Extreme
We have an office with a newer Airport Extreme and three macs on the network. We have turned on the Apple Remote Desktop in the port forwarding, but we can only access one computer at a time, and only if we port map it to the local IP of that computer (Ex 10.0.1.2).
We would like to be able to access all three computers from a remote location. My question is this -
Can I have a wildcard IP, or is there an IP I should use for ARD?
Do I set up multiple port mapping with different ports and IPs?
All computers are running 10.6.1 with the latest ARD updates.
Any assistance would be appreciated.Great answer by Dave Sawyer:
"To be able to connect to a workstation from outside it's network, the ports that ARD uses must be open on both ends of the connection. ARD uses ports 3283 and 5900 so those must be open.
If your workstations get their addresses from an NAT device rather than being "real", the ports also need to be forwarded in the router to the workstation's internal IP address. ARD uses port 3283 for the reporting and updating function, so if your Macs are getting their IP addresses through NAT, since you can only forward a port to a single workstation, you can only get reports, push package/files to etc. for a single workstation.
ARD uses the VNC protocol for observation and control, though, and there are a range of IP addresses for that protocol, starting with 5900. ARD uses 5900 by default, so that port would be forwarded to the first workstation. To be able to control more than one system, though, you would need to install VNC servers on the systems (since the ARD client cannot listen on any port other than 5900 while VNC servers can be set for other ports such as 5901, 5902, etc. You would then forward 5901 to the second workstation (and on to 5902, 5903, etc.). You can then use the following information:
Remote Desktop 2: How to specify a port number for a VNC client to connect. -http://support.apple.com/kb/TA22880
The only other options are: 1) to run the ARD administrator on a workstation on the network, and then take control of that system from outside, either via VNC or another copy of ARD, or 2) set up a virtual private network (VPN) so that when you connect from outside, your admin system is officially part of the local network.
Hope this helps." -
Is it possible to have a phone line connected to a Mac Mini (OS X10.8.2) so you can use your computer with Parallels (Windows xp) to dial into a modem to download data being collected and stored at the remote location?
Hi, do you mean a real Dial-up Modem as in the old days?
As I recall, the Apple USB Modem won't work in 64 bit OSes, but there are others that will, I think this is one of them...
http://www.zoomtel.com/products/dial_up_external_usb.html
Or is the Modem on the other end Cable/DSL/FiberOptic? -
ACE implementation with servers at remote locations
Hi,
We are having two ACE appliances in the datacenter in failover mode. Currently, we using route mode with two servers placed in the DC which are getting load balanced. Now, we are planning to move the servers to a new location and this location is reachable via WAN from the DC. Is there any challenge in moving the servers to a new location.
1. Do we need to do any natting ?
2. Is there any configuration document for ACE appliance using route mode with NAT ?
Any help would be appreciated.
Rgds./
SckThere are 2 things to look at.
1/ Make sure the ACE can reach the server (ping)
2/ Make sure the return traffic from the server goes back to the ACE
This 2nd point can be tricky when the servers are not directly connected to ACE.
The servers will see the connections coming from clients (not ACE ip address), therefore they will use a default gateway to send the response which does not necessarily send traffic back to ACE.
You may need policy routing on the gateway.
Or you may have to configure client nat (in this case, the servers see the connections coming from ACE itself), but then you lose information about client source ip. This can be solved by doing header insert but this is only possible for HTTP and it has a cost in terms of performance.
The best option is to keep the servers close to the loadbalancer.
If you want to move both servers, see if you can also move the loadbalancer to the same remote location.
Gilles. -
PSP, router, and modem issues with Remote Play
Background:
Verizon DSL
Westell 6100 modem
WRK54G router
PS3
PSP
I haven't seen a post on this topic yet, so I'll explain the issue. The Playstation 3 is networkable either through a wired ethernet or wireless connection. The Playstation Portable is also networkable over wifi. The PSP has always worked at hot spots for web surfing and gaming. With the release of the PS3, there was a new feature called Remote Play, which let you connect your PSP to your PS3 and stream the PS3 interface. You can manipulate the options, watch videos and listen to music, just like you are at the controls of the PS3. The PS3 has to be put in "remote play" mode for this to work.
Last week, Sony released an update that made this functionality work over the internet. For most people this worked just fine. Others had to open ports here or there, but there is a group of users that cannot connect from a hot spot, but can connect over the internet at home. The original remote play connection (before the update) was a direct connection between the PS3 and PSP. Now you can connect through your router at home (scan for your router and connect that way). This connection works since the PS3 and PSP are both connected to the same router in your home. When you go to a hotspot, you can get all the way up to the point that the PS3 streamed screen should start, but it times out.
This is taken directly from the PS3 owner's manual:
"If the PS3 system is connected to the Internet via two or more routers, communication may not work correctly."
It seems like internet connection from a hot spot doesn't work because the request for the PS3 gets lost between two routers when it gets to my home network.
Finally to my question. It seems like my Westell 6100 is functioning as a router, as is my WRK54G. When i look at my modem's settings, it is set up as a bridge protocol in routed bridge mode. Everything else I try makes me lose my internet connection.
Anybody know what I'm talking about or have any suggestions?
ThanksA lot of PS3/PSP owners are having this issue with Remote Play. I have a WRT350N and have been through Sony forum as well as this one to know about all setups from port forwarding to giving your PS3 a static IP and placing in DMZ. I can say I had success connected via or public wi-fi but I also noticed how unstable Remote Play is. There will be times you can connect to it but if you turn your PS3 completely off (not standby) and back on you will pretty much need to setup your PSP again with the PS3 for Remote Play. The problem itself lies more with Sony and not our modem and routers except that fact that you do have to make some minor changes like disable UPnP, forward ports and etc. I own the Sony LocationFree Player which uses a similiar function like Remote Play but instead gives you control over your cable tv remotely anywhere on laptop or psp. LocationFree never failed me since day one because Sony created a DDNS for it which worked for me no matter who my carrier was or what router I have used over the years. Remote Play was introduced later for PS3 which pretty much like LocationFree but Sony doesn't provide a DDNS for it, instead we have to go through all the crazy configurations which is never stable. However you can register for a DDNS at DynDNS.org and configure your router with it which I have done before and found it to be very stable. No matter what Sony still needs to address the issue with the PS3 communication for Remote Play. You can find a lot of info here for setting up DDNS and as for Remote Play your better off going to the Playstation Forums. Good Luck!
-
Delete from remote location with where clause between the two databases
I want to delete records from a source database using dblink. The criteria for the delete is a where clause, that
looks for the values between a table at source and the remote location. I get an invalid sql statement error.
When i do a count(*) instead of a delete, I get rows returned.
Can anyone see an the problem here ? I've tried qualifying the delete
delete from tabl1@remote a, tabl1_temp b where (a."id" =b."id") and (a."title" = b."title) and (a."key" = b."key");
the error I get is ORA 00933 SQL command not properly ended....
The * is between the 2 ands ...
Edited by: sgonos on Nov 6, 2009 6:46 AM
Sorry the * moved when I save it ...
delete from tabl1@remote a, tabl1_temp b where (a."id" =b."id") and (a."title" = b."title) and (a."key" = b."key");
it's flagging the middle and ... a.title = b.title ... seems to like key ....
Edited by: sgonos on Nov 6, 2009 6:51 AMYou have 2 tables specified in the delete clause of your statement.
It should maybe be something like:
delete from tabl1@remote a
where exists (select 'x' from tabl1_temp b where (a."id" =b."id") and (a."title" = b."title) and (a."key" = b."key"));
{code} -
Noticed keynote remote will not pair after updating. Bluetooth light flashes a couple of times then goes off. I'm wondering if it's a bluetooth issue or a keynote remote app issue.
Any suggestions or remedies?
thanksThen again, it may not.
I've tried all the things recommended in the Apple KB article, and it doesn't work. Mulderscully is right, in the recent iOS 5 upgrade, Bluetooth is not turned on (at least, its symbol is not visible) from within Keynote even if you turned it on in the Settings menu. Posts in another thread recommended using another app to establish a Bluetooth connection between the iPad and iPod (I used Touch Rummy), then switching back to Keynote and Keynote Remote. This does work for me, but it is an awkward workaround. Shouldn't 'It just work'? -
Ipod Universal Doc with Remote Issue
Hi Guys
Wonder if you can help, I have a 80GB black classic iPod and have bought the Uni Doc with Remote - The Remote will only control the sound and nothing else. I have tried re-syncing the remote but with no luck
Any ideas??Hmmm, good question. Its at home right now and I'm at work... I want to say that it is a flat receiver. I bought it with the iPod Touch, it came with about 8 different plastic pieces to fit a few different iPods, and it doesn't have the S-video connector in the back... just an audio out, and the same dock connector slot in the back which is hooked up to my component cable. It works with both my iPod Touch and iPhone 3G, it displays tv shows and movies perfectly on my tv, but it won't jump back and forth in my play list. I think I've got 3 or 4 different remotes lying around; I assumed that they were all the same, but is it possible that the remote that came with the dock is different than the remotes that came with the Mac Mini, MacBook, and MacBook Pro?
-
I have 3rd party software wirelessly injected and used on my iphone with a cryptographic authentication system without my consent (seems to be new technology developed by stanford and apple security is not updated for this technology) obtaining ownership of my iPhone 4s software and controlling it with remote device to jail breaking my phone, adding and removing software, changing settings all from a remotely controled device from different location (I have a Mac address I'd of this device to know for sure). Almost undetectable. When I look at the legal section of my phone it shows a list of all the unauthorized 3rd party software "as is" copyright encrypted on the phone. This is the most basic way to legally steal software of any kind. Because of this legalality 3rd party ownership have total control of certain software correlated with hardware use including visualization technology, etc. most people luckily will never have this happen to them so it's unlikely many readers have not a clue of what I'm saying currently. Either way, without needing to obtain specific warranty of any kind "as is" copyright control makes system restores not a solution because the source code is not directly encrypted on the actual hardware device only a copy right notice must appear on the specific device 3rd party software validation making it extremely difficult for me to take control of the situation. Apple claims their iOS technology prevents this type copyright obstruction from being possible, however, according to my phone a new form of technology was used developed by Tom wu of Stanford university called the STANFORD SRP AUTHENTICATION TECHNOLOGY which uses Some form of cryptographic authentication system and uses quote "secure remote password" which seems to suceed in hacking iOS apple technology apple claims is not possible to jailbreak an unstolen phone or without the owners consent As well as loading the device with 3rd party copyright Notices to make all of this legalized. My phone shows atleast 30 pages worth of legalized 3rd party copyright permissions! Yesterday my apple care provider labeled me a jailbreaker and refused to look at my legal documented proof which completely blew my mind because it voides my apple care contract I spent 100 on. This employee did not take all factors into consideration and made quick assumptions as well as verbally speaking to me as I'm an automatic criminal. I left the store yesterday with no payed insurance help on a problem I had no control over and couldn't prevent, leaving with voided contracts. This is an apple users worst nightmare and I have spent days researching all of this like i am some kind of lawyer only to be able to use my phone the way it should and spent alot of money on. I can legally backup any claim I have just wrote above currently and have a large source of data collected to prove apple is wrong in voiding insurance support on this issue. The problem lies in apple avoiding and not wanting to believe their software can legally be obtained ot "hacked". Yet still labeled a jailbreaker basically.. What should I do????? Been to local apple store 3 times and rebooted my phone as well sprint service restore 4 times and spoke with reps twiice on the phone. Spoke with my phone provider who said apple has full control over these matters so they can't help me. My case is according to apple "still open"...Anyone else heard of this or of Stanford's office of technology licensing? Maybe I need to buy a blackberry again or just use a landline so I can stop being my own lawyer and focus on other productive areas in life instead of this horrible mess. I shouldn't have to prove to apple I not a jailbreaker they should have to prove I'm one before voiding support I desperately need!!
Mullaly75 wrote:
I assume u guys don't understand what open source software is
Yes, I think most of us do understand what open source software is. It sounds as if you don't. Here's some information:
Open-source software (OSS) is computer software that is available in source code form: the source code and certain other rights normally reserved forcopyright holders are provided under an open-source license that permits users to study, change, improve and at times also to distribute the software.
Open source software is very often developed in a public, collaborative manner. Open-source software is the most prominent example of open-sourcedevelopment and often compared to (technically defined) user-generated content or (legally defined) open content movements.
from http://en.wikipedia.org/wiki/Open_source_software
Yes, Tom Wu of Stanford wrote a paper on something called Secure Remote Access Protocol. It's a form of Asymetric Key Exchange and has nothing to do with hacking anything. It's actually intended to protect data. -
9971 SIP Phones at remote location status REJECTED
Hi,
I have 10 locations, Site 1, 2, ....10. All these locations have 10 phones each. These phone are configured with default SIP Profile. Were registered and working fine. While adding a subscriber I downgraded the cluster. After bringing back to regular version. I find all my phones status shows unknown.
I tried to change dhcp option 150 on dhcp router to point different server and reconfigured with the correct tftp ip address. Also I tried to shutdown the interface where phones are connected and bring it back up. Restarted tftp server many times. Even after all these I find my phones in REJECTED state.
I know personal reset on each phone will fix this issue. But is there any other way to fix this, since these phones are at remote locations.
Any help is appreciated.
Thanks,
MRHello!
I think, that the most possible issue is problem with CTL/ITL.
Certificates were regenerated while downgrading/upgrading and were not propagated to the phones.
So u should try to delete ITL on the phones.
Regards,
Kirill -
Cloning a Mac OS X Server to a remote location
Scenario: A Mac Mini running Mac OS X Server is in location A and a second Mac Mini running Mac OS X Server is to be acquired and setup at a remote location.
Desire: Do a nightly backup of Server A to the second Mac Mini so that Server B is a bootable clone of the primary server.
Question: What is the best software/approach to do this?
Discussion: I'm familiar with and use SuperDuper, Synchronize Pro and Carbon Copy Cloner for performing file by file backups and synchronization where the hard drives are on the same server ... but I'm not sure if any of these are the best alternative to backup a MAMP Pro installation on the Server (along with other applications and data) to a remote server box.
I realize that particularly within the Moodle VLE (that will be running on the servers) that absolute links will still point to the primary server but that is not an issue for me. In the event of a catastrophic failure of Server A at least there would be an offsite clone that could be accessed if a few settings were changed.
BTW: Server A is hosted by a commercial hosting service and no backup drive is available on-site for a file x file backup/synchronization. We do have full access to the server via ARD, Timbuktu Pro, AFP, etc.Can you expand your info on the use of these two approaches, particularly the mysql replication
Well, my approach requires that there's some kind of connectivity between the two machines - preferably a VPN network to secure the traffic, but it doesn't have to be done that way.
rsync essentially takes two directories - one local and one remote - and compares the differences. Depending on the switches you use it will copy the changes from one system to the other (or both if that's what you prefer). In this case I'd set it to copy the local web directory to the remote machine, so the remote machine has a copy of all the files.
rsync works best for static files (e.g. .html, .php, etc. in the case of a web application), but shouldn't be used for dynamic files such as your database files.
As for the data, MySQL has substantial built-in replication routines that are designed to keep multiple database servers in sync. There's far more to it than I can go into here, suffice to say it can maintain a real-time copy of your data on a second, remote machine, and you should read the documentation for the specifics. -
Remote debugging issue: Address already in use
First, I want to explain that to use remote debugging in oracle UCM server (IdcServerNT.exe), I add these lines at */server/bin/intradoc.cfg*:
JAVA_OPTIONS_debug_enable=-Xdebug
JAVA_OPTIONS_debug_options=-Xrunjdwp:transport=dt_socket,server=y,address=8000,suspend=n
and since the JAVA_OPTIONS is shared between admin server (IdcAdminNT.exe) and non-admin server (IdcServerNT.exe), to prevent "Address already in use" error, I added same lines but with empty value into */server/admin/bin/intradoc.cfg*:
JAVA_OPTIONS_debug_enable=
JAVA_OPTIONS_debug_options=
or alternatively enable it but use different port for the "address=xxx".
Now the issue is when I had run the non-admin UCM server with remote debugging enabled, then I tried to run the Component Wizard, I got "Address already in use" error:
ERROR: transport error 202: bind failed: Address already in use ["transport.c",L41]
I found out that's possible because Component Wizard (ComponentWizard.exe) is using same setting file with non-admin server (IdcServerNT.exe): */server/bin/intradoc.cfg*. It's obvious that happened because of ComponentWizard.exe is in same location with IdcServerNT.exe, so I think other tools like Batch Loader and System Properties will be affected with same issue too.
Because of this issue, everytime I want to open Component Wizard, I had to stop the non-admin server which is inconvenient.
So, the question is there a way to define separately or disable the JAVA_OPTIONS_debug_enable & JAVA_OPTIONS_debug_options for Component Wizard?WillT wrote:
My run method was being called somewhere else and I can't find out whereOkay, but changing from implementing Runnable to extending Thread won't change that one whit. You must've also changed something else.
Extending Thread is the wrong approach, since you're not creating a special kind of Thread.
Maybe you are looking for
-
could I use a 20$ giftcards from iTunes for a failed purchase Instead of a new credit card? I'm not going to add a new credit card to my account. When I try to update or download a new app it tells me I have to update my billing. So I can't do anythi
-
Can't view WMP files in Safari on Intel machine unless in Rosetta??
I am trying to set up my parent's new Mac Mini w/ a core Solo Intel chip. They want to be able to view videos on CNN, but the only way i've been able to get them to work is by downloading the WM9 player, then launching Safari under Rosetta, which is
-
R9 270 dvi-dvi-hdmi eyefinity doesn't work. AMD fake specs?
I am trying to set up 3 24" monitors for eyefinity but I can't seem to get the third monitor to show any picture. From what I understand the R9 270 no longer require the usage of a display port. AMD Eyefinity Technology (Maximum displays) 3 with DVI/
-
I have a new Macbook pro with FCE and am wondering how I would be able to capture some footage into my computer from an authored DVD. Could I do it through FCE? iMovie?
-
Best screen capture resolution for FCP
I'm making some tutorials of various computer software. I'm going to edit them with FCP. I'm using the MAC built in SHIFT-COMMAND - 3 or 4 in order to snap stills off my screen, and then import into Final Cut Pro to edit the tutorials with. The still