Can bus HELP
I am working on the zebra battery and i need some help that how i use the can bus. I need to interface the zebra battery with pc and to automize it using LABVIEW. The zebra battery is using a can protocol. I have NI-USB-8473. I go thorught labview stuff. But i donot know from where i start. What should i do. Any advice?
What are you trying to do ? Send CAN messages and monitor the response or do some diagnostic activities ? USE NI CAN VI's to do all kinds of activities., as far as I can see you are trying to work on battery management systems where you might have to monitor cell voltage values, charging, discharging and others. Send CAN message in proper 11 bit or 29 bit format. Pls let us know what you need to do in specific and what kinds of problem are facing in your try, forum people are there to guide you.
Similar Messages
-
I bought my IPad 2 from a friend. I have reset to clear all of his information out. I am trying to connect it to my computer to sync my itunes and I keep getting the message that my IPad can't be used because Apple Mobile Device Service is not started can anyone help with this?
I cannot find "Other" devices. I found Apple Mobile Device under Universal Bus Controllers but cannot see "recovery mode" or any other status. I use Windows Vista.
When I try to restart Apple Mobile Device Service I get the following message: "The Apple Mobile Device Service on Local Computer started then stopped. Some services stop automatically if they are not in use by other services or programs". What does this mean?
During the last 48 hours I was able to see my iPad in iTunes only one time during many attemnpts to connect . I haven't been able to see it during the llast several attempts.
Any suggestions? The standard suggestions have not worked: i.e. stop then start AMDS; tuurn off iPad and PC, then restart both and reconfrom iPad to PC; reload iTunes. -
Can LabView simulate multiple nodes on a single CAN bus?
We currently are developing a system where a single control panel controls a number of drive motors over a CAN bus. Each of those drive motors has electronics and software in them which tracks the status of the motor, and this information is sent over the CAN bus to the control panel.
We have previously used Vector CANoe to simulate the activity of the drive motor nodes on the CAN bus during development of the control panel. We want to move to LabView in order to run this kind of simulation.
Is it possible for LabView to be used to run this kind of simulation? Each node would have its own CAN ID on the bus. It would need to send out appropriate periodic status messages on that CAN bus that would be based on user inputs. It would also need to display certain information based on commands sent to it via the control panel over CAN.
Thanks for the assistance.Hi,
I believe that what you need is to simulate several CAN ports. There is a similar discussion form that I believe will answer you question. I hope this helps.
Regards
Krista S.
Applications Engineering
National Instruments -
Can someone help me figure out why my MacBook Pro froze...
I just closed a usb drive window, and ejected the drive when my computer suddenly froze. I was running: Excel, Firefox, Speed Download, and Mail.
After about ten minutes or so of waiting I restarted my computer and found this log. Can you help me figure out what went wrong?
Oct 24 07:42:27 Alpha diskarbitrationd[39]: LaunchCFMApp [263]:30995 not responding.
Oct 24 07:42:27 Alpha diskarbitrationd[39]: LaunchCFMApp [262]:29991 not responding.
Oct 24 07:42:27 Alpha diskarbitrationd[39]: iTunes [260]:28715 not responding.
Oct 24 07:42:27 Alpha diskarbitrationd[39]: coreaudiod [38]:28179 not responding.
Oct 24 07:42:27 Alpha diskarbitrationd[39]: firefox-bin [219]:25667 not responding.
Oct 24 07:42:27 Alpha diskarbitrationd[39]: Mail [202]:27651 not responding.
Oct 24 07:42:27 Alpha diskarbitrationd[39]: Starry Night [199]:26627 not responding.
Oct 24 07:42:27 Alpha diskarbitrationd[39]: Speed Download [197]:26123 not responding.
Oct 24 07:42:27 Alpha diskarbitrationd[39]: LittleSnitchDaemon [182]:23555 not responding.
Oct 24 07:42:27 Alpha diskarbitrationd[39]: Finder [179]:19459 not responding.
Oct 24 07:42:27 Alpha diskarbitrationd[39]: SystemUIServer [178]:17923 not responding.
Oct 24 07:42:27 Alpha diskarbitrationd[39]: SystemUIServer [178]:16403 not responding.
Oct 24 07:42:27 Alpha diskarbitrationd[39]: Dock [176]:16899 not responding.
Oct 24 07:42:27 Alpha diskarbitrationd[39]: ATSServer [63]:12803 not responding.
Oct 24 07:51:57 localhost kernel[0]: hi mem tramps at 0xffe00000
Oct 24 07:51:57 localhost kernel[0]: PAE enabled
Oct 24 07:51:57 localhost kernel[0]: standard timeslicing quantum is 10000 us
Oct 24 07:51:57 localhost kernel[0]: vmpagebootstrap: 383643 free pages
Oct 24 07:51:57 localhost kernel[0]: migtable_maxdispl = 71
Oct 24 07:51:57 localhost kernel[0]: Enabling XMM register save/restore and SSE/SSE2 opcodes
Oct 24 07:51:57 localhost kernel[0]: 89 prelinked modules
Oct 24 07:51:57 localhost kernel[0]: ACPI CA 20060421
Oct 24 07:51:57 localhost kernel[0]: AppleIntelCPUPowerManagement: ready
Oct 24 07:51:57 localhost kernel[0]: AppleACPICPU: ProcessorApicId=0 LocalApicId=0 Enabled
Oct 24 07:51:57 localhost kernel[0]: AppleACPICPU: ProcessorApicId=1 LocalApicId=1 Enabled
Oct 24 07:51:57 localhost kernel[0]: Copyright (c) 1982, 1986, 1989, 1991, 1993
Oct 24 07:51:57 localhost kernel[0]: The Regents of the University of California. All rights reserved.
Oct 24 07:51:57 localhost kernel[0]: using 7864 buffer headers and 4096 cluster IO buffer headers
Oct 24 07:51:57 localhost kernel[0]: Enabling XMM register save/restore and SSE/SSE2 opcodes
Oct 24 07:51:57 localhost kernel[0]: Started CPU 01
Oct 24 07:51:57 localhost kernel[0]: IOAPIC: Version 0x20 Vectors 64:87
Oct 24 07:51:57 localhost kernel[0]: ACPI: System State [S0 S3 S4 S5] (S3)
Oct 24 07:51:57 localhost kernel[0]: Security auditing service present
Oct 24 07:51:57 localhost kernel[0]: BSM auditing present
Oct 24 07:51:57 localhost kernel[0]: disabled
Oct 24 07:51:57 localhost kernel[0]: rooting via boot-uuid from /chosen: 831ACFE5-5EEF-4B22-8C04-C0A6524AADB7
Oct 24 07:51:57 localhost kernel[0]: Waiting on <dict ID="0"><key>IOProviderClass</key><string ID="1">IOResources</string><key>IOResourceMatch</key><string ID="2">boot-uuid-media</string></dict>
Oct 24 07:51:57 localhost kernel[0]: USB caused wake event (EHCI)
Oct 24 07:51:57 localhost kernel[0]: Debug driver registered: AppleUSBUHCI
Oct 24 07:51:57 localhost kernel[0]: FireWire (OHCI) Lucent ID 5811 PCI now active, GUID 0016cbfffe4ccb7a; max speed s400.
Oct 24 07:51:57 localhost kernel[0]: CSRHIDTransitionDriver::probe: 0x0
Oct 24 07:51:57 localhost kernel[0]: CSRHIDTransitionDriver::start before command
Oct 24 07:51:57 localhost kernel[0]: Got boot device = IOService:/AppleACPIPlatformExpert/PCI0@0/AppleACPIPCI/SATA@1F,2/AppleAHCI/PRT2 @2/IOAHCIDevice@0/AppleAHCIDiskDriver/IOAHCIBlockStorageDevice/IOBlockStorageDri ver/TOSHIBA MK8032GSX Media/IOGUIDPartitionScheme/Customer@2
Oct 24 07:51:57 localhost kernel[0]: BSD root: disk0s2, major 14, minor 2
Oct 24 07:51:57 localhost kernel[0]: jnl: replay_journal: from: 4944384 to: 6034432 (joffset 0xa701000)
Oct 24 07:51:57 localhost kernel[0]: CSRHIDTransitionDriver::stop
Oct 24 07:51:57 localhost kernel[0]: HFS: Removed 1 orphaned unlinked files
Oct 24 07:51:57 localhost kernel[0]: USBF: 27.725 AppleUSBEHCI[0x2d6f000]::Found a transaction which hasn't moved in 5 seconds on bus 253, timing out!
Oct 24 07:51:57 localhost kernel[0]: Jettisoning kernel linker.
Oct 24 07:51:57 localhost kernel[0]: Resetting IOCatalogue.
Oct 24 07:51:57 localhost kernel[0]: Matching service count = 0
Oct 24 07:51:57 localhost kernel[0]: Matching service count = 0
Oct 24 07:51:57 localhost kernel[0]: Matching service count = 0
Oct 24 07:51:57 localhost kernel[0]: Matching service count = 0
Oct 24 07:51:57 localhost kernel[0]: Matching service count = 0
Oct 24 07:51:57 localhost kernel[0]: Matching service count = 0
Oct 24 07:51:57 localhost kernel[0]: Previous Shutdown Cause: 3
Oct 24 07:51:57 localhost kernel[0]: mac 10.3 phy 6.1 radio 10.2
Oct 24 07:51:57 localhost kernel[0]: IPv6 packet filtering initialized, default to accept, logging disabled
Oct 24 07:51:57 localhost mDNSResponder-108.2 (Aug 25 2006 14: 50:48)[33]: starting
Oct 24 07:51:57 localhost memberd[40]: memberd starting up
Oct 24 07:51:57 localhost lookupd[44]: lookupd (version 369.6) starting - Tue Oct 24 07:51:57 2006
Oct 24 07:51:57 localhost DirectoryService[45]: Launched version 2.1 (v353.2)
Oct 24 07:51:59 localhost configd[37]: com.apple.SystemConfiguration.DynamicPowerStep load failed
Oct 24 07:51:59 localhost kernel[0]: yukonosx: Ethernet address 00:16:cb:8a:7a:43
Oct 24 07:51:59 localhost diskarbitrationd[39]: disk0s2 hfs BABDE111-6071-3972-9C86-77812E4EB69A Macintosh HD /
Oct 24 07:51:59 localhost kernel[0]: AirPort_Athr5424: Ethernet address 00:14:51:ed:9a:ae
Oct 24 07:52:01 Alpha configd[37]: setting hostname to "Alpha.local"
Oct 24 07:52:02 Alpha lookupd[62]: lookupd (version 369.6) starting - Tue Oct 24 07:52:02 2006
Oct 24 07:52:02 Alpha /System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow: Login Window Application Started
Oct 24 07:52:03 Alpha kernel[0]: AppleYukon - en0 link active, 100-Mbit, full duplex, symmetric flow control enabled
Oct 24 07:52:03 Alpha loginwindow[64]: Login Window Started Security Agent
Oct 24 07:52:05 Alpha configd[37]: executing /System/Library/SystemConfiguration/Kicker.bundle/Contents/Resources/enable-net work
Oct 24 07:52:05 Alpha configd[37]: posting notification com.apple.system.config.network_change
Oct 24 07:52:05 Alpha lookupd[74]: lookupd (version 369.6) starting - Tue Oct 24 07:52:05 2006
Oct 24 07:52:07 Alpha mDNSResponder: Adding browse domain local.
aped[56]: mcxd[67] is running as the super-user. It is not possible for APE to affect this process in any manner whatsoever.
Oct 24 07:52:16 Alpha configd[37]: target=enable-network: disabled
Oct 24 07:52:47 Alpha kernel[0]: IOBluetoothHCIController::start Idle Timer Stopped
Oct 24 07:52:48 Alpha kernel[0]: Registering For 802.11 Events
Oct 24 07:52:48 Alpha kernel[0]: [HCIController][setupHardware] AFH Is Supported
Oct 24 07:53:04 Alpha /Library/Application Support/LaCie/LaCie Backup/laciebackupd.app/Contents/MacOS/laciebackupd: laciebackupd could not load preferences for hotkeycode. Default : "s"
Oct 24 07:53:04 Alpha /Library/Application Support/LaCie/LaCie Backup/laciebackupd.app/Contents/MacOS/laciebackupd: laciebackupd could not load preferences for hotkeymodifier. Default : "controlKey"Checked to see how much space is available ??
Click your Apple menu top left in your screen. From the drop down menu click About This Mac > More Info > Storage
Make sure there's at least 15% free disk space. Less can slow your Mac down.
Check the startup disk lately?
Launch Disk Utility located in HD > Applications > Utillities
Select the startup disk on the left then select the First Aid tab.
Click: Verify Disk (not Verify Disk Permissions)
If DU reports errors, restart your Mac while holding down the Command + R keys. From there you should be able to access the built in utilities in OS X Recovery to repair the startup disk. -
Hello, my imac crashes every day, sometimes it's simply stop working in a black screen. I think that's something about video card, because every crash, I see a black screen or messed screen.
Can anyone help me find the main cause? Below is my last error report.
Anonymous UUID: DDB9DB5F-EA5B-B45F-F5A7-6307FCE2572B
Sat Sep 13 09:12:35 2014
Machine-check capabilities: 0x0000000000000806
family: 6 model: 23 stepping: 6 microcode: 1551
signature: 0x10676
Intel(R) Core(TM)2 Duo CPU E8335 @ 2.66GHz
6 error-reporting banks
Processor 1: IA32_MCG_STATUS: 0x0000000000000005
IA32_MC0_STATUS(0x401): 0xb200004000000800
IA32_MC5_STATUS(0x415): 0xb200121020080400
panic(cpu 1 caller 0xffffff80158dcad9): "Machine Check at 0xffffff7f973e73f7, registers:\n" "CR0: 0x000000008001003b, CR2: 0x0000000103e46000, CR3: 0x00000000181f2000, CR4: 0x0000000000000660\n" "RAX: 0x0000000000000031, RBX: 0xffffff8020905000, RCX: 0x0000000000000001, RDX: 0x0000000000000400\n" "RSP: 0xffffff80ae9e3d50, RBP: 0xffffff80ae9e3d80, RSI: 0x0000000000000004, RDI: 0xffffff80a8c45148\n" "R8: 0x00000000e0000000, R9: 0x0000000000000004, R10: 0x0000000104236380, R11: 0x0000000000000202\n" "R12: 0x0000000000000004, R13: 0xffffff80209e1240, R14: 0xffffff7f97404e20, R15: 0x0000000000000520\n" "RFL: 0x0000000000000046, RIP: 0xffffff7f973e73f7, CS: 0x0000000000000008, SS: 0x0000000000000010\n" "Error code: 0x0000000000000000\n"@/SourceCache/xnu/xnu-2422.110.17/osfmk/i386/trap_native.c :168
Backtrace (CPU 1), Frame : Return Address
0xffffff80a8bd5e80 : 0xffffff8015822f79
0xffffff80a8bd5f00 : 0xffffff80158dcad9
0xffffff80a8bd6060 : 0xffffff80158f3fef
0xffffff80ae9e3d80 : 0xffffff7f973e0676
0xffffff80ae9e3e70 : 0xffffff7f973df8d9
0xffffff80ae9e3f30 : 0xffffff80158ddb0c
0xffffff80ae9e3f50 : 0xffffff801583758a
0xffffff80ae9e3f90 : 0xffffff80158378d8
0xffffff80ae9e3fb0 : 0xffffff80158d7417
Kernel Extensions in backtrace:
com.apple.driver.AppleIntelCPUPowerManagement(217.92.1)[CF28958D-CA8A-3A79-911C -78217F5DDAF2]@0xffffff7f973dd000->0xffffff7f97407fff
BSD process name corresponding to current thread: kernel_task
Mac OS version:
13E28
Kernel version:
Darwin Kernel Version 13.3.0: Tue Jun 3 21:27:35 PDT 2014; root:xnu-2422.110.17~1/RELEASE_X86_64
Kernel UUID: BBFADD17-672B-35A2-9B7F-E4B12213E4B8
Kernel slide: 0x0000000015600000
Kernel text base: 0xffffff8015800000
System model name: iMac8,1 (Mac-F226BEC8)
System uptime in nanoseconds: 53277101593110
last loaded kext at 52049652796768: com.apple.macos.driver.AppleUSBEthernetHost 7.0 (addr 0xffffff7f97bb0000, size 28672)
last unloaded kext at 52408741345770: com.apple.macos.driver.AppleUSBEthernetHost 7.0 (addr 0xffffff7f97bb0000, size 20480)
loaded kexts:
net.telestream.driver.TelestreamAudio 1.1.0
com.apple.filesystems.smbfs 2.0.2
com.apple.filesystems.autofs 3.0
com.apple.driver.AppleBluetoothMultitouch 80.14
com.apple.driver.AppleHWSensor 1.9.5d0
com.apple.driver.AppleHDA 2.6.3f4
com.apple.driver.ACPI_SMC_PlatformPlugin 1.0.0
com.apple.driver.AudioAUUC 1.60
com.apple.iokit.IOUserEthernet 1.0.0d1
com.apple.iokit.IOBluetoothSerialManager 4.2.6f1
com.apple.Dont_Steal_Mac_OS_X 7.0.0
com.apple.driver.AppleHWAccess 1
com.apple.driver.AppleBacklight 170.3.5
com.apple.driver.AppleSMCPDRC 1.0.0
com.apple.iokit.BroadcomBluetoothHostControllerUSBTransport 4.2.6f1
com.apple.driver.AppleLPC 1.7.0
com.apple.driver.AppleUpstreamUserClient 3.5.13
com.apple.driver.AppleMCCSControl 1.2.5
com.apple.kext.AMDFramebuffer 1.2.4
com.apple.ATIRadeonX2000 8.2.4
com.apple.kext.AMD2600Controller 1.2.4
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeLZVN 1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.BootCache 35
com.apple.driver.AppleIRController 325.7
com.apple.iokit.SCSITaskUserClient 3.6.6
com.apple.driver.XsanFilter 404
com.apple.iokit.IOAHCIBlockStorage 2.6.0
com.apple.driver.AppleUSBHub 683.4.0
com.apple.iokit.AppleYukon2 3.2.3b1
com.apple.driver.AppleIntelPIIXATA 2.5.1
com.apple.driver.AppleUSBEHCI 660.4.0
com.apple.driver.AirPortBrcm43224 700.36.24
com.apple.driver.AppleFWOHCI 5.0.2
com.apple.driver.AppleAHCIPort 3.0.5
com.apple.driver.AppleUSBUHCI 656.4.1
com.apple.driver.AppleRTC 2.0
com.apple.driver.AppleHPET 1.8
com.apple.driver.AppleACPIButtons 2.0
com.apple.driver.AppleSMBIOS 2.1
com.apple.driver.AppleACPIEC 2.0
com.apple.driver.AppleAPIC 1.7
com.apple.driver.AppleIntelCPUPowerManagementClient 217.92.1
com.apple.nke.applicationfirewall 153
com.apple.security.quarantine 3
com.apple.driver.AppleIntelCPUPowerManagement 217.92.1
com.apple.kext.triggers 1.0
com.apple.driver.IOBluetoothHIDDriver 4.2.6f1
com.apple.driver.AppleMultitouchDriver 245.13
com.apple.driver.DspFuncLib 2.6.3f4
com.apple.vecLib.kext 1.0.0
com.apple.driver.AppleHDAController 2.6.3f4
com.apple.iokit.IOHDAFamily 2.6.3f4
com.apple.driver.IOPlatformPluginLegacy 1.0.0
com.apple.iokit.IOAudioFamily 1.9.7fc2
com.apple.kext.OSvKernDSPLib 1.14
com.apple.iokit.IOSurface 91.1
com.apple.iokit.IOSerialFamily 10.0.7
com.apple.iokit.IOBluetoothFamily 4.2.6f1
com.apple.driver.AppleBacklightExpert 1.0.4
com.apple.iokit.IOBluetoothHostControllerUSBTransport 4.2.6f1
com.apple.iokit.IOFireWireIP 2.2.6
com.apple.driver.AppleSMC 3.1.8
com.apple.driver.IOPlatformPluginFamily 5.7.1d6
com.apple.driver.AppleSMBusController 1.0.12d1
com.apple.iokit.IONDRVSupport 2.4.1
com.apple.kext.AMDSupport 1.2.4
com.apple.AppleGraphicsDeviceControl 3.6.22
com.apple.iokit.IOGraphicsFamily 2.4.1
com.apple.driver.AppleUSBHIDKeyboard 170.15
com.apple.driver.AppleHIDKeyboard 170.15
com.apple.iokit.IOUSBHIDDriver 660.4.0
com.apple.iokit.IOSCSIBlockCommandsDevice 3.6.6
com.apple.iokit.IOUSBMassStorageClass 3.6.0
com.apple.driver.AppleUSBMergeNub 650.4.0
com.apple.driver.AppleUSBComposite 656.4.1
com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.6.6
com.apple.iokit.IOBDStorageFamily 1.7
com.apple.iokit.IODVDStorageFamily 1.7.1
com.apple.iokit.IOCDStorageFamily 1.7.1
com.apple.iokit.IOATAPIProtocolTransport 3.5.0
com.apple.iokit.IOSCSIArchitectureModelFamily 3.6.6
com.apple.iokit.IOUSBUserClient 660.4.2
com.apple.iokit.IOATAFamily 2.5.2
com.apple.iokit.IO80211Family 640.36
com.apple.iokit.IONetworkingFamily 3.2
com.apple.iokit.IOFireWireFamily 4.5.5
com.apple.iokit.IOAHCIFamily 2.6.5
com.apple.iokit.IOUSBFamily 683.4.0
com.apple.driver.AppleEFINVRAM 2.0
com.apple.driver.AppleEFIRuntime 2.0
com.apple.iokit.IOHIDFamily 2.0.0
com.apple.iokit.IOSMBusFamily 1.1
com.apple.security.sandbox 278.11.1
com.apple.kext.AppleMatch 1.0.0d1
com.apple.security.TMSafetyNet 7
com.apple.driver.AppleKeyStore 2
com.apple.driver.DiskImages 371.1
com.apple.iokit.IOStorageFamily 1.9
com.apple.iokit.IOReportFamily 23
com.apple.driver.AppleFDEKeyStore 28.30
com.apple.driver.AppleACPIPlatform 2.0
com.apple.iokit.IOPCIFamily 2.9
com.apple.iokit.IOACPIFamily 1.4
com.apple.kec.corecrypto 1.0
com.apple.kec.pthread 1
Model: iMac8,1, BootROM IM81.00C1.B00, 2 processors, Intel Core 2 Duo, 2.66 GHz, 4 GB, SMC 1.29f1
Graphics: ATI Radeon HD 2600 Pro, ATI Radeon HD 2600 Pro, PCIe, 256 MB
Memory Module: BANK 0/DIMM0, 2 GB, DDR2 SDRAM, 800 MHz, 0x7F98000000000000, 0x202020202020202020202020202020202020
Memory Module: BANK 1/DIMM1, 2 GB, DDR2 SDRAM, 800 MHz, 0x7F98000000000000, 0x202020202020202020202020202020202020
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8C), Broadcom BCM43xx 1.0 (5.10.131.36.16)
Bluetooth: Version 4.2.6f1 14216, 3 services, 22 devices, 1 incoming serial ports
Network Service: Ethernet, Ethernet, en0
Network Service: WiFi, AirPort, en1
Serial ATA Device: Hitachi HDP725032GLA380, 320,07 GB
Parallel ATA Device: OPTIARC DVD RW AD-5630A
USB Device: Keyboard Hub
USB Device: Apple Keyboard
USB Device: SimpleDrive USB 2.0
USB Device: Built-in iSight
USB Device: BCM2046A
USB Device: IR Receiver
Thunderbolt Bus:Based on other users asking for help with crashes - looks like you don't have enough RAM to run Maverick and other applications at the same time.
Find Apple has not been clear on what you should do before you upgrade - including finding out what software needs to be upgraded to work with mavericks and exactly how much RAM you need.
seems 4GB is just not enough. -
I Installed windows with bootcamp on my imac, with the support software(drivers,etc).
Windows works perfectly appart from the usb hubs.
Can anyone help me?Hello,
Are these the built in hubs, or external ones?
If external, are they bus powered or do they have their own AC power? -
I downloaded the new version of iTunes today-it doesn't recognize my shuffles-the older version did. Can you help?
Ok people after messing up three days with my jailbroken ipod touch cauze my itunes didn't recognize it i figured out that the problem is first windows recognized it as a imaging device o as a camera, i found in the device manager was listed mi apple ipod under portable devices and there was the problem it has to be listed under universal serial bus controllers named as a apple ipod so this is what i did but first make sure u have correctly installed itunes and the apple mobile device support:
1 open the device manager or windows button + r is run and then type devmgmt.msc
2 look for the portable devices and find the apple ipod or wherever that is listed on your pc.
3 once u find the apple ipod do a right click on it and click on uptade driver software
4 take the manualy opcion or browse on my computer and then look for this folder on your computer C:\Program Files\Common Files\Apple\Mobile Device Support\Drivers
there should be the driver that itunes recognize and your windows wont recognize your ipod as a camera again but i repeat u have to make sure u have installed the apple mobile device support u can get it by extracting the itunes+quicktime package using winrar. so click on update or next what ever on the update process and next time itunes will open your ipod for sincying thanks to forums ilounge.com -
Can anyone help with these kernel panics?
I work for the NHS. Have spent most of my salary on Adobe Premiere Pro using a Intel Core Mac OS 10.5.8 which is supposed to be enough for the system requirements. Have spent all day shutting down my computer unable to start the software. If it does start it freezes and tells me to restart. This is not acceptable. Can anyone help??? Adobe cefrtai nly don't want to is there ahtyone out there with any solutions? I ahve checked the hard drive it is fine, have done all the usual checks to no avail. Cannot find anywhere to talk to Adobe, their website is a minefield of Groundhog Day!
I have the same problem with Photoshop purchased last year as part of a creative package. This is really annoying!Dear Wonderspark,
I am back at my iMac. Here are the details of my hardware.
Model Name:
iMac
Model Identifier:
iMac7,1
Processor Name:
Intel Core 2 Duo
Processor Speed:
2.4 GHz
Number Of Processors:
1
Total Number Of Cores:
2
L2 Cache:
4 MB
Memory:
3 GB
Bus Speed:
800 MHz
Boot ROM Version:
IM71.007A.B03
SMC Version (system):
1.20f4
Serial Number (system):
W88035L3X86
Hardware UUID:
00000000-0000-1000-8000-001EC205D8B9
Chipset Model:
ATI,RadeonHD2600
Type:
Display
Bus:
PCIe
PCIe Lane Width:
x16
VRAM (Total):
256 MB
Vendor:
ATI (0x1002)
Device ID:
0x9583
Revision ID:
0x0000
ROM Revision:
113-B2250F-219
EFI Driver Version:
01.00.219
Displays:
iMac:
Resolution:
1680 x 1050
Depth:
32-Bit Color
Core Image:
Hardware Accelerated
Main Display:
Yes
Mirror:
Off
Online:
Yes
Quartz Extreme:
Supported
Built-In:
Yes
The software versionas are as follows.
Adobe Photoshop CS5 version 12.0.4
Adobe Premiere Pro CS 5.5 version 5.5.0
I hope that is more use. As I said, the software is successfully installed, but I cannot open Premiere Pro. Photoshop does open occasionally but rather like Russian roulette.
I also have the Creative suite and Dreamweaver is no problem, neither is Indesign. This makes no sense to me I would be grateful for any help. I have checked the hardware and the system is ok. I have tried re-installing the software after un-installing it but that made no difference. I obviously have turned the machine on and off because of the black veil that descends upon the screen during the kernel panic. Premiere Pro has alo frozen everything rather than causing a panic too. HELP! -
I have the latest iTunes, but it keeps closing itself! Can anyone help me?
I have the latest iTunes, but it keeps closing itself! Can anyone help me?
Hello,
Leopard requirements/10.5.x...
* Mac computer with an Intel, PowerPC G5, or PowerPC G4 (867MHz or faster) processor
minimum system requirements
* 512MB of memory (I say 1.5GB for PPC at least, 2-3GB minimum for IntelMacs)
* DVD drive for installation
* 9GB of available disk space (I say 30GB at least)
Classic/OS9 Apps no longer supported.
Trouble is Apple no longer sells it, check eBay & such for the Retail version, not the Gray Discs...
http://www.ebay.com/sch/i.html?_nkw=mac+os+x+leopard+retail+10.5
There are workarounds if the 867MHz CPU is the only hangup...
http://sourceforge.net/projects/leopardassist/
http://lowendmac.com/osx/leopard/unsupported.html
So we know more about it...
At the Apple Icon at top left>About this Mac, report the version of OSX from that window, then click on More Info, then click on Hardware> and report this upto but not including the Serial#...
Hardware Overview:
Model Name: eMac
Model Identifier: PowerMac6,4
Processor Name: PowerPC G4 (1.2)
Processor Speed: 1.42 GHz
Number Of CPUs: 1
L2 Cache (per CPU): 512 KB
Memory: 2 GB
Bus Speed: 167 MHz
Boot ROM Version: 4.9.2f1 -
Can we monitor the CAN bus load through a vi
Is there a way to monitor the CAN bus load through a vi? I am using USB 8473 to establish a CAN communication.
Thank You,
-RaghuHi Raghu,
Are you referring to fuctionality similar to the percentage bus load the NI CAN Bus Monitor shows?
If so, there are no built-in LabVIEW VIs that access this information. You would have to use the available CAN VIs and implement it yourself.
Alternativly, if you only need this for testing, you can use another NI CAN device on the bus to monitor the bus load and then simply remove this device for deployment.
Hope this helps! -
Can someone help with Error 4280?
Hi-
I am getting Error Code 4280 every time I try to burn a cd. Can someone help me get past this?
John
Here are my diagnostics:
Microsoft Windows XP Home Edition Service Pack 2 (Build 2600)
Dell Computer Corporation Dimension 2400
iTunes 6.0.4.2
CD Driver 2.0.4.3
CD Driver DLL 2.0.3.2
LowerFilters: Pfc (2.5.0.204), PxHelp20 (2.0.0.0), Cdr4_xp (5.3.4.21),
UpperFilters: pwd_2k (5.3.4.59), Cdralw2k (5.3.4.21), GEARAspiWDM (2.0.4.3),
Video Driver: Intel(R) 82845G/GL/GE/PE/GV Graphics Controller\Intel(R) 82845G /GL/GE/PE/GV Controller
IDE\DiskWDCWD2500JB-00GVA0____________________08.02D08, Bus Type ATA, Bus Address [1,0]
IDE\DiskWDCWD800BB-75CAA0_____________________16.06V16, Bus Type ATA, Bus Address [0,0]
IDE\CdRomHL-DT-STDVD-ROM_GDR8162B_______________0015___, Bus Type ATA, Bus Address [0,0]
IDE\CdRomNEC_CD-RW_NR-9300A_____________________105B___, Bus Type ATA, Bus Address [1,0]
If you have multiple drives on the same IDE or SCSI bus, these drives may interfere with each other.
Some computers need an update to the ATA or IDE bus driver, or Intel chipset. If iTunes has problems recognizing CDs or hanging or crashing while importing or burning CDs, check the support site for the manufacturer of your computer or motherboard.
Current user is administrator.
D: HL-DT-ST DVD-ROM GDR8162B, Rev 0015
Drive is empty.
E: _NEC CD-RW NR-9300A, Rev 105B
Media in drive is blank.
Get drive speed succeeded.
The drive CDR speeds are: 4 8 16 24 32 40 48.
The drive CDRW speeds are: 4 8 16 24.
The last failed audio CD burn had error code 4280(0x000010b8). It happened on drive E: _NEC CD-RW NR-9300A on CDR media at speed 48X.Hi JKost,
This error is usually a "Optical Power Calibration error" and can be caused by software conflicts, a firmware that needs to be updated, or a blank CD that the drive cannot read/write too (Not all drives are compatible with all brands of blank CDs sad to say)
I tried to look for your exact CD burning model on the dell site for a "Dimension 2400" but didn't see an exact model matching "NEC CD-RW NR-9300A" so if it is a burner that came with the PC when you bought it, you will have to goto the dell site www.dell.com to download the correct firmware update. If its one you had installed after you bought the PC, then goto the NEC site for the update www.NEC.com -
Can anyone help me with Bakcing up my MacBook Pro???
Can anyone help me with Bakcing up my MacBook Pro???
Assuming you're looking for recommendations rather than experiencing specific problems, I would advise the following:
Buy 2 external hard disks. You don't say what model of MBP you have, but I would suggest buying the fastest type of drive your MBP supports. So, instead of going for a cheap USB2 drive, I would consider FW800 or Thunderbolt if your MBP supports it. It might cost more but will be faster.
One of the drives needs to be only as big as your internal HD. (Technically, it only needs to be as big as the amount of data you want to back up but to be safe, get one that matches your HD size). This HD can be used for a Bootable Clone. I use SuperDuper from Shirt Pocket, and a Freecom 1GB FireWire 800 drive. You can try it out for free, but it's worth buying a licence because once it's licenced you can do 'smart backups' where it only needs to copy files that have changed. The free version will have to do an entire clone each time which takes longer.
The second drive you should use as a Time Machine backup. The bigger this is, the more backups you can keep, so the further back in time you can go.
The reason to have both is that they both do different things.
SuperDuper is great for doing a complete 'emergency' backup every so often (i.e. before you go away, or at the end of each week, whatever). This disk means that if your MBP is lost, stolen or the HD goes pop, you can recover pretty much the whole system immediately, because you can boot from that drive on any Intel Mac that supports your bus type and OS version. I do an SD clone every so often and keep it hidden, in case anything happens to my MBP.
Time Machine backups are NOT bootable. However, in an emergency you can do a clean install of your OS and then get everything back by migrating from your last TM backup. But the best and most common use of TM backups is simply 'turning back the clock', i.e. you deleted something you wished you hadn't, or even saved over a piece of work you didn't mean to, or installed some software that has caused problems. As long as there was a recent TM backup, you can just get the older version of that file, or revert your whole system. I carry my TM drive around with me in my laptop bag and have it sat there attached and backing up the whole time I'm working.
Well worth having both strategies in place.
As an aside, if you keep confidential files (client or personal) on your MBP and carry it around somewhere like London as I do, it's also worth considering using FileVault so if your lappy gets nicked you don't have to worry about them getting at all your info. And if you have a clone at home, in the worst instance, all you really have to worry about is just buying a new laptop and restoring it. Expensive, sure, but at least your data is safe. -
Why is it every time I try to buy itunes I am diverted to the Chinese store and cannot pay for my items? Can anyone help? I have tries to select the English store but it will not allow me to proceed. I think it has been hacked in the past as there is a list of Chinese Apps which it seems to be awaiting payment for, going back to 2011.
Free Disk Space & Memory are 2 differen't things.
At the Apple Icon at top left>About this Mac, click on the text below Mac OS X where it says Version 10.4.x and report the Build# please.
Then click on More Info>Hardware and report this upto but not including the Serial#...
Hardware Overview:
Model Name: iMac
Model Identifier: iMac7,1
Processor Name: Intel Core 2 Duo
Processor Speed: 2.4 GHz
Number Of Processors: 1
Total Number Of Cores: 2
L2 Cache: 4 MB
Memory: 4 GB
Bus Speed: 800 MHz
Boot ROM Version: IM71.007A.B03
SMC Version (system): 1.21f4
Then we cn tell you huw to add more RAM & which is the correct RAM Memory. -
Can some1 help me with my bootcamp...It crashed?
Dear all,
Can someone help me with my bootcamp? it crashed....
Thanks,
Dap
Process: Boot Camp Assistant [286]
Path: /Applications/Utilities/Boot Camp Assistant.app/Contents/MacOS/Boot Camp Assistant
Identifier: com.apple.bootcampassistant
Version: ???
Build Info: BootCampAssistant-5317000000000000~145
Code Type: X86-64 (Native)
Parent Process: launchd [171]
Responsible: Boot Camp Assistant [286]
User ID: 501
Date/Time: 2014-01-22 14:51:06.920 +0800
OS Version: Mac OS X 10.9.1 (13B42)
Report Version: 11
Anonymous UUID: 0679BA59-0EAC-CA3B-7CB7-32F32AD12B39
Crashed Thread: 0
Exception Type: EXC_CRASH (Code Signature Invalid)
Exception Codes: 0x0000000000000000, 0x0000000000000000
VM Regions Near 0x7fff795660a8 (cr2):
__LINKEDIT 00007fff674b7000-00007fff674cb000 [ 80K] r--/rwx SM=COW /usr/lib/dyld
--> Submap 00007fff70000000-00007fff80000000 [256.0M] r--/rwx SM=PRV process-only VM submap
unused shlib __DATA 00007fff77856000-00007fff7a062000 [ 40.0M] rw-/rw- SM=COW system shared lib __DATA not used by this process
Thread 0 Crashed:
0 dyld 0x00007fff67445028 _dyld_start + 0
Thread 0 crashed with X86 Thread State (64-bit):
rax: 0x000000000000000d rbx: 0x0000000000000000 rcx: 0x0000000000000000 rdx: 0x0000000000000000
rdi: 0x0000000000000000 rsi: 0x0000000000000000 rbp: 0x0000000000000000 rsp: 0x00007fff59e08cf0
r8: 0x0000000000000000 r9: 0x0000000000000000 r10: 0x0000000000000000 r11: 0x0000000000000000
r12: 0x0000000000000000 r13: 0x0000000000000000 r14: 0x0000000000000000 r15: 0x0000000000000000
rip: 0x00007fff67445028 rfl: 0x0000000000000201 cr2: 0x00007fff795660a8
Logical CPU: 0
Error Code: 0x020000f4
Trap Number: 133
Binary Images:
0x7fff67444000 - 0x7fff67477817 dyld (???) <D1DFCF3F-0B0C-332A-BCC0-87A851B570FF> /usr/lib/dyld
External Modification Summary:
Calls made by other processes targeting this process:
task_for_pid: 0
thread_create: 0
thread_set_state: 0
Calls made by this process:
task_for_pid: 0
thread_create: 0
thread_set_state: 0
Calls made by all processes on this machine:
task_for_pid: 149
thread_create: 0
thread_set_state: 0
VM Region Summary:
ReadOnly portion of Libraries: Total=288K resident=268K(93%) swapped_out_or_unallocated=20K(7%)
Writable regions: Total=8444K written=0K(0%) resident=12K(0%) swapped_out=0K(0%) unallocated=8432K(100%)
REGION TYPE VIRTUAL
=========== =======
STACK GUARD 56.0M
Stack 8192K
VM_ALLOCATE 8K
VM_ALLOCATE (reserved) 4K reserved VM address space (unallocated)
__DATA 252K
__LINKEDIT 80K
__TEXT 208K
mapped file 216K
shared memory 4K
=========== =======
TOTAL 64.8M
TOTAL, minus reserved VM space 64.8M
Model: MacBookPro9,2, BootROM MBP91.00D3.B09, 2 processors, Intel Core i5, 2.5 GHz, 4 GB, SMC 2.2f44
Graphics: Intel HD Graphics 4000, Intel HD Graphics 4000, Built-In, 1024 MB
Memory Module: BANK 0/DIMM0, 2 GB, DDR3, 1600 MHz, 0x02FE, 0x45424A3230554638424455302D474E2D4620
Memory Module: BANK 1/DIMM0, 2 GB, DDR3, 1600 MHz, 0x02FE, 0x45424A3230554638424455302D474E2D4620
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0xF5), Broadcom BCM43xx 1.0 (5.106.98.100.22)
Bluetooth: Version 4.2.0f6 12982, 3 services, 23 devices, 1 incoming serial ports
Network Service: Wi-Fi, AirPort, en1
Serial ATA Device: APPLE HDD ST500LM012, 500.11 GB
Serial ATA Device: MATSHITADVD-R UJ-8A8
USB Device: Hub
USB Device: Cruzer Blade
USB Device: FaceTime HD Camera (Built-in)
USB Device: Hub
USB Device: iPhone
USB Device: Hub
USB Device: Apple Internal Keyboard / Trackpad
USB Device: IR Receiver
USB Device: BRCM20702 Hub
USB Device: Bluetooth USB Host Controller
Thunderbolt Bus: MacBook Pro, Apple Inc., 25.1The email you should NOT have published, is your iCloud, not Apple ID
You Apple ID is a valid email address
This is a user forum, not Apple customer service.
I gather the security question did not work.
If you have an email address, why not use that?
If this fails you have to contact support and schedule help. -
Interacing Labview with a CAN bus interface
I should use a CAN parallel/serial interface produced by
ACTIA(NetPorty II) and i'm using Win XP and LV 6.1. What is the
simplest method to use it in a "user friendly" way (i'd like to avoid
writing a driver myself)?
Does anyone of you own the same card and/or must face similar
problems??
If you want you can answer me via e-mail...
Thank you in advance,
LucaThank you for your answer, i'll try to work at it...i'm a novice!
On Tue, 4 Mar 2003 15:58:08 -0600 (CST), DiegoF wrote:
>Hi,
>
>It really depends on the software the manufacturer provides to handle
>this device.
>
>If the manufacturer provides an API that exports the CAN bus specific
>functions and internally handles the parallel or serial communication,
>it would be recommended to use this API. Most likely the API will
>have a C interface, so you can use the library function call nodes to
>access these functions.
>
>If the manufacturer only provides a list of command you need to send
>to the device, then the problem is no different from communicating
>this other devices (like scopes, DMM). basically, you can use VISA
>to send the required com
mands to the device.
>
>Hope this helps.
>
>DiegoF.
>National Instruments.
Maybe you are looking for
-
Sending E-mail to Business Partner from Web IC
Hi Folks, I am having some questions regarding sending an e-mail to a Business Partner (BP) from the Web IC 5.0. When identifying a BP and then go to the work area of E-mail and selecting an email form/template we get different information populated
-
What is the best way to configure storage device for rac?
Hi On my disk array i have 7mirors and two conroler, what is the best way to configure environment? My application is OLTP, it runs 6-20 o clocj, so i can do backup when nobady work Database 10g r2, Windows 2003 enterpise for examlep First controler
-
Urgent: problem finding version 51031897 at market place
Hi guys, when iam insatlling ecc6.0 , i found problem during import abap phase due to SAPSSEXC_9.002 in my exp4 data . I tried to download it from marketplace, but i couldnot found the correct version 51031897. please can any one help me in this rega
-
Xserve Raid - moving raid set from one Xserve Raid to another Xserve Raid.
I have 2 raids, and one will be moving to another building. Can I take one raid set out of unit 1 and place it into unit 2 without losing the data that is on it?
-
CIE chromacity graph in labview
Has anyone ever implemented CIE chromacity graph in labview. Please let me know how to approach this problem.