Can't access FTP server to download tftp.exe file

I am trying to update the firmware on my WRT54GS v5 router.  I had no problem downloading the firmware, but can't access the FTP site for the TFTP.EXE file.  It won't work in IE or Firefox.  I can't get it through my router, or wireless thorugh my neighbor's router.
What should I try? 

To download the TFTP.exe file on your computer click Here.
Once you download the TFTP file on your computer, now connect your computer to the Linksys router and Follow the instruction below. 
Double click the TFTP.exe file and click run.
For Server- Enter the IP Address of the router that you assigned.  By default, the router is 192.168.1.1...
For Password- Enter the password you assigned the router. By default, the router’s password is “admin”.
For File- Click the triple “…” button and browse for the .bin firmware file...
Click Upgrade button to start upgrading.  A progress bar should show up to show the progress.
Once the Upgrade is done press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

Similar Messages

  • Can't access FTP server OR the SITE!

    I installed dreamweaver and succesfully mapped it to my FTP server. I was in the middle of a sync between my remote and local folders when the connection was dropped! It would not reconnect, I found out a few minutes later that I could not even access the web page itself, or the hosting server, of the ftp directory. NOTHING! However, my roommate can access all of the fine from his PC. I am a new MAC user and was wondering if there was some bandwidth limit I have exceeded or something. I turned the firewall off and everything! AHHH. I'm losing my mind here. Someone pleasse tell how to fix this.

    Problem solved. The issue was the FTP Client I was using *****. It opened over 50 simultaneous connections with the server and the server firewall blocked my IP.

  • I'm signed in, I have my serial number, but the system won't allow me to access the server to download a replacement for my premiere eolements 10. What am I doing wrong?

    I lost my hard drive and am replacing a lot orf software on the new one.software. Bah!
    But Adobe premiere 10 won't allow me to access the server to download a replacemet.
    What am I doing wrong?

    Make sure you have cookies enabled and clear your cache.  If it continues to fail try using a different browser.
    PSE 10, 11, 12 - http://helpx.adobe.com/photoshop-elements/kb/photoshop-elements-10-11-downloads.html
    You can also download the trial version of the software thru the page linked below and then use your current serial number to activate it.
    Be sure to follow the steps outlined in the Note: Very Important Instructions section on the download pages at this site and have cookies enabled in your browser or else the download will not work properly.
    Photoshop/Premiere Elements 10: http://prodesigntools.com/photoshop-elements-10-direct-download-links-pse-premiere-pre.htm l

  • How can i access dmz server via public ip from inside?

    hi all !
    As shown in Figure，how can i access the server in dmz zone via public？
    i can access it via private ip 192.168.1.1 now,but i can't access it via 101.100.1.2.
    who can help me ?
    thank you !

    Hi,
    You would have to configure Static NAT from DMZ to INSIDE for the server in the same way you have done for DMZ to OUTSIDE.
    Basically in the following way for example
    object network DMZ-WEB
    host 192.168.1.1
    nat (dmz,inside) static 101.100.1.2
    This would enable your users on the "inside" to access the "dmz" server with the public IP address. And naturally only with the public IP address after this NAT.
    Hope this helps
    Please do remember to mark a reply as the correct answer if it answered your question.
    Feel free to ask more if needed
    - Jouni

  • Can't Access the Server RootDSE

    Hi All,
    I am working on Windows platform and trying to create a directory instance in Sun Directory Server 6.0 using its commandline utility dsadmin by executing the following command:
    dsadm create - h localhost -p 2389 -P 1064 D:\Temp\SUNDS_TEMPthen strat the instance as:
    dsadm start D:\Temp\SUNDS_TEMPThe instance gets created successfully but when I try to access the instance using an LDAP browset it gives me error:
    Can't Access the Server RootDSE
    Error Code: 32
    Error Message: No Such Object
    I am creating this instance to use as Access Manager configuration store. Is anybody aware of this issue?
    Thanks,
    Tariq Chauhdary

    Thank you very much all. I was able to resolve this issue.
    I did not create the Suffix and LDAP browser and that was the reason for LDAP browser to raise RootDSE error.

  • I can not accessed J2EE Server because i dont know username and password

    I set username and password as tutorials but not successful.
    and after that i can't access J2EE server with localhost:4848.
    please tell me the way access J2EE server.Or Default username and password of it.
    Thanks your help!

    Hi,
    Can you please send more infomation on exactly what is failing? Are you trying to execute asadmin commands?
    Also, which platform are you running the appserver on? Does the appserver show up in the list of currently running processes?
    I believe that the default username is "admin" and the password is "adminadmin".
    Thanks,
    Kyle

  • EA6500 - unable to setup Folder Access / FTP Server / Media Server functions

    I purchased the EA6500 a few days ago, and when I'm connected to Cisco Connect Cloud I am unable to select Folder Access / FTP Server / Media Server.  I click them and nothing happens.
    Also, the Cisco light on the router keeps blinking.  I'm googling to find out how to troubleshoot these situations but I'm having no luck.
    I appreciate any help with these situations.

    DoublePromo wrote:
    I contacted customer service, and they helped me troubleshoot.  The description of the router and it's capabilites appears misleading to me - "Folder Access" - I thought it gave one the capability to file share between different computers that are on the same network.  It's only for files that are on a USB stick that's connected to the router.  Oh well.  Good thing I still have Network Magic Pro.
    In addition to this, storage functionality on the router doesn't need any software for it to work. The router should be able to detect the external drive when connected and get it configured on the router's interface unlike network magic which you've mentioned where the program must be installed to all computers in the network for it to be able to see all devices present in the network and share files and folders through it.

  • SSRS 2005 why some users can't access report server.

    There is one user who can't access report server by clicking a link to a report. A window will pop up asking for login. Even he enters login, the window will keep coming back. I have set the user for that report and assigned the 'Browser' role to the user.
    Other users don't have this problem. E.g. for another user I also set him up for the report and assigned 'Browser' role but he can access the same report no problem.

    Hi thotwielder,
    As per my understanding, I think this issue can be caused by the following two reasons:
    The report server can be blocked by Firewall. If Windows Firewall is turned on, the port that the report server is configured to use is most likely closed. Indications that a port might be closed are the appearance of a blank Web page after requesting a
    report, or a blank page when you attempt to open Report Manager from a remote client computer. In this scenario, we can try to open port 80 in Windows Firewall on both report server and client computers.
    The report server can be blocked by browser. We should ass the report server URL to trusted site in the browser.
    We can also grant the user access to site-wide operations with system-level row in report manager to check the issue again.
    Please double-check we have been grand the user the browser role on the report. We can navigate to Security property of the report to check the issue.
    Reference:
    Configure a Firewall for Report Server Access
    Configure a Native Mode Report Server for Local Administration (SSRS)
    Grant User Access to a Report Server (Report Manager)
    Thanks,
    Katherine Xiong
    Katherine Xiong
    TechNet Community Support

  • BEFW11S4 v4: Cannot download tftp.exe from LinkSys website

    Hello all!
         I am a brand new user to this forum.  I have seen much valuable information here, so I KNOW someone has the answer to my little problem.
         The Power LED on my trusty BEFW11S4 v4 is blinking and nothing I have tried to fix the problem has worked.  I have downloaded the latest firmware (1.52.03) but I cannot get to the router's setup page.  So the LinkSys website says you can go in the back door using their tftp.exe routine.  Problem is, every time I try to download it I get a "Cannot connect" error message from Windows.
         Does anyone know where I can download the correct tftp.exe file for my unit so I can try to upgrade the firmware?
         Thanks in advance for any help you might can give me. 
    Solved!
    Go to Solution.

    Thank you very much for the link to the download.  I am on the road right now, but I will try this fix as soon as I return.  I will let every one know how it comes out.  Thanks again!

  • How Can i specify multiple server names in rwservlet.properties  file?

    How Can i specify multiple server names in rwservlet.properties file without clustering?
    I am using oracle 10g Application server. we have 3 servers Repsvr1, RepSvr2 and RepSvr3. Now i need to configure rwservlet.properties file to point to these servers based on any running report. i got 3 keymap files with reports info.
    Sample entry in the key map file is:
    key1: server=Repsvr1 userid=xxx/yyy@dbname report=D:\Web\path1\path2\reports\Report1.rdf destype=cache desformat=PDF %*
    key2: server=Repsvr2 userid=xxx/yyy@dbname report=D:\Web\path1\path3\reports\Report2.rdf destype=cache desformat=PDF %*
    rwservlet.properties file letting me to enter only one servername. Even though i merged all 3 keymap files into 1, still i have the server name issue. If i leave the server to the default name still i am getting the below error.
    REP-51002: Bind to Reports Server Repsvr1 failed. However, i know the default rep_<servername> would be used incase we dont have SERVER=<value> parameter in the rwservlet.properties file.
    If i specify the servername in the rwservlet.properties file then only Repsvr1 reports are working fine and other 2 server reports are giving the same error like
    REP-51002: Bind to Reports Server <<Server Name>> failed.
    how can i configure the info which will work all 3 reports. 2 Port servers are invoking using oracle forms and report server is invoking using ASP pages.
    If i specify Server name & Key map file in rwservlet.properties one at a time, all the reports are working without any error, whenever i am trying to integrate all 3 to workable i am getting binding error. if i exclude the server from rwservlet.properties still i am getting the same error.

    My RELOAD_KEYMAP setting is YES only.As i said If i specify Server name & Key map file in rwservlet.properties one at a time, all the reports are working without any error.
    keymap file entries
    key1: server=Repsvr1 userid=xxx/yyy@dbname report=D:\Web\path1\path2\reports\Report1.rdf destype=cache desformat=PDF %*
    key2: server=Repsvr2 userid=xxx/yyy@dbname report=D:\Web\path1\path3\reports\Report2.rdf destype=cache desformat=PDF %*
    If i use http://server.domain:port/reports/rwservlet? cmdkey = key1 should bring the report from Repsvr1 and http://server.domain:port/reports/rwservlet? cmdkey = key2 should bring the report from Repsvr2, but i am getting an error from Repsvr2 saying that REP-51002: Bind to Reports Server repsvr2 failed.
    Only Servername Repsvr1 is in rwservlet.properties file. Now what is the best option to by pass the server from rwservlet.properties file and should be from keymap file. if i comment server name in rwservlet.properties file still i am getting REP-51002: Bind to Reports Server <<Server Name>> failed error for both keys.

  • I want to uninstall and then reinstall Firefox but I can't uninstall it. Nothing happens when I click remove in program access and defaults and the helper.exe file in the firefox uninstall dir doesn't do anything either.

    I want to uninstall and then reinstall Firefox but I can't uninstall it. Nothing happens when I click remove in program access and defaults and the helper.exe file in the firefox uninstall dir doesn't do anything either.

    "program access and defaults" is not the place to remove programs in Windows. You need to go to the control panel and click on Add and Remove programs. For instructions on how to uninstall Firefox, see [[Uninstalling Firefox]]

  • How do I download a .exe file on my macbook pro?

    I am trying to download a .exe file -- I just switched to a macbook pro from a PC.  help!

    You can download any file you like to your Mac, but you won't be able to run an .exe natively as they're for the Windows operating system.  You could purchase something like Parallels if you want to run Windows software, or alternatively use Boot Camp.
    Hope this helps.

  • "You are about to download an .EXE file" message when downloading

    is there any way to disable this stupid message? Who cares if I am downloading an EXE file for Windows. I don't remember this message in older versions of Safari and I hate it in this one.

    Hi
    Safari 3rd party SAFT has many features, including "stop download warnings". Once installed, most features are accessed via Safari's Preference file.
    You might also try deselecting "open safe files etc." via Safari Preferences>General, however, not sure if that will stop the warnings.

  • How to download and exe file?

    Hi - is there a way for a mac user to download an exe file - I'm needing to download some software from my internet company in Africa - it tracks my usage, important because here we pay per download - thus the software is a program that tracks usage so we don't go over our monthly amount . . . as most things here, there is almost nothing set up for macs . . . hence my query: is there a way to convert an exe file so that I can use it? THANKS, Autumn

    Hi Masego
    Downloading is easy - but if it's an exe file then you might not be able to make much use of it on OS X, as it won't run.
    To run Windows exe files on a Mac you need one of the following technologies:
    1. A version of Windows installed on a separate partition of your hard disk, using Boot Camp.
    2. A version of Windows installed using a virtualisation technology, such as Virtual Box.
    3. I'm told that "Mono" will allow you to run certain exe files under OS X but I've never tried it myself.  Mono is free and if you do a search for it then you might find someone who can give you more support.
    Bob

  • When i download an ".exe" file the only option i'm given is to save; i want to be able to run

    when i want to download an ".exe" file i'm not given the option to run, only save. i want run option.

    I understood the security reasons for not making it a default but didn't see why it should be completely removed, just put warnings on the option if needed.
    re download: yes I realise that at least it's to a temp area that can be cleaned up. All I care about is that I click and it runs, I do not want to worry about saving it, bringing up Windows Explore, finding it and then clicking on it again to run it.
    Thanks a lot for the help, I hope Firefox won't dumb down the products to the lcd. It's tricky to design something that is simple to use but flexible enough to satisfy different requirements if needed but it is worthwhile.

Maybe you are looking for