Cannot access internal network after Tiger upgrade

I've just upgraded an eMac (1.25GHz, 768MB) from 10.3.9 to 10.4.6. Although I can get online, access Mail and all applications, I cannot access the internal network at all.
I've updated to 10.4.9, but still no luck. I've restarted, logged in as a different user, logged out and in again, removed the 'com.apple.networkconfig.plist' file from the 'Library/Preferences' folder, but still doesn't work.
I can see all the aliases to the other machines on the network in the sidebar, but clicking on them brings up a message "The alias xxxx could not be opened, because the original alias could not be found.".
Other machines can see this on on the network. File Sharing is turned on.
Any thoughts, I'm tearing my hair out a bit!
Powerbook G4 Mac OS X (10.4.8)

no good, is an afpmounter error, i solved it with an
Archive and Install
http://docs.info.apple.com/article.html?artnum=107120-en
maybe someone have a solution..
i think is an error during the update (i had the same from panther to tiger)
with A&I and half-hour, your machine work perfectly.

Similar Messages

Cisco ASA 5505 L2TP VPN cannot access internal network

Hi,
I'm trying to configure Cisco L2TP VPN to my office. After successful connection I cannot access to internal network.
Can you jhelp me to find out the issue?
I have Cisco ASA:
inside network - 192.168.1.0
VPN network - 192.168.168.0
I have router 192.168.1.2 and I cannot ping or get access to this router.
Here is my config:
ASA Version 8.4(3)
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 198.X.X.A 255.255.255.248
ftp mode passive
same-security-traffic permit intra-interface
object network net-all
subnet 0.0.0.0 0.0.0.0
object network vpn_local
subnet 192.168.168.0 255.255.255.0
object network inside_nw
subnet 192.168.1.0 255.255.255.0
access-list outside_access_in extended permit icmp any any echo-reply
access-list outside_access_in extended deny ip any any log
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool sales_addresses 192.168.168.1-192.168.168.254
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic net-all interface
nat (inside,outside) source static inside_nw inside_nw destination static vpn_local vpn_local
nat (outside,inside) source static vpn_local vpn_local destination static inside_nw inside_nw route-lookup
object network vpn_local
nat (outside,outside) dynamic interface
object network inside_nw
nat (inside,outside) dynamic interface
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 198.X.X.B 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication enable console LOCAL
aaa authentication ssh console LOCAL
aaa authentication http console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set my-transform-set-ikev1 esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set my-transform-set-ikev1 mode transport
crypto dynamic-map dyno 10 set ikev1 transform-set my-transform-set-ikev1
crypto map vpn 20 ipsec-isakmp dynamic dyno
crypto map vpn interface outside
crypto isakmp nat-traversal 3600
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh timeout 30
console timeout 0
management-access inside
dhcpd address 192.168.1.5-192.168.1.132 inside
dhcpd dns 75.75.75.75 76.76.76.76 interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy sales_policy internal
group-policy sales_policy attributes
dns-server value 75.75.75.75 76.76.76.76
vpn-tunnel-protocol l2tp-ipsec
username ----------
username ----------
tunnel-group DefaultRAGroup general-attributes
address-pool sales_addresses
default-group-policy sales_policy
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:5d1fc9409c87ecdc1e06f06980de6c13
: end
Thanks for your help.

You have to test it with "real" traffic to 192.168.1.2 and if you use ping, you have to add icmp-inspection:
policy-map global_policy
class inspection_default
inspect icmp
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni

Vpn client can access internet but cannot access internal network

I am using PIX 501 to setup a VPN. At first the VPN client cannot access the internet once they logged in via the Cisco system vpn client, so i enable split tunneling. Now the VPN client can access the internet but they can't access the internal network.Due to the limited characters can be posted here, only necessary IOS coding is posted on the next message. Who knows how to solve this problem? Pls Help.....

enable password ********** encrypted
passwd ********** encrypted
hostname Firewall
domain-name aqswdefrgt.com.sg
access-list 100 permit ip 192.168.1.0 255.255.255.0 192.168.50.0 255.255.255.0
access-list nat permit tcp any host 65.165.123.142 eq smtp
access-list nat permit tcp any host 65.165.123.142 eq pop3
access-list nat permit tcp any host 65.165.123.143 eq smtp
access-list nat permit tcp any host 65.165.123.143 eq pop3
access-list nat permit tcp any host 65.165.123.143 eq www
access-list nat permit tcp any host 65.165.123.152 eq smtp
access-list nat permit tcp any host 65.165.123.152 eq pop3
access-list nat permit tcp any host 65.165.123.152 eq www
access-list nat permit tcp any host 65.165.123.143 eq https
access-list nat permit icmp any any
ip address outside 65.165.123.4 255.255.255.240
ip address inside 192.168.1.2 255.255.255.0
ip verify reverse-path interface outside
ip local pool clientpool 192.168.50.1-192.168.50.50
global (outside) 1 interface
nat (inside) 0 access-list 100
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
static (inside,outside) tcp 65.165.123.142 smtp 192.168.1.56 smtp netmask 255.255.2
55.255 0 0
static (inside,outside) tcp 65.165.123.142 pop3 192.168.1.56 pop3 netmask 255.255.2
55.255 0 0
static (inside,outside) tcp 65.165.123.143 smtp 192.168.1.55 smtp netmask 255.255.2
55.255 0 0
static (inside,outside) tcp 65.165.123.143 pop3 192.168.1.55 pop3 netmask 255.255.2
55.255 0 0
static (inside,outside) tcp 65.165.123.143 www 192.168.1.55 www netmask 255.255.255
.255 0 0
static (inside,outside) tcp 65.165.123.152 smtp 192.168.1.76 smtp netmask 255.255.
255.255 0 0
static (inside,outside) tcp 65.165.123.152 pop3 192.168.1.76 pop3 netmask 255.255.
255.255 0 0
static (inside,outside) tcp 65.165.123.152 www 192.168.1.76 www netmask 255.255.25
5.255 0 0
static (inside,outside) tcp 65.165.123.143 https 192.168.1.55 https netmask 255.255
.255.255 0 0
access-group nat in interface outside
route outside 0.0.0.0 0.0.0.0 65.165.123.1 1
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
aaa-server plexus protocol radius
aaa-server plexus (inside) host 192.168.1.55 ******** timeout 5
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
crypto ipsec transform-set myset esp-des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto dynamic-map cisco 1 set transform-set myset
crypto map dyn-map 20 ipsec-isakmp dynamic cisco
crypto map dyn-map client authentication plexus
crypto map dyn-map interface outside
isakmp enable outside
isakmp key ******** address 0.0.0.0 netmask 0.0.0.0
isakmp policy 20 authentication pre-share
isakmp policy 20 encryption des
isakmp policy 20 hash md5
isakmp policy 20 group 2
isakmp policy 20 lifetime 86400
isakmp policy 40 authentication pre-share
isakmp policy 40 encryption 3des
isakmp policy 40 hash md5
isakmp policy 40 group 2
isakmp policy 40 lifetime 86400
vpngroup vpn3000 address-pool clientpool
vpngroup vpn3000 dns-server 192.168.1.55
vpngroup vpn3000 wins-server 192.168.1.55
vpngroup vpn3000 default-domain aqswdefrgt.com.sg
vpngroup vpn3000 idle-time 1800
vpngroup vpn3000 password ********
telnet 192.168.1.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
terminal width 80

Cannot access internal LAN after VPN connect

I know this is either an ACL or NAT issue that I cannot figure out. The nat-t config in defaulted in the IOS config for the ASA. I actually forgot the command to show the hidden default config lines. Either way, can someone take a look at my config, and let me know what I am doing wrong, again.
Thanks ahead of time.
ASA Version 8.2(2)
hostname ciscousa
enable password
names
interface Vlan1
nameif inside
security-level 100
ip address 1.1.1.2 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 14.14.11.5 255.255.255.0
interface Vlan3
shutdown
no forward interface Vlan2
nameif dmz
security-level 50
ip address dhcp
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
speed 100
duplex full
ftp mode passive
same-security-traffic permit intra-interface
access-list outside_in extended permit icmp any any
access-list inside_nat0 extended permit ip any 1.1.1.0 255.255.255.0
access-list inside_nat0 extended permit ip any 10.12.27.0 255.255.255.0
access-list split_tunnel standard permit 1.1.1.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu dmz 1500
ip local pool vpnpool 10.12.27.100-10.12.27.120 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0
nat (inside) 1 0.0.0.0 0.0.0.0
access-group outside_in in interface outside
route outside 0.0.0.0 0.0.0.0 14.14.11.6 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 1.1.1.0 255.255.255.0 inside
http 1.1.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map inet-1_dyn_map 20 set transform-set ESP-3DES-SHA
crypto map inet-1_map 65535 ipsec-isakmp dynamic inet-1_dyn_map
crypto map inet-1_map interface outside
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
management-access inside
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy vpnipsec internal
group-policy vpnipsec attributes
wins-server value 1.1.1.16
dns-server value 1.1.1.16
split-tunnel-policy tunnelspecified
split-tunnel-network-list value split_tunnel
default-domain value company.com
tunnel-group vpnipsec type remote-access
tunnel-group vpnipsec general-attributes
address-pool vpnpool
default-group-policy vpnipsec
tunnel-group vpnipsec ipsec-attributes
pre-shared-key *****
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512

Hello,
I have been trying to get this to work within the last week but to no avail. I changed my config altogether and started from scratch. I have Split Tunnel working well, and I can access the VPN client from the internal LAN. But I still cannot access the internal LAN from the VPN client host. Can anyone take a look at my config and tell me what ACL\Access Group I am missing. I know I am close but I cannot get over the hump.
Thanks!
ASA Version 8.2(2)
names
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.2 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address xxx.xxx.xxx.xxx 255.255.255.0
interface Vlan3
shutdown
no forward interface Vlan2
nameif dmz
security-level 50
ip address dhcp
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
speed 100
duplex full
interface Ethernet0/4
interface Ethernet0/5
switchport access vlan 3
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
access-list outside_in extended permit icmp any any
access-list outside_in_vpn extended permit ip 192.168.3.0 255.255.255.0 any
access-list inside_nat0_outbound extended permit ip 192.168.0.0 255.255.0.0 192.168.0.0 255.255.0.0
access-list split_tunnel standard permit 192.168.0.0 255.255.0.0
access-list split_tunnel standard permit 192.168.1.0 255.255.255.0
access-list inside_access_in extended permit ip any any
access-list outside_access_in extended permit ip any any
pager lines 24
logging enable
logging buffered debugging
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu dmz 1500
ip local pool ipvpn 192.168.3.100-192.168.3.200 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
access-group inside_access_in in interface inside
access-group outside_in in interface outside control-plane
access-group outside_in_vpn in interface outside
route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xx 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map internet-1_dyn_map 20 set transform-set ESP-3DES-SHA
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHAESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map internet-1_map 65535 ipsec-isakmp dynamic internet-1_dyn_map
crypto map internet-1_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto isakmp identity address
crypto isakmp enable inside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
management-access inside
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DfltGrpPolicy attributes
group-policy vpnipsec internal
group-policy vpnipsec attributes
wins-server value 192.168.1.5
dns-server value 192.168.1.5
split-tunnel-policy tunnelall
split-tunnel-network-list value split_tunnel
default-domain value company.com
tunnel-group vpnipsec type remote-access
tunnel-group vpnipsec general-attributes
address-pool ipvpn
default-group-policy vpnipsec
tunnel-group vpnipsec ipsec-attributes
pre-shared-key *
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
prompt hostname context
Cryptochecksum:7e41045c9d7c66ac2c03c3b12ae63908

After upgrading to Mountain Lion I am not able to access "security and privacy" button under "system preferences". I like to activate "find my mac" but cannot access privacy setting after upgrade. Kindly advice.

After upgrading to Mountain Lion I am not able to access "security and privacy" button under "system preferences". I like to activate "find my mac" but cannot access privacy setting after upgrade. Kindly advice.

[network access] User cannot access through network

Hi!
I'm facing a strange problem now.
One of the users of my WD Personal Cloud cannot access through network share. When he tries to login the same fails and the login is prompted again. This happens in Windows but happens also in Linux.
When the same user tries to login in the mobile cloud app or in the browser (only in windows because after all this years the browser cloud funcionality still not works for Linux users, a shame...) it works as it should be.Also i tried to create a new users and happens the same, in the app or browser works great in network share simply refuse to login! I already rebooted, turn off, disconnected and did other things but nothing worked.
There are 9 users and 10 share in he cloud and the firmware version is v04.01.04-422. The diagnosis is OK!
Thanks for the help. Best Regards.

Hi again! There is no error. When i enter the share ask for the login credentials, i insert user and password and when i click ok simply ask the credentials again, and again, and again... It's the same compotment as if the credentials are wrong but they are not, i use them for online login in wd2go.com or mobile app and they work.And another thing is that if i create a new user happens the same, i can login in mobile app and wd2go.com but in the windows share (or samba share if in Linux) it fails without any error, simply ask for the credentials again and again and again... The old users works fine. The comportment is same with IP or name. Thanks for the help, Best Regards.

I have recently unlocked my iPhone 4. I got the comforation saying it was unlocked. For some reason I cannot access my network settings? Any suggestions. I am trying to use the phone on Net 10 network.

I recently unlocked my iphone 4. I am trying to use it on Net 10's network. However, i cannot access the network settings. I have the Net10 Sim already in it. A few notes listed below of what i have tried:
1.) I downloaded the iphone configuation utility. But cannot get the right settings to apply. (so if you have the correct ones i could use those)
2.) i have watched 1000 youtube videos and been on practically every page online and tried 1000 different versions of APN settings through the configuration
3.) I do not have another SIM card from another carrier to try.
Open to suggestions on how i can get the APN settings to change. Not worried about picture messaging or anything, but would like my internet to work. Calls and text work fine.

i have seen this option..problem being...i dont have access to WIFI i live in the middle of ten buck too! We cant even get internet out here i have to go a friend house to get internet. I was going to try that once i did get to town but was looking for other options here at home frist.

Users cannot access removable devices after you enable and then disable a Group Policy setting in Windows 7 64 Bit

Users cannot access removable devices after you enable and then disable a Group Policy setting on Windows 7 64 bit machines.
on the 32 bit machines I was able to apply this hotfix
http://support2.microsoft.com/kb/2738898
But it will not install on 64 bit machines.
Is there a hotfix for 64 bit? If not, what is the work around?
Thanks!
Robert

Select "Show hotfixes for all platforms and languages", then download x64 hotfix:
Please take a moment to Vote as Helpful and/or Mark as Answer where applicable. Thanks.

I cannot access iPhoto now I have upgraded to Yosemite. Not available in UK! What can I do? I have hundreds of photos I need access to and more to save on my computer.

I cannot access iPhoto now I have upgraded to Yosemite. Not available in UK! What can I do? I have hundreds of photos I need access to and more to save on my computer.

iPhoto should be still in your Applications folder and will still work. But if you failed to keep it up to date then Try Terence's instructions here Is Iphoto gone ?i want it back!
Pete

I cannot download sny apps after i upgrade to IOS6 ,message keep telling me ' Your session has timed out. Try again. I need help ��

cannot download sny apps after i upgrade to IOS6 ,message keep telling me ' Your session has timed out. Try again. I need help

From Apple Support...
Here are troubleshooting steps that should help you fix the problem.
1) Quit App Store in multi-tasking.
2) Tap Settings.
3) Tap Safari.
4) Tap Clear History.
5) Tap the Clear History button.
6) Tap Clear Cookies and Data.
7) Tap the Clear Cookies and Data button.
Try purchasing an app again from the device to get the security question prompt. You really need to set up the security question.
...it seems to have worked for me.....

Cannot access my Ipad after downloading latest download. It wont accept my password.

I cannot access my Ipad after downloading latest download. The Ipad wont accept my password. What can I do?

Try the following:
1. Restore:
http://support.apple.com/kb/HT1414
2. Recovery:
http://support.apple.com/kb/HT1808

HTF do i get my iPhone to connect to network after iOS7 upgrade? (Upgrade--really?)

HTF do i get my iPhone to connect to network after iOS7 upgrade? Upgrade? Really? I'm just really upset that I have to continually make concessions to someone else and my product does NOT work the way it should, and has done in the past!!!!

Depends on your browser and it may appear in your downloads folder to run. If you are using IE, it will appear on the bottom of the screen, Google Chrome, bottom of the screen, Firefox, top of the screen with an big arrow

Cannot access usb ethernet after upgrade

I upgraded from 10.5.5 to 10.5.8 via download and now cannot access USB Ethernet. Select "Network" in System Preferences & all I get is "beach ball." When I disconnect USB Ethernet, Network appears. I had to use Apple USB Ethernet adaptor because Ethernet board got fried and did not want to buy new Mac. Can I go back to 10.5.0 then to 10.5.5 combo? If so, how?

Solved my own problem. Reinstalled 10.5 then the 10.5.5 Combo updater and now USB Ethernet works. I guess I will stay away from any further updates after this. So, my ancient eMac lives for another day.

No Network Connectivity on G4 after Tiger upgrade.

Yes, I know the machine is ancient. It's a Power Mac G4 with dual 1.25Ghz processors. Has a built in Airport card.
I did a clean install of the Mac OS the machine came with... 10.2. Airport worked fine, was able to get online.
Then, I did an upgrade to Tiger (10.4). After the upgrade ALL network connectivity is gone, cannot connect via Airport or Ethernet.
Airport card still shows up in system profiler, and the status icon is next to the time display. However, it is greyed out, and zero networks show up as being available. There are at least 5 networks available on my other Macs.
Also, Ethernet connection doesnt work either. Again, works fine when plugging the same Ethernet cable into my MacBook...works wonderfully via Ethernet. When connected directly to the Power Mac G4 however, no connectivity. No IP address at all. I've even tried doing a manual IP address, to no avail.
PLEASE HELP!!

Hi again, apply this...
The combo update for PowerPC-based Macs...
http://www.apple.com/support/downloads/macosx10411comboupdateppc.html
Does that do anything?

Cannot access iTunes store after upgrade

I recently upgraded to iTunes 10.0.4.80 and now I cannot access the iTunes store. Before the upgrade I had no issues. Any ideas?

I have just finished solving this problem after I couldnt use mine thisafternoon. 5 hrs down the line and Ive solved it! What you need to do is uninstall all the apple software :
- iTunes
- Apple software updater
- Apple Application support
- Apple mobile Device support
- Bonjour
   This actually doesn't take too much time!
   Then Shut down, reboot, and go to Apple iTunes website. Download only iTunes 10.4 and all the other software will be installed automatically while running iTunes install app.
        I tried many of the other recommended 'solutions' and none of them work. This is the only sure fire way I've found where all the software syncronises together and thus is solved.
      Hope this helps - I wish I new to just do this to start with!

Cannot access internal network after Tiger upgrade

Similar Messages

Maybe you are looking for