Cannot authenticate without one of two AD controllers

Hello, we are finally migrating our AD environment. Till migration we had one AD 2003 SP2 AD controller (physical). We have decided to add second controller(VM) based on Windows 2008 R2. Firstly, new AD controller was fully patched with MS update before
joining AD domain. 
Specs of AD controllers:
1x physical 2003 SP2 (GC, all FSMO roles), dns role
1x virtual 2008 R2(reserved 4cores, 8gb ram, 2xhdd dedicated to AD in raid 1) - GC and dns as well
Both controllers work well and replicate data between themselves. Both are GC, and 2003 holds all FMSO roles.
DNSs on DC's are configured as follows: preferred DNS - itself, secondary- second DC. 
We wanted to configure them crosswise (preferred to second DC and secondary to itself) but it gave a following, strange situation:
When only 2003 DC is online we cannot login to it with RDP and locally. Workstation login takes quite long so I assume it timesout to finally login with cached credentials. The error message is "The
specified domain either does not exist or could not be contacted"
When only 2008 DC is online we can successfully login to it with RDP and workstation login takes quite long as well. 
Unfortunatelly configuring preffered dns server to itself (local ip, not loopback) gives the same error. 
Steps that were performed:
fully patch 2003 DC
fully patch 2008 R2 
join 2008r2 to 2000 level domain served by 2003 DC
upgraded 2000 level domain to 2003
upgraded 2000 forest level to 2003
promoted 2008r2 as second GC DC
reconfigured dns as stated above.A
Above steps were performed in about one week time-span, so servers have had time to synchronize and replicate.
I would like to know what causes above situation, that without the new DC the old one doesn't serve clients nor DNS requests, so clients doesn't have internet access.
Next step is to add temporary third 2008r2 DC, migrate FSMO roles to them, demote 2003 and upgrade domain and forest to 2008 level but before that we wanted to test things and above situation occurred. 
Additionally, when the old DC starts up without the new one it logs following errors:
DNS: event 4015 - critical error, check if dns service works and is availiable,
then, six DNS: event 4004 - error, dns server was unable to enumerate following dns zones <-this one repeats for every dns zone, including _mscds.domain_name. 
I suspect dns service to fail but what's the reason? That's why server cant authenticate and serve dns requests
Any suggestions?

Hello, 
below output from 2003 dc: 
Konfiguracja IP systemu Windows
Nazwa hosta . . . . . . . . . . . : serveris
Sufiks podstawowej domeny DNS . . : domain.pl
Typ węzła . . . . . . . . . . . . : Nieznany
Routing IP włączony . . . . . . . : Tak
Serwer WINS Proxy włączony. . . . : Nie
Lista przeszukiwania sufiksów DNS : is.pl
Karta Ethernet Połączenie lokalne:
Sufiks DNS konkretnego połączenia :
Opis. . . . . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet
Adres fizyczny. . . . . . . . . . : 00-1A-64-A0-69-AE
DHCP włączone . . . . . . . . . . : Nie
Adres IP. . . . . . . . . . . . . : 192.168.0.253
Maska podsieci. . . . . . . . . . : 255.255.255.0
Brama domyślna. . . . . . . . . . : 192.168.0.254
Serwery DNS . . . . . . . . . . . : 192.168.0.253
192.168.0.252
unfortunately its Polish, but I think it's pretty clear, 
2008r2 dc(new one) below:
Konfiguracja IP systemu Windows
Nazwa hosta . . . . . . . . . . . : DC1
Sufiks podstawowej domeny DNS . . : is.pl
Typ węzła . . . . . . . . . . . . : Mieszany
Routing IP włączony . . . . . . . : Nie
Serwer WINS Proxy włączony. . . . : Nie
Lista przeszukiwania sufiksów DNS : is.pl
Karta Ethernet Połączenie lokalne:
Sufiks DNS konkretnego połączenia :
Opis. . . . . . . . . . . . . . . : Połączenie sieciowe Intel(R) PRO/1000 MT
Adres fizyczny. . . . . . . . . . : 00-0C-29-05-76-6A
DHCP włączone . . . . . . . . . . : Nie
Autokonfiguracja włączona . . . . : Tak
Adres IPv6 połączenia lokalnego . : fe80::b0b5:b4b1:4e2a:36d7%11(Preferowane)
Adres IPv4. . . . . . . . . . . . . : 192.168.0.252(Preferowane)
Maska podsieci. . . . . . . . . . : 255.255.255.0
Brama domyślna. . . . . . . . . . : 192.168.0.254
Identyfikator IAID DHCPv6 . . . . : 234884137
Identyfikator DUID klienta DHCPv6 : 00-01-00-01-1B-5A-C4-25-00-0C-29-05-76-6A
Serwery DNS . . . . . . . . . . . : 192.168.0.252
192.168.0.253
NetBIOS przez Tcpip . . . . . . . : Włączony
Karta tunelowa isatap.{E127CBD8-AE9F-4D40-9606-5E23702D527D}:
Stan nośnika . . . . . . . . . . .: Nośnik odłączony
Sufiks DNS konkretnego połączenia :
Opis. . . . . . . . . . . . . . . : Karta Microsoft ISATAP
Adres fizyczny. . . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP włączone . . . . . . . . . . : Nie
Autokonfiguracja włączona . . . . : Tak
Karta tunelowa Połączenie lokalne*:
Stan nośnika . . . . . . . . . . .: Nośnik odłączony
Sufiks DNS konkretnego połączenia :
Opis. . . . . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
Adres fizyczny. . . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP włączone . . . . . . . . . . : Nie
Autokonfiguracja włączona . . . . : Tak
Mark, the problem is with the old dc that cannot operate without the new one. 
dcdiag from old 2003:
Domain Controller Diagnosis
Performing initial setup:
Done gathering initial info.
Doing initial required tests
Testing server: Default-First-Site\SERVERIS
Starting test: Connectivity
......................... SERVERIS passed test Connectivity
Doing primary tests
Testing server: Default-First-Site\SERVERIS
Starting test: Replications
......................... SERVERIS passed test Replications
Starting test: NCSecDesc
......................... SERVERIS passed test NCSecDesc
Starting test: NetLogons
......................... SERVERIS passed test NetLogons
Starting test: Advertising
......................... SERVERIS passed test Advertising
Starting test: KnowsOfRoleHolders
......................... SERVERIS passed test KnowsOfRoleHolders
Starting test: RidManager
......................... SERVERIS passed test RidManager
Starting test: MachineAccount
......................... SERVERIS passed test MachineAccount
Starting test: Services
......................... SERVERIS passed test Services
Starting test: ObjectsReplicated
......................... SERVERIS passed test ObjectsReplicated
Starting test: frssysvol
......................... SERVERIS passed test frssysvol
Starting test: frsevent
......................... SERVERIS passed test frsevent
Starting test: kccevent
......................... SERVERIS passed test kccevent
Starting test: systemlog
......................... SERVERIS passed test systemlog
Starting test: VerifyReferences
......................... SERVERIS passed test VerifyReferences
Running partition tests on : TAPI3Directory
Starting test: CrossRefValidation
......................... TAPI3Directory passed test CrossRefValidation
Starting test: CheckSDRefDom
......................... TAPI3Directory passed test CheckSDRefDom
Running partition tests on : ForestDnsZones
Starting test: CrossRefValidation
......................... ForestDnsZones passed test CrossRefValidation
Starting test: CheckSDRefDom
......................... ForestDnsZones passed test CheckSDRefDom
Running partition tests on : DomainDnsZones
Starting test: CrossRefValidation
......................... DomainDnsZones passed test CrossRefValidation
Starting test: CheckSDRefDom
......................... DomainDnsZones passed test CheckSDRefDom
Running partition tests on : Schema
Starting test: CrossRefValidation
......................... Schema passed test CrossRefValidation
Starting test: CheckSDRefDom
......................... Schema passed test CheckSDRefDom
Running partition tests on : Configuration
Starting test: CrossRefValidation
......................... Configuration passed test CrossRefValidation
Starting test: CheckSDRefDom
......................... Configuration passed test CheckSDRefDom
Running partition tests on : is
Starting test: CrossRefValidation
......................... is passed test CrossRefValidation
Starting test: CheckSDRefDom
......................... is passed test CheckSDRefDom
Running enterprise tests on : is.pl
Starting test: Intersite
......................... is.pl passed test Intersite
Starting test: FsmoCheck
......................... is.pl passed test FsmoCheck
dcdiag from 2008r2:
Domain Controller Diagnosis
Performing initial setup:
Done gathering initial info.
Doing initial required tests
Testing server: Default-First-Site\DC1
Starting test: Connectivity
......................... DC1 passed test Connectivity
Doing primary tests
Testing server: Default-First-Site\DC1
Starting test: Replications
......................... DC1 passed test Replications
Starting test: NCSecDesc
......................... DC1 passed test NCSecDesc
Starting test: NetLogons
......................... DC1 passed test NetLogons
Starting test: Advertising
......................... DC1 passed test Advertising
Starting test: KnowsOfRoleHolders
......................... DC1 passed test KnowsOfRoleHolders
Starting test: RidManager
......................... DC1 passed test RidManager
Starting test: MachineAccount
......................... DC1 passed test MachineAccount
Starting test: Services
......................... DC1 passed test Services
Starting test: ObjectsReplicated
......................... DC1 passed test ObjectsReplicated
Starting test: frssysvol
......................... DC1 passed test frssysvol
Starting test: frsevent
......................... DC1 passed test frsevent
Starting test: kccevent
......................... DC1 passed test kccevent
Starting test: systemlog
An Error Event occured. EventID: 0x00000457
Time Generated: 07/27/2014 22:56:35
(Event String could not be retrieved)
An Error Event occured. EventID: 0x00000457
Time Generated: 07/27/2014 22:56:36
(Event String could not be retrieved)
An Error Event occured. EventID: 0x00000457
Time Generated: 07/27/2014 22:56:39
(Event String could not be retrieved)
......................... DC1 failed test systemlog
Starting test: VerifyReferences
......................... DC1 passed test VerifyReferences
Running partition tests on : ForestDnsZones
Starting test: CrossRefValidation
......................... ForestDnsZones passed test CrossRefValidation
Starting test: CheckSDRefDom
......................... ForestDnsZones passed test CheckSDRefDom
Running partition tests on : DomainDnsZones
Starting test: CrossRefValidation
......................... DomainDnsZones passed test CrossRefValidation
Starting test: CheckSDRefDom
......................... DomainDnsZones passed test CheckSDRefDom
Running partition tests on : Schema
Starting test: CrossRefValidation
......................... Schema passed test CrossRefValidation
Starting test: CheckSDRefDom
......................... Schema passed test CheckSDRefDom
Running partition tests on : Configuration
Starting test: CrossRefValidation
......................... Configuration passed test CrossRefValidation
Starting test: CheckSDRefDom
......................... Configuration passed test CheckSDRefDom
Running partition tests on : is
Starting test: CrossRefValidation
......................... is passed test CrossRefValidation
Starting test: CheckSDRefDom
......................... is passed test CheckSDRefDom
Running enterprise tests on : is.pl
Starting test: Intersite
......................... is.pl passed test Intersite
Starting test: FsmoCheck
......................... is.pl passed test FsmoCheck
Additionally, we will migrate to native 2008 level but before doing this we have make sure that everything works. 
Yes, AD,dns are configured as integrated with only one zone.

Similar Messages

  • OWA does not authenticate for one particular user

    Dear All,
    Hope you are doing great...!
    I am having Exchange 2010 Environment with NLB having two CAS servers bonded with it.
    One of OWA cannot authenticate ONLY ONE USER.  
    It just says user name or password is incorrect.
    Please suggest as early as possible.
    Regards, Jay.

    User account is not locked out, I even tried to reset the account password and tried unlocking the account too.
    User is able to access through other CAS node in NLB.
    User is not using any mobile device. He is using OWA in his desktop browser.
    Please help!!
    Regards, Jay.
    This is weird . did you try using other system ? Also what changes you have done for this user recently ?
    Amit Rawat | MCITP - Exchange 2007/2010| CCNA |MCSE- 2003| Lync 2010|http://blog.amitrawat.net

  • How to add one or two photos without synchronise my 8240 photos on my ipad2

    How to add one or two photos without synchronize my 8240 photos on my ipad2 or iPhon4 ?
    Thank you

    Just add the photos to the folders/location that you last synced and sync them - as only the contents of the last photo sync remains on the iPad, you have to (re-)sync all the photos that you want on the iPad. In theory only the new photos will need processing by the sync process, so it shouldn't take a long time to sync (it hasn't for me when I've added a few to my 1500 photos in the past anyway). Not including photos in a sync is how you remove them from the iPad.
    Your alternative is to email them to yourself and then save them from the email, but they will only go into the Saved Photos/Camera Roll album - come iOS 5 in the Autumn you should then be able to move photos between albums.

  • I CANNOT ACTIVATE ILLUSTRATOR. IT SAID I AM NOT CONNECTED TO INTERNET AND I AM. REINSTALLING ILLUSTRATOR IN ONE OF TWO BROKEN COMPUTERS. OTHER ONE IS STIL AT APPLE AND IT WILL BE BACK IN FEW DAYS. SO I WILL NEED TO REINSTALL PHOTOSHOP AND ILLUSTRATOR IN T

    I CANNOT ACTIVATE ILLUSTRATOR. IT SAID I AM NOT CONNECTED TO INTERNET AND I AM. REINSTALLING ILLUSTRATOR IN ONE OF TWO BROKEN COMPUTERS. OTHER ONE IS STIL AT APPLE AND IT WILL BE BACK IN FEW DAYS. SO I WILL NEED TO REINSTALL PHOTOSHOP AND ILLUSTRATOR IN THE OTHER ONE AS WELL.

    ammausa,
    If you have the CC, you may try to restart the Creative Cloud application by quitting and relaunching it.

  • Player Error: "You cannot record without enabling at least one track for recording"

    So I'm trying to adjust my audio using the track mixer in premiere pro cc. I assigned 2 clips to a submix. When I tried to record, I got the following error: "You cannot record without enabling at least one track for recording." I disabled other tracks, then re enabled them all, muted them all, but still got the same error when I tried to record.

    This is how I have just made a recording:
    Select track to record (1), Select record (2) then press play to record.
    Use the in-out markers in the program monitor to select the area to record.

  • I used to be able to download a lot of cd's, now I cannot download more than one or two cd's at a time. I am told that my 'cache' is full and I need to re-start iTunes to clear some of the 'cache' memory. What is the cache and how do I resolve this?

    CD download problems:
    I used to be able to download numerous cd's at a time but now I can only do one or two until I restart iTunes. I have been told that my 'cache' is full and will only empty a little a each restart. I did look at the properties and the 'cache' is showing full How do I correct or improve
    this?

    Final Cut is a separate, higher end video editor.  The pro version of iMovie.
    Give iPhoto a look at for creating the slideshow.  It's easy to assemble the photos in an album in iPhoto, put them in the order you want and then make a slideshow of them.  You can select from various themes and transitions between slides and add music from your iTunes library.
    When you have the slidshow as you want use the Export button at the bottom of the iPhoto window and export with Size = Medium or Large.
    Save the resulting Quicktime movie file in your Movies folder.
    Next, open iDVD, choose your theme and drag the QT movie file into the menu window being careful to avoid any drop zones.
    Then follow this workflow to help assure the best qualty video DVD:
    Once you have the project as you want it save it as a disk image via the File ➙ Save as Disk Image  menu option. This will separate the encoding process from the burn process. 
    To check the encoding mount the disk image, launch DVD Player and play it.  If it plays OK with DVD Player the encoding is good.
    Then burn to disk with Disk Utility or Toast at the slowest speed available (2x-4x) to assure the best burn quality.  Always use top quality media:  Verbatim, Maxell or Taiyo Yuden DVD-R are the most recommended in these forums.
    The reason I suggest iPhoto is that I find it much easier to use than iMovie (except for the older iMovie 6 HD version).  Personal preferences showing here.

  • Cannot download itune music purchases  -  email account before adding new account email now cannot get without paying again-- what to do???

    Fdsfi deleted my email account that I had used to purchase music.  I forgot to tell iTunes that I was changing emails so I lost all music that I had purchased.  Now I cannot get without purchasing again.   Is their anything I can do about this short of paying again ????
    Fyellis000@

    This is bad - I have an Apple automated response that they got my report on 12/6, 12/10 and 12/14, and I haven't heard anything from them since the 6th when I got one reply that told me to do things I tried before reporting the problem. Between the 6th and 10th I replied to their response 4 times and they ignored me, forcing me to report a problem with two more items that wont download but getting no response.
    How do they get away with this kind of behavior, especially for someone with FIVE Core 2 Duo macs and thousands of dollars of of iTunes store purchases? I'm getting really ******.

  • One sender - two receivers - same Message-ID?

    Hi,
    I don´t know if it is possible to send a message (which is, as you know identified by its Message-ID) to two receivers where at least one receiver has to keep the Message-ID of the xi-incoming message. This is necessary because it has to be used as part of the receiver-filename.
    We work with triggerfiles, which identify in which sequence the Messages have to be processed at the receiver system. If you use more than one interface determination, for each receiver an new Message-ID is generated. This is what I want to prevent.
    Does anyone know if this is possible using a business process. (XI3.0 SP17)
    If yes, what is it to look like? I´m thinking about one receiver and two senders (in bp-design) :).
    Regards,
    Thomas

    Hi VJ,
    I think your doubts are reasonable, as this doesn´t fit the "Exactly once"-idea of messages. As soon as the bpe picks up the Message, you got no chance to save the original Message-ID. I just designed a little process to give it a try, but it didn´t work (i. e. the two new Message-IDs appeared for the BP-outgoing messages).
    Why I want to use it? This would be an addon for a more or less complex Szenario, which we cannot change without a redesign of the hole szenario ...
    I think we´ll have to let the application server generate the Message twice with different receiver agreements. Sounds ugly.
    Thank you for confirmation.
    Best regards
    Thomas
    Best regards
    Thomas

  • Users cannot authenticate

    Hello
    I recently had a lot of errors on two ML servers actinbg as OD Master/Replica, so decided to reinstall from scratch. One is running OS X 10.8.2, the other 10.8. Both are vanilla installs (going so far as to recreate the RAID), and both have the latest version of server.app installed.
    Network users cannot authenticate.
    Running slapconfig -ver gives the following errors on both machines:
    bubbles:~ administrator$ sudo slapconfig -ver
    2012-11-27 20:17:31 +0000 command: /usr/libexec/slapd -T cat -c -f /etc/openldap/slapd.conf -s ou=macosxodconfig,cn=config,dc=test249,dc=home
    2012-11-27 20:17:31 +0000 Error execing slapcat: 50b51fdb /etc/openldap/slapd_macosxserver.conf: line 303: unknown directive <TLSCertificatePassphrase> inside backend database definition.
              slapcat: bad configuration file!
    LDAP Setup Tool (slapconfig), Apple, Inc.,  Version 1.2
    Obviously ou=macosxodconfig,cn=config,dc=test249,dc=home is wrong, but I don't know where this setting is held to correct it to ou=macosxodconfig,cn=config,dc=server,dc=domain,dc=tld
    Opeining slapd_macosxserver.conf shows the last four lines to be:
    TLSCertificateFile      /etc/certificates/server.mydomain.LONGHASH.cert.pem
    TLSCACertificateFile    /etc/certificates/server.mydomain.LONGHASH.chain.pem
    TLSCertificateKeyFile   /etc/certificates/server.mydomain.LONGHASH.key.pem
    TLSCertificatePassphrase        "Mac OS X Server certificate management.LONGHASH"
    I can 'fix' the second error by commenting out that last line. But that just results in a new and exciting error:
    bubbles:~ administrator$ sudo slapconfig -ver
    2012-11-27 20:43:00 +0000 command: /usr/libexec/slapd -T cat -c -f /etc/openldap/slapd.conf -s ou=macosxodconfig,cn=config,dc=test249,dc=home
    2012-11-27 20:43:00 +0000 Error execing slapcat: slapcat: slap_init no backend for "ou=macosxodconfig,cn=config,dc=test249,dc=home"
    LDAP Setup Tool (slapconfig), Apple, Inc.,  Version 1.2

    Hi
    i get the same error but authentication still works.
    Are you sure that the recovery of your password worked ?
    In case I have this issue i can only authenticate as a local user, not as an opeddir user.
    This user must have admin rights to make sudo, afaik.
    But it is interesting that my error comes on line 302 and yours on line 303.
    Below i have attache the auth part from my /etc/openldap/slapd_macosxserver.conf
    Check for any difference.
    macmini:~] user% sudo slaptest -f /private/etc/openldap/slapd.conf -v
    Password:
    52054639 /etc/openldap/slapd_macosxserver.conf: line 302: unknown directive <TLSCertificatePassphrase> inside backend database definition.
    slaptest: bad configuration file!
    # authdata database definitions
    database        bdb
    suffix          "cn=authdata"
    rootdn          "uid=root,cn=users,dc=macmini,dc=domain,dc=TL"
    directory       "/var/db/openldap/authdata"
    checkpoint      128 1
    index           default eq
    index           objectClass eq
    index           authGUID eq
    index           entryUUID eq
    index           entryCSN eq
    index           draft-krbPrincipalAliases eq
    index           draft-krbPrincipalName eq
    timelimit 60
    idletimeout 300
    cachesize       20000
    idlcachesize    10000
    sizelimit size.pr=11000 size.prtotal=unlimited
    #limits          set="computer/cn & [cn=com.apple.opendirectory.group,cn=computer_groups,dc=macmini,dc=domain,dc=TL ]/memberUid" time.soft=unlimited time.hard=unlimited size.soft=unlimited size.hard=unlimited
    access to *
                    by dn.exact="uid=_ldap_replicator,cn=users,dc=macmini,dc=domain,dc=TL" write
                    by sockurl="ldapi://%2Fvar%2Frun%2Fldapi" write
    TLSCertificateFile      /etc/certificates/macmini.D5473ED3099C09ACE59C2944EA9FDDFC024DC07.cert.pem
    TLSCertificateKeyFile   /etc/certificates/macmini.D5473ED3099C09ACE59C2944EA9FDDFC024DC07.key.pem
    TLSCertificatePassphrase        "Mac OS X Server certificate management.D5473ED3099C09ACE59C2944EA9FDDFC024DC07"
    TLSCACertificateFile    /etc/certificates/macmini.D5473ED3099C09ACE59C2944EA9FDDFC024DC07.chain.pem

  • Want to go, it either does not nd I cannot correct the one letter.

    New to iPad. How do you move the cursor back without erasing everything you've typed? When I tap on the place I want to go, It either does not move, or the word highlights in pink and I cannot correct the one letter? I also cannot get the first letter in a case-sensitive situation to come up as lower case, even using the arrow key. Thanks for your help!

    If you press and hold the screen then after a second or two you should get a magnifying glass which should allow you to position the insertion point more accurately - you can then re-position it back to the end of your text by the same method. You should be able to change the case by pressing the shift/up arrow key and then typing the letter; if you go back and delete an upper case letter then the letter that you type in its place will be in upper case unless you press the shift/up arrow button before you type it i.e. the case will default to the last deleted character.

  • Cannot authenticate the phone

    Version 6.86.9.3 of Nokia PC Suite fails with error message:
    "Cannot authenticate the phone"
    It does not matter what I try (rebooting unpairing/repairing, etc.) it does not work.
    The previous version of the software worked fine.
    My setup:
    Phone: Nokia 6233
    Windows 2000 Server
    BlueSoleil Bluetooth USB key.
    BlueSoleil 2.3.0.1 Release 060802
    Stack Version: 05.04.11.20060622
    I downloaded a very large update from Nokia, and upgraded for a better experience, however it resulted in a worse experience. I feel very bitter about upgrading.
    Do Nokia even monitor these message boards? I've seen others with similar problems but with no solid answers from Nokia other than, "are you sure you plugged it in and paired it properly".

    Yes, I have tried your suggestion and it did not work.
    I have checked permissions using a sysinternals tools. There are no permission problems, although the following two files were modified during the failed connection attempt.
    C:\Documents and Settings\All Users.WINNT\Application Data\PC Suite\ConfServer\Settings.xml
    C:\Documents and Settings\All Users.WINNT\Application Data\PC Suite\ConfServer\Nokia;SuiteConf;RM-145;359727000098587.xml
    I am curious to see how long it takes Nokia to resolve this error I am getting. I know I'm not the only one... and I'm not going away until it is fixed.

  • I apparently have more than one Apple ID.  So, 1) how do I find out how many different ones exist, and 2) how can I consolidate them into one or two?

    I have inadvertenly created two or more different Apple IDs.  How can I learn all the different IDs associated with my email accounts or my name?  How can I consolidate the different IDs into one or two?

    Go to https://iforgot.apple.com/ and click the blue link "Forgot your Apple ID?"
    It will result a page in which you can provide some contact information that may possibly find an existing Apple ID.
    How can I consolidate the different IDs into one or two?
    This cannot be accomplished.

  • Issue Printing One or Two Checks on HP LaserJet Pro 200 MFP M276nw

    I just purchased an HP LaserJet Pro 200 MFP M276nw which replaces an HP Color LaserJet 2605dn.
    I've run into an issue printing checkes from Quicken when I print less than a full sheet (one or two) checks.
    With my old printer, I used the manual feed for a partial sheet.
    Since the new printer does not have a manual feed, I have to put the partial sheet in the paper tray.
    It seems one of two things happen:
    1) Sometimes the printer will print the partial page but then displays an error message which says something like "Unexpected paper size, load letter."
    It then re-prints the partial page on the next sheet of paper.
    2) Othertimes, it prints the partial page without the error message, but then feeds the next sheet of paper throught the printer.
    In either case the next page contains the next three checks, so it's either wasting checks or printing on the wrong check numbers.
    Any suggestions on how to avoid these issues would be appreciated.

    Me too.
    I've been using an alternate printer for printing the checks, but I'd rather get rid of the old one. (The HP Laser Pro 200 takes up a lot of space!)
    KC, Seems like you've been waiting for an answer for a VERY long time.  I'm not going to hold my breath.
    Hey HP!  Do you ever monitor this site?!
    KC-Texas wrote:
    I just purchased an HP LaserJet Pro 200 MFP M276nw which replaces an HP Color LaserJet 2605dn.
    I've run into an issue printing checkes from Quicken when I print less than a full sheet (one or two) checks.
    With my old printer, I used the manual feed for a partial sheet.
    Since the new printer does not have a manual feed, I have to put the partial sheet in the paper tray.
    It seems one of two things happen:
    1) Sometimes the printer will print the partial page but then displays an error message which says something like "Unexpected paper size, load letter."
    It then re-prints the partial page on the next sheet of paper.
    2) Othertimes, it prints the partial page without the error message, but then feeds the next sheet of paper throught the printer.
    In either case the next page contains the next three checks, so it's either wasting checks or printing on the wrong check numbers.
    Any suggestions on how to avoid these issues would be appreciated.

  • AS/400 to Two 5494 controllers using STUN

    Hello,
    I've configured STUN between an AS/400 and 2 x 5494 controllers across a serial link using two 2621 routers
    I've pretty much copied the configuration from the example web site which shows this exactly as we have it
    http://www.cisco.com/en/US/partner/tech/tk827/tk369/technologies_tech_note09186a00800b451e.shtml
    The IBM engineer is saying the RTS lines never drop so he is not able to activate either controller.
    Can you give the config a quick look and possibly tell me where I'm going wrong please
    Many thanks
    Tony
    hostname Site_A
    stun peer-name 172.16.1.1
    stun protocol-group 1 sdlc
    stun remote-peer-keepalive 10
    interface Loopback0
    ip address 172.16.1.1 255.255.255.0
    interface Serial0/0
    description *** Kink to Site B ***
    bandwidth 960000
    ip address 192.168.200.2 255.255.255.252
    priority-group 1
    interface Serial0/1
    description *** Link to AS/400 ***
    no ip address
    encapsulation stun
    idle-character marks
    nrzi-encoding
    clockrate 19200
    stun group 1
    stun sdlc-role secondary
    sdlc K 1
    sdlc address 01
    sdlc address 02
    stun route address 1 tcp 172.16.2.1 local-ack
    stun route address 2 tcp 172.16.2.1 local-ack
    ip route 0.0.0.0 0.0.0.0 192.168.0.1
    priority-list 1 protocol stun high
    priority-list 1 protocol ip medium tcp 1990
    priority-list 1 protocol ip normal tcp 1991
    priority-list 1 protocol ip low tcp 1992
    priority-list 1 protocol stun high address 1 1
    priority-list 1 protocol stun high address 1 2
    hostname Site_B
    stun peer-name 172.16.2.1
    stun protocol-group 1 sdlc
    stun remote-peer-keepalive 10
    interface Loopback0
    ip address 172.16.2.1 255.255.255.0
    interface Serial0/0
    description *** Serial Link to Site A ***
    bandwidth 960000
    ip address 192.168.200.1 255.255.255.252
    no ip route-cache
    no ip mroute-cache
    priority-group 1
    interface Serial0/1
    description Serial Link to 5494 Controller 01
    no ip address
    encapsulation stun
    no ip route-cache
    no ip mroute-cache
    nrzi-encoding
    clockrate 19200
    stun group 1
    stun sdlc-role primary
    sdlc address 01
    stun route address 1 tcp 172.16.1.1
    interface Serial0/2
    description Serial Link to 5494 Controller 02
    no ip address
    encapsulation stun
    no ip route-cache
    no ip mroute-cache
    nrzi-encoding
    clockrate 19200
    stun group 1
    stun sdlc-role primary
    sdlc address 02
    stun route address 2 tcp 172.16.1.1
    ip route 0.0.0.0 0.0.0.0 192.168.200.2
    priority-list 1 protocol stun high address 1 1
    priority-list 1 protocol stun high address 1 2

    Hi Tony,
    The first thing is that this line has clock rate configured, which must mean it is DCE ( has a DCE cable attached ). This means RTS comes from the AS/400 and not the router. CTS would come from the router. If you want this to work as half duplex, add half-duplex to the serial interface configuration. Also, you should add the global command, "stun quick-response" on the AS/400 side router only. Local-ack is by STUN group, all of none. "Stun quick-response" is only valid with local-ack. It prevents the AS/400 from taking the line down if one of the remote controllers is down. This allows the other to stay up. The router will respond with DM for the controller that is down.
    Best regards,
    Jim

  • Creating one and two Dimensional array

    Hi guys my problem is as follows
    (1)I want to create a two dimensional array of 10 rows and 20 columns
    (2)Populate the array with random integers
    (3)convert the two dimensinal array into one dimensional array int[]nums
    (4)print the content of one and two dimensional arrays to the screen

    You don't learn much about coding if you don't write any code. Without seeing the code that was written it's very difficult to assist a person, since your solution may not be anywhere close to their solution. If the poster just wants the code to hand in or use as is then there is no learning happening.
    So, step 1 - post your code, step 1a - ask a clear question.
    Just my opinions
    Lee

Maybe you are looking for

  • Raise Form_Trigger_Failure Problem..?!

    Hello All.. i have a problem indicates that most of raise validation doesn't work..Does anyone knew some suggested reasons for that strange case..pls? Regards, Abdetu..

  • Super fast wifi at times on original iPad

    Was wondering if anyone else has experienced this on their original iPad. So I own a 3G / wifi 32 original iPad ... Bought in 2010.    It works great, iOS 5.1.1 I've noticed that at certain times, especially at night, between 6-midnight and slightly

  • Org unit relations not created

    Hi Experts, We are facing one issue. When there is large change in HR data then 3-4 IDOC came into SRM system. Generaly first IDOC carry new org unit information abd second IDOC carry relation of Org unit with higher org unit. As IDOC processes simul

  • Can anyone offer help using CS4 as external editor for iPhoto '08?

    I am very new to CS4 Extended, having upgraded from Elements 6 recently.  I use iPhoto '08 to do all my photo organization and really enjoy it, have a LOT of work invested in it and don't really want to switch to anything else if I can help it.  One

  • Error in Insertion through procedures

    Dear all, I executed below procedure without error, but the rows are not inserted in the table........... create or replace procedure pq_demo is cursor cr_rad is select * from rad where radius<10; cr_val cr_rad%rowtype; area number; begin open cr_rad