Cannot connect to com1 using Switch Executive

I have a PXI2530 configured using Switch Executive 2.10. The first 60 Channels are setup with my signal names on ch0 - ch59. Com0, 1, 2 and 3 are my Instrument connections. The IVI Driver Sessions has Driver Setup set to Topology:2530/1-Wire Octal 16x1 Mux.
When I try to configure either a Channel, Route or a Group, there is only a com0 pin and no com1, 2, 3, 4, 5, 6 or 7. There is no way to connect to any pin beyond ch15.
The configuration looks like it is setup for a 128:1 mux, but when I try to connect ch16 to com0, it cannot complete the route. Ch16 cannot be connected to com0 or any channel in the list. Any idea what I am doing wrong?
Michael Munroe, ABCDEF
Certified LabVIEW Developer, MCP
Find and fix bad VI Properties with Property Inspector

Michael,
What probably happened is that originally the NISE vd was created using the 128x1 topology. If the driver session is changed to another topology (like Octal 16x1 Mux) and saved the linked from the NISE vd and the old topology still exists until you close MAX and reopen it. When MAx opens it establishes a link between the NISE vd and driver session which remains in memory until MAX is closed and reopened.
Guy Ferraro
Switch Product Support Engineer
NI - USA

Similar Messages

Cannot connect to com1 in PXI2530 using Switch Executive

I have a PXI2530 configured using Switch Executive 2.10. The first 60 Channels are setup with my signal names on ch0 - ch59. Com0, 1, 2 and 3 are my Instrument connections. The IVI Driver Sessions has Driver Setup set to Topology:2530/1-Wire Octal 16x1 Mux.
When I try to configure either a Channel, Route or a Group, there is only a com0 pin and no com1, 2, 3, 4, 5, 6 or 7. There is no way to connect to any pin beyond ch15.
The configuration looks like it is setup for a 128:1 mux, but when I try to connect ch16 to com0, it cannot complete the route. Ch16 cannot be connected to com0 or any channel in the list. Any idea what I am doing wrong?
Michael Munroe, ABCDEF
Certified LabVIEW Developer, MCP
Find and fix bad VI Properties with Property Inspector

http://forums.ni.com/ni/board/message?board.id=320&message.id=633
Duplicate threadMessage Edited by Berto on 02-28-2006 12:15 PM

Cannot connect to server using message server: ms://xiidhasoft:50004/P4

Hi SAP Guru's
When PISUPER or any any of the enduser is trying to login in the Integration Builder , they are getting error
Cannot connect to server using message server: ms://xiidhasoft:50004/P4
I have tryed to search in SDN and got below solution but no success
1. Exchange Profile of PI - http://host:port/exchangeProfile
2. Check with the rmi port number.
3. if rmi port number is empty or any number is present ( check with Tr code: SMICM - services - check for p4 port number - it will be ex: 5<nr>04)
4. fill the rmi port number as present in the P4.
OR
implement note 864268
I have Netweaver PI 7.1 .
Please suggest some alternative solution.
Thanks & Regards
Vinay Patel

You may check your local PC Java Network Setting.
Troubleshooting:
Probably Javau2122 WebStart does not detect the correct Proxy Settings. In this case please proceed as follows:
To change the Proxy Settings for Javau2122 Web Start:
1. Click Start --> Run and enter javaws. Press button OK.
2. Control Panel -> Programs ->Java -> Network Settings...
3. Select Direct Connection to switch off the proxy settings and press button OK.
If this still does not work, select Use proxy server to set manually the HTTP Proxy and Port.
Contact your network administrator for the correct settings.

PI 7.11: Cannot connect to server using message server:...

Hello Guys,
we make the Application Management for a Customer PI System.
Scenario:
- the SAP Gui Connection to the ABAP Stack is routed via SAPRouter and Works fine.
SAP Gui -> our SAP Router -> VPN Box from Customer -> Firewall Customer -> ABAP Stack PI System
- WebAccess its working fine, the Customer use Webdispatcher on every PI Server...
Browser -> VPN Box from Customer -> Firewall Customer -> Java Stack (Port: 5xx00 btw. 81xx (Webdispatcher))
Problem:
Our Problem ist, we can not proceed the Integration Builder or the ESB, the Java Web Start works fine and open the Logon Screen Correctly -> but i fill the Logon Screen with my User name and Password and press Logon come the follwing Error:
"Cannot connect to server using message server: ms://<hostname>.<domain>:8134/P4"
In the Details from the Error Message:
"<hostname>.<domain>:53404 Reason: com.sap.engine.services.rmi_p4.P4IOException:
Cannot open connection to host: <IP-Adress of Central Instance> and Port: 53404"
The Customer says, the Firewall is open with the IP Adresses and P4 Port but i dont think so...
Can everybody help me, or have tips for me! I have checked a lot of OSS Messages (PI High Availabilty etc... its all correct on the System)
Sorry for my bad English
Best Regards,
Markus

Hi Markus,
did you check if the browser is using a proxy? (In this case your scenario unfortunately won't work).
P4-port should generally be routed via a proxy (described in the help.sap.com), but within the PI-Tools(JNLP) the proxy-usage is not implemented. There is even a SAP-note that describes how to check the JavaWebStart-Proxyconfiguration, but this won't help either.
If there is a proxy defined in the browser everything is working fine till you pass the logon-screen but even with the correct "javaws"-settings you won't be able to go on.
(This problem is pretty bad if you do have developers and the SAP-servers seperated because of security issues. I'm hoping that this malfunction will be solved with upcoming patches.)
Solution: Establish a connection without any proxy in between.
E.g.: a terminal server in the same network
It would be helpful to find more people with the same problem to force a fix from SAP for that.
If anyone else is having problems with this, please add a comment to this thread.
Best regards
Christian

The transaction associated with the current connection has completed but has not been disposed. The transaction must be disposed before the connection can be used to execute SQL statements.

Hello All,
I am getting below error can you please help me
Error:-
The transaction associated with the current connection has completed but has not been disposed. The transaction must be disposed before the connection can be used to execute SQL statements.

Perhaps this thread will help you out
http://stackoverflow.com/questions/11453066/error-the-transaction-associated-with-the-current-connection-has-completed-but
Best Regards,Uri Dimant SQL Server MVP,
http://sqlblog.com/blogs/uri_dimant/
MS SQL optimization: MS SQL Development and Optimization
MS SQL Consulting:
Large scale of database and data cleansing
Remote DBA Services:
Improves MS SQL Database Performance
SQL Server Integration Services:
Business Intelligence

Scan list using Switch Executive

I have a number of signal routes using multiple switch cards that I have set up using switch executive. I want to create a scan list that will switch each of my routes in turn each time I see a hardware trigger on the trigger inputs of my switches.
I have looked at some examples in TestStand and can see that if I use the IVI Switch Step using the IVI Switching setting that I can set up a scan list but that seems to be only for one switch card, I have two that I need to route signals to a Digitizer. I can not see a way of using my routes set up using Switch Executive.
I can either use LabView2013 or TestStand 2013 to do this.
Some help would be most appreciated?
Wayne

Hi Wayne,
If I have understood your problem correctly, this VI in LabVIEW sound like it does what you are after.
NI Switch Route Trigger Input
Also at the bottom of this LINK are some examples of scan lists, perhaps you will be able to adapt this to your needs
Please let me know how you get on
Kevin R
Applications Engineer
National Instruments UK&Ireland

Since a I have intalled OS X Lion I cannot connect internet mobile using my ZTE mobile pen

Since a I have intalled OS X Lion I cannot connect internet mobile using my ZTE mobile pen.

It sounds like you need updated drivers. They are hard to find for that thing. This is what I found on a cursory search:
http://studiofourfour.zendesk.com/entries/20305042-mac-os-x-lion-3-zte-usb-broad band-drivers
You should consider contacting the manufacturer or cell provider that sold you the modem for support.

How do I associate switches in a four layer relay tree using Switch Executive

I have a three layer relay tree, controlled with a PXI-2567, to route an instrument input to 16 DUT channels. How do I create aliases in Switch Executive to turn the appropriate set of three relays on and off to route the input signal to one of the channels?

Bob,
Here is what you need to do to be able to call 2 end channels and create a route though 3 layers.
1) You have to tell NISE how the independent relays are connected to each other. You will do that by creating Hardwires.
2) You need to tell NISE that you want the channels connected to the hardwires to be used for routing. You will do that by marking the connected channels as "Reserved for Routing".
3) You can name the end channels according to your topology. COM for the single input channel and CH0 to CH15 for the output channels by creating aliases.
In the route editor, you will only need to create a route between COM and CHx and NISE will find the appropriate relays to close. In the route editor, if you only want to see the channels with an alias (COM, CH0, CH1 etc...) select in Options "Hide channels without aliases"

Cannot connect to database using the Upgrade Simulation Tool

I have installed the Upgrade Simulation Tool on my system and when I try to run the tool my system works in the for awhile in the background and creates the _Simulation mdf and ldf files and a .bck file. After 3 or 4 minutes it gives me an error "Cannot connect to the database".
It looks to me like it is connecting to the database because it is creating the files in the SQL Data folder. I have tried to run it on several databases and get the same results.
Thank you, Jeff

Hi,
You may not have the ability to upgrade it directly.
He does have the ability.
When downloading Pl 42, it is cleary marked as "Upgrader", which means it can be used for upgrade (in this case simulation) from a lower version than 2007A
Patchlevel which are marked as "patch" are suitable only for updating the PL within the very same version of SAP Business One.
This tool should run under 2007 system I believe.
The Upgrade Simulation tool was designed in orderto test an upgrade, therefore it can run at a machine where 2005 version is installed. Technically speaking it creates a second SBO-common, which can be used only with the special designed (read only) client of the tool.
Jeff, you should check access rights of your SQL Data folder.Maybe grant user "Everyone" modifying rights to that folder. In addition you could try to detach a DB and move the related *.mdf and *.ldf to another folder where no access denied rights were applied.
If using MSSQL 2005 create via ODBC a Native Client connection to the Server, although you might just working locally only.
Regards
Mario

Cannot connect to database using SQL*Plus

Hi, I have Oracle 10g XE installed in my labtop and I cannot connect using SQL*Plus.
I can connect using the broser User Interface though, which I was able to do after doing the following procedure to change the password of the sys account:
-     open a command prompt
-     - type sqlplus
-     On the “Enter user-name” line, type /as sysdba
-     On the SQL> prompt, type alter user sys identified by NewPassword;
But the thing is that even though I am able to connect using sys/NewPassword from my browser UI, I dont get the same result when doing it using the SQL prompt.
What I am trying to do is this:
SQL> connect sys/NewPassword
Then I get first a warming saying that I need to use either sysdba or sysoper to connect to the system account, but neither of those work.
Can anyone advice me on this matter?
Thanks in advance

Thanks for that.
I run the command to list the usernames on the database and I got SYS and SYSTEM in the list. But again, when I try to use SYS with a password that I know is working because I can access it through the browser UI, it doesnt work. It seems like this sys is different to the sys I used in the UI.
I dont know if I am explaining myself correclty... In the Browser UI I use sys, and a password and I get connected to the sys account. However, if I try to use the same sys.password combination from my sqlplus prompt, I get error messages
Does this make sense at all?

Cannot connect to internet using apple applications

Hi,
I cannot connect to the internet using these apple applications: Safari, Software Update, iTunes.
I can connect to the internet using Firefox and iChat.
I have just reinserted my OSX 10.4 discs and reinstalled the software (making an archive and using my old settings choice). But it still doesn't work.
Why won't apple applications connect to the internet?

Lisa W wrote:
I just updated to 10.4.11 and tried to run my brand new Safari 3. NO GO.
I'm having a much smaller problem (just accessing certain sites) which I think may have begun with 10.4.11. I'd agree that you might want to try launching the disk utility and repairing permissions. Then you may want to run Software Update again and see if it finds other updates that may be required. Sometimes after a revision patch application, especially if you don't apply patches soon after their release, there are other applications and stuff which need to be updated after you've run the initial update. It's not a typical thing, but it does happen on occasion.
The only time I've really had a problem with an update was, I believe, 10.4.9... I think I let Software Update do it's job, but wasn't ready to save and quit an open document or two, so just did something I'd done before, without issue... I "force-quit" Software Update. This was not an advisable move, as it turned out. Indeed, I think that time, after staying up all night trying to suss out the problem, was when I found a couple other people who'd had similar issues with the update because it required a second re-start after patch application. In my sleep-deprivation-induced state of temporary insanity I selected a user name which I now find rather embarrassing... I don't remember picking "MacCrackHead", actually... LOL ... but that's another story.
If you have an external drive that you've backed up your system install to, you may be able to boot off of it and see if things work normally (as I did when I moved from 10.4.8 to 10.4.9 and had the issues)... Ultimately I ended up making a second back-up of my external back-up and running the 10.4.9 update offline. It went well, so I cloned my back-up back to my normal start-up. I can't remember now what the issue was then, but it was pretty problematic for me.
My routine, when I see an important update available is now:
1) Don't update when Software Update finds something;
2) Save my work and close all applications.
3) (Recommended): Bring my back-up clone of my start-up drive up-to-date.
4) Run software update.
5) Restart when it tells me to (required for many updates, and all system version updates)
6) Run software update again on re-boot to see if there's anything else that follows... (usually none)
7) Run disk utility and repair permissions.
Good luck resolving your issue, Lisa.
Lowell

Cannot connect to Internet (using Safari)

Hi all.
I got my Macbook (unibody) for about 7 months ago. I have never had any problems with it, but now suddently Internet has stopped working. I am using only Safari. It just says "cannot connect to Internet" when i try get online. The weird thing is that Internet works to all other computers here at home, but not on mine. I have checked that all the cords are plugged in and all lights are on. I have tried using the internet cords for the other computers on my Mac, but they dont work. The cord i am using is working on other computers too, so there is nothing wrong with it. It is like my Mac doesn´t "recognize" that i have the cord plugged in. When i am on the systems settigns it says that everything is offline, and when i am on the Ethernet settings it does not have any IP adress written or anything, and i have chosen "Use DHCP".
What should i do? I was watching a movie yesterday and had the laptop in my lap, maybe it got overheated or something? Or is it something wrong with the network card? Please help, this is so frustrating!

Hi all.
I got my Macbook (unibody) for about 7 months ago. I have never had any problems with it, but now suddently Internet has stopped working. I am using only Safari. It just says "cannot connect to Internet" when i try get online. The weird thing is that Internet works to all other computers here at home, but not on mine. I have checked that all the cords are plugged in and all lights are on. I have tried using the internet cords for the other computers on my Mac, but they dont work. The cord i am using is working on other computers too, so there is nothing wrong with it. It is like my Mac doesn´t "recognize" that i have the cord plugged in. When i am on the systems settigns it says that everything is offline, and when i am on the Ethernet settings it does not have any IP adress written or anything, and i have chosen "Use DHCP".
What should i do? I was watching a movie yesterday and had the laptop in my lap, maybe it got overheated or something? Or is it something wrong with the network card? Please help, this is so frustrating!

AMD CPU with Vista cannot connect to WLAN using MS-PEAP with WEP-128

We have a notebook "HP Pavilion tx1000 (AMD Turion64 CPU with Vista 32bits)". The notebook is using Broadcom 802.11a/b/g chipset, running AMD and Vista. It cannot associate to WLAN using MS-PEAP and WEP-128. Also, it cannot associate to PEAP and WPA2-AES.
The AP's log shows:
Oct 11 15:35:20 CCT: %DOT11-7-AUTH_FAILED: Station xxxx.xxx.xxxx Authentication failed
The ACS's log shows:
"EAP-TLS or PEAP authentication failed during SSL handshake"
We do not validate the certificate in the wireless setup. Vista's WLAN AutoConfig is used to configure the wireless profile. We are running Autonomous AP with Switch-Based WDS (WLSM).
We have no issue with Intel Centrino on the above authentication and encryption scheme.
Have checked the CCX program, broadcom 802.11a/b/g chipset is supported only for windows 2000 and xp. There is no mentioning about support for vista. Could this be a compatibility issue?
Please advise and thks

Maybe look at this post: http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=WLAN%20Radio%20Standards&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddf9be9/5#selected_message

Cannot connect to receiver using AirPort Extreme due to password protection

I have a new AirPort Extreme and Harman Kardon receiver. I am trying to connect the HK receiver to my home network, after entering in all the necessary info (IP, subnet mask etc) I still cannot connect to internet radio, Pandora etc. I called HK and they say it is because my home network is password protected. They recommend I disable to the password and keep it without a password. Is this the only option I have?

There is no reason to do this if your HK receiver cannot connect using wireless, as appears to be the case here. You must have misunderstood the HK support person, or they misunderstood you when you spoke with them.
The information in the manual only talks about a wired Ethernet connection. There is no information that I can find that would indicate that the HK Receiver will be able to connect to the wireless network using wireless.
Unless you can provide another link that would indicate otherwise, you will need to plan to connect the HK receiver using a wired Ethernet cable, or use a pair of EOP adapters to send the signal over the AC wiring in your home.
It would also be possible to use an AirPort Express to connect to the AirPort Extreme over wireless by locating the AirPort Express near the HK receiver and then in turn connecting a short Ethernet cable from the AirPort Express to the HK receiver.

Cannot connect to itunes using 3g

I can connect to itunes or apps using wifi but i cannot connect using 3g....is this usual ....I'm using vodaphone in the uk

Can you connect to anything with 3G via the internet? Do you see an cellular icon and bars on the upper right? Is cellular turned on? In setting what odes it say under your cellular account under cellular data?

Cannot connect to com1 using Switch Executive

Similar Messages

Maybe you are looking for