Cannot establish TLS with SMTP...wrong address, connection error 5

An error occurred sending mail: The mail server sent an incorrect greeting: Cannot establish TLS with SMTP server 65.55.176.126:587, SSL_connect error 5:connection closed.

Is this for an Outlook/Hotmail type account? What do you have for the server settings under Tools/Account Settings/Outgoing Server (SMTP)? (For outlook/hotmail it should be STARTTLS security on port 587, normal password authentication, email address for the User name.)
If you have an anti-virus/security program scanning outgoing mail, disable that option and see if it helps.

Similar Messages

When sending email I get this error message: An error occurred sending mail: The mail server sent an incorrect greeting: Cannot establish SSL with SMTP server

This issue has popped up before then went away after I switched to SSL setings as suggested by my website host. Or...was it pure coincidence? Same problem today and I haven't made any changes since the above mentioned and have had many successful emails sent. Can't reply or send emails and the draft gets removed from the draft folder even if I saved it before hitting send. Thank you!

Thank you Matt. I'm sure this will be frustrating ...but the more I think about this problem there more info I have to share. The emails I write that do not get sent do end up in my "sent" folder but never reach the recipient. And, most perplexing, the issue/problem is sporadic. It was coming and going before I switched over to the SSL/TLS option in T-bird. And...since the switch it has reappeared and disappeared. I have made zero changes other than the above mentioned. I did get a security update today for T-bird perhaps this will help?
I read your link, thank you.
I obviously don't understand how these systems work. I'm baffled how an issue like this can come and go...

Message cannot be transferred to node SMTP due to connection error (final)

HI Gurus,
we are gewtting the following error inour test client in SOST transaction. Can someboyd please thriw soem light on how to resolve this?
Message cannot be transferred to node SMTP due to connection error (final)
Message no. XS816
Diagnosis
Due to a technical fault, the system could not set up a connection to the RFC destination Check port and mail server for SMTP nodes. Therefore, the message could not be transferred to node SMTP.
System Response
The system was unable to transfer the message.
Additional information of the node used (in the system language of the node):
Procedure
Check the connection from SAP system to node SMTP. Perhaps the node is not assigned to the correct RFC destination. If so, correct this in Customizing.
Otherwise use RFC destination management to check the RFC connection to destination Check port and mail server for SMTP nodes.
If R/3 is in productive operation, it is advisable to reroute provisionally to another node.
You should therefore notify your system administrator.
Thanks
Anusa

Yes i completely agree, but we wanted to test this process by putting our own email addresses in the vendor master and then also maintinaing the condition records to make sure that the email are coming fine. I guess it was working until some time, but then yesterday i noticed this error message in our test client. Somehow we need tthis to get working so that we can get the signoff from the business and that this can be moved to production
Thanks
Anushga

Cannot enable ePrint Web Services - get internet connection error for HP LaserJet 1102W

I have a HP laptop running Windows 7 Professional 64 bit. We just changed over to Comcast internet service from AT&T where my HP LaserJet 1102W was set up for ePrint. After several hours, I was finally able to add the 1102W printer to the Comcast network, access the Embedded Web Server tool and print wirelessly but I cannot set up ePrint. I have deleted the printer but cannot get it to connect to Web Services. I keep on getting: Connection Error. Check Internet Connection but again, I can print wirelessly successfully to the printer but would like to be able to set it back up for ePrint. My Comcast router is an Arris TG862.
I have updated the firmware and used the HP Print and Scan Doctor tool but still am not able to get the ePrint Web Services to connect. Here is the information from the Networking page of the EWS:
IPv4 Configuration
Warning: A change in the IP Address will result in loss of connectivity to the browser.
IP Configured By: DHCP
Host Name: NPIC968F8
Domain Name: hsd1.tn.comcast.net.
IP Address Configuration
X Automatic IP Manual IP
X DHCP
BootP
X AutoIP
Manual IP Address:10.0.0.89
IP Subnet Mask: 255.255.255.0
Manual Default Gateway: 10.0.0.0
DNS Address Configuration
Preferred DNS Address: 75.75.75.75
Alternate DNS Address: 75.75.76.76
WINS Address Configuration
X Automatic WINS Server
Manual WINS Server
Manual Preferred WINS Server: 0.0.0.0
Here is my ipconfig information:
Wireless LAN adapter Wireless Network Connection:
   Connection-specific DNS Suffix . : hsd1.tn.comcast.net.
   Description . . . . . . . . . . . : Intel(R) Centrino(R) Wireless-N 1000
   Physical Address. . . . . . . . . : 8C-A9-82-A3-F9-5E
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   Link-local IPv6 Address . . . . . : fe80::c57:eb2b:5144:2ea5%13(Preferred)
   IPv4 Address. . . . . . . . . . . : 10.0.0.3(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Lease Obtained. . . . . . . . . . : Friday, March 29, 2013 1:24:52 PM
   Lease Expires . . . . . . . . . . : Saturday, April 06, 2013 11:09:24 AM
   Default Gateway . . . . . . . . . : 10.0.0.1
   DHCP Server . . . . . . . . . . . : 10.0.0.1
   DHCPv6 IAID . . . . . . . . . . . : 378317186
   DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-15-CE-4E-8C-10-1F-74-11-22-71
   DNS Servers . . . . . . . . . . . : 75.75.75.75
                                       75.75.76.76
   NetBIOS over Tcpip. . . . . . . . : Enabled
There appears to be a known issue with the Arris TG862 router and supposedly a new firmware is to be released soon but just checking to see if anyone has been able to resolve this issue.
Thank you!

Hi Surf1981,
I understand that you're not able to enable web services on your printer. I would try steps listed below.
1. Open an internet browser type printer's IP address.
2. Should bring you to the printer's status page.
3. Select networking tab at the top.
4. Left hand side select Network Identification.
5. Under DNS address Configuration select Manual DNS Server.
6. For Preferred enter 8.8.8.8
7. For Alternate enter 8.8.4.4
8. Select apply. You might get a warning saying this could interrupt connection that's fine.
9. Turn printer off for about 30 seconds then try again.
**If you find this helpful or want to say thanks make sure to click the white star under my name to give me Kudos. **

My email outgoing all appears with the wrong address, so it appears to be from my husband , not from me

When I send email to any one, I click on the the "from" box so it is from me.But when it is received it says it it from the other email address account on my computer, i.e from my husband

It may be that you have more than one outgoing mail account, and you're sending from the wrong one. From the Mail menu bar, select
          Mail ▹ Preferences...
The Mail preference dialog opens. Select the Composing tab from the row of icons at the top. From the menu labeled
          Send new messages from:
choose
          Account of selected mailbox
Note that this setting may have no effect if you start a new message while a VIP or smart mailbox is selected in the mailbox list. Those are saved searches, not actual mailboxes.
If the problem remains, select the Accounts tab in the preference dialog, then select the affected account in the list on the left.
In the Account Information pane, select the correct server in the menu labeled
          Outgoing Mail Server (SMTP)
If there's only one server in the menu, select
          Edit SMTP Server List...
and add a new server with the correct settings. If you're not sure how to do that, try the Mail Settings Lookup.
Another possibility is that the wrong card in your address book is selected as yours. Select your card in the Contacts application. Then select
          Card ▹ Make This My Card
from the menu bar.

How can I resend an IPhoto e-mail with the wrong address?

How can I resend an IPhoto e-mail that was returned because of an error I made in the address?

ImagineThat:
Welcome to the Apple Discussions. There is a 3rd party application, pdf-RecoverPro, that will let you lock the file to printing, changing, etc. You set two passwords, one to let the user view it and one to unlock the restricted features. Just provide the first password and send the file. You can try the demo version. It just saves one page in demo mode.
Do you Twango?
TIP: For insurance against the iPhoto database corruption that many users have experienced I recommend making a backup copy of the Library6.iPhoto database file and keep it current. If problems crop up where iPhoto suddenly can't see any photos or thinks there are no photos in the library, replacing the working Library6.iPhoto file with the backup will often get the library back. By keeping it current I mean backup after each import and/or any serious editing or work on books, slideshows, calendars, cards, etc. That insures that if a problem pops up and you do need to replace the database file, you'll retain all those efforts. It doesn't take long to make the backup and it's good insurance.
I've written an Automator workflow application (requires Tiger), iPhoto dB File Backup, that will copy the selected Library6.iPhoto file from your iPhoto Library folder to the Pictures folder, replacing any previous version of it. You can download it at Toad's Cellar. Be sure to read the Read Me pdf file.

Cisco Prime Infrastructure 2.0 cannot establish connectiont with WLC5508 7.4.110

I have two wlc 5508 in HA with image version 7.4.110. These two WLC are connected on two 6509 Catalyst Switch VSS system. On the WLC the LAG are enabled for the connection to the VSS. When i am trying to add the WLC to PI 2 once is succsessful. The connection continew working for a wile and after 3 hours or 5 hours or 1 day lost the connection between these two (WLC 5508 & PI.2) . After this trying again to add the WLC to PI.2 with no success . It became unreachable but the ping between the WLC & PI.2 its working fine.
It realy importand for me to add the WLC to PI.2 becouse it is the eyes for the APs for me.
Also the image of WLC 7.4.110 is compatible for PI.2 . I check it at cisco matrix files. Cisco also sugest 7.4.110 image for PI.2
any idea........?

The subject of the posting shows Prime Infrastructure 2.0 but in the body of the message you've got Prime Infrastructure 1.2
If it's in fact Prime Infrastructure 1.2 ::: 1.2 and 7.4.110.0 code isn't compatible
http://www.cisco.com/en/US/partner/docs/wireless/controller/5500/tech_notes/Wireless_Software_Compatibility_Matrix.html#wp92761
1.2.1.12
7.3.112.0
7.3.101.0
7.2.115.2
7.2.111.3
7.2.110.0
7.2.103.0
7.0.240.0
7.0.235.3
7.0.235.0
7.0.230.0
7.1.91.0
7.0.220.0
7.0.116.0
7.0.98.218
7.0.98.0
7.3.101.0
7.2.110.0
7.2.103.0
7.0.240.0
7.0.230.0
7.0.220.0
7.0.201.204
7.0.112.0
7.0.105.0
ISE 1.0
ISE 1.1
IOS12.2(50)SE
IOS12.2(50)SG
IOS12.2(33)SXI
If deploying Prime Infrastructure as a virtual appliance on a customer-supplied server, one of the following versions of VMware ESX or ESXi can be used:
•VMware ESX or VMware ESXi Version 4.0
•VMware ESX or VMware ESXi Version 4.1
•VMware ESXi Version 5.0
Note VMware Tools Version 4.1 is preinstalled in the Prime Infrastructure virtual appliance.

How can I change my user name? Someone else is using "phammm" my user name. At this point I cannot sign in with my email address and change my name. Help!

When I try to access the user forum, I have this problem. I am trying to access the forum for a problem with Firefox. NOte the typo; my user name is phamm.

hey...thanks for your post....ok I followed your instructions but seems this is what i had already done...
so say when I turn my computer on
I get
MAC OS X
Louise xOldsurnamex
Login user: Louise xnewsurnamex
Password-----------
So I have already changed the login name and it is the only one showing in accounts (and is admin)
What i want to change is the name above...I am unsure how to describe it? Basically the name of my computer???
Errr is this poss? Do you know what i am describing?
Thanx Louise

Cannot send e-mail - "The sender address invalid" error message

Today I keep getting this error message "The sender address is invalid - when i try to send e-mail. I checked my settings and they are the same as always - my e-mail address hasn't changed; the outgoing and incoming server information is the same. I went through the Troubleshooting steps and still nothing. Also it's taking a really long time to connect to check for incoming e-mails. Any clues on why this is happening or what I should try next? The e-mail is via Roadrunner does that matter (althoug it didn't a couple of days ago)

This message means that your outgoing email server is not letting you connect to send email. Maybe RR changed their policy. You should be able to send using home WiFi, but when using 3G RR will not allow connections from outside their network.
One easy way around this, is to use the built-in AT&T SMTP server for outgoing email.
Or, check the RR FAQs and see if they allow an authenticated account to send email - maybe you just need to add SSL and username/pwd on the RR outgoing email server settings.
BTW - this is asked almost daily - the "Search Discussions" box to your right would have given you many hits with the same answer.

Child DC cannot Replicate to Parent DC, because of connection errors. MS PortQryUI shows that ports 3268 and 3269 are not listening,

I started a support case with Microsoft to help me with raising the our domain Forest level because i received a message stating that there were Windows 2000 PDC still listed in the database. These PDCs were removed years ago. The tech saw all of the problems
i was having with domain replication so that is where he started. running the MS PortQryUI shows that ports 3268 and 3269 are not listening, (TCP port 3268 (unknown service): NOT LISTENING) when run FROM a Child domain controller against the Parent
Domain controller. Between the 2 Child domain controllers these ports are listening.
The Windows firewall is not running on any of the controllers, i removed a virus protect client from all of the servers, although i didn't enable the firewall there either, but these ports are still not listening on the Parent DC.
I need help debugging this. I am not very familiar with network sniffers so if i need to run one i'll need some guidance. This DC only has one NIC, all IP addresses are static, all servers are setup like this. All servers are in the same subnet, on the same
lan, on the same cisco switch, there shouldn't be anything blocking this port from starting.
I looked over other post that show this same problem, but they don't give a solution. If i am not using the Windows firewall why wouldn't these ports be open?
Any ideas? web searches are all over the map on trying to find the reason for this.
Bobby

Try running the below command on the DCs that you think have the ports blocked or all the DCs.
netdiag /test:ipsec /debug > c:\dcname-ipseclog.log
Open that from the C drive and see if there is anything saying block or filters.
Also, just for kicks have you disabled the firewall service on the DCs?
And just for kicks have you tried enabling firewalls ports on all the DCs? The KB is below
http://support.microsoft.com/kb/555381/en-us
Step 1 - netdiag results
Step 2 - disable the firewall service on all DCs if step 1 was negative
Step 3 - enable the firewalls on all DCs per KB 555381 if step 2 doesn't work
Let us know how it goes!
If it answered your question, remember to “Mark as Answer”.
If you found this post helpful, please “Vote as Helpful”.
Postings are provided “AS IS” with no warranties, and confers no rights.
Active Directory: Ultimate Reading Collection

Cannot Use Printer with my Photoshop CS5. Error Message.

I am encountering a problem that I never have before. When Click on File>Print I get this error message: "There was an error opening your printer. Printing functions will not be available until you have selected a printer and reopened any documents."
This happened suddenly. I had been printing with no problem just a few minutes prior. I did nothing unusual that I can recall to have caused this error message. I am using a Mac Pro using OS 10.9.5.
Thank you in advance for your help.

robert.englebright wrote:
station_two:
…Don't give advice if you are going to be insulted if people don't take it.
Don't ask for advice if you're going to feel insulted, period.
We're here to offer solutions and workarounds, not to debate with posters, specially about their "intuition" contradicting our responses. We don't offer our time to be wasted in that fashion. Can you possibly imagine what I care about your "intuition"?
A simple thank you or your silence would have sufficed. You didn't need to reply at all.
As always in the forums, if you don't like any response or post, you are entitled to your money back: $0.00.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
BOILERPLATE TEXT extracted from the FAQs:
https://forums.adobe.com/thread/375816?tstart=0
Do not be abusive or aggressive in your tone
An aggressive, demanding, accusatory or abusive sounding post will often evoke an aggressive or abusive and unhelpful reply.
Remember, you are not addressing Adobe here in the user forums. You are requesting help from volunteers users just like you who give their time free of charge. No one has any obligation to answer your questions.

WRT1900AC - DHCP providing wrong addresses

Deployed a WRT1900AC to replace a Fios Actiontect Router. I set the WRT1900AC as the primary. I changed the subnet to 192.168.2.0/24 and setup another router to act as the WAN for the actiontec to get the Caller ID info and VOD info.
Everything works exactly as expected except my wifi is not giving out the correct dhcp addresses. If I look in the logs I see the correct offer and then another offer right after that with the wrong address and I can't understand it. Everything else is working perfect and if I configure statics for the wifi clients it works fine.
Here is the output of the log -
DHCP client logLAN IP address | MAC address | Timestamp | Message type
192.168.1.219
24:A2:E1:41:89:09
2014-08-04T18:39:23Z
Nak
192.168.1.219
24:A2:E1:41:89:09
2014-08-04T18:39:23Z
192.168.2.105
24:A2:E1:41:89:09
2014-08-04T18:39:22Z
Offer
undefined
24:A2:E1:41:89:09
2014-08-04T18:39:22Z
Discover

jgiordano wrote:
Changed the MAC of the wrt to the MAC of the actiontech, had vverizon release the ip. Yes otn into wrt1900. I'm not home to get the model of the actiontech.
Back end router getting 192.168.2.101. All the rules work for forwarding.
I am fairly certain it's not the actiontech or the be router giving out additional ips as it doesn't do it when I'm connected via wire OR the guest wifi is enabled and I connect to that. Only the 2 & 5 ghz networks.
I didn't have to change the MAC address of WRT for it to work.

SMTP connection error!

Hi everyone,
Need your help, when I go to tcode SCOT there is too many errors in SMTP.
In SOST when I check the errors is as below:
"Message cannot be transferred to node SMTP due to connection error (final)"
Anyone can help me how to solve this error and let it send again by SMTP.
Thanks in advance,
Quare

Hi,
Pls see the foll note:
875136
BR,
Disha.
Pls reward points for helpful answers.

Connection Error while downloading games to N85

Hello
When I try to download or update games through N-gage for my N85 it always fails with the message: " A connection error has occured (30180-30180) followed by another error message saying the same thing, but without the error code.
Any ideas of whats wrong?

I have read of other users having this problem in the N-Gage discussion forum. One user solved his problem by using a WiFi connection, but obviously this is not ideal. Sorry, can't find the link to the specific discussion thread...you could try:
http://forums.arena.n-gage.com
Cheers.
If you found this post helpful, please click on the green "Kudos!" star. Cheers!

Nokia N95 connection error

Hi Guys,
I would appreciate, if someone could help me with Nokia N95’s connection error problem. I have my Nokia n95 from orange. From last two weeks every time I try to make a call, I get an error saying ‘Connection error’. I tried upgrading my phone’s firmware from version 10 to version 11 but in vain.
I tried talking to Orange support staff but they turned out to be clueless.
cheers...

I've had this randomly on my phone on O2 before. I didn't get it from O2 though.
I've read somewhere in the past this is a common occurrence with all symbian or n-series phones.
But i've been in the middle of a call on my N73 and it fades out and then flashes up "Connection Error" and my mate has had this quite frequently on his Orange N80.
Hope this helps.
Owned: Nokia 3510i, Nokia 3120, Nokia 6230i, Nokia 6233, Nokia N73, Nokia N82.
Current: Nokia N900!

Cannot establish TLS with SMTP...wrong address, connection error 5

Similar Messages

Maybe you are looking for