Canon 5320 stopped working as if no power.

canon 5320 stopped with no power. Tried new outlet, checked the cord, unplugged and replugged with on button depressed. No results. Not often used, so am disappointed with suggestions that printer is toast. Must be better answer

Hi bskaar,
If you have the unit plugged into a surge protector that is plugged into a power outlet, please plug the unit directly into a power outlet to see if this will power the unit back on. Please also try an outlet in another room of the house. If the printer still does not power on, it will require servicing. Please call or email us at one of the methods on the Contact Us page to obtain your servicing options.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

Similar Messages

Canon Selphy stopped working...

Hi. My Canon Selphy 510 photo printer stopped working with my macbook. It worked before, but now stopped. I was able to connect it to my g4 tower and get it to print from there (so we know it's not a hardware or cable issue), I was also able to print directly from my camera. I also have another printer on the network that is working 100% with this mac.
On the macbook, I uninstalled, then reinstalled the canon drivers. reboot, etc. no dice.
Here's the problem:
When you print, it fails. And the printer queue status goes back to Stopped. The normally lit green light blinks red just once.
At the end of this post is a clip from the error log (I set cups to debug loglevel for this). Notice how it thinks that it's out of paper and or ink, but it's not! I even tried to print without the paper in, to force it into a REAL no-paper-state, and this didn't help.
Let me add, the Canon Printmonitor application always just says Ready, and doesn't indicate any error state.
Do you guys have any ideas? Could there have been a software update I installed between now and when the printer worked that broke something? Thanks.
D [16/Jun/2007:06:42:58 -0400] [Job 34] JobManager converting file: /private/va
r/spool/cups/d00034-001 (7 args)
D [16/Jun/2007:06:42:59 -0400] [Job 34] `/private/var/spool/cups/d00034-001' ha
s 1 pages.
D [16/Jun/2007:06:42:59 -0400] [Job 34] PDFtoTiogaRaster: xResolution = 300, yR
esolution = 300
D [16/Jun/2007:06:42:59 -0400] [Job 34] PDFtoTiogaRaster: SheetWidth = 295.68,
SheetHeight = 579.72
D [16/Jun/2007:06:42:59 -0400] [Job 34] ImageableArea.origin.x = -0, ImageableA
rea.origin.y = 0, ImageableArea.width = 295.68, ImageableArea.height = 579.72
D [16/Jun/2007:06:42:59 -0400] [Job 34] frameWidth = 1232, frameHeight = 2415
D [16/Jun/2007:06:42:59 -0400] [Job 34] ColorSyncProfileID in PMConverterSetupT
icket is different from that in PrintSettings: expectedProfileID = 1580, actual
ProfileID = 0,
D [16/Jun/2007:06:42:59 -0400] [Job 34] PDFtoTiogaRaster USING DISPLAY LIST IMP
LEMENTATION
I [16/Jun/2007:06:42:59 -0400] [Job 34] kPMEventJobProgress:1 1 1 1 1 1 0
D [16/Jun/2007:06:43:00 -0400] [Job 34] sendJobProgressEvent: currentPage: 1 cu
rrentCopy: 1 currentSheet 1 percent: 86 isEndOfSheet:no
I [16/Jun/2007:06:43:00 -0400] [Job 34] kPMEventJobProgress:1 1 1 1 1 1 86
D [16/Jun/2007:06:43:00 -0400] [Job 34] sendJobProgressEvent: currentPage: 1 cu
rrentCopy: 1 currentSheet 1 percent: 100 isEndOfSheet:yes
I [16/Jun/2007:06:43:00 -0400] [Job 34] kPMEventJobProgress:1 1 1 1 1 1 100
E [16/Jun/2007:06:43:03 -0400] [Job 34] fatal: The specified Ink Cassette and P
aper cannot be found.^MReplace the Ink Cassette and Paper.
E [16/Jun/2007:06:43:03 -0400] PID 258 stopped with status 254!
D [16/Jun/2007:06:43:03 -0400] UpdateJob: job 34, file 0 is complete.
D [16/Jun/2007:06:43:03 -0400] StopJob: id = 34, force = 0
MacBook Mac OS X (10.4.9)

Hi there,
We have a Selphy 810 and I was going to test this on an Intel Mini, as I'm concerned it may be an issue with the PPC drivers on the Intel Mac, but unfortunately the power supply for the printer is missing so I cannot check this for you just yet. I'll keep on the hunt and hopefully have a reply soon.
In the meantime, what application are you trying to print from? If its a Universal app, then you could try setting the app to open using Rosetta. This would help to identify if its an Intel issue. Also, have you tried setting the Page Setup > Format for to the Selphy rather than 'Any Printer'?

Bluetooth Headphones Stop working after reboot or power cycle

I have some Insignia NS-BTHDP blue tooth headphones and whenever I restart my Imac or turn off my headphones they stop working. They still connect and the my Imac acts like it is using them for audio output but no sound ever comes from them. I have to remove the device and re-add it to make them work again.
I have seen other people with this issue but never a solution to it.

Thank you for your reply. Do I use one of those bottled air cans to blow out any dirt? Also I have used two different sets of earphones, one (Sony) has 2 rings and the other (Apple) has 3 rings. Thank you again for your advice.

WRVS4400N stops working, I have to power cycle to get it to work again

I own two of these Routers. One is at my business and the other one is at my home. I bought them with the intention of using VPN Tunnel. Initially I had nothing but problems with them. Over time and hundreds of hours later and through a select few of individuals, the problem was finally resolved. I could finally get the VPN tunnel to work. Of course they had to write a special BETA Firmware just for me, since apparently no one else that purchased these routers had actually setup or tried the VPN tunnel.
I just recently updated my Firmware to Firmware Version: V1.1.13. I've had the Firmware in place for about 1 1/2 to 2 months now as far as I can recall. Up until last week one of my routers will just work great for about 10-12 hours and then it just stops working. No access to router whatsoever. No Traffic, all lights on but no one home. The ports are getting quite HOT to the touch. I don't understand what is going on. Is my Router going out on me??? What should I do??

Its never a good sign when something is getting hot to the touch. This could be a sign that there is a hardware issue with your device. I recommend calling Cisco Small Business Support Center and let us troubleshoot this for you if the product is still in warranty.
Brian

USB ports have stopped working on my 975 power up platinum

For some reason the usb ports on the mb & the front of the case antec p160 have stopped working, I have not added anything new or removed anything, the firewire ports are still working though. I have tried removing the usb root hub restarting the pc and letting windows reinstall the driversbut it does not make any difference. Does any one have any idea what the problem my be.

He means what is in the thread labled "If you're having problems with USB ports, read on... "
The USB issue has followed several boards. Here is a quote from a post I've made on the subjetct.
Quote from: Frankeputer
Check to see if there is a wire running from your Front USB ports to the #10 slot of your USB block which connects to the motherboard header.
USB connector block layout which corresponds to the pin layout on boards with the Intel spec for USB. Do not cut the pin on the MOBO. You are removing/cutting the wire to the connector block from the case.
2 4 6 8 10(this wire, #10, not needed)
1 3 5 7 9(filled/key)
If you find a wire leading to the #10 spot on the block, remove that wire. My block has tabs so that you can pull the wire out, or you could snip/cut the wire leading to that position--if you cut the wire, be careful to cut the correct one and cut it in such a way that it may be repaired if you make a mistake. Make sure you wrap the wire, the exposed end/s, you remove/cut with electrical tape so as not to accidentally cause a short. I actually folded the wire back and wrapped it.
2 posts to read--Here and Here.
This seems to be a common issue involving many different case manufacturers. I don't know how it applies to other MOBO manufacturers, but in these forums it is not limited to a specific MSI model or supported chipset(Intel or AMD).

Yosemite - Canon printers stopped working 'filter failed'

This is a curious tale. I have a MBP Retina Late 2013 and connect to a Windows network. I have two Canon Image Runner printers on the network. To install them, I downloaded the drivers, then in ADD PRINTER, chose 'Windows' and chose the printers from the list presented. All good so far.
The printers have worked fine for 8 months.
Two weeks ago all MS Office programs started crashing whenever I tried printing from them. I've had issues with Office on a Mac before so, because I was very busy, I put dealing with this issue into the 'eventually' basket.
Last week Adobe Reader crashed when printing a pdf. Illustrator and InDesign printed fine, however, for a couple more days, but then they too failed to print (but the programs didn't crash). When I looked at the print queue I had the message 'Printing Stopped - 'filter failed'. This happened every time, whether I printed from any program (Word, Pages, InDesign, Illustrator, Reader, Acrobat Pro) or to either Canon printer. A search online threw up all sorts of reasons, mostly having to do with upgrading to Yosemite and the drivers being Sandboxed. But I had been printing successfully for months on Yosemite, and there had been no recent updates to the OS.
After contacting the firm's IT support (Windows, with few clues about Mac), they suggested uninstalling the printers and reinstalling them. Which is where things got really curious. I deleted all the printers, rebooted, and went to ADD PRINTER, but where the network had earlier given me a list of available printers, there was nothing. Also curious, I suddenly had an Oki laser printer installed (Bonjour). To satisfy my curiosity I printed something to the Oki printer, and it went through. I then searched through the building for an Oki printer, found it out in despatch, and sure enough there was my print job.
I tried to delete the Oki printer, but whenever I reboot it comes back!
At home I have several printers (all deleted when I purged the printers at IT Support's request) and I reinstalled them successfully. A Fuji-Xerox and 2 Brothers all print fine.
The problem, therefore, has to lie with either Canon printers specifically, the Windows network or ghosts. Nobody else uses my MBP and the IT Support denied any recent upgrade to the server or software.
I really, really, really would like to be able to print at work, and the guy out at despatch is getting annoyed whenever I send something his way. Has anyone had a similar issue, or does anyone know what the heck is going on?

Is it necessary for you to print via the Windows share? If not, then I would suggest you look at printing directly to the imageRUNNERs. To do so you will need to determine their IPv4 addresses, as the imageRUNNER series does not currently support Bonjour, so you will not see them in the Default view of the Add printer window. Once you have the IPv4 address for each imageRUNNER, you can add them by selecting the IP icon (instead of Default or Windows) and entering the IPv4 address. You then set the Protocol to HP Jetdirect-Socket and leave the Queue field blank. You can then change the Name from the IPv4 address to something more meaningful to you and you can enter a Location if so desired. Then the last step is to select the supporting Canon driver in the Use menu.
If IT says you must use the Windows share then the ability to see a shared printer has nothing to do with an installed printer driver. So when you select to add the printer and select Windows, you should see the list of Workgroups and Domain names. Assuming you do and select the appropriate one the Windows print server belongs to, then you should get a prompt to authenticate to the server. Here you can enter your Windows domain account and this should result in you seeing the shared print queue. Does this happen?

Canon 3000 stopped working, can't install drivers.

So, I've been using a canon 3000 directly attached through usb to my G4 for about two years now. Last week, all of a sudden, whenever I tried to print i would get a message on my print window that the jobs were stopped. The job would appear on the printer window but there would be a "job stopped" on the status. Whenever I tried starting the job from the menu, it would go into the progress bar for a few seconds and then go back to "job stopped". So i decided to delete the printer which i did through the printing prefrences panel and tried to reinstall the driver to see if that would help. When I tried reinstalling the driver the installer shows me the eula and then just gets stuck on "select destination" part, you know, where u select on what hd to install the driver. I get a little progress wheel that never stops and doesn't let me choose which hd to install the driver in. Yesterday I left my installer on in the morning, went to work and came back in the afternoon... roughly about 10 hours, and the progress wheel was still spinning as if the computer was still searching for a suitable place to put the driver. Any suggestions? btw, I've been reading that 10.4.11, the os I have, has a lot of problems with printers... wondering if that might be the case?

Your problem may be related to the .11 update but I don't believe that 10.4.11 has any particular problem with printers, most of my office Mac's are running this version and it has been one of the more stable releases (we had more trouble with .10). Your problem could be related to a number of things, most likely the disc permissions, so I would use the following steps to see if this can resolve your installation issue.
1. Open the Printer Setup Utility and delete the iP3000 from the printer list (if you see it). Then click on Printer Setup Utility and select Reset Printing System.
2. Close the Printer Setup Utility.
3. Go to Library > Printers > Canon and delete the contents of the BJPrinters folder.
4. Go to Library > Receipts and delete the file Canon iP3000 xxx.pkg
5. Empty the Trash
6. Unplug the Canon USB printer cable and restart the Mac
7. Install the latest version of the Canon driver. Looking at the Canon Au web site the latest version is 4.8.3.
8. Once the driver installation is complete, go to Applications > Utilities and open Disk Utility. Run the Repair Disk Permissions option.
9. When the Repair Disk is complete, open the Printer Setup Utility again and click Add.
10. Select the Default Browser view and select the Canon printer connected via the USB port. The Print Using menu should automatically change to Canon IJ Printer.
11. Click Add to add the printer.

Out of the blue, my computer stops working and refuses to power up. Can anyone help?

So I am posting this on a Thursday night. Monday morning and night, my computer was working fine. Come Tuesday, however, and my computer won't turn on. I don't think much of it; I shrug it off and head to school. Come back from school, and the computer still does not turn on.
Now I get worried. So I:
1,) I make sure the cords are all secure and plugged in, which they were. The computer is plugged directly into the wall; it is not on a power strip. The green LED lights up when i reconnect thew power cord after disconnecting it. But, after I hit the power button, the computer flickers and the light turns off.
2.) I swap out the power cord on my computer eith the one for the monitor. Still no luck.
3.) My friends told me it just might be dust. So I removed the shell, and used a can of compressed air. MUCH dust came out. I put everything back together, and still the computer does not work; the same thing occurs as was before.
4.) Now I go through a much deeper cleaning, removing fans and cleaning it all by hand, still to no avail.
I have tried everything I know to fix this thing. Know I am reaching out to the community. Anyone have any advice/suggestions? Has anyone also run into this problem? I own and mainly use an HP Slimline s5310y. This is the computer that broke. It's a 64-but computer running the Windows 7 (64-Bit) OS. Any help at all would be greatly appreciated!

Hi,
Try this procedure and see if you can isolate the issue. Trouble Shooting Power Supply Issues. Don’t skip any steps.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

DVI second monitor stopped working. Stuck in "Power Save Mode"

I have a HPE-110f Desktop PC. Monitor does not respond to all manners of troubleshoot e.g. update SW, disconnect reconnect. power save to "never" settings. Monitor checked on VGA and works fine. Status of Video Card infers working. Considering DVI adapter to VGA as stopgap to buying new Graphics card. Not a gamer but considering upgrade(s) to Radeon HD 4350 w/ P/S upgrade as well. Help. Prefer cheaper existing equipment fix.

Try connecting them all one at a time first and make sure each monitor functions as it should when it is the only monitor being used. Then try connecting the other monitors one at a time and changing the extending display settings. This is to see if there is a point in the process where it fails. Also, it could reset the settings to get it working again.
...an HP employee just trying to help where I can, but not speaking on behalf of HP.

Canon scanners stopped working with Acrobat X

I have Canon 4400F and Canon Pixma MP780 scanners installed as devices on my new HP Windows 8 (64 bit) computer. After installing Reader X I was able to scan with both devices without problems. After a Reader X update and a Windows 8 update attempting to scan from within Acrobat yields error messages. (" ... rmslantc.dll is missing .... " when trying to use the MP780 and " .... scanintf.dll is missing ..." when trying to use the 4400F. Both files exist in c:\Windows\twain_32\MP780 directory. Reinstalling Acrobat X without the update didn't help. I tried to do a system restore for a date when scanning worked but received an error message that the restore couldn't be completed. All drivers that are needed to run these devices are current. Any ideas?

TRy adding the folder that contain rmslantc.dll in the PATH environment variable. Follow these steps:
a)    First, determine the correct path to add into the PATH environment variable. Look inC:\Windows\twain_32 and there should be one other folder (Example: - MP780). This is the path that is needed to be added into the PATH environment variable. C:\Windows\twain_32\MP780
b)    Modify the PATH environment variable. Go to Control Panel, System, and then choose Advanced System Settings in the left hand column.
c)    This will bring up the System Properties dialog (it should already be on the Advanced tab).
d)    At the bottom of this dialog is an Environment Variables button. Clicking this button will bring up theEnvironment Variables dialog.
e)    In the bottom panel, scroll until you find the variable named Path. Select this one and then hit Editbutton to bring up the Edit System Variable dialog.
f)     In the Variable value text box, scroll all the way to the right and then add in the pathC:\Windows\twain_32\MP780that was determined earlier. Make sure to separate this value with a preceding semi-colon.
This should resolve the issue because I see lot of people facing this issue as mentioned in the following forums:
http://answers.microsoft.com/en-us/windows/forum/windows_7-hardware/twain-errors-when-usin g-canoscan3200f-on-win7/8f4c399b-52ab-4d37-8255-35d5b5cd0b3a?msgId=f4f1873e-9f23-449f-a86f -699512bb05fe
http://aaron-kelley.net/blog/2010/10/canon-scanner-error-cant-find-rmslantc-dll/

Canon Printer stops working (software issue?)

have my Canon iP4200 printer hooked up to my iMac and have been using it for years with out any problems until today. When i try to print something nothing happens. In the Printer queue application thing in the dock, it shows the document in queue and its status is "printing". On top of the window it shows this message: 'GenericClass: waiting for device' whatever that means i assume thats the issue but have no clue what it means. I have so many things to print for uni and need to get this working again, how do i get it back to working order again??

I did all of that and didn't seem to work. However i think the issue is with VM ware Fusion, because everytime i have that open it displays that printer error msg (regardless whether im printing on Mac OS X or XP), but when VMF is not running it prints fine...

10.6.7 : canon scanner stops working

Hi,
I updated to 10.6.7 and since then my MP750 canon scanner isn't recognized any more. I tried to reinstall the scanner driver downloaded from canon website but with no luck... This worked for the 10.6.5 -> 10.6.6 transition.
Printing on this multifunction is working though...
The only workaround I found is to use ... windows XP in virtualbox

Update : re-installing the file called "mp750osxsd12131ej7.dmg" solved my issue.
Cheers.

My phone just randomly stopped working. it won't power on at all. how do i get it fixed?

my phone just quit working out of no where and my lock button doesn't work, i tried charging it and everything, but my phone just won't comeback on. i've read you can get your phone replaced for 270ish, but i don't have insurance, does that still apply, or no?

iOS: Not responding or does not turn on
Locate a Service Center
Call Apple for Service and Support
Set up service on your own or check options and warranty
Questions about service and potential costs (Choose your country after selecting your product)

Canon MX870 Stopped Working

We had a paper jam, cleared it out, and now the printer won't work at all. It acts like it's printing (makes all the usual printing noises, etc) but nothing comes up on the paper. Ink cartridges are good. I tried printing one of my receipts for a local food co-op as a test and all it did was print the 2 horizontal black lines that were part of the receipt - none of the text printed. Any ideas?

Thank you! We're on Windows 7. We were getting an error message with the paper jam, but once we cleared that out, the error went away. It acts as though it's printint correctly...makes all the normal noises, the paper comes out, but comes out blank (except for those horizontal lines which it seems to be able to print without a problem for some reason). It's very strange.

Power Book G4 , Spot Light and other search app stopped working

When I use spot light on my iMac G5 it always worked , but has stopped working on my G4 Power book OS 10.4.7, I went to the new Apple store and was given a procedure to follow but it did not change the situation, Un fortunately I cant remember what it was , It involved dragging the hard drive into and application, should I just reinstall from the tiger CD ?
G4 powerbook and iMac G5 Mac OS X (10.4.7) iLife6

Was it this procedure?
http://docs.info.apple.com/article.html?artnum=301562

Canon 5320 stopped working as if no power.

Similar Messages

Maybe you are looking for