Catalyst Control Center stopped working properly after widows update

When I let Windows Update install the newest catalyst control center driver I could not open catalyst control center so I tried to do a system restore but it failed because It said my anti virus was preventing this with the error code 0x80070005.I first tried to disable the anti virus shields and restore didnt work. Then I uninstalled the anti virus and went to safe mode but it gave my the same error. Now Catalyst Control Center opens but the only feature available is HydraVision. I still cannot change the picture and graphics settings because they are not there to select in CCC.

Hello , Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More. I understand that your Catalyst Control Center (CCC) program on your desktop computer has stopped working correctly after downloading Windows update drivers for it, and I would be happy to assist you in this matter! To correct this issue, I recommend returning your system back to a previous restore point to before the Windows updates were installed. This can be done by following this resource on Using Microsoft System Restore (Windows 7). Once the restore point has been enabled, you can update your CCC and graphics drivers by following this document on Using HP Support Assistant (Windows 7). Please re-post with the results of your troubleshooting, and I look forward to your reply!
Regards

Similar Messages

Catalyst control center stopped working

HP Pavilion HPE h8-1287c
Video card Radeon HD 7450
Windows 7 64-bit
Error message "Catalyst Control Center stopped working......."
Two monitors connected, HPw2408h and TV. HP monitor is connected using DVI and the TV using HDMI.
The issue is that when the pc starts things run fine. WhenI want to have the sound to the TV I switch the Sound Playback to AMD HDMI Output and the TV now has the sound. After a while I will get an error message "Catalyst Control Center stopped working.......". When Sound Playback is opened the AMD HDMI Output is no longer working and has a red arrow pointing down and it indicates the AMD HDMI Output is "not plugged in".
I have download the latest drivers and still have the same results.
What is needed to correct the issue?

Hello insco6750,
When you updated the drivers did you install over top of existing software or uninstall beforehand?
First we should try ripping everything ATI off of the system, including software, drivers and CCC. You should be able to uninstall everything through Add/remove programs.
After you remove everything reboot and let windows reinstall it's own drivers and software. You don't need CCC to do dual monitors so we can do testing without it.
Once you let windows install see if your HDMI output no longer works when you switch to the TV.
Post back your results after completing this.
If I have helped you in any way click the Kudos button to say Thanks.
The community works together, click Accept as Solution on the post that solves your issue for other members of the community to benefit from the solution.
- Friendship is magical.

Aluminum Wireless Keyboard not working properly after Firmware update 1.1

Hi,
Well, as the subject says, my keyboard is not working properly after I updated the firmware. The problem is that several keys (delete, down arrow, brackets and apostrophe) stopped working right after I installed the update. I never dropped it or hit it. And I did not stop or interrupt or did anything during the install. I take very good care of it.
I have already tried toubleshooting with the support page, restarting the iMac, taking off the batteries, setting it up with bluetooth again, going back a week with time machine and to reinstall the firmware. So, if you have something new for me to try, I will really apreciate it.
Thanks in advance.
Franco.

I have 24" iMac with the Apple wireless M&KB - I know this is basic but have you tried a fresh set of batteries? My KB will refuse to establish connection when batteries are on the weak side the firmware update may just be a co incidents. If your wireless mouse is working OK then I would guess the blue tooth is functioning.
Not sure about the 10.49 download - are your other file downloads completing properly? Are there any error messages?
Steve

Catalyst control system stop working

recently i upgrade my laptop from windows 8 to 8.1 my laptop is hp pavilion e015tx after updating operating system when i try to open "configure switchable graphics" or " graphics properties" it will not open and give message "catalyst control control system stopped working"
please help me some one

Hey @prakhar12 ,
We meet again!
The CCC software may need to be updated to work on Windows 8.1.
Please try installing the most recent version from the HP website here: AMD High-Definition (HD) Graphics Driver.
This package contains the drivers for both the Intel and AMD GPU so that your switchable graphics will work in Windows 8.1.
Let me know if that helps!
Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
The Great Deku Tree
I work on behalf of HP.

Why did the Notification Center and Control Center stop working?

After updating ios 8, Notification and Control Centers stop working from time to time. I can't swipe up or down. I have to use the Assistive Touch to bring them on screen. Restarting the iPhone make them usable again. But afyet a while, it happened again.
Now, iOS 8.1.2. Last update, the Centers used to appear again. But 8.1.2, they just stopped working.
How how can I fix it?

Hello Eric Grylls,
Thanks for contributing to the Apple Support Communities.
If you're not able to access Notification Center or Control Center (other than using Assistive Touch) on your iPhone 5s since the latest update, I recommend following these troubleshooting steps mentioned in this article:
iOS: Not responding or does not turn on - Apple Support
If the device is unresponsive or if certain controls aren't working as expected, restart your device.
If the device remains unresponsive or does not turn on (or power on), reset your device.
If the above steps do not resolve the issue, or the if the screen remains black or shows a persistent Apple logo, try restoring with iTunes:
Connect the device to your computer and open iTunes.
If the device appears in iTunes, select and click Restore on the Summary pane. Learn more about restoring iOS software.
If the device doesn't appear in iTunes, try to force the device into recovery mode, and then restore it.
If the above steps do not resolve the issue, contact Apple.
All the best,
Jeremy

Swipe down/up for notification and controle center stop working

Hi guys,
I got today my new IPhone 6+ running iOS 8.0.2 and after a while the swipe up gesture for the control center and also the swipe down gesture for the notification center stops working on the home screen and in apps.
On the lockscreen the gestures still working.
It happend now 3 Times today but I can´t see any System behind this.
And it happens also that the System freezes some times for a few seconds, I saw it happen In safari and mail app.
Hope these are only bugs in iOS which will be solved soon.

Hello Eric Grylls,
Thanks for contributing to the Apple Support Communities.
If you're not able to access Notification Center or Control Center (other than using Assistive Touch) on your iPhone 5s since the latest update, I recommend following these troubleshooting steps mentioned in this article:
iOS: Not responding or does not turn on - Apple Support
If the device is unresponsive or if certain controls aren't working as expected, restart your device.
If the device remains unresponsive or does not turn on (or power on), reset your device.
If the above steps do not resolve the issue, or the if the screen remains black or shows a persistent Apple logo, try restoring with iTunes:
Connect the device to your computer and open iTunes.
If the device appears in iTunes, select and click Restore on the Summary pane. Learn more about restoring iOS software.
If the device doesn't appear in iTunes, try to force the device into recovery mode, and then restore it.
If the above steps do not resolve the issue, contact Apple.
All the best,
Jeremy

Firefox stops working properly after a period of time

btw, I can't type in this box. I'm typing this in another program and pasting it in.
Using Firefox 5. I just installed Lion yesterday for Mac, but this problem occurred even before I did so. After a period of time, FF stops working properly. I notice it when I try to open a new tab. It won't switch to the new tab and the screen turns blue. If I type in a web address, it looks like it tries to go there, but it doesn't. When I look at any other already open tab, it has the blue screen. I have to restart to get my proper web pages back.

Whenever I click on "More System Details" there are several things I hope I won't see. Your Conduit Engine is one of them. It is malware by any reasonable definition and a cause of major problems with Firefox.
Google for information and advice as to how to get rid of it. Someone may come along with more specific advice..
If things aren't perfect after that you could do some straightforward troubleshooting(Safe Mode, Problematic Extensions, Hardware Acceleration etc) - in default theme -
https://support.mozilla.com/en-US/kb/Troubleshooting%20extensions%20and%20themes

ITunes / iPhone not working properly after newest update...

iTunes is not working properly after the newest update... It dosen't see my iPhone, the program acts very sluggish, and has trouble loading the Store. Anyone have a solution or an explanation? I have tried the suggestions found in other threads ie. restart, re-download, charge phone, restart phone and so on. Nothing works. Everything was working fine until iTunes and the new ios were installed. After that it all went to crap. Thanks, Randy...

Close your iTunes,
Go to command Prompt -
(Win 7/Vista) - START/ALL PROGRAMS/ACCESSORIES, right mouse click "Command Prompt", choose "Run as Administrator".
(Win XP SP2 & above) - START/ALL PROGRAMS/ACCESSORIES/Command Prompt
In the "Command Prompt" screen, type in
netsh winsock reset
Hit "ENTER" key
Restart your computer.
If you do get a prompt after restart windows to remap LSP, just click NO.
Now launch your iTunes and see if it is working now.
If you are still having these type of problems after trying the winsock reset, refer to this article to identify which software in your system is inserting LSP:
iTunes 10.5 for Windows: May see performance issues and blank iTunes Store
http://support.apple.com/kb/TS4123?viewlocale=en_US

Catalyst Control Center crashes with new video driver update

Hi Folks,
I just updated to the newest rev of the ATI driver (April 28, 2009). Now, catalyst control center crashes at startup, opening a dialog box that says, "catalyst control center monitoring program has encountered a problem and needs to close".
Has anyone else run into this? Any ideas on how to fix it?
Thanks,
Allie
T400 2764-CTO, XP

Please post the details of your problem with the 8.563 driver in this thread.
Use the format from this post.
T500: Vista 32, 2.8GHz, 4GB RAM, 15.4" 1680x1050, 500GB 7200rpm, ATI Radeon HD3650 + Intel 4500MHD. T42: XP, 1.7GHz, 2GB RAM, 14.1" 1024x768, 250GB PATA, ATI Radeon 7500.

Load MMDriver and Catalyst Control has stopped Working

I have an Notebook Pavilion dv7 -6c00
Two days ago I Installed Adobe Premiere, and when I try to run it i get a error message that says somethink like they can't find a video module, I google it, and some people says that I have just to update my Graphics card driver. So I go to AMD page, and download the last catalyst control..
Since then I can't open firefox, Games, and other thinks because Load MMdriver crash and when I try to open Catalyst control it's the same.
I try:
- To install de original drivers with the Recovery manager. (nothing happen)
- Uninstall the catalyst control... was the same...
- To Restore the system with Windows Restore point... and then I get a error and it delete my point of restore, and don't solve the problem eather...
¿So what I have to do? I read this topic: http://h30434.www3.hp.com/t5/Notebook-Display-and-Video/Update-to-windows-8-1-Load-MMdriver-not-resp...
They recommend to install that drivers in that order, I already download the driver for my specific model... but I'm worry about that "update" will crash another things.... Which is the solution to this problem?
This is a picture from google that shows my notebook model, (just to comfirm my model Pavilion Dv7-6c00).
http://blog-imgs-50.fc2.com/d/i/g/digimonolog/Windows-Live-Writer_HP-Pavilion-dv7_C0F1_IMG_0021.jpg

Well First, Thank you a lot for answering.
My OS is Windows 7 (64 bits). Sorry I forgot to put it in the message.
I did not explaing mysell correctly. I did not the Recovery System from the partition yet, I just did the System Restore from a Restore's point. (EDICTION: more exactly, The AMD Driver from AMD web pages, also install the Microsoft Visuall C++ 2000, and maybe it was my biggest mistake, to choose it like the point to restore, and not before it... from that point it start the problems, when The restore finished it's said something like: "There was a error, and the restore couldn't complet... but it's indeed restore, but it erased the rest of restore points. I also have to add that It wasn't the first time that I restore, I mean, I install one driver from AMD and like I doesn't let me to run Adobe premiere, I restore to another point, and try another Actualization of Catalyst control manager, and it's in that moment, when it eather solve the problem, when I restore to the point when Visual c++ 2000 was installed, an all my nightmare begins)..
When I mention the Recovery I was talking about HP Recovery Manager, it let me reinstall the original drivers without the reformat/recovery the laptop. I used it to reinstal the original AMD Driver... but it doesn't solve the problem.
I did not the recovery because I would prefer not to have to reinstall all my programs. (But it's the ultimate solution XD).
I figure out that maybe the problem is in the Intel's Graphics Driver, (I didn't mention it, but my laptop has switchable Graphics, I think that's how it's called XD). I think that's the problem because when I used the HP Recovery Manager to reinstall my Intel's Graphics Driver I get this Error:
http://s10.postimg.org/rua6ahk7d/Untitled.jpg
Also I can open the programs that I mention just when I go to Divice Manager and Disable or Unistall that Intell Graphics Drive (but it reinstall automatic when I: "Right click > scan for driver changes"). I can't find it in the "Add or Remove Programs" so I can't unistall the driver to prove with the HP Recovery Manager.
http://s29.postimg.org/g0r05dhzr/Untitled.jpg (Device Manager picture that shows my graphics Drivers, selected the one that I think it's the problem).
Then I don't know what to do. I really don't want to Recovery the pc, with the Recovery partition. I would prefer to try another options before (if exist any).
Thanks for Aswering, and excuse me my english, I'm not native... like I think you already guess. XD If I didn't explain somethin well I will try no explaing it better .
PD: When i have the intel driver Active, I get the message: " --Programs-- has stopped working" The --programs-- can be: Catalyst control, Skyrim (game), the HP Recovery Manager It's self, Firefox, and any thing that could use the graphics card (I don't get it why it happened with the HP Recovery Manager app that I shows in the picture... but it happened, i have to Disable the driver to get printscreen....
http://s9.postimg.org/logt6h62z/Untitled.jpg
PD2: Sorry I didn't mention all this in the first post, I was a little hurry when I writed it.

External WD HD stopped working properly after routine software update

Hello
I have WD my studio external HD connected to my iMac 24" early 2009 with OS 10.6.8. This morning everything was working fine, but then I updated the software after I was prompted. I had not updated the software since last july.
After the update, I got a message saying that the external HD could not be repaired. Very strange, as it was working perfectly before the update. I tried to restart the computer, but i got the same message.
I tried the few usual things (unmounting, disconnetting, repairing with disk utility etc,) with no success. Everything behaves funny, in the sense that sometimes the HD does not mount, sometimes it mounts, but it has a different icon (I used it to back up with time machine), sometimes it is greyish in the list of HD in finder, and I can't change permissions on it (i have write and read permissions, but they're greyish and there's nothing i can do).
Any suggestions?
thanks

I tested it on another computer and it works perfectly.
On my regular computer, when I start it, i get this message "Mac OS can't repair the disk "My Book". You can still open or copy files on the disk, but you can't save changes to the files on the disk. Back up the disk and reformat if as soon as you can".
As I said earlier, the problem occurred after I updated the software (the software updates that Mac OS always suggests). I worked perfectly before the update, and I got the error message when the Imac restarted after the update.
Suggestions?

Printer is not working properly after I updated OS

My printer is not working after I updated my OS software. It will only print out pages as a mirror image. All the programs are not printing properly. Could really use some help fixing this issue.

What software did you update?
It is very difficult to offer troubleshooting suggestions when the "os version" you are using is unknown as each os has their own troubleshooting solutions.
Please describe in detail all you have attempted to do in order to resolve the issue. Have you contacted the printer manufacturer tech support? Read the printer's user manual? Your printer drivers updated to match your updated software?

Help! Trackpad gestures are not working properly after Yosemite update

So yesterday I updated my MBA to Yosemite. And since then I'm facing severe problems with my trackpad. Scroll and click gesture works as usual, but the other gestures suddenly stops working. I even checked my trackpad settings, but couldn't find any setting issues there. They won't just respond to any. Is it just me or everyone is facing such issues.

worse than that, my MacBook Pro FREEZES when using 4 finger swipe on the built-in trackpad for App Expose after upgrade to 10.10.1
Before 10.10.1 everything was working fine. Now, about one third of the time I use the 4 finger swipe the computer is dead (apparently mostly when using Numbers). I can still use the mouse but no response to clicks, keyboard, trackpad, or screaming out loud. All I can do is turn it off!
This (in combination with Mail issues) is so bad that for the first time since using Mac I start thinking going back to PC...

Smart Actions not working properly after software update

My Razr updated 2 days ago and since then my Smart Actions are not working properly.
I have my Work action set to turn the volume down when I'm at a certain GPS. It shows that "Work" is active, but doesn't turn the volume down.
Also, there are times (since I've owned the phone) that it will not connect to the network after coming off a Wifi Connection without rebooting the phone. I took it into a Verizon store and they did a hard reset, and that fixed it for a time, but it started doing it again.
Any help appreciated.

Hi mcclainkb, Let's make sure your phone works as you expect it to! Have you tried removing the Smart Action and setting it back up again? Are your other GPS services working as normal? After the hard reset performed in the store did you install all of the same application that you had before?
Thank you,
YaleK_VZW
Follow us on Twitter @VZWsupport

Ipad2, safari does not work properly after ios6 update. How do I fix it?

I need help in fixing safari problems after ios6

With the amount of information you've provided it's impossible to offer a potential solution. We can't see your computer so we need to know the details of your problem and setup, i.e.:
what version of iPhoto are you using?
what system version are you running?
what do you mean by not working properly? Explain in detail.
what fixes have you tried?
where is your library located?
did you apply any updates or upgrades just prior to the problem occurring?
are you running a "managed" or "referenced" library?
what type of Mac?
how much free space on your boot drive?
OT

Catalyst Control Center stopped working properly after widows update

Similar Messages

Maybe you are looking for