Changing port configuration with Event Manager

Hello,
I'm trying to change the configuration of a port when the port goes down with EEM.
So when an flex connect access-point is disconnected the port becomes an access-port.
I don't want to use the MAC address.
Does anyone has experience with this.
Below is the applet I'm using.
Thanks in advanced,
Michel
event manager applet CONFIG-ACCESS-PORT
event neighbor-discovery interface regexp "(FastEthernet[0-9]\/[0-9]+)" cdp delete
action 100 regexp "(AIR-LAP)" "$_nd_cdp_platform" value
action 110 if $_regexp_result eq "1"
action 200 cli command "enable"
action 210 cli command "config t"
action 220 cli command "interface $_nd_local_intf_name"
action 240 cli command "switchport mode access"
action 250 cli command "switchport access vlan 20"
action 260 cli command "no switchport trunk encapsulation dot1q"
action 270 cli command "no switchport trunk native vlan 88"
action 280 cli command "no switchport trunk allowed vlan 88,100"
action 290 cli command "spanning-tree portfast"
action 400 syslog msg "EXECUTED EEM APPLET FOR ACCESS-PORT interface $_nd_local_intf_name"
action 500 cli command "end"
action 510 cli command "copy run start"

Hi Evan,
For sure! There is a really good example on the configuration guide, and assciated caveats.
http://www.cisco.com/en/US/docs/wireless/controller/7.4/configuration/guides/consolidated/b_cg74_CONSOLIDATED_chapter_0100011.html
Benefits for using LAG is increased bandwidth, and redundancy - especially if you have the two (or more in the case of a 5508 WLC) ports connected to different physical switches, eg a 3750 stack.
Best,
Evan

Similar Messages

Solution Monitoring configuration with solution manager 4.0

Hi Friends,
I have to the Solution Monitoring configuration with solution manager 4.0.
Please provide steps or screen shot if any body having that.

Hi,
Check <a href="https://websmp108.sap-ag.de/sapidb/011000358700005479192006E.sim">this.</a> and <a href="https://websmp108.sap-ag.de/sapidb/011000358700006936062005E.sim">this</a>.
This will solve your problem.
Feel free to revert back.
--Ragu
Message was edited by:
Raguraman C

Problem with Events Manager: 'slct'

I set up an Events Manager item to run a script whenever the event "Selection" ( 'slct' ) is activated. The script works beautifully and I'm having no problem with the script itself. I am, however, having problems with what happens after the script finishes. I have this problem even if I completely comment out the script or delete everything inside the script file and leave it blank. The purpose of the script is to automate things when I select specific layers. That works and the script has some checks to prevent anything from happening unless one of those specified layers is selected.
The problem is, when I select a tool using the keyboard shortcuts, it will revert back to the previous tool upon the next keypress. It basically acts as if I am using toggle mode for that tool by holding down the key for that tool.
I wiped out my preferences but that did not solve the problem. It makes no difference how my keyboard shortcuts are mapped...either default or user defined. So for an example, here is how some of my keys are mapped:
B-Paintbrush tool
S-Brush Size Increase
So if I'm using the Clone Stamp tool and want to switch to the Paintbrush tool, I will press the "B" key. The tool switches as it's supposed to. If I need to change the size or hardness of the brush, I press one of the corresponding keys...let's say "S" to increase size. When I press "S" nothing will happen until I release that key. Once I do release it, the tool switches back to the Clone Stamp tool. You can get this same effect yourself if you hold down the key of the tool you are switching to (use the toggle mode) and then try to change size/hardness using the keyboard shortcut for that function while still holding that tool's key down.
If I select the tool from the Tools Palette, I do not have this problem. If the tool is selected from within my script, I do not have this problem. The only time I have this problem is when using the keyboard shortcuts to select the tool.
Keep in mind that I have tried this with the script code completely bypassed/erased so no script code actually exedutes. When I turn of the Events Manager or remove the 'slct' item from Events Manager, I do not have this problem at all. If I hold the <SHIFT> key down while selecting the tool, I do not have this problem (this is the same as if you were to hold down the <SHIFT>+<tool key> and press the key to change size/hardness).
To me, it seems as though if there is a 'slct' event item in Events Manager and the keyboard is used to select a tool, Photoshop treats it as if that key is being held down (toggled) until another key is pressed (or even the same key).
If anyone knows how to get around this problem, I would greatly appreciate it. Thank you.

I'm having the same problem where a keystroke (like changing size "[ or "]") will revert to a previous tool rather than change size. Particularly annoying when you left your previously selected eraser slightly larger or smaller than your brush size and don't realize it till you've erased.
So far, from reading across quite a number of forums, it seems the event listener istelf causing the issue
At the moment I've just been thinking of "BB" as my shortcut instead of "B" so when it reverts it reverts back to the brush anyway.
I'll come back if I find a real solution to this annoyance ;P
CS5
Wacom Intuos4
Windows7

Dealing with Event Management

Dear All,
Our client - an Indian PSU wants to manage the events ( any show's , special events ) happening on their premises handled by them in SAP .
Kindly suggest the SAP module in which it will suite the best . As there are two modules like - Training and Event Management (HR) and SAP Event Mangement (SCM) under HR and SCM. Which will be the best module for handling Event Mangement .
Suggest me the best with more information if you have come across such a senario's.
Thanks in advance..
Alok

Hello Alok,
SAP Event Management is used for Tracking and Tracing in your Supply Chain. You can e.g. track a container and send out events in case of delays or if a proof of delivery is posted.
More information is available on [SCM |http://service.sap.com/scm] on the right hand side click on Event Management and hava a look e.g. on SAP Event Management 7.0 - Overview
Regards
Berthold

Changing map configure with OMB

Does anybody know how to change map configuration settings with OMB+? I would like to change bulk size, commit frequency, max number of errors, etc.. I could not find a good example of how to do this. Any help would be appreciated.
OWB Client vesion: 10.2.0.3.33
OWB Repository: 10.2.0.3.0
Thanks,
Nick

It may be the mapping has not been analyzed so it is in an early design phase when either the PLSQL (batch) or SQLLoader properties are not available. If you perform these configuration settings after the operators have been added and the map designed then I think you should be OK. If this still fails try performing an OMBVALIDATE on the mapping before settings the config properties.
Cheers
David

EX60 configuration with Call Manager 9.1

Dear All,
I am running CUCM 9.1
I have an EX60 Device which i need to register with call manager 9.1
Please provide the steps to perform this task and bring it into a working condition
Will be thankful for your response.
Regards,
Malik.

Hi Malik,
Here we go
http://www.cisco.com/en/US/docs/telepresence/endpoint/codec-c-series/tc6/administration_guide/administering_endpoints_running_tc6_on_ucm90.pdf
Cheers!
Rob
"go easy...step lightly...stay free "
- The Clash

Health Monitoring and Restart Configuration with Node Manager

We have a WL 9.2.2 instance setup using Node Manager to control it. It contains a JMS server with a persistant store that is in an oracle database. If the Oracle database becomes unavailable, the Weblogic server throws a number of errors eventually leaving the Managed Server in a "FAILED" state. I configuring/activated the following "Configuration - Health Monitoring" options for the managed server to have it automatically recover from this situation:
Health Check Interval: 180
Auto Kill If Failed: Checked
Auto Restart: Checked
Max Restarts Within Interval: 2
Restart Delay Seconds: 0
However it is not automatically restarting, even though the server shows in a "FAILED" state.
1st question: Do I need to restart the server with the settings above to have it react to the FAILED state? I would think that 3 minutes after I configured the above it would begin a restart on the FAILED server, but that does not happen
I also note on the "Configuration - OverLoad" page, there is a setting for "Failure Action:" that can be set to "Ignore, take no action" or "Force Immediate Shutdown of this server" I did configure/activate this for "Force immediate Shutdown..." but again the currently FAILED server does not restart.
2nd question: Does this "Configuration - Overload- Failure Action" setting override or effect in any way the configuration of restart on the "Configuration - Health Monitoring" page?
3rd question: Same as 1st question but for these Overload settings: Do they require a full restart of the managed server to somehow take effect?


Have you set the field : CrashRecoveryEnabled=true in file : ..\bea\weblogic92\common\nodemanager\nodemanager.properties ?

Changing zoom angle with transition manager

Hi guys and gals,
I'm making a map and would like to be able to zoom in and out
of counties. I've got most of it down I believe, but would like to
be able to control where the zoomed in image ends up. I'm using the
transition manager information I found
here.
Here is what my code looks like:
_root.img_dunn_mc._x = 82;
_root.img_dunn_mc._y = 235;
mx.transitions.TransitionManager.start(img_dunn_mc,
{type:mx.transitions.Zoom, direction:0, duration:.5});
The x and y values are to make it appear that the county is
zooming in from a specific spot on the map. When it zooms in, it
simply makes the clip bigger. Is there a way to control the x and y
coordinates of the zoomed in image?
Wow, I hope that made some sense.
Thanks!
Matt

It used to work perfectly fine - if I changed my mind while watching/fine tuning an edit, or wanted to see what the other angle would look and I had already put a crossfade, it would be a seamless transition between the two...the clip would change to the beginning of the edit, not to the end of the transition (and I could then remove the transition as it was superfluous). Which is why it came as a surprise that all of a sudden it has stopped working

AIP-SSM configured with event action "produce alert", but it drop packets

Hi, I configured an AIP-SSM IPS on event action for "Produce Alert", but when fire a signature, it drop the packets. So, what will be the problem?

Try these links:
http://www.cisco.com/univercd/cc/td/doc/product/iaabu/csids/csids11/cliguide/clievact.htm#wp1034058
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a00807335ca.shtml

Dynamic file send port configure with variable store path location

hi ,
i done like dynamic file send port:
Port_7(Microsoft.XLANGs.BaseTypes.Address)="sw"; --> sw is path location string type variable
Port_7(Microsoft.XLANGs.BaseTypes.TransportType)="FILE";
here sw is path location :C:\Users\00134\Desktop\Rec\sqltest\senddate.
but it is not working where im wrong?

try this
Port_7(Microsoft.XLANGs.BaseTypes.Address)="file://"+
sw +@"\%MessageID%.xml";

APN configuration with Profile Manager password payload

hi all,
I have succesfully enrolled an iPhone using Active Directory credentials. The standard profile configures mail too, using credential given during login to /mydevices web page. My problem is that I can't configure APN (3G) settings in the same way...I can put username (%short_name%) in the APN username field, it works, but I can't find a solution for a password request (or any other way) for let users put their password for APN access during enrollment process...
Is there any way to do it?
Thanks
Ale

Same issue under 10.7.4.
I pulled a console log from the F5 BIG-IP app and found this error when the iPad tries to install the VPN profile:
com.apple.managedconfiguration.profiled profiled[1018] <Error>: VPN: couldn't create vpn interface
Doesn't realy explain WHY it can't create the interface though.

Training & Event Management - Integration with FI

Hi,
In the standard configurations Training & Event Management is integrated with Controlling(CO)but how to integrate Training & Event Management with FI.

What functionality are you looking for?

Event Management - How to Use?

Hello,
I need some help with event management. This tab is not available on my Adobe Connect and I am wondering how I can enable it. I need to promote my event with emails, as well as create a custom landing page, which I know can be done since it was something I had available to me in my free trial. It seems I might need to change my role to admin but I am not able to do this. Can anyone help me out with this? I have already spoken with 10 customer service reps and they have not been able to assist me.

Contact your reseller, as they can get you the Events module.
If you don't have a reseller, feel free to PM me or contact me off forum jorma[at]realeyes.com

Books on SAP Event Management

There are 3 books on SAP Event Management out there:
SAP Event Management - SAP's best kept secret...
Title: SAP Event Management - SAP's best kept secret
ISBN: 978-0-9842350-1-8
Author: Kevin Wilson, Author Profile: Amazon
Publisher: Genie Press, Published: 2/5/2010
Book website: Genie Press
Available at: Genie Press, Amazon
SAP Event Management - Das umfassende Handbuch (German)
Title: SAP Event Management - Das umfassende Handbuch, Language: German
ISBN: 978-3836215510
Authors: Berthold Hege, Jens Kappauf, Bernd Lauterbach, Frank Overgoor, Rob Uljee
Publisher: SAP Press, Published: August 2010
Available at: Amazon
Implementing and Configuring SAP Event Management
Title: Implementing and Configuring SAP Event Management
ISBN: 978-1-59229-316-2
Author: Sandeep Pradhan
Publisher: SAP Press, Published: 2010
Book website: SAP Press
Available at: SAP Press

Thanks Kevin.

Event Manager Solution.

Hi Guru's,
What is Event Manager Solution? What exactly we do there? Can you provide me some documentation as my new project involves me to work with event manager solution and SCM. Pls provide me ur insights as this will benifit me to the maximum extent.If you have an documentation pls mail to [email protected]
Thanks in anticipation.
vpk

hi
check this
http://help.sap.com/saphelp_scm50/helpdata/en/e4/bd6c3cf4bc184ce10000000a11405a/frameset.htm

Changing port configuration with Event Manager

Similar Messages

Maybe you are looking for