Cisco 881w guest configuration help

Hello all,
I am looking to figure out how to configure a cisco881w for a guest account. I dont want to use the local database to do so... we have a software called smart pass that handels the guest requests. the radius server dosent use any authentication protocols, all I found out is the authentication port 1814 and accounting port 1813. Because we want to keep the guest wireless users away from our internal network, we want them to authenticate against Smartpass, so that they get the agreement of guest usage.
Has anyone attempted this type of setup?
Thanks

Not at present it is not, the port on the 5406zl that the WLC is connected was setup as a trunk group and All VLAN tagged. When I tried this I lost all connectivity to the WLC. Is there something on the WLC that need changing also?.

Similar Messages

Cisco WLC 2125 configuration help

So in a nutshell, from My computer I can ping all VLANS - everything seems to in workding order.
when telnet to the HP 5406zl core routing switch I can ping all VLANs and other parts of the network
But when logged into the Cisco wireless Lan Controller I cant ping VLAN 108 gateway IP (172.24.156.2 ) from the neighbour switch or other services on this VLAN
for example cant ping the DHCP on this vlan from WLC.
The neighbour switch can ping IP of the management interface created on the WLC
WLC cant ping VLAN 108
WLC can ping all other VLAN 102,104,106
Not sure where the problem is ??
Configure Dynamic Interfaces on the WLC for the Guest and Internal Users - DONE
Create WLANs for the Guest and Internal Users - DONE
Configure the 5406zl Layer 2/3 Switch Port that Connects to the WLC as Trunk Port allowing the relevant vlans i.e. management vlan, vlan 102 and Vlan 108 - DONE
Configure the Switch Port that Connects to the AP to VLAN 102 - DONE
configure virtual interface IP 1.1.1.1 - DONE
Configure the Router for the WLANs - DONE
LAP is registered to the WLC - DONE
WLAN and SSID broadcast - OK

Not at present it is not, the port on the 5406zl that the WLC is connected was setup as a trunk group and All VLAN tagged. When I tried this I lost all connectivity to the WLC. Is there something on the WLC that need changing also?.

Cisco asa 5505 with Router 881w Configuration Help

Hello all,
I'm having trouble setting up a second vlan to route to the internet. I have a Cisco ASA 5505 connected to my ISP(OUTSIDE) and a Cisco 881w (INSIDE) router in the back of my firewall. My vlan 10 with the network 192.168.5.1 255.255.255.0 works with pat, however vlan 15 that is on my 881w router does not route to the internet at all. I can only ping from 192.168.15.15 network to 192.168.5.1 I would like some advice on how can I make this set up work. Attached with this discussion is a picture of my topology.
Thanks in advance.
here are the show runs:
Cisco ASA 5505 show run:
ASA Version 8.3(1)
names
interface Vlan1
no nameif
no security-level
no ip address
interface Vlan5
mac-address xxxx.xxxx.xxxx
nameif OUTSIDE
security-level 0
ip address dhcp setroute
interface Vlan10
nameif INSIDE
security-level 100
ip address 192.168.5.1 255.255.255.0
interface Ethernet0/0
switchport access vlan 5
interface Ethernet0/1
switchport access vlan 10
interface Ethernet0/2
interface Ethernet0/3
shutdown
interface Ethernet0/4
shutdown
interface Ethernet0/5
shutdown
interface Ethernet0/6
shutdown
interface Ethernet0/7
shutdown
ftp mode passive
clock timezone CST -6
clock summer-time CDT recurring
object network INTERNAL_LAN
subnet 192.168.5.0 255.255.255.0
object network PRIVATE_LAN_192
subnet 192.168.15.0 255.255.255.224
description PRIVATE_LAN_192
access-list INSIDE_access_in extended permit ip any any
access-list INSIDE_access_in extended deny ip any any
access-list OUTSIDE_access_in extended permit ip any any
access-list OUTSIDE_access_in extended deny ip any any
pager lines 24
logging enable
mtu OUTSIDE 1500
mtu INSIDE 1500
ip verify reverse-path interface OUTSIDE
ip verify reverse-path interface INSIDE
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
object network INTERNAL_LAN
nat (INSIDE,OUTSIDE) dynamic interface
object network PRIVATE_LAN_192
nat (INSIDE,OUTSIDE) dynamic interface
access-group OUTSIDE_access_in in interface OUTSIDE
access-group INSIDE_access_in in interface INSIDE
route INSIDE 192.168.15.0 255.255.255.224 192.168.5.2 1
dynamic-access-policy-record DfltAccessPolicy
http server enable
dhcpd dns 8.8.8.8 75.75.76.76
dhcpd address 192.168.5.10-192.168.5.100 INSIDE
dhcpd enable INSIDE
Router 881w show run:
Current configuration : 4912 bytes
version 12.4
no ip source-route
ip dhcp excluded-address 192.168.15.1 192.168.15.10
ip dhcp pool PRIVATE_LAN
network 192.168.15.0 255.255.255.224
interface FastEthernet0
switchport trunk allowed vlan 1,15,1002-1005
switchport mode trunk
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface FastEthernet4
ip address 192.168.5.2 255.255.255.0
duplex auto
speed auto
interface wlan-ap0
description Service module interface to manage the embedded AP
no ip address
arp timeout 0
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
interface Vlan1
no ip address
interface Vlan15
ip address 192.168.15.1 255.255.255.224
no ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 FastEthernet4
no ip http server
ip http authentication local
ip http secure-server

The cable modem does not have any configuration. I cant add any to it. Its a cisco dpc3008. From vlan 10 i have no problem to get to the internet with the above configuration. My problem is just vlan 15.

Cisco 881W - ap gui interface problem

We have a new Cisco 881W wireless router;
used the CP Express gui interface to perform initial setup;
router assigned 10.10.10.3 as wireless ap gui interface;
when entering ap gui the entire screen is blank expect for an "enter" button near bottom;
clicking on this button does nothing; "error on page" is indicated on IE8 status;
assigned SSID is not broadcasting

Hi !!
im the same problem , but i fix it
first you must change the IOS version to ap801-k9w7-tar.124-10b.JDA3 ( you can dowload for the cisco web )
after download the image file you putt this command in the ap exec mode:
ap#archive download-sw /overwrite /force-reload tftp://x.x.x.x/ap801-k9w7-tar.124-10b.JDA3.tar
after the files are copied to flash memmory , the routyer boots with the new image ang bug fixed
its is my configuration working:
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Current configuration : 3267 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap
enable secret 5 $1$T0Qk$/wKGmrwqo0WcBbvTapaNb.
no aaa new-model
dot11 ssid CASIO
   vlan 1
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 7 121A04041B04010132222727
crypto pki trustpoint TP-self-signed-4051168682
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-4051168682
revocation-check none
rsakeypair TP-self-signed-4051168682
crypto pki certificate chain TP-self-signed-4051168682
certificate self-signed 01
3082023A 308201A3 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 34303531 31363836 3832301E 170D3131 30383139 31303037
33385A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D34 30353131
36383638 3230819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100B090 26BE5E77 FCB338C0 F54949DB 43EF95C1 61A9C3FA 38AC8BDC 18931195
B1B1A503 65A71B68 8940639A FB6A6D9B 0F327B09 F5C48ECD 89C1B279 9DC6DC98
11E5D014 914200BB 7F29CFD1 1CC5FDF0 F3AFE547 4954E2CA 37FC1CEC 60641871
D9949391 35C958B3 FBA6FBF7 116612FD DFAB9467 478A6E07 0F7B2616 F1204158
EC510203 010001A3 62306030 0F060355 1D130101 FF040530 030101FF 300D0603
551D1104 06300482 02617030 1F060355 1D230418 30168014 1120DB6C BE01CDEE
64A2DB14 FA240B27 D3573B9B 301D0603 551D0E04 16041411 20DB6CBE 01CDEE64
A2DB14FA 240B27D3 573B9B30 0D06092A 864886F7 0D010104 05000381 81003B69
8FC11090 E61D3BC1 D04FBDC5 622E8BC6 EB63B9FA C795BB15 BB05F417 CFC51F09
A8A1971E 7E523203 5A40654D B71623CB A48B193A 101FD1AD 868128E9 91940B71
5CFDDDD4 856B8170 7700C656 A75443DF DBB60F06 67E37A70 69175B84 24AB0380
221AAA1D 3EB80465 FD1C1F49 B75B0F1D BC4A82B2 EB2176F2 27F54894 5E94
quit
username Cisco password 7 106D000A0618
username ivan privilege 15 secret 5 $1$eEHQ$Dc.dDfXJz2fBbPIGhH.zg1
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1 mode ciphers tkip
ssid CASIO
speed basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
station-role root
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router
no ip address
no ip route-cache
interface GigabitEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.10.5 255.255.255.0
no ip route-cache
ip http server
ip http authentication local
ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
no activation-character
line vty 0 4
login local
end
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
now you cant acces to ap web gui
thanks !!!

1941W configuration help needed

Our Deployment Scenario:-
1941W Gigabit Ethernet 0/0 is connected to the PPOE connection of the ISP.
Gigabit Ethernet 0/1 is connected to the wired LAN
I have created 2 wireless radio Cisco_Kamran_BGN which is operating at 2.4 Ghz Devices and Cisco_Kamran_A which is operating at 5Ghz Devices.
I have created 2 VLans for the Wireless.
Vlan 10 for Cisco_Kamran_A        192.168.10.x
Vlan 11 for Cisco _Kamran_BGN   192.168.11.X
The problem is the Wireless users are not getting the IP address from the respective DHCP server which has been configured on the Router.
Can please any from the community help me and show me where I am missing the configuration.
Please find my router & ap configuration below.
Router Configuration
Router#
sh run
Building configuration...
Current configuration : 3022 bytes
! No configuration change since last restart
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
enable secret 5 $1$TdQt$npYeaf/W0kRElcfMggzJ31
no aaa new-model
service-module wlan-ap 0 bootimage autonomous
no ipv6 cef
ip source-route
ip cef
ip dhcp excluded-address 192.168.1.1 192.168.1.50
ip dhcp excluded-address 192.168.10.1 192.168.10.10
ip dhcp excluded-address 192.168.11.1 192.168.11.10
ip dhcp pool DHCP
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 195.229.241.222 213.42.20.20
ip dhcp pool Cisco_Kamran_A
network 192.168.11.0 255.255.255.0
default-router 192.168.11.1
dns-server 195.229.241.222 213.42.20.20
ip dhcp pool Cisco_Kamran_BGN
network 192.168.10.0 255.255.255.0
default-router 192.168.10.1
dns-server 195.225.241.222 213.42.20.20
multilink bundle-name authenticated
crypto pki token default removal timeout 0
license udi pid CISCO1941W-E/K9 sn FCZ1553C1VK
hw-module ism 0
redundancy
bridge irb
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
interface wlan-ap0
description Service module interface to manage the embedded AP
ip unnumbered GigabitEthernet0/0
arp timeout 0
no mop enabled
no mop sysid
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
interface Wlan-GigabitEthernet0/0
description Internal switch interface connecting to the embedded AP
switchport mode trunk
no ip address
interface Vlan1
no ip address
interface Vlan10
ip address 192.168.10.1 255.255.255.0
ip access-group DSL_ACCESSLIST in
ip nat inside
ip virtual-reassembly in
interface Vlan11
ip address 192.168.11.1 255.255.255.0
ip access-group DSL_ACCESSLIST in
ip nat inside
ip virtual-reassembly in
interface Dialer1
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
ppp authentication pap callin
ppp pap sent-username xxxxxx password 0 xxxxxx
ppp ipcp route default
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list DSL_ACCESSLIST interface Dialer1 overload
ip access-list extended DSL_ACCESSLIST
permit ip 192.168.0.0 0.0.255.255 any
control-plane
line con 0
password xxxxxx
login
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line 67
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
password xxxxxx
login
transport input all
scheduler allocate 20000 1000
end
Router#
Router#
Router#
Access Point Configuration
ap#
ap#
ap#
sh run
Building configuration...
Current configuration : 2603 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap
enable secret 5 $1$JxdQ$a2/00bWJuhUKP9QLC94YD/
no aaa new-model
dot11 syslog
dot11 ssid Cisco_Kamran_A
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 7 1045081417161C5A555C7A7B
dot11 ssid Cisco_Kamran_BGN
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 7 020D05561907017015165949
username Cisco password 7 14341B180F0B
bridge irb
interface Dot11Radio0
description 802.11bgn radio
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
broadcast-key change 3600
ssid Cisco_Kamran_BGN
antenna gain 0
station-role root
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface Dot11Radio1
description 802.11a radio
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
ssid Cisco_Kamran_A
antenna gain 0
no dfs band block
channel dfs
station-role root
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface GigabitEthernet0
description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router
no ip address
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface GigabitEthernet0.10
description 802.11a bridge
encapsulation dot1Q 10
no ip route-cache
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface GigabitEthernet0.11
description 802.11bgn bridge
encapsulation dot1Q 11
no ip route-cache
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface BVI1
ip address dhcp client-id GigabitEthernet0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
no activation-character
line vty 0 4
login local
end
ap#
ap#
ap#

Hi Stepehen,
Did the configuration as per your advice but i am getting the below mentioned error which i have highlighted it in red. Please advice what needs to be done.
Home
Re: 1941W configuration help needed
created by Stephen Rodriguez in Getting     Started with Wireless - View the full discussion
conf t
interface     Dot11Radio0
no ssid     Cisco_Kamran_BGN
no encryption mode     ciphers aes-ccm
exit
interface     Dot11Radio1
no encryption mode     ciphers aes-ccm
no ssid     Cisco_Kamran_A
exit
dot11 ssid     Cisco_Kamran_A
vlan 10
dot11 ssid     Cisco_Kamran_BGN
vlan 11
exit
interface     Dot11Radio0
encryption vlan 11     mode ciphers aes
ssid     Cisco_Kamran_BGN
exit
interface     dot11radio0.1
encapsulation     dot1q 1 native
bridge-group 1
interface     dot11radio 0.11
encapsulation     dot1q 11
bridge-group 11
Configuration of     subinterfaces and main interface
within the same bridge     group is not permitted
exit
interface     Dot11Radio1
encryption vlan 10     mode ciphers aes-ccm
ssid     Cisco_Kamran_A
interface     dot11radio1.1
encapsulation     dot1q 1 native
bridge-group 1
interface     dot11radio1.10
encapuslation     dot1q 10
bridge-group 10
Configuration of subinterfaces and main     interface
within the same bridge     group is not permitted
end
wr
Reply to this message by going to Home
Start a new discussion in Getting Started with Wireless at Home

Guest configuration with WLC

i am using WLC 4402 with firmware 5.1 and 1252 Access Point.
i am in trouble to configure guest access with the WLC.
i have configured interface in WLC under CONTROLLER->INTERFACES->GUEST.
WHEN I SELECT THIS INTERFACE AS GUEST IT DOESN'T TAKE IP ADDRESS INFORMATION. IN THIS CASE I HAVE TO UNCHECK GUEST SELECTION BOX.
AND I GOT DYNAMIC INTERFACE WITHOUT IP ADDRESS.
AFTER DOING THIS I CREATE WLAN NAMED GUEST AND ENABLED IT.
i have put guest interface as a ingress interface and management as egress interface and applied web auth successfully but still it is not showing me guest SSID when i try to search it.
help me
plz
thanks

Have you gone through these documents yet?
Wired Guest Access using Cisco WLAN Controllers Configuration Example
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00808ed026.shtml
Guest WLAN and Internal WLAN using WLCs Configuration Example
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008070ba8f.shtml
Hope these will help you.

AAA config on cisco 881w

help configure AAA (Radius server, access list)
There are two devices
An access point and cisco 881w. It is necessary to set up authentication through a radius server.
You can configure detailed how to do this?

Hi,
I guess you are looking for the Local Radius server.
It is mentioned in the following link i gave you above:
881W router sample config:
http://www.cisco.com/en/US/solutions/collateral/ns340/ns517/ns430/ns855/white_paper_c11-492842.html
It mentions the following:
Note that if you use a local RADIUS server, you must add the following configuration to create that server. Add as many users as needed by using the username password command:
radius-server local
nas key 0
username password 0
!!SSID configuration with open EAP authentication and WPA for key-
management!!
dot11 ssid corporate
vlan 10
authentication open eap
authentication key-management wpa optional
Hope this helps.
Regards,
Anisha
P.S.: please mark this thread as answered if you feel your query is resolved. Do rate helpful posts

Cisco ISE Guest Sponsor Portal Isssue

Dear all ,
We have insatalled 5 ise 3315 boxes IOS 1.0.4 in our network where in two of them are admin node , two of policy services and one is mnt node. We are using guest sponsor portal for wirless guest user where in we have integrated WLC 5508 with ise and using weblogin for guest users.
We have created open ssid in wlc and using external redirected url of ise for guest login page.
But when we create any guest user in sponsor login for guest user we faced following issue
1) When guest user gets conected to wirless and login in to guest portal with credential after putting credential then its again redirect to same login page
wihout successful login prompt.
Can we pompt successful login after guest login to guest portal or redirect to any other link like google.com so guest user will gets to know he is able to access internet now
2) We have creted time profile 8hours first login for guest user. When guest user gets connected while putting credential in to guest portal.
But we face issue after approximately every 20 mins guest gets disconnected from internet and guest again gets login page of guest portal and if we put same credential then its working but after approx 20 min interval user get disconnected from internet.
Can anyone help me to resolved above issue regading cisco ise guest sponsor portal
Thanks & Regards
Pranav Gade

Pranav your answers are inline,
1) When guest user gets conected to wirless and login in to guest portal with credential after putting credential then its again redirect to same login page
wihout successful login prompt. When you are using CWA (central web authentication) there is no way we can redirect users using the redirect-url because this will always redirect users for every time they initiate a web request. There is no other coa feature that will remove this condition since they have already been authenticated. Here is a guide that explains the user experience when using central web auth -
http://www.cisco.com/en/US/docs/security/ise/1.1.1/user_guide/ise_guest_pol.html#wp1296954
Can we pompt successful login after guest login to guest portal or redirect to any other link like google.com so guest user will gets to know he is able to access internet now No this is not possible, you can change the verbage and force the AUP to be displayed informing users that they can retry their web request after hitting the accept button.
Here is the documented experience once users go through the guest process -
http://www.cisco.com/en/US/products/ps11640/products_configuration_example09186a0080ba6514.shtml#final
2) We have creted time profile 8hours first login for guest user. When guest user gets connected while putting credential in to guest portal.
But we face issue after approximately every 20 mins guest gets disconnected from internet and guest again gets login page of guest portal and if we put same credential then its working but after approx 20 min interval user get disconnected from internet. Check the advanced timer on your SSID as you may be hitting the session timeout on the WLC. Please disable this option and let the COA feature in ISE expire user sessions on the controller.
Thanks,
Tarik Admani
*Please rate helpful posts*

Cisco 881W no longer broadcasting SSID

We've had a Cisco 881W set up in one of our remote offices for a while and the wireless has been fine. Yesterday I got a call saying that the wireless was no longer working.
I went over and it's true, the SSID is no longer broadcasting. I reloaded the router but it's still the same. I tried to get access to the embedded ap and I get this
RTR#service-module wlan-ap 0 session
% telnet connections not permitted from this terminal
RTR#
Now I've not changed anything on the configuration since it went in and it was working before. Has the embedded ap died? The embedded ap is still showing as a component in show hardware.

There is the wlan-gigbitethernet0 which is the switch interface that connects to the AP. That is showing up/up.
A service module wlan-ap0 status shows
RTR#service-module wlan-ap 0 status
Service Module is Cisco wlan-ap0
Service Module supports session via TTY line 2
Service Module is in Steady state
Service Module reset on error is disabled
Service Module heartbeat-reset is enabled
Getting status from the Service Module, please wait..
Image path = flash:/ap801-k9w7-mx.124-21a.JA1/ap801-k9w7-mx.124-21a.JA1
System uptime = 0 days, 5 hours, 59 minutes, 41 seconds
Line 2 has this
line 2
no activation-character
no exec
transport preferred none
transport input all

CUCM and Jabber guest configuration

Hi Everybody ,
I would like to ask the cucm and jabber guest how configuration, I can't find the document to cisco.

Hi,
As per the link that i shared "In a production environment, Cisco Jabber Guest requires that your Cisco Unified Communications Manager be configured to work with Cisco Expressway.
Cisco Jabber Guest can be pointed directly to Cisco Unified Communications Manager for lab deployments only. You must configure a SIP trunk on Cisco Unified Communications Manager for this deployment. This option is best suited to a lab deployment in which the goal is to familiarize yourself with Cisco Jabber Guest without the additional overhead of configuring Expressway. However, without configuring Expressway, Cisco Jabber Guest is not supported in a production environment."
HTH
Manish

Need configuration help on producing dial tone

Hello Experts,
I have a Cisco 2921 router with VWIC3-2MFT-T1/E1 card. On this card we have T1-CAS digital line connected. We have been provided with a set of DID numbers. We have a requirement where, when we dial a DID, the router should provide a dial tone, and should allow the user to dial to extension numbers. Not sure if this is feasible. If at all possible, will need to some configuration help.
Thanks
Arabinda

Sure it's possible. What's the T1 connected to? The router will offer two-stage dialing (aka dial tone) when the incoming POTS dial-peer does not have the 'direct-inward-dial' command on it. The router will accept any input and search for an outbound dial-peer (or ephone-dn for locally registered DNs) to match. Be careful if the T1 is connected to the PSTN as this is a toll fraud risk. You need to use CoR to reign in what outbound dial-peers are available to it.
Dial Peer Basics:
http://www.cisco.com/en/US/tech/tk652/tk90/technologies_tech_note09186a008010ae1c.shtml
Class of Restrictions:
http://www.cisco.com/en/US/tech/tk652/tk90/technologies_configuration_example09186a008019d649.shtml
Please remember to rate helpful responses and identify helpful or correct answers.

881W AP configuration page blank

When we login to the Access Point configuration page we get a blank page with a single "Enter" button. When we push the button nothing happens.
Wat could be wrong here?
(Tested with IE6 and IE8)
Maxim

I recently bought this new Cisco 881W but without support contract. So if I want to get started with the wireless AP of this 881W I first have to buy a technical support contract to be able to download and install the metioned ap801-k9w7-tar.124-10b.JDA3 file?
This seems very strange to me (first time Cisco user

Cisco WLC5760 Fail and Cisco NAC Guest v2.0

Hello,
I have a problem to use an Cisco WLC5760 v3.3.1SE and an Cisco NAC Guest v2.0.
Can anyone help me to synchronise Cisco WLC5760 v3.3.1SE and Cisco NAC Guest v2.0. ?
Thanks you for help.

Hi Adoncamille,
I have the same problem with my 5760 and NAC Guest Server. Did you fixed the problem?,
Best Regards,
Marco Muñoz

Disabling the unlimited Lifetime option in Cisco WCS Guest User Creation

Is there a way to disable the unlimited Lifetime option in Cisco WCS Guest User Add/Schedule tab.If i make those fields uneditable, it just takes out the option to schedule any meetings in future.Using Cisco WCS version 7.0.220.0.

i'm also searching for an solution to disable the unlimited lifetime button for the Lobby Ambassador.
could it that Cisco introduces this maybe a future release?
couldn't be that there are only few people who are disappointed with this solution.
My Customer is thinking now that cisco isn't the right solution for him.

Multiple ethernet network adaptors + MySQL/php5: configuration help needed

I would be grateful if someone could give me some advice on how to configure multiple ethernet adapters under OS X 10.5.6
I have set up my system to work nicely with two ethernet network adapters, each with its own fixed IP. This bit works just fine. The machine supports two separate servers - a mail server and the OS X Apache2 server. I have configured the mail server to only listen to one of the IPs, and the Apache2 server to listen to the other (via httpd.conf). The system also has MySQL and php5 installed / enabled, and these services are only used by the Apache2 server.
The problem I have is that when I start the machine, initially the php5 system cannot connect reliably to the MySQL database system. The fix I have found is to temporarily make the ethernet adapter connected to the mail server 'inactive'. While this is so, the php5/MySQL connection to Apache2 works. Curiously, once an initial connection between php5 and MySQL has been made, subsequently I can make the mail server's ethernet adapter active again without further problems.
I initially thought this might be due to 'service order' issues - but changing the service order (e.g. putting the Apache adapter 'above' the mail adapter in the service order does not help. The fix only works by making the mail adapter inactive temporarily.
I suspect that there is some configuration change I can make to clarify the setup I have. The MySQL and Apache installations only need to talk to the Apache server - but I am not sure how to record this configuration in the OS X system.
Thanks in advance for any assistance that you can provide.
Message was edited by: Gavin Lawrie

Hi Stepehen,
Did the configuration as per your advice but i am getting the below mentioned error which i have highlighted it in red. Please advice what needs to be done.
Home
Re: 1941W configuration help needed
created by Stephen Rodriguez in Getting     Started with Wireless - View the full discussion
conf t
interface     Dot11Radio0
no ssid     Cisco_Kamran_BGN
no encryption mode     ciphers aes-ccm
exit
interface     Dot11Radio1
no encryption mode     ciphers aes-ccm
no ssid     Cisco_Kamran_A
exit
dot11 ssid     Cisco_Kamran_A
vlan 10
dot11 ssid     Cisco_Kamran_BGN
vlan 11
exit
interface     Dot11Radio0
encryption vlan 11     mode ciphers aes
ssid     Cisco_Kamran_BGN
exit
interface     dot11radio0.1
encapsulation     dot1q 1 native
bridge-group 1
interface     dot11radio 0.11
encapsulation     dot1q 11
bridge-group 11
Configuration of     subinterfaces and main interface
within the same bridge     group is not permitted
exit
interface     Dot11Radio1
encryption vlan 10     mode ciphers aes-ccm
ssid     Cisco_Kamran_A
interface     dot11radio1.1
encapsulation     dot1q 1 native
bridge-group 1
interface     dot11radio1.10
encapuslation     dot1q 10
bridge-group 10
Configuration of subinterfaces and main     interface
within the same bridge     group is not permitted
end
wr
Reply to this message by going to Home
Start a new discussion in Getting Started with Wireless at Home

Cisco 881w guest configuration help

Similar Messages

Maybe you are looking for