Cisco 891FW Router - Web Gui
Hey guys,
Bare with me, as I am Cisco newbie and not too familiar with their setups.
I essentially want to be able to use the web interface of the router to configure VPNs, port forwards, etc. and not use CLIs.
Just got a Cisco 891FW Router for a client and want to pre-setup everything, but I couldn't seem to get into the web interface of the router. After finding out (correct me if I am wrong) that it is disabled by default, so you will have to use console to configure it.
So with the cable console I was provided, I used putty and got into that interface (this is where I lack experience in use). Referring to this guide (http://www.cisco.com/c/en/us/td/docs/ios/12_2/configfun/configuration/guide/ffun_c/fcf005.pdf), I tried to enable the Web GUI of the router.
So the commands I ran are:
Router(config)# ip http server
Router(config)# ip http authentication aaa
Router(config)# aaa authentication login default local
I connected a ethernet cable from one of the LAN ports to my laptop and it got an IP address (192.168.15.100). I opened my web browser and put in http://<router name>, and nothing; even tried 192.168.15.1 as I figured that would be the web interface since I got a .15 address.
Did I miss a step or am I following the wrong guide? I am not too familiar with Cisco routers (beside you basic home/small business ones with the WebGUI enabled by default) so if you guys can show me a guide specific to my model, or give me a step-by-step on how to enable the web interface that would be appreciated.
Thanks for any help
Hi,
I'm a little rusty as I always use the CLI and only ever disable the web interface :), but your config looks a little weird.
Try this:
(config)#ip http server
(config)#ip http authentication local
(config)#username jbenoza privilege 15 secret 0 cisco
(config)#wri
Enter the IP address of the router (which will be the default gateway of the DHCP address you were provided) in the web browser and this will allow you to connect.
If you still experience issues, please post the output of a show run as there may be further configurations necessary.
Similar Messages
-
Enable Web gui on Cisco 2901 ISR running IOS 15...
I have recently purchased a Cisco 2901 Integrated Service Router that is running IOS 15... and need some help activating the WEB GUI Interface. I have read some documentation and have not had any luck. Some detailed instructions for the command line would be great if someone has the time to help.
ThanksHi,
It looks as though there is not a Web GUI available for the 2901. However, Cisco does provide a tool called Cisco Configuration Professional, which provides tools to configure routers. It provides options for configuring many different functions in Cisco routers. You can follow the steps laid out in this article: http://www.cisco.com/c/en/us/td/docs/net_mgmt/cisco_configuration_professional/guides/CiscoCPqsg.html
This gives a great overview of how to install and start using Configuration Professional. I hope this helps, and please feel free to respond with any further questions. I will certainly do my best to answer them!
Garrett -
Unable to Login Cisco Prime Collaboation (10.5.1) Web GUI
Hi all,
I cound not login CPC web GUI with credentials which i have configured during installation. With same credentials i could login to CLI.
I have used "cpc-provisioning-10.5.1-320-small.ova" to install CPC.
Best Regards,
MesutHi Mesut,
What credentials u are using to login in CLI & GUI?
Did u try logging through globaladmin?
http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/collaboration/10-0/quick/start/guide/Cisco_Prime_Collaboration_Quick_Start_Guide_10.html
User Accounts
For Prime Collaboration, you will be required to specify various passwords at different instances. This section is designed to help you specify appropriate passwords in several scenarios that demand your login credentials (applicable for both converged application as well as standalone Prime Collaboration Assurance and Prime Collaboration Provisioning applications).
globaladmin- is a superuser who can access both Prime Collaboration Assurance and Prime Collaboration Provisioning UI.
globaladmin password- specify this password when you configure your virtual appliance for either standalone or converged application. See Configuring the Prime Collaboration Assurance Virtual Appliance and Configuring the Prime Collaboration Provisioning Virtual Appliance. You are also required to specify this password when you login to the UI (see the Password Rules for root user and globaladmin section)
regds,
aman -
831 router....'loading cisco router web setup. please wait'
We just received a used 831 from our other office. I put in http://10.10.10.1 then click continue for the language. It comes to a screen that reads: 'Loading Cisco Router Web Setup. Please Wait...' thats as far as it will go. I'm not sure where to start I'm new to cisco routers. I have read the manual that came w/ it but couldn't find out any information. Your help will be greatly appreciated.
ThanksHello Brandon,
CRWS is a little bit buggy, try SDM instead, which is supposed to be the replacement for CRWS. YOu can download it here:
http://www.cisco.com/pcgi-bin/Software/Tablebuild/doftp.pl?ftpfile=pub/web/sdm/SDM-V231.zip&swtype=FCS
When asked for a user ID, just use anonymous/anonymous, it will allow the download.
If you cannot download, post your email address and I will send you the file.
You could also try another browser, such as Firefox:
http://www.firefox.com
HTH,
GNT -
Cisco 4400 WLC - Accessing web gui remotely
I know how to access the GUI from the service port. However, I am not able to access from Port 0. IPs have all been properly set. We have a management VLAN in our enterprise. I have configured the WLC management interface for an ip on that subnet. Port 0 is connected to a 3560G switch. I have set the switch port to be an access port to the management vlan and I have tried to set the switch port as a trunk, with the native vlan set to the management vlan. I am not able to ping nor access the web GUI remotely via the management vlan. Is this by design?
JeffHi Jeff,
plz try to configure 0 as vlan on managment interface on WLC after configuring native vlan on the switch. if you havent tried it yet.
command - config interface vlan management 0
NOTe - you need to disabl all wlan that r mapped with management interface before doing any changes from CLI.
hope it will solve your prob.
Thanks -
1142N unable to open Web GUI and CMD line options not available
I am currently trying to configure two 1142N APs (AIR-LAP1142N-A-K9) to be stand alone APs. I have followed the PDFs
http://www.cisco.com/en/US/customer/docs/wireless/access_point/12.3_8_JA/configuration/guide/s38frst.html#wp1103248
and
http://www.cisco.com/en/US/customer/docs/wireless/access_point/12.3_2_JA/configuration/guide/s32frst.html#wp1103310
I set up the switch to provide DHCP and confirmed that each AP is indeed assigned an IP address. I can also ping each device. However when trying to browse to the GUI it fails to connect. So I tried to configure it via the CMD line. The enable mode does not give the option to configure interfaces as you would expect in enable mode nor does it give the option to enter global exec. example of the out put below.
AP8843.e178.0ee0>
AP8843.e178.0ee0>enable
Password:
AP8843.e178.0ee0#?
Exec commands:
cd Change current directory
clear Reset functions
clock Manage the system clock
crypto Encryption related commands.
debug Debugging functions (see also 'undebug')
delete Delete a file
dir List files on a filesystem
disable Turn off privileged commands
enable Turn on privileged commands
exit Exit from the EXEC
fsck Fsck a filesystem
help Description of the interactive help system
led LED functions
lock Lock the terminal
login Log in as a particular user
logout Exit from the EXEC
lwapp lwapp exec commands
mkdir Create new directory
monitor Monitoring different system events
more Display the contents of a file
name-connection Name an existing network connection
no Disable debugging functions
ping Send echo messages
pwd Display current working directory
release Release a resource
reload Halt and perform a cold restart
rename Rename a file
renew Renew a resource
rmdir Remove existing directory
send Send a message to other tty lines
set Set system parameter (not config)
show Show running system information
systat Display information about terminal lines
terminal Set terminal line parameters
test Test subsystems, memory, and interfaces
traceroute Trace route to destination
undebug Disable debugging functions (see also 'debug')
upgrade Upgrade software
verify Verify a file
where List active connections
It seems that the IOS on this device does not have the capability to configure the AP as stand alone or that it has been disabled. How do I get into the CMD line to configure the AP for deployment?
Secondly since I could not configure it via the CMD line I attempted to connect to it via the GUI like I said above. This fails. I ran an NMAP to find out what is open and found that nothing but port 23 is open. What is the deal here? Is the web GUI shut off by default? Am I just totally missing something? I think I dies a little inside after this...help please?AP8843.e178.0ee0#sh ver
Cisco IOS Software, C1140 Software (C1140-RCVK9W8-M), Version 12.4(18a)JA, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Fri 21-Nov-08 01:28 by prod_rel_team
ROM: Bootstrap program is C1140 boot loader
BOOTLDR: C1140 Boot Loader (C1140-BOOT-M) Version 12.4(18a)JA3, RELEASE SOFTWARE (fc1)
AP8843.e178.0ee0 uptime is 2 hours, 16 minutes
System returned to ROM by power-on
System image file is "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1142N-A-K9 (PowerPC405ex) processor (revision B0) with 98294K/32768K bytes of memory.
Processor board ID
PowerPC405ex CPU at 586Mhz, revision number 0x147E
Last reset from power-on
LWAPP image version 3.0.51.0
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address:
Part Number :
PCA Assembly Number :
PCA Revision Number : A0
PCB Serial Number :
Top Assembly Part Number :
Top Assembly Serial Number :
Top Revision Number : A0
Product/Model Number : AIR-LAP1142N-A-K9
Configuration register is 0xF -
Is Guest VLAN configurable on the E-series WEB GUI yet
I logged on this board 2 months ago inquiring the availability of the Guest VLAN feature on the WEB GUI of the E-series home router and the answer back then was no.
I saw the Cisco Connect has been updated to work in synch with the WEB GUI and the new firmware has some minor bugs fixed on the Guest VLAN feature. My original:
Is Guest VLAN feature now available to configure on the WEB GUI of the E-series home router?Are your talking about Guest VLAN or Guest WLAN?
Guest WLAN Feature is only available in E4200.In E4200 Router you have an option to configure the Guest WLAN using the WEB Interface. -
Greetings. First, let me start by saying I am an idiot, I know I am an idiot, and I apologize for wasting everyone's time. I have actually RTFM, many RTFMs, in fact, and I still have not found a resolution.
Second, I am trying to set up a RADIUS server in my test network. I have installed ClearBox RADIUS on a Windows 2000 system. I have the following configuration on my Cisco 2611 router:
Using 2297 out of 29688 bytes
! Last configuration change at 17:20:27 PDT Tue May 20 2008
! NVRAM config last updated at 17:20:29 PDT Tue May 20 2008
version 12.1
no service single-slot-reload-enable
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname Tester
logging buffered 10000 debugging
aaa new-model
aaa group server radius RadiusServers
server 172.26.0.2 auth-port 1812 acct-port 1813
aaa authentication login default group RadiusServers local
aaa authentication login localauth local
aaa authentication ppp default if-needed group radius local
aaa authorization exec default group radius local
aaa authorization network default group radius local
aaa accounting delay-start
aaa accounting exec default start-stop group radius
aaa accounting network default start-stop group radius
aaa processes 6
enable secret xxx
username test password xxx
clock timezone PST -8
clock summer-time PDT recurring
ip subnet-zero
no ip domain-lookup
no ip bootp server
interface Loopback0
ip address 192.168.0.1 255.255.255.0
interface Ethernet0/0
description To Main Network
ip address X.X.X.X 255.255.255.128
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
full-duplex
no cdp enable
interface Ethernet0/1
description To Internal Network
ip address 172.26.0.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
load-interval 30
full-duplex
no cdp enable
ip nat pool test X.X.X.X X.X.X.X netmask 255.255.255.128
ip nat inside source list 3 pool test overload
ip nat inside destination list 3 pool test
ip classless
ip route 0.0.0.0 0.0.0.0 X.X.X.X
no ip http server
ip radius source-interface Ethernet0/1
access-list 3 permit 172.26.0.0 0.0.0.255
no cdp run
snmp-server community public RO 15
radius-server host 172.26.0.2 auth-port 1812 acct-port 1813 key secret
radius-server retransmit 3
radius-server key secret
line con 0
password xxx
logging synchronous
line aux 0
line vty 0 4
access-class 10 in
password 7 1234567890
logging synchronous
ntp clock-period 17208108
ntp server 192.43.244.18
end
My RADIUS server is up and responding to requests, but my router does not appear to be forwarding authentication requests to it. In fact, when I log into the router using HyperTerm, it times out, and I end up authenticating locally.
I really don't care whether my Cisco equipment authenticates against the RADIUS server, but I do need to get it set up to authenticate my users so I can track their time online. What have I missed in my router configuration? Why isn't it forwarding user authentication requests to the RADIUS server.
Thank you for any assistance you may be able to provide.I have found that if I am in the middle of composing a response, and I open the thread in another browser window (to refer to it), when I go to submit my response, it doesn't get posted. Perhaps you are running into the same thing.
The command I shared:
aaa authentication enable default group radius local
... was erroneous. The keyword should have been "enable", as you have discovered.
Therefore use:
aaa authentication enable default group radius enable
When I view a Wireshark trace I see the following:
AVP: l=18 t=User-Password(2): Decrypted: "user-PWD\000\000\000\000\000\000\000\000"
Like you, I see the user password appended with the group of \000 grouping's.
Note the word "Decrypted" which confirms that the password entered in Wireshark is a match with that entered on the AAA client (for what that's worth).
I'm not sure if I suggested that this would confirm that the server and client were using the same shared secret. If I did, I miss-spoke. I think we would have to gauge the server's response to the attributes we see passed by the client.
The Wireshark decryption is much more dramatic with TACACS+ because the whole payload is encrypted.
My issue with your PPPoE is that I saw no "interface" on the router that is configured to perform such authentication. I do seem to recall a global authentication command with the PPP keyword perhaps. I have not attempted to do this, and am not sure whether the interfaces in your router will support this method. Perhaps someone else will weigh in with an opinion.
However, there are other mainstream authentication methods that I think you should investigate as well.
You could implement 802.1x on a switch so that a host has to authenticate before it can gain Layer 3 access to the LAN. Depending on the platform, you can download VLAN assignments and ACLs.
I believe the router also supports 802.1x, but that may determine whether a host can get "through" the router. I have not had cause to investigate 802.1x on the router. I may do so in the future to authorize access to IPsec tunnels.
The router is also likely to support Authentication Proxy. This feature intercepts a user's attempt to browse resources on the other side of the router. User specific ACLs can be downloaded to the router (from RADIUS) to control what resources a user can access.
I think you should:
1. Resolve the issue(s) with AAA logins on the router. It'll establish a baseline of functionality, and give you some short term joy.
2. Investigate whether PPPoE support exists on your router's interfaces.
3. Read up on 802.x and Authentication Proxy (docs on Cisco web site).
4. Decide which methods appeals to you.
5. Dive in.
I'd lose the self-deprecation. I don't think it will serve you well. If you're treated badly, move to a newsgroup where the participants display a higher level of emotional maturity. I don't think you will have an issue on the Cisco forums. Others would probably step in.
I'm going to be absent for several days, so if you don't receive any response, it will be for said reason.
Good luck. -
2602e Reset to Defaults Except IP not Work over Web GUI
Hello,
1. Set a Static IP
2. Apply & Save Configuration
3. After Reboot the IP is correct.
Then do Reset to Defaults Except IP in the WEB Gui.
After Reboot the AP loos the static IP and get a DHCP Address.
Reset to Defaults Except IP = Reset to Defaults !
Whats Wrong ?OK, here is:
Writing out the event log to flash:/event.log ...
*Jan 22 17:44:56.675: %SYS-7-NV_BLOCK_INIT: Initialized the geometry of nvram
*Jan 22 17:44:57.547: %SYS-5-RELOAD: Reload requested by on console. Reload Reason: Reload Command.
Write of event.log done
IOS Bootloader - Starting system.
flash is writable
FLASH CHIP: Numonyx Mirrorbit (0089)
Xmodem file system is available.
flashfs[0]: 212 files, 7 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31997952
flashfs[0]: Bytes used: 15058432
flashfs[0]: Bytes available: 16939520
flashfs[0]: flashfs fsck took 23 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: 10:f3:11:c2:2e:3a
Ethernet speed is 1000 Mb - FULL Duplex
Loading "flash:/ap3g2-k9w7-mx.152-4.JB3a/ap3g2-k9w7-mx.152-4.JB3a"...##########################
File "flash:/ap3g2-k9w7-mx.152-4.JB3a/ap3g2-k9w7-mx.152-4.JB3a" uncompressed and installed, entry point: 0x2003000
executing...
Secondary Bootloader - Starting system.
Tide MB - 32MB of flash
Xmodem file system is available.
flashfs[0]: 212 files, 7 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31997952
flashfs[0]: Bytes used: 15058432
flashfs[0]: Bytes available: 16939520
flashfs[0]: flashfs fsck took 14 seconds.
Base Ethernet MAC address: 10:f3:11:c2:2e:3a
Boot CMD: 'boot flash:/ap3g2-k9w7-mx.152-4.JB3a/ap3g2-k9w7-xx.152-4.JB3a;flash:/ap3g2-k9w7-mx.152-4.JB3a/ap3g2-k9w7-mx.152-4.JB3a'
Loading "flash:/ap3g2-k9w7-mx.152-4.JB3a/ap3g2-k9w7-xx.152-4.JB3a"...#######################################
File "flash:/ap3g2-k9w7-mx.152-4.JB3a/ap3g2-k9w7-xx.152-4.JB3a" uncompressed and installed, entry point: 0x1003000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C3600 Software (AP3G2-K9W7-M), Version 15.2(4)JB3a, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Mon 23-Dec-13 08:11 by prod_rel_team
Tide MB - 32MB of flash
Initializing flashfs...
flashfs[3]: 212 files, 7 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 31739904
flashfs[3]: Bytes used: 15058432
flashfs[3]: Bytes available: 16681472
flashfs[3]: flashfs fsck took 12 seconds.
flashfs[3]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 11999232
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 11998208
flashfs[4]: flashfs fsck took 0 seconds.
flashfs[4]: Initialization complete.
Copying radio files from flash: to ram:
Copy in progress...CCCCC
Copy in progress...CCC
Copy in progress...CCCC
Copy in progress...CCCC
Copy in progress...CC
Copy in progress...CCC
Copy in progress...CC
Copy in progress...CCCCC
Uncompressing radio files...
...done Initializing flashfs.
Radio0 present 8764 8000 0 A8000000 A8010000 0
Rate table has 650 entries (20 legacy/224 11n/406 11ac)
POWER TABLE FILENAME = ram:/B2.bin
Radio1 present 8764 8000 0 88000000 88010000 4
POWER TABLE FILENAME = ram:/B5.bin
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-SAP2602E-E-K9 (PowerPC) processor (revision A0) with 204790K/57344K bytes of memory.
Processor board ID FGL1711Z6K6
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 10:F3:11:C2:2E:3A
Part Number : 73-14511-02
PCA Assembly Number : 800-37898-01
PCA Revision Number : A0
PCB Serial Number : FOC17093TXF
Top Assembly Part Number : 800-38357-01
Top Assembly Serial Number : FGL1711Z6K6
Top Revision Number : A0
Product/Model Number : AIR-SAP2602E-E-K9
Press RETURN to get started!
*Mar 1 00:00:16.035: %IFMGR-7-NO_IFINDEX_FILE: Unable to open nvram:/ifIndex-table No such file or directory
*Mar 1 00:00:16.151: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (11)APAVC: WlanPAKs 18174 RadioPaks 17566
*Mar 1 00:00:23.131: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
*Mar 1 00:00:29.443: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
*Mar 1 00:00:29.503: initializing dot11 onplus
*Mar 1 00:00:29.667: not a autoconfig enabled device!!!
*Mar 1 00:00:31.671: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:32.671: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 00:01:18.015: Starting Ethernet promiscuous mode
*Jan 22 17:44:57.000: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Jan 22 17:44:57.000: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Jan 22 17:44:57.007: %CDP_PD-4-POWER_OK: Full power - HIGH_POWER inline power source
*Jan 22 17:44:57.015: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3600 Software (AP3G2-K9W7-M), Version 15.2(4)JB3a, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Mon 23-Dec-13 08:11 by prod_rel_team
*Jan 22 17:44:57.015: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
*Jan 22 17:44:57.999: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Jan 22 17:44:57.999: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Jan 22 17:44:57.999: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to downERROR: Failed to configure ethernet promiscuous mode. Interface Descriptor mismatch
*Jan 22 17:45:01.667: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (0-0)
*Jan 22 17:45:01.667: DPAA Initialization Complete
*Jan 22 17:45:01.667: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Jan 22 17:45:02.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Jan 22 17:45:06.863: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.16.33.216, mask 255.255.254.0, hostname ap -
Configuration doc for 1240AG web GUI
hi! I am using web GUI to configure this AP but can not locate configuration guide for web GUI.
there are plenty of them for CLI
version is 12.4(10b)JDA
Where can I find configuration guide based on web GUI?
any help is appreciated!Release notes:
http://www.cisco.com/en/US/docs/wireless/access_point/ios/release/notes/12_4_10b_JDArn.html
Here is the config guide:
http://www.cisco.com/en/US/docs/wireless/access_point/12.4_10b_JA/configuration/guide/scg12410b.html
That should resolve your question -
EA4500 would not allow web GUI mgmt session any longer?
Hi everyone,
The strangest thing -- EA4500 would not allow web GUI mgmt session any longer?
It worked just fine for 6 moths; now if I try to manage it using the web gui it would authenticate fine but right after correct password is entered it will sit with the little spinning wheel forever:
Remedies that did NOT work:
1. Rebooted several times
2. Flashed firmware using the tool FW_EA4500_2.1.39.145204.SSA.zip
3. Tried several different browsers
4. Same as number 3 above but from another laptop
Otherwise the router's functions are 100% operational; both wireless and hard-wired; works; performance is as expected in terms of speed; port forwarding works; lights work as expected.
So what's left? I really would like to avoid reset to factury configuration as I have ton of settings which I didn't ducoment back in the day when it was installed.
Thanks everyone for your suggestions!Hi bbiandov,
You may disconnect your modem from the router and try to access the user interface again. If you can't access the page still, you may need to reset the router and reconfigure it.
Help, learn and share -
Dear ALL,
what port used RV042 WEB GUI ? port 80?
can we change that port?maybe become port 8080?
because we have another web server use port 80 too.
please give me info.
thanks & regards,1) Port Management > Port Settings page - not displaying correctly.
2) VLAN Management > Interface Settings > Edit page - not displaying correctly.
I did a little experimenting concerning issues 1) and 2) above and found the following:
Issue 1)-After going to the Port Settings page of the web config tool, hit F12-Developer Tools in IE (my version is 32 bit 11.0.9600.17691) and change the document mode to emulate “edge” (in the IE developer tool toolbar). Then refresh the Port Settings page. I was able to make changes and apply.
Issue 2)-After going to the VLAN>Interface Settings page, selecting a port and hitting edit, once again use F12 of IE to change document mode to “edge” THEN click the green arrow in the upper left corner of the IE developer tool to continue. Again I was able to make changes and apply.
This may be a good enough workaround to get by until Cisco issues an update. -
Hi,
I have a Cisco EPC3925 router.
Can I somehow add a static routing rule?
Similarly, the Windows command:
route add 195.199.255.195/32 192.168.0.3
Thanks in advance for your help
F.W.Hi Ferenc,
Thank you for your question. However, this community is for Cisco Small Business Products and the DPC/EPC3925 is not a Cisco Small Business Product.
Your product is an internet service provider (ISP) supported product. In other words you need to contact your ISP or technology reseller that you purchased this from to help you with your question.
http://www.cisco.com/web/consumer/support/modem_DPC3925.html
http://www.cisco.com/web/consumer/support/prod_modems.html
Regards,
Cindy Toy
Cisco Small Business Community Manager
for Cisco Small Business Products
www.cisco.com/go/smallbizsupport
twitter: CiscoSBsupport -
need driver or app for ms life cam 3.0 tried to get one off the internet. cisco wireless router software said malware and virus threat. Is it safe for mac? is this software try to protect my pc or is it A threat to macs to.
There are a number of extremly dubious sites which claim to offer Drivers for common Hardware, but actually are phishing for identies and credit card numbers and candidates to join a bot-net.
Make absolutely certain you load drivers ONLY from the manufacturer's web site. -
WLC Web GUI Certificate type displayed
Hi,
We Converted some APs from IOS to LWAPP and had them successfully Join a WLC.
We have, to date, never bought owned or otherwise possessed an AP which talks LWAPP out of the box.
However the WLC Web GUI says, under the Wireless heading, that AP Certificate Type is "Manufacture Installed" .
Shouldn't it say "Self-Signed" ?
regards, MHThankyou for your reply.
Looking at Cisco document,
"Upgrading Autonomous Cisco Aironet Access Points to Lightweight Mode"
I can see where it confirms what you said about MIC,
"Factory installed certificates are referenced by the term MIC, which is an acronym for Manufacturing
Installed Certificate. Cisco Aironet access points shipped before July 18, 2005, do not have MIC, so
these access points create a self-signed certificate when upgraded to operate in lightweight mode."
Most of this document talks about SSC not MIC and is indisciminate about the age of the AP.
So if I'm converting 1131AG APs bought in 2006 from Autononous to LWAPP am I dealing with MIC not SSC?
Regards, MH
Maybe you are looking for
-
Clearing Difference in Foreign Credits House Bank Account
Dear All, We are facing a problem while clearing a Foreign Credits House Bank Account. While clearing an account through F-03 the system is prompting an entry to be posted in Exchange Difference Gain/Loss Account. Now such an entry was n
-
What is use of asteric sign in oracle
Updat TableA Tout set col3,col4 = (select col3,col4 from TableA Tin where Tin.col1=Tout.col1 and Tin.col2=Tout.col2 and Tin.coln=*'B'* ) where coln=*'A'
-
Since two Months i can't charge my i phone 4s , the issue began in sound , the iphone will be mute or silent alone without touch anything , then the iphone sometimes accept to be charged and sometimes don't accept , finally it don't accept that and i
-
Calendar data not in "Home" library folder
Tried looking for home/library/calendar. In order to back up my lost calenda revents with time machine, I would like to know where those events are stored so I don't have to back up my whole computer. As mentioned in the discussion table there is no
-
I have a new MacBook Pro. I am using firefox version 7.0.1, but my homepage is set to google. Firefox constantly keeps opening new tabs to its own homepage by itself. How can I disable this feature.