Cisco PI Alarm Message

Hello,
I got the following error via Mail from my NCS.
Virtual Domain: ROOT-DOMAIN
NCS has detected one or more alarms of category AP and severity Critical in Virtual Domain ROOT-DOMAIN
for the following items:
1. Message: AP 'AP01' disassociated from Controller '172.x.x.x'.
Anybody know what it means?
Thanks
Sent from Cisco Technical Support iPhone App

Hello,
i got some new error messages:
NCS has detected one or more alarms of category Controller and severity Major in Virtual Domain ROOT-DOMAIN for the following items:
1. Message: Radius server '172.x.x.x'(port 1812) is deactivated on WLAN 'wlan49'.
NCS has detected a change in one or more alarms of category Controller and severity Major in Virtual Domain ROOT-DOMAIN.
The new severity of the following items is Clear:
1. Message: Radius server '172.x.x.x'(port 1812) is activated on WLAN 'wlan49'.
Error an clear message arrive in the same second. I receive this alarm for "wlan48" (18:53 Uhr), "wlan49" (18:50) and "wlan51" (18:55 Uhr).
Devices: WLC HA Cluster 7.4.100.60, PI: 1.3.0.20
The radius server is on the same site as the WLC´s. What could be the reason for these problem? I receive this error and the above discribed after update PI form 1.1.1.24 to 1.3.0.20. Is the new version more sensitiv in this case?
thanks

Similar Messages

Including Interface Description in Cisco PRime Infrastructure Alarm Message

Hi all,
i succesfully configured a Cisco Prime Infrastructure 2.1 applliance to display an alarm and to send me an e-mail when switch uplink ports goes down.
The text displayed in alarm message is :
port 'interface_id' is down on device 'device_ip_address'
I'd like to include in this text also the interface description so the text will display :
port 'interface_id' 'interface_descriprion' is down on device 'device_ip_address'
Is this possible?
Thankyou in advance

Hi,
i followed these steps :
SWITCH SIDE
- configured Prime Infrastructure as snmp-server host;
- enabled snmp-traps for linkup and linkdown events globally;
- disabled snmp-traps for linkup and linkdown on non relevant interfaces using the no snmp trap link-status command
PRIME INFRASTRUCTURE SIDE
- under "Deploy/Monitor Deployment" i deployed template "Interface Health" for all the interested switches
- under "Administration/System Settings/Mail Server Configuration" configured my internal SMTP server to make Prime Infrastructure able to send e-mails
- under "Operate/Alarms & Events" click on "Email Notifications" , then on "Switches and Hubs"
- check the "critical" box , insert the destination e-mail address into the "To" field then click "Save"
- check the "switches and Hubs" box and then click Save
As i know is possible to avoid to configure every single not-interesting port on the switches with "no snmp trap link-status" command (it's a bit annoying when you have tens of switches), using Port Grouping configuration on PI but i tried it without success.
Hope this helps.
Best Regards,

ISE alarm message - HIgh EPM Db usage Replication Stopped

Dear experts,
I have the following alarm messages on my ISE monitoring Dashboard
Has everyone experience the same problem ?
Thanks in advance..
Regards,
Rian

High Memory Utilization -
Cisco ISE system is experiencing high memory utilization.
Check if the system has sufficient resources. Check the actual amount of work on the system for example, number of authentications, profiler activity etc. Add additional server to distribute the load.
High Operations DB Usage-
Cisco ISE monitoring nodes are experiencing higher volume of syslog data than expected.
Check and reduce the purge configuration window for the operations data.

Cisco CDN (Alarm 550001 (SEKeepalive) SE keepalive timed-out )

Dear Cisco Experts,
My systems as below:
CDSM, SR: version 3.2.1
SE1: version 3.2.1
SE2: version 2.6.3
Status (all devices): online (from CDSM: cms connectivity from all devices are OK)
SE1 can work normally, but SE2 doesn't work, Alarm:"SE SE2 keepalive timed-out" from CDSM.
log from SR:
192.168.11.0/24 20 SE2 (Down, Static)
192.168.8.0/24 20 SE1 (Operational, Static) (Load 1%, Device Threshold not reached)
0.0.0.0/0 10 SE1 (Operational, Static) (Load 1%, Device Threshold not reached)
0.0.0.0/0 10 SE2 (Down, Static)
I found infor from cisco about this alarm:
Alarm 550001 (SEKeepalive) SE keepalive timed-out or SE is not reachable.
Explanation Either the SR has not received keepalives from the SE, or the SE is not reachable.
Recommended Action Check the cables connected to the network device and the SE.
I'm sure about network connectivy is OK, problem should be from Version mismatch between SE and SR, Could you help me for this?
Many thanks and rgds.

Hi Long,
The alarm message that you are querying is indicating the keepalive between SR and SE has timed out.
There is UDP based keepalive messages sent from each SE to all SR periodically, by default it is 2 seconds. It is configurable via CDSM GUI. The destination port is 2323. This message has SE load information inside.
To check the keepalive message, you can execute following command on SR
SR# tcpdump udp port 2323
To debug keepalive, you can enable
SR#debug service-router keepalive
Then check service router errorlog under /local1
SR#type-tail errorlog/service_monitor_errorlog.current follow
check any error message popup. quit by Ctrl+C, then undebug all
SR#undebug all
Between 2.6.3 and 3.2.1, there is major difference in the format of packet. We do not recommend you to mix the version in production network. If you are requesting urgent assistance because of the service impact by this alarm, please do contact Cisco TAC support.
Best Regards,
Richard Xie

Ipod Touch 3G no longer plays clock alarm sounds and just pauses and shows alarm messages.

All of a sudden, I am no longer able to hear clock alarm sounds like I used to. Until recently, I was able to just play a music file, set the clock alarm with any sound from the selection while being able to preview the sound before I saved it, and then have it play at the time I set the alarm. Now, whatever music I'm playing just pauses while the alarm goes off and the alarm messages are visble on screen. I went to settings--->general-->sounds and everything is on. What happened here?

Yes, I did. All I needed to do was raise the volume from zero to above using the *actual buttons on the side* of the device instead of just the touch screen volume control. If you try to adjust the volume using *only* the touchscreen volume control, the sound of your music and videos will be affected directly as you desire, BUT if the volume control from the *actual buttons on the side* is completely down, the alarm clock will not sound.
I hope this helps. It may not make sense right off the bat but do give it a try.

Cisco IOS Syslog Messages

Does anyone have a link that shows all the Cisco IOS syslog messages?
Such as this one for the ASA?
http://www.cisco.com/en/US/docs/security/asa/asa80/system/message/syslog.html
Thanks in advance.

This guide should give you what you want.
http://www.cisco.com/en/US/docs/ios/system/messages/guide/consol_smg.html

Prime Infrastructure NCS Alarm Message: CPU: 85 crossed down threshold: 90

Dears,
We have Cisco Prime NCS Ver.2.0 running on plad. Since yesterday the alarm give us severity major message (Message: CPU: 85 crossed down threshold: 90).
Please advice what this problem and how to solve it.
Thanks,

Hi Jeremy,
SNMP traps are shown in the events and alerts section of PI.
SNMP config looks fine. Can you run the SNMP debug (debug snmp packets ) .check the logs and see if the device is actually sending the TRAPS to the PI server.
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors ****

Security Alarm message

Hi.
I'm connected to my family's internet connection (DSL) through my Mac's Airport Extreme wireless card. In the past few days, I've received several alarm-type messages that pop up on the screen when I'm online. Often it kicks me off the internet, and it will take several minutes before I can get a connection again. The message reads thus:
"IP Connection!
192.168.1.101 in use by 00:14:a5:d1:3e:61, DHCP Server 192.168.1.1"
It then requires me to click "OK" before the box will go away.
I don't know what this means except that it relates to my internet connection, so I called my service provider for info and amazingly, they were pretty clueless. They only said that perhaps someone was trying to use use our wireless connection.
If anyone can help shed some light on what this means I would very much appreciate it.
Stevie

Your ISP won't be of much help in solving this problem, since the problem is internal to your own private network.
What seems to be happening is that the IP address being used by your Mac is also being used by another computer on your wireless network. While this could be someone attempting unauthorized access to your wireless LAN, that is a very unlikely possibility if your wireless LAN is password protected (it is, isn't it?).
Unless someone you know has been playing with manual IP address settings on computers that use your LAN, this problem should simply go away if you shut everything down and then restart both your LAN's router as well as all the client computers.

FIne Tuning the Cisco Prime Alarms

HI Expert,
One of our client having Cisco Wireless LAN infrastructure with Cisco Prime. Currently they are getting more alarms (minor) on their environment.
They would like to modify the Alarm pattern / threshold to minimise the Alarms pop-up in prime. Could you please advise me how we can modify this ?
Also do Cisco having any documents for how to fine tune ?
Thank you.
-Ananthan

Hi
Here's the document for the customization of alarms.
Configuring Alarm Severity Levels
A newly generated alarm has a default severity level that you might want to change.
To configure an alarm’s severity level, follow these steps:
Step 1 Choose Administration > System Settings.
Step 2 From the left sidebar menu, choose Severity Configuration.
Step 3 Select the check box of the alarm condition whose severity level that you want to change.
Step 4 From the Configure Security Level drop-down list, choose a severity level, then click Go.
Step 5 Click OK to confirm the changes.
Configuring Alarm Severity Levels
http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2-2/user/guide/pi_ug/alarms.html#pgfId-1054721
- Ashok
Please rate the useful post or mark as correct answer as it will help others looking for similar information

How do we suppress Cisco Prim Alarm ?

Hi Expert,
If there are any way to suppress the repeated alarms in Cisco Prime Infra?
We are using Cisco Prime NCS 2.0 (2.0.0.0.295)
Thank you.
-Ananthan

Hi Ananthan,
AFAIk, there is no way you can suppress the repeated alarms :(
Thanks-
Afroz

Duplicate iCal alarm messages

Since we started synching our machines with Mobile Me I'm now getting multiple alarm notifications from iCal. If I set an notification to email me a reminder about an event on one computer, I get a message from every computer that synchs to Mobile Me... even one from my wife's machine using her email address. We have four computers and an iPad synching to our Mobile Me account, so I get five notifications for every event. Not only that, I get iPhone alarms, possibly because the iPhone is synched with that calendar. So does my wife, and she doesn't want the alarm at all (neither did I want the one that woke me a 4 AM). Is there a way to tame this to get only one email and no iPhone beeps? There must be a simple fix. Either that or Apple has started hiring software designers from Microsoft.

I am having duplicate events on my calendar...EVERYTHING is duplicated.
Fortunately, I don't have alarms set for just everything on the calendar.
It occurs to me that Sync-ing means to do just that. It seems that iCal's definition of Sync-ing is to just just put everything from both devices,(my iPad and my desktop), into a single pile and call it a calendar.If each calendar has the same info, well....it just goes in there twice.
I can't find a "Report Bugs" option in the drop box, either.
As for alarms...can your wife select which calendar she receives alarms from in the settings?
I think that, as long as you have all of your devices synced, you'll get notifications from any device "attached" to your calendar. I think that's the purpose of syncing.
I mean, that is the point of having a sync, so you never miss anything you've placed on the calendar.
So I think that your issue is more about feeling TOO synced.... But I don't know how you'd stop the notifications, aside from turning off the sync on each device that you don't want to receive the info. I am not sure that you can be as selective with how the mobileme service sends your events to your devices so much as you may have to select how you receive those events to each device.
I guess maybe not sending alarms for 4am is a good choice if you don't want to be bugged by that?
Good luck, I am going to see if there is any other thread regarding the Events Multiplicity issue. I also get these VAST duplications of contacts in my contact list and I don't understand that one, either.

Cisco AnyConnect Client Message

What kind of message will the user get when you exceed the SSL licenses.

Hi,
716023
Error Message %ASA-4-716023: Group name User user Session could not be established:
session limit of maximum_sessions reached.
Explanation The user session cannot be established because the current number of sessions exceeds the maximum session load.
Recommended Action Increase the configured limit, if possible, to create a load-balanced cluster.
http://www.cisco.com/en/US/docs/security/asa/asa70/system/message/logmsgs.html#wp2290383
This syslog is generated when a new user comes after the license limit has been reached. So if the license is for 50 users, the 51st simultaneous WebVPN/SSL user will cause the syslog below to be generated.
Regards,
Arul
** Please rate if it helps **

Cisco works error messages

Posted by: alphaomegait - Aug 15, 2005, 7:00am PST
I get messages this, InCharge Domain : DFM Clear: Router FALSE 172.16.1.17 PerformanceException - System is experiencing Port or Interface performance problems.
all day long from Cisco Works.
I have not been able to find anything in technical support on the Cisco site to help with this. Can anyone give me a push in the right direction?
Thanks up front.

I think you have QOS setup on the interface it is possible that this is causing the drops and to rule it out we should try removing "service-policy output llq " from the interface and see if the drops still increment.

Nokia N78 - Date, Alarm, Messages issue after upda...

Hi all,
After software update of my Nokia N78 I retrieve many problems;
please see the list below:
1) Data change suddenly
for example... 26 April ... to 8 May
I noticed that this issue happens often during the week-end.
2) Alarm doesn't work for the daily scheduling
For example:
Scheduled alarm at 17:00 everyday.
sometime happen that the next day alarm doesn't start !!!
3) Alarm don't turn on the phone.
Like the point 2, but in this case often the phone doesn't wake up me !
4) The sort of SMS message.
happened that 5/6 old sms was on top list (sorted by date)
I delete this messages in order to fix this issue.
Please help,
Thanks for your support.
//Luca

Hi !
About point #4, yes, I know ... thanks anyway.
I have a great news for Nokia guys. I deleted all jobs alarm... I mean, I'm not using N78 alarms, and the date issue seem solved !
Unfortunately this is only a workaround, I'm using the alarm of my great N73
I'm an Analyst/Programmer Senior... Nokia, please, check your alarm application that most probably caused too much problem.
Thanks.
//Luca
PS
I found many fault on this SW release; related to the background light, phone keypad lock, keys that seem locked... etc etc... this is the worst update released.

Cisco MARS Syslog messages

/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman";
mso-ansi-language:#0400;
mso-fareast-language:#0400;
mso-bidi-language:#0400;}
Hi,
I've recently noticed that ALL the syslog messages that are sent to our Cisco MARS device are then being sent to our syslog server. Besides the messages from our MARS device, the syslog server also gets the original syslog messages from our ASA and PIX firewalls (which, of course, also send to our MARS device). I would like to have MARS send syslog messages to the syslog server that pertain only to changes/events happening directly to the MARS device. Can anyone help me with this?
Thanks in advance!

Kerry;
To have CS-MARS specific incidents forward to your syslog server, you will most likely want to add an action to generate a syslog for the CS-MARS-specific inspection rules. These rules can be found by navigatng to:
RULES>Inspection Rules
from the Group: drop-down choose "System: CS-MARS Issues"
You can then edit the Action: section for the specific rules (one at a time) to add a syslog action. Specifics are outlined here:
http://www.cisco.com/en/US/docs/security/security_management/cs-mars/6.0/user/guide/combo/alerts.html
Scott

Cisco PI Alarm Message

Similar Messages

Maybe you are looking for