Colors more vibrant in Editor

I took some shots with my Father's Nikon D90 and noticed they appeaed dull.  I opened them in the editor, and they looked better without any changes.  Why would this be?  Could it be the color profile he had his camera set to?  I know my camera is set to sRGB and his is AdobeRGB.

Jason,
This is a known bug in the PSE 6/7 Organizer.  It considers photos produced by cameras set to Adobe RGB to be untagged with a color profile.  This causes it to show their colors incorrectly.

Similar Messages

  • Label colors are more vibrant when you switch to column view

    Mayby I am too picky but I noticed that *label colors are more vibrant when you switch to column view*. I guess label colors should always look the same on matter what view you are on.

    ThisisGrey,
    You can also by choose a different color profile in System Preferences...>Displays>Color>Display Profile: Uncheck "Show profiles for this display only," and experiment with a different profile. I personally had the most success with using the "Calibrate..." selection and creating a user calibrated profile for my screen.
    ;~)

  • How to color more than one cell in an ALV line ???

    Hi SDN community,
    I have the following problem:
    I display an internal table with the 'REUSE_ALV_GRID_DISPLAY' function and want to color two cells, not only one cell.
    Coloring one cell is no problem with...
    cell_color1 TYPE lvc_t_scol, " cell color
    DATA  gs_cellcolor    TYPE          lvc_s_scol. " to color a cell
    gs_cellcolor-fname = 'TNAME'.
    gs_cellcolor-color-col = '6'.
    gs_cellcolor-color-int = '1'.
    gs_cellcolor-color-inv = '0'.
    LOOP AT it_result.
      IF it_result-trend EQ 'fast-growing'.
        APPEND gs_cellcolor TO it_result-cell_color1.
        IF sy-subrc EQ 0.
          MODIFY it_result.
        ENDIF.
      ENDIF.
    ENDLOOP.
    and
    ls_layout-coltab_fieldname = 'CELL_COLOR1'.
    , the last one is in the layout building form.
    My problem is that in
    ls_layout-coltab_fieldname = 'CELL_COLOR1'.
    , I can only type in ONE fieldname, but I would like to color more than one field/cell, you got my problem?
    Thank you very much,
    Marius

    I'm pretty sure that the color would be controlled by what records are appended to the CELL_COLOR1 table inside IT_RESULT. . So move the code inside the IF statement, and add addition logic.
    LOOP AT it_result.
      IF it_result-trend EQ 'fast-growing'.
       gs_cellcolor-fname = 'TNAME'.
       gs_cellcolor-color-col = '6'.
       gs_cellcolor-color-int = '1'.
       gs_cellcolor-color-inv = '0'.
        APPEND gs_cellcolor TO it_result-cell_color1.
        IF sy-subrc EQ 0.
          MODIFY it_result.
        ENDIF.
    else.
       gs_cellcolor-fname = 'OTHER_FIELD'.
       gs_cellcolor-color-col = '5'.
       gs_cellcolor-color-int = '1'.
       gs_cellcolor-color-inv = '0'.
        APPEND gs_cellcolor TO it_result-cell_color1.
        IF sy-subrc EQ 0.
          MODIFY it_result.
        ENDIF.
      ENDIF.
    ENDLOOP.
    Regards,
    Rich Heilman

  • Making colors less vibrant

    I am using the rgb color mode and want to make some colors less vibrant. In Photoshop I might desaturate with the sponge tool. What are some of the ways I can do this in cs5?'
    Thank you.

    Desaturating a color means "dirtying" it with its opposite color. In subtractive process (CMYK mode) adding the opposite color grays and darkens the result. In additive process (RGB mode) adding the opposite color grays and lightens the result.
    So for example: Suppose the color you want to desaturate in RGB is yellow. If it's fully yellow, that means R and G are maxed out at 255. Adding B will desaturate it, but will also move it toward white, so as it becomes desatuarted, it also becomes tinted. To compensate, reduce R and G together. The result will be a "grayer yellow" or a "yellowish gray." If the "yellowish gray" tends toward greenish, reduce G slightly relative to the R.
    Whether you do this in the Color palette sliders, the Edit>Edit Colors>Adjust Color Balance dialog, the Hue, Saturation, and Brightness sliders in Edit>Edit Colors>Recolor Artwork dialog, the Intensity slider of the Edit>Edit Colors>Saturate dialog, or by dragging the marker in the Color Picker leftward, you are doing the same thing.
    JET

  • How to get keywords colored in the abap editor

    How do i get the syntax coloring done in abap editor? Is it possible to get the different colors for different keywords in abap editor?

    Hello,
    There is no option for colour.But you can change the key words to upper case.
    For that first go to Utilities->Settings->ABAP EDITOR TAB->PRETTY PRINTER TAB.
    Now u can check INDENT and upper or lower case depending on your requirements.This is for pretty printer settings.
    Come back to your code and click on pretty printer and the keywords are changed to upper-case.
    Regards,
    Beejal
    **Reward if this helps

  • The colors appear more vibrant and redder ONLY on Photoshop

    Hello! For a long while I've had a problem with my Photoshop CS5.
    I had bought Photoshop CS5 and using it on two computers, the older one I usually use more often, it works about perfectly. But on my working laptop my Photoshop shows the colors
    differently:
    As you can see, how the colors should look like is on the right, how Photoshop twists the colors on the left.
    However, once I save the picture, the colors looks like they should (on the right) but not seeing them correctly when editing and manipulating the picture, causes a lot of problems for me and I have no idea how to fix it. It's RBG (At the moment for the web, but when actually working, then with CMYK).
    I've tried many different color settings and God knows what and nothing seems to work.

    here, the bottom image has a moderate saturation boost
    but you don't include the Doc Profile in the middle image
    (and i don't know what app that is, if it is color-managed, if it actually CONVERTING to the Monitor Profile)
    and you are using the sRGB targets (not the WhackedRGB target)
    moreover, your uploaded image (yOznPEp.png) doesn't contain an embedded profile, so it's anyone's guess what you are seeing
    but i captured the original sRGB target above yours
    i guess your middle image is unmanaged or not fully managed because my 10/10/10 black wedge is darker in your "correct" middle version
    if Photoshop is not displaying proper saturation with the settings I recommended, then your monitor profile is off
    there is a ton of search hits on how to calibrate and setup a window's monitor for photoshop
    at this point i don't know what else to add except to start slugging it out...

  • No more vibrant color for finder - Finder has lost RGB capability

    I try changing the profiles in both system prefs and in adobe products; the funny thing is, I get vibrant colors in photoshop, but the same image when seen through the finder is dull and sapped of vibrancy. This is most visible in the reds, which aren't nearly as red as they used to be.
    It seems that the Finder and Mac OS 10.4.9 has lost the full range of this monitor's (and MBP's) color capability.
    Any idea where I can look in the system prefs to reverse whatever changes I made?
    Other note: this affects quicktime as well, so all trailers I see are dull and sapped.

    Run /Utilities/ColorSync Utility and 'repair profiles' ?

  • Label colors more dim now in 7.2.2?

    I noticed when I lay a track in the timeline now with version 7.2.2 it is much darker and more dim than in 7.2.1. See picture attached.
    I thought this could have been a new feature but I went into the preference pane and the preference pane label section has the same bright colors as in 7.2.1. I even screen captured the preference pane colors and the timeline colors in version 7.2.2, and they are way off. Timeline is much darker and more dim tehn selected preference color.
    Not a giant deal, but its annoying and kind of distarcting. Is anyone else noticing this?

    Hi xstimux,
    Sorry you don't like the muted appearance of clips in the Premiere Pro CC (7.2.2)  I have been talking with engineering about this, so they are aware of the issue. Please file a bug report here: http://adobe.ly/ReportBug. That would help a lot.
    Thanks,
    Kevin

  • Colors less vibrant in Aperture 3 - Why?

    I am using Lion 10.7.2 on an iMac 27" 2.7 Core i5 with the latest version of Aperture 3 as well as Photoshop CS5 -- both programs, as well as my monitor, are set to Adobe RGB (1998). My camera, Sony NEX-3 ARW is also set to shoot in the Adobe RGB (1998) color space. Here's my question:
    When exporting a photo from Aperture 3 as a TIFF (8-bit) in Adobe RGB (1998) space and working on the photo in Photoshop, upon importing back into Aperture (saved the file as TIFF, not compressed in PS), the resulting reds are less vibrant. I am seeing this with all colors approaching neon; this is simply one example.
    In another scenario, I imported the raw file directly into photoshop first, did my corrections, and then imported the exported TIFF directly into Aperture. The resulting file is again slightly less vibrant, with the most immediate observation noticed in the neon sign. This problem does not exist for Lightroom 3.
    Adobe Photoshop CS5 exported file:
    File as appears (and as appears if exported) within Aperture 3, noting the neon is less vibrant:
    Why are colors overall less vibrant in Aperture? Is there a configuration issue on my system, or is there a known issue with Aperture? This is not my first time running into color problems with Aperture -- and for my work I need colors to always be spot on.

    Technically, you should only need to verify that you have at least the RAW Compatibility Update 3.6:
    http://support.apple.com/kb/DL1357
    Current version is 3.7 which can be found here:
    http://support.apple.com/kb/DL1386
    Note - I assume that the 3.7 would include 3.6, but am not sure.
    If you already have the correct RAW support for OS X and are importing new images into a new or trial library, you might try running the 'Repair Database' option found here:
    http://support.apple.com/kb/HT3805
    Good luck.

  • Not sure how to match color more closely...use Pantone?

    HI,
    I've done everything possible to get a certainly red color I want in my ID manuscript, from setting color profiles, snyching across applications, monitor calibration, soft-proofing etc.etc etc. What I see on my monitor with the publishers profiles is NOT what I'm getting on my printer (R1900). I guess that's to be expected.
    The publisher has it's own CMYK profile for their printer so i can't use theirs. There are so many different ways to configure printer management from letting ID manage color, using various Epson settings....all this stuff. Even if I get the color right on my printer, that doesn't mean it'll match the publishers, so why even try to get it right on my printer?
    Actually, my document may even print fine with the publishers. Not being able to have more reassurance of the publishers outcome leaves me queasy! But I guess I have to play my hand.
    So is the only way to know is wait for the hard copy? what about using Pantone? I don't know anything about that, but aren't they for spot colors, or at least I could find something closer that way. If there is a color I like, use those numbers rather than the ones I am.
    Ideas?

    Color management is an attempt to put into play .icc color profiles.  This starts in your application's color settings.  But, working with your print vendor is the best policy in preparing your files and getting what you want consistently.  The Epson R1900 is a photographic printer.  It is not an inkjet proofing device like an Epson Stylus Pro 3880 with a Colorburst RIP.  I sense that, because the R1900 is not backed up with a RIP, you'd benefit from "Let InDesign determine color".  However, the print driver is responsible for interpreting the information supplied from the application in an attempt to convert that info to an actual print.  The challenge for you and your applications, along with your hardware limitations, is to give you a reasonable "red" that you are looking for.  In short, you would benefit from assigning a Pantone Spot color for the specific Red you are looking for.  The only problem is getting that Red to print on your R1900.  And, the only way to get that to happen is using CMYK equivalents which you have been wrestling with.  In a RIP ( Raster Image Processor ) scenario, you would use the printer's profile in the Print setup dialogs.  Let's assume they are using "SWOP Coated v2 Sheetfed".  You would assign that profile in your application's Color Settings under CMYK Workspace.  Then, in your "Print" dialog, you'd set the same profile in the CMYK print space.  But, in a RIP scenario, you'd let the RIP determine color rather than the application.  That's the value of a RIP over a photographic printer where color matching is not a priority.  It sounds like you'd benefit using a Pantone Spot.  If you decided to use a Pantone Spot Red in your document, you would need the RIP and Proffer to produce an accurate color matched conversion in the Print process.  With your current setup you will get mixed results from your print vendor.  In any case, at a minimum, you should get a contract proof before you approve the project for press.  This will give you an opportunity to adjust the CMYK equivalents or finalize a decision to go Pantone Spot before the job is ultimately printed.  Now, again, a Postscipt Level 3 RIP matched up to a professional printer/proofer will convert your file's assigned Pantone "Red" Spot color and, in the case of the Epson Stylus Pro 3880, the printer will use it's 8 internal ink sets to produce a relatively close match to your Spot color. 
    "I've done everything possible to get a certainly red color I want in my ID manuscript, from setting color profiles, snyching across applications, monitor calibration, soft-proofing etc.etc etc. What I see on my monitor with the publishers profiles is NOT what I'm getting on my printer (R1900). I guess that's to be expected."
    Yes.  Get a hardcopy proof instead of relying on the R1900.
    "The publisher has it's own CMYK profile for their printer so i can't use theirs. There are so many different ways to configure printer management from letting ID manage color, using various Epson settings....all this stuff. Even if I get the color right on my printer, that doesn't mean it'll match the publishers, so why even try to get it right on my printer?"
    It would help, if you continue to do this type of work, to get a desktop proofer like the one I've mentioned in my post.  You want to "try" to get color matched output so that you are communicating what it is you want before getting to the printer, especially if you have an internal approval process you have to go through.
    "Actually, my document may even print fine with the publishers. Not being able to have more reassurance of the publishers outcome leaves me queasy! But I guess I have to play my hand."
    Not necessarily.  Get the proof.  You do not want 200,000 copies of your manuscript floating around out there with a rose pink instead of a flaming red.
    "So is the only way to know is wait for the hard copy? what about using Pantone? I don't know anything about that, but aren't they for spot colors, or at least I could find something closer that way. If there is a color I like, use those numbers rather than the ones I am."
    Yes.  A Pantone Spot color is actually a very smart decision.  And your InDesign document must be setup using that Spot color, not CMYK.  For instance, let's say you settle on Pantone 206C for the cover and Pantone 206U for the uncoated text pages ( if any ).  It's a simple 2-color job.  Black + Pantone 206.  If you want to print the file on your R1900, then you will convert a swatch using 0%C, 100%M, 30%Y, 3%K in a COPY of your Spot Color file.  Send the Pantone Spot Color file to the publisher and keep the COPY in your folder for reference if need be.
    This is my recommendation and I know it will work for you.  Should the publisher insist on using a CMYK color mix, let them do it and supply you with a hardcopy proof before it goes to press.  This is avery important no matter what you decide.  The proof is very important part of the entire process.

  • New AP3 Version Has Muted Colors when Using External Editor

    Hi All,
    I'm having a frustrating problem. I just noticed that files that I've edited using an external editor (PS5) come back to Aperture with significantly dulled colors. At first I thought it was something that PS was doing. Then, I realized that this was happening to the new versions created by Aperture even before the external editor was completely launched.
    Right when you select "edit with Adobe Photoshop CS5.app" Aperture creates a new version - right then I can see the colors being dulled/muted. I don't for the life of me know how to avoid this from happening.
    My export settings are:
    - 16 bit TIFF
    - DPI: 300
    - External editor color space: Adobe RGB (1998)
    Any help in this would be greatly appreciated.

    I'm taking a look now. It's perplexing (to say the least).
    There is definitely a shift in the created-for-external-editor Version (I'm seeing the same color shift, almost exclusively in the middle- and high-tone cyans, but not quite to the same degree as you). I using my usual settings of 16-bit and "No Profile Selected".
    Although the shifted version shows in Aperture, it does not show in PS-CS5. In other words, the shift is somehow removed when the file is opening in PS. When the file is closed in PS, the shifted version remains in Aperture.
    The histogram is very different for the Versions in Aperture.
    The color values shown in the Loupe and in the color meter (which shows in the Info Pane at the top of the Adjustments tab of the Inspector) are +the same+ for the Versions, though the histograms are different and the images are dissimilar.
    I am seeing -- as best I can tell; it's clearly time to take notes -- inconsistent behavior. Sometimes a shifted Preview will not have a shifted full view. When I send a previously edited in PS Version back to PS, sometimes the shift disappears.
    If I have the time later I'll make a chart. I can confirm that something is amiss. I don't edit that many images in PS, but I still do so regularly, and I have never noticed this before. (My images are in general neither saturated nor blue, so it is possible that there has been nothing to notice in those images. I have some very blue JPGs which I may try.) My hunch, though, it that this will end up being traced to something in the RAW conversion done to captures made with this camera.
    *Anyone have any underwater RAW captures made with a camera other than a Nikon?*
    Message was edited by: Kirby Krieger

  • BeX-Analyzer - color more levels of hierarchy

    Hi,
    i have a hierarchie with 10 levels and i would like to give each level a different color. Using Analyzer i am only able to set different colors for the first 4 levels. Excel offers the following style sheets for this:
    SAPBEXHLevel0
    SAPBEXHLevel1
    SAPBEXHLevel2
    SAPBEXHLevel3
    Is it possible to have more style sheets like:
    SAPBEXHLevel4
    SAPBEXHLevel5
    Thanks,
    Holger

    well, defining my own style sheet wouldn´t help much, because the problem is that BeX Analyzer marks all hierarchy levels bigger than 4 with SAPBEXHLevel3. If i define a style sheet for SAPBEXHLevel4 this wouldn´t work, because the elements of hierarchy level 5 are still marked with SAPBEXHLevel3. Somehow i need to tell BeX Analyzer to mark level 5 elements with style sheet SAPBEXHLevel4, level 6 elements with SAPBEXHLevel5 etc...i guess this is done somewhere in the SAPBEX-Add-In?

  • Can I send just the color file to my editor without sending the sequence

    I am coloring a trailer and I am new to color. What I want to do is grade my sequence that I media managed from my editor and then save it and send my editor just the color info to him so he can render it on his system.
    I'm trying to avoid media managing it again and dropping off my drive to him.

    You could try to simply send the colorproj. Have your editor open the Media Managed version that you were working with. There may be some path reconnecting to do, or not.
    Or they could create a new project, as long as it is identical in every way, then an "Import Color Corrections" from your session will apply all your grades to that project. Be aware that there may be some aspects of the project that do not travel with that container folder -- User Shapes, plugins, etc., that otherwise reside in the User/Library/Application Support/COLOR folder.
    I've often thought this might be an interesting business model, except for the fact that not all GPUs render the export image exactly alike. So, keep that in mind, too.
    jPo

  • Why is everything on screen lighter in color - more grayish.

    Since loading Mavericks, all content on the screen seems to have become much lighter in color. The blacks have become dark gray and the grays are almost too bright to understand/read. Text on Numbers and Keynote are now so tough to read in thier current gray tone.
    How can I make the colors darker. I am using a 2013 Mac Mini and two Planar 27" screens.
    Thanks.

    do your monitors have an option for brighteness and contrast internally?
    to make changes through the os, go to spotlight (hit cmd+spacebar) and type in "colorsync utility" and then enter.
    use this utility to create a profile and then choose the same profile for your other monitor.

  • How can I get the percentage of the image color more faster?

    I tried the command of ColorSampler/ColorSamplers.
    but , sampling speed is very slow.
    So, the script run sampling for 2000x1000 pixels image , then it hangs for five minutes over.
    Do you know the method that can be processed early?
    Sample Script:
        var myDoc = app.activeDocument;
        var lighterSamples=0; // number of lighter pixels
        var darkerSamples=0; // number of darker pixels
        var docWidth = myDoc.width;
        var docHeight = myDoc.height;
        app.activeDocument.colorSamplers.removeAll();
        var pixelLoc = [UnitValue(0) , UnitValue(0)];
        var myColorSampler = app.activeDocument.colorSamplers.add(pixelLoc);
        for(xPos = 0 ; xPos < docWidth ; xPos++){
            for(yPos = 0; yPos < docHeight; yPos++){
                var myColor = myColorSampler.color;
                if(myColor.rgb.red>125){
                     lighterSamples++;
                }else{
                     blackSamples++;
                pixelLoc[0] = xPos;
                pixelLoc[1] = yPos;     
                myColorSampler.move(pixelLoc);
        alert("number of lighter px="+lighterSamples+" / number of darker px="+darkerSamples);
    Thanks.
    Nakamori

    A variation of this thread might help.
    http://forums.adobe.com/thread/834970?tstart=0
    If you saved your document as an eight bit RGB RAW file you could use this code...
    File.prototype.readByte = function() {//aka unsigned byte
         return this.read(1).charCodeAt(0);
    var rawFile = File.openDialog("Please select Raw Image");
    rawFile.encoding = 'BINARY';
    rawFile.open('r');
    var whiteSamples = 0;
    var blackSamples = 0;
    var Total = rawFile.length/3;
    while(!rawFile.eof){
         var R = rawFile.readByte();
         if(R > 125){
             whiteSamples++;
             }else{
                 blackSamples++;
         var G = rawFile.readByte();
         var B = rawFile.readByte();
    rawFile.close();
    alert("Total pixels = "+ Total + " White Samples = " +whiteSamples + " Black Samples = " + blackSamples);

Maybe you are looking for