Configuring westell 6200 and airport

I'm new to this, so apologies...
I had to replace my AT&T Motorola modem recently. AT&T sent me a Westell(netgear) 6200 and it will not connect to anything when connected to my AirPort express. My Airport is broadcasting, but the "disconnected" alert comes on when I've plugged the Ethernet cable into the AirPort.
The Westell works, as I can connect directly. I've tried everything I know how to do - the AirPort is in bridge mode, etc.
What I've gleaned from AT&T's forums is that the Westell is a modem and router, but beyond that, nothing their "experts" suggest works.
Can anyone help?

There are different setups. What is your goal for the Airport Express?

Similar Messages

Configuring a Westell WireSpeed and AirPort Extreme

Dear Group,
I am having no luck setting up a Westell WireSpeed model B90-220030 dsl modem with the AirPort Extreme. My ISP is AT&T FastAccess DSL 3.0 (previously BellSouth).
I read in dslreports.com that the Westell should be changed to a connection type of Bridged instead of it's default setting of PPPoE. This way the Extreme can do the connection through PPPoE, and also perform the DHCP and NAT tasks.
I am able to set the Westell modem to Bridged mode, and I'm able to set the Extreme to PPPoE with my userid and password. I power down and re-start, and everything goes great but for only an hour or less.
My wireless card in my laptop picks up the connection, and I can connect to the internet, but in a matter of an hour or sometimes less, the internet connection drops.
I don't have any problems with internet connectivty if I set the Westell back to PPPoE connection type, and set the Extreme to act like a bridge.
Can anyone tell me which configuration is preferable? Has anyone experienced this same issue when trying to configure their dsl modem to Bridged, and the Extreme to do the connection and DHCP?
Thank you,
Frank

Dear Group,
I've corrected the problem of the Internet dropoff. My Westell Modem was defective, and replaced.
Does anyone know the advantages/disadvantages of setting up the DSL modem as bridged with the AirPort Extreme doing the PPPoE connection?
Thanks,
Frank

How to configure traveling MacBook and airport express

Here is the probelm I am interested in getting help with
I frequently travel with my family with Mac Books and an airport express. When we are at a hotel we dont want to pay for 5 internet connections at the daily rate. So if the hotel has an ethernet wire its easy, I plug in the ethernet wire to the airport express and build my own network. This typically works. The problem comes when the hotel has a wireless network. How can I configure the airport express so that I can create a new wireless network routing the traffic through the single wireless connection that the hotel gives me? If this cant be done with an airport express is there another router it can be done with?
Thanks for any help/advice.

You can setup your Airport Express (AX) as a wireless client connecting to the hotel wireless network. Connect the ethernet port on the AX to your Mac's ethernet port for internet access. Go to System Preferences/Sharing tab, enable internet sharing after configuring "Share your connection from Ethernet" and "To computers using AirPort". Your laptop will act as an access point for your other computers. You may not get blazing speed from the internet since you are splitting the bandwidth, however, this is the lowest cost solution for your dilemma. Remember to set your wireless security before you start sharing your connection or you may have other "guests" connecting to your mini network.

Verizon DSL, Westell 6100 modem/router, and Airport Extreme

Useful info so you won't have to go through what I did.
Verizon ISP using the Westell 6100 modem/router & Airport Extreme.
The Westell 6100 was configured during installation as a modem and router with a direct connection to the Mac. You can actually connect Airport Extreme at this point with an ethernet connection to the Westell and it will work, but you can't do any of the sharing things (remote login, personal web sharing, etc.) To do those things the Westell needs to be in the Bridge mode. In a nutshell, you have to edit the Westell's VC configuration to establish Bridge mode, and disable its DHCP server. Then you have to set up the Airport to connect using PPPoE using the Account Name and Password from Verizon.
1. With the Westell connected directly to the Mac, access the device at 192.168.1.1.
a. Under VC Configuration the first of seven configurations should already be enabled as VPI 0, VCI 35 using PPPoE. Edit that one and change it to Bridge mode.
b. Under DHCP configuration, disable the DHCP server. You can also do this under the Private LAN Configuration page. If at the latter, do not attempt to disable the Private LAN (it won't let you anyway). Verizon tech support kept insisting I had to disable the Private LAN, which caused a great amount of anguish!
c. Before leaving 192.168.1.1 (you won't be able to access it again once the Airport is connected and configured) make sure you know your ISP account name and password. This was assigned during my setup procedure with Verizon, a random selection of letters and numbers.
2. Now hook up the Airport WAN to the Westell's ethernet port and the Mac to the Airport LAN. Fire up Airport Admin Utility.
a. Under the Internet tab, select Connect Using PPPoE.
b. Configure PPPoE using the Verizon Account Name.
c. Change password to the Verizon account password.
3. Restart and that's it.

Thank you for your post. When I moved to another home, Verizon sent me the Westell 6100 and I had been having trouble staying connected to the Internet with my Airport. Last night, I loss wireless access and the Airport status in the menu bar read "Looking for a PPPoE connection". Verizon customer support was able to get me back online, albeit with only a direct Ethernet connection between my iBook and the 6100.
I found your post and followed your instructions. Now all the iBooks in our household are back online via the Airport. Thank you very much!
iBook G4 933Mhz Mac OS X (10.4.7)

Configure TC and Airport Extreme Base Stations with different channels

I had to do some serious workarounds to use the Airport Extreme Base Stations as an access point with the same wireless network name primarily due to channel overlap. I thought I would post my results here since I didnt' find a good article online.
Also, I found the Snow Leopard verison (5.4.2) of the Airport Setup Utility far superior to Lion's Airport Utility (6.x) in terms of advanced setup.
Setup is a 3 flloor house where the 3 wired network locations have wireless overlap. The problem was that the access points would not hand off the wireless signal because the channels for each airport/TC were automatically set to the same channel. In non-apple setups, this is how you force a wireless client to switch access points (since the wireless software on your client/mac/windows can detect which access point is stronger and moves to the alternate channel.
Using apple's "Extend this wireless network" option removes any ability to manually configure wireless channels. I am writing this from memory, so feel free to ask questions and I will track this topic:
Procedure
Setup time capsule as your base station. Do all the setup for your wireless and guest networks. Manually configure the network and change the wireless channel to a specific channel for a/b/g networks (e.g., 3) and n networks (e.g, 167).
Plug your first airport extreme/access point into your wired network. Do not plug it into the "internet" ethernet plug, use one of the 3 ethernet switch locations
Use the airport utility to first configure it to "extend" your wired network.
Then, go in and reconfigure it manually in the airport utility. Choose the option to setup a "new network" and name the network the same as the TC wireless network name, security, etc.
Change the channel from "auto" to a different channel than the TC (e.g., 6 and 137).
Now go to the top tab and click on the "internet" icon
Go to the DHCP tab and change it to "bridge mode." This will tell the AE to not give out IP addresses (the TC will do this for you). If you get an error that the IP ranges conflict, you have not done this
Note that if you have a guest network setup, you will need to set this up on the AE as well.
Now test your airport setup. Take your client (macbook, iOS device) and connect to your network. Move to a spot near the TC and pull up a web page. Keep an eye on the signal strength and beginv moving toward the AE. Refresh the page as you move around. You should at some point see the signal strength increase. Refresh your page again. You should be now connected to to the AE. I have found that Macbooks do a better job than iOS devices because you get an extra signal bar to measure strength, and they have larger antennas which allows you to better measure problems with handoff
Another test you can do is to start backing up on your TC and then test the move. The handoff will truly show you that the TC is handling the process but the AE is relaying to the TC for backup.
If you need to setup another AE, simply follow setups 3-10.
I hope this helps others. I've done this setup 100 times on Linksys devices and although they are cumbersome, they at least allow me to do this setup much more quickly and easily than the apple products.

I had to do some serious workarounds to use the Airport Extreme Base Stations as an access point with the same wireless network name primarily due to channel overlap. I thought I would post my results here since I didnt' find a good article online.
Also, I found the Snow Leopard verison (5.4.2) of the Airport Setup Utility far superior to Lion's Airport Utility (6.x) in terms of advanced setup.
Setup is a 3 flloor house where the 3 wired network locations have wireless overlap. The problem was that the access points would not hand off the wireless signal because the channels for each airport/TC were automatically set to the same channel. In non-apple setups, this is how you force a wireless client to switch access points (since the wireless software on your client/mac/windows can detect which access point is stronger and moves to the alternate channel.
Using apple's "Extend this wireless network" option removes any ability to manually configure wireless channels. I am writing this from memory, so feel free to ask questions and I will track this topic:
Procedure
Setup time capsule as your base station. Do all the setup for your wireless and guest networks. Manually configure the network and change the wireless channel to a specific channel for a/b/g networks (e.g., 3) and n networks (e.g, 167).
Plug your first airport extreme/access point into your wired network. Do not plug it into the "internet" ethernet plug, use one of the 3 ethernet switch locations
Use the airport utility to first configure it to "extend" your wired network.
Then, go in and reconfigure it manually in the airport utility. Choose the option to setup a "new network" and name the network the same as the TC wireless network name, security, etc.
Change the channel from "auto" to a different channel than the TC (e.g., 6 and 137).
Now go to the top tab and click on the "internet" icon
Go to the DHCP tab and change it to "bridge mode." This will tell the AE to not give out IP addresses (the TC will do this for you). If you get an error that the IP ranges conflict, you have not done this
Note that if you have a guest network setup, you will need to set this up on the AE as well.
Now test your airport setup. Take your client (macbook, iOS device) and connect to your network. Move to a spot near the TC and pull up a web page. Keep an eye on the signal strength and beginv moving toward the AE. Refresh the page as you move around. You should at some point see the signal strength increase. Refresh your page again. You should be now connected to to the AE. I have found that Macbooks do a better job than iOS devices because you get an extra signal bar to measure strength, and they have larger antennas which allows you to better measure problems with handoff
Another test you can do is to start backing up on your TC and then test the move. The handoff will truly show you that the TC is handling the process but the AE is relaying to the TC for backup.
If you need to setup another AE, simply follow setups 3-10.
I hope this helps others. I've done this setup 100 times on Linksys devices and although they are cumbersome, they at least allow me to do this setup much more quickly and easily than the apple products.

I have internet optic fiber connection and I'm trying to configure it with my Airport Express but doesn't works, appears that I have IP and DNS, as I'm a computers dummy , who could help me to configuration it, please?

I have internet optic fiber connection and I'm trying to configure it with my Airport Express but doesn't works, appears that I have IP and DNS, as I'm a computers dummy , who could help me to configuration it, please?

You're welcome.
Voicemail is left at your carrier's server. That will continue to work unless you report your iPhone as lost or stolen with your carrier.
You may never find it again and you can't if the iPhone remains offline or out of service which means the iPhone is powered off or doesn't have cellular reception.

HT4145 Does this article apply to OS X Lion and Airport Utility 6.0? Reason: Airport Utility cannot find my Airport Extreme (4th generation) wirelessly on my Time Capsule configured network even although the firmware in both units is up to date.

Does this article apply to OS X Lion and Airport Utility 6.0?
Reason: Airport Utility cannot find my Airport Extreme (4th generation) wirelessly on my Time Capsule configured network even although the firmware in both units is up to date.

I thought you were trying to Extend the network with an Express as the article mentions you pointed to...
You can't find the Airport Extreme then...
I woudl suggest doing a Factory reset....
http://support.apple.com/kb/HT3728
Then you should be able to set it up just as you did when it was new....
Factory default reset (using reset button)
If the AirPort Base Station or Time Capsule isn't accessible from AirPort Utility, the Factory Default reset can be accomplished by using the reset button.
Unplug the AirPort Base Station or Time Capsule from power.
Press and hold the reset button with a pen or pencil, then plug the AirPort Base Station or Time Capsule back in while continuing to hold the button until you see the light (LED) flash rapidly. This should happen after a few seconds.
Release the button. This will factory default reset the AirPort Base Station or Time Capsule.

EMac and Airport Extreme

I have an eMac running OS X 10.3.9 with no airport card installed and no DVD drive. I connect to the internet with an ethernet cable from my eMac to my Verizon DSL (Westell Wirespeed) modem.
I just purchased a Macbook and an Airport Extreme base station and cannot get it up and running. Does the new Airport Extreme base station require 10.4 and later? Does my eMac need an Airport Card? How can I get this to work? After trying to configure things using the Airport Utilit on the eMac, I had no internet connection on the eMac or the Macbook. After failing with a Linksys router at first yesterday, I am almost ready to send everything back!
Thank you for any help anyone can offer!

If you are new to networks, it might not be too easy for you, but let's make a start.
You can't set up your extreme from the emac unless it is running X.4.8 AND is connected to the extreme via ethernet. If your macbook has X.4.8 and a wifi card you can use that, or you can also do it by ethernet from your macbook, there might be advantages by doing this.
Once you have installed the software on your macbook, open airport utility and you should see the extreme. Once you have done this you might be able to set things up yourself, if not come back, BUT:
You can't set things up from your emac, once they are set up you cannot use your emac wirelesly because it has no wifi card. You can of course connect it to a LAN port on the extreme by ethernet and join the network which will let you use the internet and share files with other macs (your macbook) on the network.

Cisco ASA 5505 and Airport Extreme

We have an office that uses an Airport Extreme as part of the network. The Airport Extreme uses a Cisco ASA 5505 as its gateway. The Cisco provides site to site VPN capabilities with other remote offices. We just got this configuration partially working and it works great for outbound connections.
But I have been unable to get an inbound connection to machines that are behind the Airport Extreme.
The goal is to access machines behind the Airport Extreme by way of RDP and also for use as drive and printer shares.
What do I need to do on the Airport to achieve this goal?
Thank you,
Lebby

Lebby,
I suspect it's not the AX that's the problem but the Cisco router, no doubt you have NAT enabled on that so that any inbound connection not initiated from inside just get's blocked.
You'll need to configure NAT on the Cisco first.
Regards,
Shawn

Problems setting up Verizon DSL (DHCP) and AirPort Extreme

I have Verizon DSL with DHCP and old router (Linksys WRT54G). I've bought iMac and new router (AirPort Extreme) to connect to iMac wirelessly. I have a Windows computer connected to the Linksys WRT54G. Now here is the story. I can connect verizon DSL modem (it's in bridge mode) to PC directly and connect to the Internet. When I plug AirPort between the DSL modem and PC, auto-configuration doesn't work, AirPort utility says there is problem with internet connection. Router simply can't obtain IP address from verizon's DHCP server. I've tried to copy DNS server addressed from the IP configuration in Windows, the AirPort light went green and Windows indicated connection as successful, however I still cound't browse the Internet because gateway is not set. Any ideas how to make AirPort connect to the internet using DHCP instead of manual settings? I can try to do it from the mac if needed, I don't think it would make any difference though.

Welcome to the discussions!
Sorry, I can't quite track exactly what you are trying to do.
What would the network that you are trying to set up look like?
Modem>AirPort Extreme>Computers? Are you saying that you won't be using the Linksys in the new setup?
Sounds like you need to set the Airport Extreme up to supply PPPoE service (which the Linksys is doing now-if the modem is in bridge mode), but I will wait for your response before offering specific info.
If you've been fiddling with settings, we may need to do a hard-reset on the AX to start over. You should not be fiddling with DNS, etc. Almost always, these settings are done automatically when you have the device set up correctly.

I have both TimeCapsule and Airport, and run two mac computers in the house on the one network. The airport often can not be found, and the signal is incredibly weak unless in the same room as the modem. Previously our signal was strong and effective.

The signal has been strong and effective previously and as far as i'm aware that nothing else in the house has changed. We have two apple computers, appletv, an ipad, 2 iphones, time capsule, and airport all running off the same network. If there is product, a configuration or program we can get to help diagnose and or solve any connectivity issue that would be awesome

The Powerline adapters mentioned by edex67 are your only hope if you cannot run an Ethernet cable.
Even if the home and office are on the same electrical circuit, you won't really know how well the Powerline adapters might work until you actually try them out at your location.
For that reason, it would be a good idea to understand the store's return policy before you buy.

Network set up using airport extreme, time capsule and airport express

I have searched for relevant answers but can only find different bits here and there.
My set up is as follows:
I have a Linksys wireless router running a stable wireless network for the other computer users in the house and wish to create an extended, additional network using airport extreme connected to the Linksys by ethernet to create the network and then time capsule close to my Mac Mini on my desktop and airport express at the other end of the house to try and extend the range of the network.
I have been trying for 4 days to set this up but without success. I have tried all of the options mentioned in different posts, using WDS, extending a new network etc. I can get connection between the three devices but monitoring on iStumbler there appears to be little improvement in the strength of the signal, iStumbler also shows the time capsule dropping it's signal totally every 10 or so seconds for a few seconds and then I get a positive signal strength for another ten seconds or so.
Can anyone help, it is driving me insane. I am a recent convert to apple computing and have been hugely impressed with all products until now. The claim that the set up of these wireless products is simple seems to be very exaggerated.
I am happy to provide any relevant system or hardware information.
Thanks in anticipation.

I have an AirPort Extreme acting as a wireless base station, connected to a BT router by ethernet.
Then the correct setting for Connection Sharing on the AirPort Extreme would be "Off (Bridge Mode)".
If I set Connection Sharing to "Share a public IP address", I'm told that: "The DCHP range you have entered conflicts with the WAN IP address of your Apple Wi-Fi base station"
Exactly. You have two routers....The BT device and the AirPort Extreme in series with both of them trying to act as the "main" router when you configure the AirPort this way. That won't work.
Only one can be the main router, and it must be the BT device in your setup. So, the AirPort Extreme....and any other AirPorts on your network must be setup to work in Bridge Mode to allow the network to operate correctly.

My network, based on modem, wifi router (Airport Extreme),Time Capsule and Airport Express simply disconnects with all the lights green on the modem and Extreme, but the other components offline, 5 or so times per day. I suspect the Extreme.

I have a Cisco System3 modem, feeding an Airport Extreme, which connects wirelessly a Timecapsules and an Airport Express both of which extend the network, ie send out more WiFi signal. The system worked well for a long time, say a year and a half and then it started dropping out. All the lights on the modem and airport Extreme stay green, but the other two components are blinking yellow. I've tried limiting the channels, but there are few sources in my neighborhood. I have tried resetting the Extreme which worked for a week and now it's back to its random disconnect behavior. I have read some of these blogs and no one seems to know what to do, especially not Apple. Do I just get another router or what? What do I lose if I use a non Apple router and what would you suggest?

Welcome to the discussion area, Junkcanoe!
I don't have a setup like yours, but might be able to offer some assistance.
Basically I have two jacks, a TC and an AE and I'd like to create a roaming network. Both of them are set to bridge mode with the same SSID, WPA2 security, same password, etc.
This would be the normal way to set up a roaming network, but the wild card here is that we don't know anything about how the main router that supplies the ethernet connections (valid IP addresses) to the condos might be configured.
For example, most apartments, hotels, etc that provide ethernet jacks usually limit the number of devices that can connect to each jack. Hotels tend to limit this to one or two devices. I counted six devices that you say will work properly plus a few more. Since you have two separate ethernet jacks, you may be looking at a situation where each jack is allocated a total of 4 devices, or valid IP addresses.
The bottom line here is that we won't be able to make much progress until we know more how the main router there has been configured. Is it possible for you to ask the complex manager (who will probably need to ask the IT guy) how many devices are allowed to connect per ethernet jack? Another way to ask the same question is how may valid IP addresses will each ethernet jack allow?
If you can, could I ask you to perform an experiment? Rather than have both the AirPort Extreme and Time Capsule each connect to a separate ethernet jack, can you temporarily move one device near the other and connect them together using an ethernet cable? (Or, use a long ethernet cable if you don't want to move either device) LAN <-> port on one to LAN <-> port on the other. In other words, you'll only be using one of the ethernet ports in the condo for this experiment.
Any difference in performance or number of devices allowed to connect?
Message was edited by: Bob Timmons

Apple TV Inference with Time Capsule and Airport express?

I have recently bought an Apple TV 2, which seem to be working fine, however since installing it on my wireless network both my Time Capsule and Airport Express can't be found. Following some fault finding it seems that when I unplug the Apple TV I can reconfingure the TC and AE.
The TC and AE are configured to join my existing network....and have happy sat there for a few years.
I would really welcome any ideas.
Thanks
R

Welcome to the discussions!
It sounds like you have the basic configuration covered correctly.
You might want to check some settings on the TC:
Wireless Mode would be create a wireless network
"Allow this network to be extended" should be checked
The AX should be set to "extend a wireless network"
The "allow wireless clients" box should be checked
In this configuration, the ethernet port on the AX is active so things should work.
A minor point...Although the TC is a dual band device, the AirPort Express is not. Can you make sure that that the Express is connecting to the "main" network on your TC? The "guest" network cannot be "extended".
If you place your laptop close to the Express and hold down the option key while you click on the AirPort icon, some connection information will be displayed. The MAC address of the device that the laptop is connecting to will be indicated. Make sure that that this is the MAC address of the AX, and not the TC.
Another note...If you have not changed the default "main" network, the radio mode is broadcasting 802.11n only at 5 GHz. These higher frequencies are absorbed by walls, ceilings and any obstructions much more quickly than 2.4 GHz signals. So, if you AX is some distance away, you may not be receiving a strong signal for the device at that location.
If you have a signal strength utility on your laptop (the "bars" at the top of the screen are not a very good indicator of actual signal strength), turn off the AX and take a reading to see what kind of signal the Express is receiving where it is located.
Please post back with your results.

Extending a network with Time Capsule and AirPort Extreme (via Belkin powerline)

Hello -
I've seen many topics about extending wireless networks here, but none seems to resolve the issue I'm having. I currently have a setup where a DSL cable modem is connected to a Time Capsule and I need to extend this network to another room using an AirPort Extreme.
I live in a very old apartment in Brazil and the walls seem to block the signal from one room to another, hence the need to extend it. Since wireless signal is very weak between rooms, I bought a Belkin powerline AV500 so I could connect both Time Capsule and AirPort using the electrical power at home (just installing a regular Ethernet cable between rooms is not an option).
I started with the basics: configure the Time Capsule + DSL as a standalone network, and it works perfectly within it's range. Then I connected the Belking powerline, plugged a MacBook via Ethernet on the other end and still got very good results (actually better speed than expected). Used it for a while with streaming and other network intensive tasks to make sure it could sustain the connection.
Finally, pluggned the AirPort Extreme on the Belking powerline and this is where the problems started. AirPort Utility 6.3.1 only gives me the option of extending a network wirelessly - it doesn't seem to give me the option of extending it via Etherenet (roaming), which is not good in my case. Luckly I had a copy of AirPort Utility 5.6 which seems to do the job (or I thought so), but it's still not working well.
Although I managed to configure both with the same name, it doesn't seem reliable and some devices (the iPhone 5, for example) are unable to connect and end up with a self-asigned IP address. I'm almost sure I'm doing something wrong on the setup, as I've seen a similar setup working before, so if anyone out there has any clue of what can be done, it will be much appreciated.
Attached the screenshots of both Time Capsule and AirPort Extreme configurations.
Thanks a lot,
-TM
AirPort Exteme:
Time Capsule:

Hello JuliaApple. Welcome to the Apple Discussions!
You have several ways to configure both base stations for what you are trying to do.
The simplest would be to configure the Time Capsule (TC) to "join" (AirPort Utility > Manual Setup > Wireless tab > Wireless Mode = Join a wireless network) your existing 802.11n AirPort Extreme Base Station (AEBSn). In this type of configuration the TC would perform as any other wireless client and not perform as a router. It will; however, still allow for both backups and sharing USB devices attached to it.

Configuring westell 6200 and airport

Similar Messages

Maybe you are looking for