Connecting Sound Blaster Audigy 2 ZS to A/V receive

Sorry if this is a stupid question, but this is the place to ask. I am thinking about purchasing this sound card for the purpose of connecting my htpc to my 5. home theater. I have all my cds ripped to my hard dri've using a lossless codec. Is this the route to go for connecting and what is the best method to connect the two?
Which is the best model? only going to use it for playing dvds and playing music ripped to harddri've. Is there any need for the platiunum ect is the sound card with rear outputs all I need?
r89msMessage Edited by r89ms on -03-2004 06:9 PM

I have my card hooked up to a Pioneer 500W 5. amp... the way to do this for games is to use the 6 channel analog in on the amplifier (usually for DVD's, has RCA in for front left/right, rear left/right, center and sub). Just use the outputs on your card with a headphone to RCA plug or cord and output one goes to the front channel, second output goes to rear channel, and third goes to center/sub (I forget which is left and which is right). The details on the plug are layed out in the THX console when you set the channel output (5., 6., 7.).
you could also use a mono minijack to RCA plug to connect the digital output on the card to your coax in on your reciever, but you will lose any 3d effects on games. The benefit of this is that you will not have any interference from the computer to the reciever, and you can have the reciever decode dolby digital 5. and DTS instead of the card, but I found that the card does a good enough job as is.Message Edited by RC735i on -03-2004 06:2 PM

Similar Messages

Help with Sound Blaster Audigy Value 24-bit..keeps crashing when connecting to the inter

pls help..every time i connect to the internet while playing mp3's or just any applications or programs that produces sound and even when streaming some clips through the internet, my computer restarts..any sound that is produced when i am online it will restart..but if i just surf the net without playing anything..it works fine...
how cn i solve this problem..
pls help..thnx
my spec:
AMD Sempron 2400+
Epox 8rda3i
Seagate 80gb
Palit GeForce 6600gt
Creative Sound Blaster Audigy Value 24-bit

screwguy_28 wrote:
is this the one?
IRQ 0 System timer OK
IRQ Standard 0/02-Key or Microsoft Natural PS/2 Keyboard OK
IRQ 3 Communications Port (COM2) OK
IRQ 4 Communications Port (COM) OK
IRQ 5 Uni'versal Serial Bus (USB) Controller OK
IRQ 6 Standard floppy disk controller OK
IRQ 8 System CMOS/real time clock OK
IRQ 9 Microsoft ACPI-Compliant System OK
IRQ 9 SCSI/RAID Host Controller OK
IRQ 0 MPU-40 Compatible MIDI Device OK
IRQ NVIDIA nForce PCI System Management OK
IRQ 2 PS/2 Compatible Mouse OK
IRQ 3 Numeric data processor OK
IRQ 4 Primary IDE Channel OK
IRQ 6 Sound Blaster Audigy OK
IRQ 8 SoftV92 Data Fax Modem OK
IRQ 9 NVIDIA GeForce 6600 GT OK
IRQ 2 Standard OpenHCD USB Host Controller OK
IRQ 22 Standard OpenHCD USB Host Controller OK
Everything seems to be OK so it's propably the drivers for your modem that is causing the issue. Just try if updating them helps anything.
Also, you can turn the MPU-40 (onboard MIDI/Game port) if you dont need it.
jutapa

Connecting PCMCIA Sound Blaster Audigy 2 ZS Notebook to Onkyo HT-S580 Recei

Hi
I have PCMCIA Sound Blaster Audigy 2 ZS Notebook audio card with my Thinkpad laptop.
I have bought Onkyo HT- S580 Hometheater system. I was hoping to connect the Line out, Line out2, Line out3 jacks to the receiver's Front, Surround(rear) and Center in jacks.
The color on the Onkyo Recei'ver end are Center - Green , Surround(rear) - Blue , Front - White
The color on the Creative Card end are Center- Orange , rear - Black , Front - Green
There is color difference between these two ends . Is it advisable to connect these two jacks ?
Please recommend the suitable cable type and name for this connection
Thanks

dilip wrote:
Hi I have PCMCIA Sound Blaster Audigy 2 ZS Notebook audio card with my Thinkpad laptop. I have bought Onkyo HT- S580 Hometheater system. I was hoping to connect the Line out, Line out2, Line out3 jacks to the receiver's Front, Surround(rear) and Center in jacks. The color on the Onkyo Recei'ver end are Center - Green , Surround(rear) - Blue , Front - White The color on the Creative Card end are Center- Orange , rear - Black , Front - Green There is color difference between these two ends . Is it advisable to connect these two jacks ? Please recommend the suitable cable type and name for this connection Thanks
Hi
Colours may vary --> just connect by the instructions from both manuals.
There are good explanations for
- Stereo and 4-Pole Jack Diagrams
- Connecting a multichannel home theater receiver
- cabletypes needed on connections
on User's Guide.
NOTE: This User's Guide can be found on your driver CD too.
Also, here is the Onkyo HT-S580 manual.
jutapaMessage Edited by jutapa on 0-0-2006 03:32 AM

PCMCIA Sound Blaster Audigy 2 ZS, connection to Mixer in and out

I have a PCMCIA Sound Blaster? Audigy? 2 ZS card attached to a laptop. I want to connect this laptop to a Denon X300 Mixer (http://www.platinum-records.com/Deno...0-prod7243.htm) so that I can untilize music on the laptop dri've, into the mixer board. Then I would like to stream this music back into the Computer for recording/manipulating on the laptop.
I think I have the link to the mixer figured out (use provided cable and a mini plug to RCA patch to the line in on the X300 Mixer) but the link back to the computer I am having issues with. Any Suggestions appreciated!
Spindu

dilip wrote:
Hi I have PCMCIA Sound Blaster Audigy 2 ZS Notebook audio card with my Thinkpad laptop. I have bought Onkyo HT- S580 Hometheater system. I was hoping to connect the Line out, Line out2, Line out3 jacks to the receiver's Front, Surround(rear) and Center in jacks. The color on the Onkyo Recei'ver end are Center - Green , Surround(rear) - Blue , Front - White The color on the Creative Card end are Center- Orange , rear - Black , Front - Green There is color difference between these two ends . Is it advisable to connect these two jacks ? Please recommend the suitable cable type and name for this connection Thanks
Hi
Colours may vary --> just connect by the instructions from both manuals.
There are good explanations for
- Stereo and 4-Pole Jack Diagrams
- Connecting a multichannel home theater receiver
- cabletypes needed on connections
on User's Guide.
NOTE: This User's Guide can be found on your driver CD too.
Also, here is the Onkyo HT-S580 manual.
jutapaMessage Edited by jutapa on 0-0-2006 03:32 AM

Pin Specifications for Creative Sound Blaster Audigy SB1394

;Pin Specifications for Creative Sound Blaster Audigy SB394 I have a Sound Blaster Audigy SB934 CA000-IAF Creative Tech '0 AA299J basically a Sound Blaster Audigy Platinum (wiouth the front bay for conectivity.)? And since I dont' have the front bay for heaphone and mic conectivity I was wondering if there is a spec sheet for the 40-Pin conectivity that is used for the front bay. I was wondering if anyone could provide me with such spec sheet so that I can try to conect my frontal Intel board plugs for headphone and microphone (would like to use my headset.)
There are a lot of pins on the card and well only about 8 in the conector for the front plugs. So if any dev from the forum is reading this I would greatly apreciate it if I could use my front Intel sound plugs on this old model card.
Thank you for all your help.

http://www.driverheaven.net/audio-general-technical-discussion/5279-creative-audigy-2-ad_ext-pin-assignment.html
That will help you with the pin assignments.......
And you can also try one of these to connect a lot more easily to your front panel audio jacks.......
www.x-tap.com
I used the above with four Audigy LS and SE's and it works a treat!

Sound blaster audigy midi p

I bought a SB Audigy2 value bulk, this card haven't a onboard midi port; is there the possibility to buy and connect a midi port?

Originally Posted by karloch
Hi everyone!
I recently purchased a Sound Blaster Audigy RX and I'm very pleased with the improved audio quality over the Intel HDA included in my motherboard.
However, I have a problem when playing MID files using hardware midi synthesis: I select the correct midi device "SB Audigy 5/Rx Synth A" and play the midi file using Windows Media Player. I can hear the tune, but with LOT of noise. As this problem is only happening with MIDI, I wonder if it is a driver issue or a faulty card. I have tried with official Creative drivers and with the Daniel_K's SB 5.3 support pack with same result.
I'm attaching an MP3 file of the MIDI output you can get a clear picture of what's happening.
ffaboss_short.zip
Should I replace my card or is it a software problem?
Hi karloch,
Pardon me for saying that I did not detect the noise you mentioned in your attached MP3 file. I can't be sure it's the noise or is it part of the music; especially towards the end of the playback. I'm using VLC player btw.
Perhaps, you may like to test it with another media player.
Cheers,
JL-CL

Sound blaster audigy 2 zs...NO SOUND! he

i've got a sound blaster audigy 2 zs...had it for two years...this morning, all of the sudden, it doesn't work...no sound...at all...i've tried uninstalling/reinstalling, speakers are fine (i've had to use the built in audio from my motherboard...NOT the greatest!)...anyone have any ideas, hints, ect. please...help me?:angry:

My Mobo=D875PBZ
perryjp20, After about 25 hours of troubleshooting, finally got my system up 'n running again, including the Soundcard. After a lot of wrong guesses for a "quick fix," simulated re-building the PC from the ground up:
Flashed back to an earlier BIOS (P27, mid-2004). Took out the ATI and Audigy soundcard, disconnected all dri'ves. Booted & shutdown. Added ATI card and monitor, then one 300 gig HD and DVD dri've, then formatted HD via installation of XP Pro, installed original Intel chipset drivers, and XP Pro SR and and set-up 2d partion on HD, installed ATI drivers (originals out of the box), then added Audigy card and its drivers (originals out of the box), then plugged in formatted 2d HD (250 gig). In the process now of adding the rest of my software and games. Shutdown and re-booted at each phase and monitored temps and voltage through BIOS at each phase to attempt to detect any problem with power supply or overheating -- saw no problems.
Will update ATI drivers soon, but reluctant to re-install Win XP Pro SR2.
Don't know what caused the failure of first the soundcard then the system "lost" the ATI card, then HD was corrupted. I was using the Firewire port of the Audigy card (connected to Canopus ADVC) when the sound started cracking/cutting-in-and-out and then went out altogether and the entire system went belly-up. Perhaps that Firewire port is bad? Other leading suspects: BIOS (which I had updated a couple of months ago) or perhaps the system had a worm or virus that Trend Micro did not pick up.

Is Creative Sound Blaster Audigy 2 NX USB sound card compatible with Dell deskt

Im considering buying the Creative Sound Blaster Audigy 2 NX USB sound card to use with a Dell desktop XPS 40, but recently read a forum message on another page that there was a issue with installing on a Dell Tower but no problems with installing on a laptop
any help is appreciated if there are any compatibility issues with using this sound card on a Dell desktop, Thanks
the main reason I would like to upgrade to this card is so my pc doesnt use the integrated audio which Id like better quality performance with a sound card and also dont want to install a internal card on the system

joaolfb,
Audigy 2 NX will need to be connected with the power adaptor inorder to run. USB will not be enough to sustain the power consumption of the sound card.
Jason

Capturing laserdisc AC3 signal with Sound Blaster Audigy 2 ZS Platinum

I'm considering converting my laserdisc collection over to DVD.
As far as PC hadware is concerned, I have the ATI All-In-Wonder 9800 Pro and the Sound Blaster Audigy 2 ZS Platinum Pro.
My system in a 3.2G P4 on a Intel D875PBZ board w/ 2Gig of memory. Connected are 3 dri'ves, (2) 250G SATA dri'ves and () old 250G IDE dri've that I keep archi'ves on.
The laserdisc player has the following:
AC-3 Bit Stream / PCM Optical Output AC-3 Bit Stream / PCM Coaxial Output PCM Coaxial Output
I was planning to use the optical input of the soundcard but was unsure what to use to capture the digital stream to capture the entire surround channel info. Normally audio is captured as an uncompressed WAV and then converted to AC3 which to me is a wasted step since it's only going to wind up as AC3 again
I've used Virtual dub in the past to capture TV broadcasts, but I seem to be at a loss on this current venture. Any assistance will be great

Alright, let me just double check...
As long as the output from my laserdisc is 48K then things should work fine and I should receive the entire unadulterated stream, no data padding or modification. If it's not 48k then it won't. This is as long as I save it as 2. PCM audio stream
The audiobitrate for AC3 should be at 384k, and this will be preserved using the above method?
From what I'm reading, this unprocessed stream should sound like white noise. Once processed by cooledit , Soundforge or besweet I should have the DD 5. soundtrack intact and not a 2 channel AC stream?
Sorry if I am rephrasing things but I just want to be absolutly certain when I start this project .
Message Edited by madmax66 on -6-2004 02:40 AM

Creative Sound Blaster Audigy 2 B4

Ok so as listed above, my current soundcard is a Creative Sound Blaster Audigy 2 B400, now when you google that the card doesnt come up unless its a ZS? My card is NOT a ZS though, its exactly as stated. Anyway, since its almost impossible to find I HAVE found a picture of the back of the card:
http://mayhem.prod.googlepages.com/p...inout-full.jpg
Now on to my question. I'm looking to buy?the Logitech Z-5500 5. surround sound (Digital) for my computer, now, I want to be sure that this card can support two things.
) The digital input itself, my card has a white "Digital" input, so obviously my first guess is yes.
2) This cable: http://www.monstercable.com/productdisplay.asp?pin=600
And if it can support that cable, will it benefit me? Sorry for the trouble, I just dont want to spend the money and not be able to support it. Thanks for the help.

Kenttheman wrote:
Ok so as listed above, my current soundcard is a Creative Sound Blaster Audigy 2 B400, now when you google that the card doesnt come up unless its a ZS? My card is NOT a ZS though, its exactly as stated. Anyway, since its almost impossible to find I HAVE found a picture of the back of the card:
http://mayhem.prod.googlepages.com/p...inout-full.jpg
Now on to my question. I'm looking to buy the Logitech Z-5500 5. surround sound (Digital) for my computer, now, I want to be sure that this card can support two things.
) The digital input itself, my card has a white "Digital" input, so obviously my first guess is yes.
2) This cable: http://www.monstercable.com/productdisplay.asp?pin=600
And if it can support that cable, will it benefit me? Sorry for the trouble, I just dont want to spend the money and not be able to support it. Thanks for the help.
By the Creative audio product database, SB0400 = Sound Blaster Audigy 2 Value. You'll find the User's Guide through Support->Product Documentation ... ther're diagrams for connectivity in guide. It's possible you need [url="http://us.creative.com/products/product.asp?category=&subcategory=6&product=780">t his[/url] addon for S/PDIF connections.
jutapa
Message Edited by jutapa on 04-27-2008 04:2 PM

Creative sound blaster audigy 2 zs h

I have creative sound blaster audigy 2 zs card and a set of AV labs, amped 7. sound system speakers. i have 4 input wires to plug into the card and it only seems to have 3 output jacks. When i go and calibrate the speakers i am missing out on my two surround speakers. how should i be hooking these up. There is probaly a simple ansew to this but it has me stumped. help please

Please read Creative's speaker connectivity guide: <A href="]http://ask.americas.creative.com/SRVS/CGI-BIN/WEBCGI.EXE/,/?St=787,E=0000000000070303557,K=54,Sxi=0,Question3 895=obj(3895): obj(3899))[/url] (Remove the space between ": obj", I wrote so cause I get a smiley otherwise:angry: )
As you will see in the article, the Audigy is fitted with two 4-pole connectors, which can carry 3-channels each. So you only need 3 wires for a 7. system, as you have 2 normal stereo plugs (3-pole) and 2 3-channel plugs (2*2+2*3=8). You will most probably need different wiring for your speaker system as it appears you have 4 stereo plugs.
Message Edited by alexs3d2 on <SPAN class=date_text>08-0-2005<SPAN class=time_text>:36 AM
Message Edited by alexs3d2 on <SPAN class=date_text>08-0-2005 <SPAN class=time_text>:37 AM
Message Edited by alexs3d2 on 08-0-2005 :39 AM

Creative Sound Blaster Audigy 2 ZS With WinTV Expr

Hi,
I am using a Creative Sound Blaster Audigy 2 ZS sound card, and I recently purchased a Hauppauge WinTV Express card, I have installed the card with no problems, but it says I have to connect a wire from the Line Out port on the WinTV card into the line In port on my sound card. I cannot find a line in port onm the back of my sound card so I am getting so sound from WinTV. Can anyone please tell me how to set it up correctly?
Thanks for your help,
MJJOS.

The Line In jack is the second jack from the Digital Out jack. If you have problem locating those jack, you can checkup the user guide too.
Jason

Mic2 front panel of sound blaster audigy 2 zs platinum still not worki

anyone..... please help!!!
I have a sound blaster audigy 2 zs platinum, everything is hooked up perfectly including all power cable, and connectors to the front dri've bay. I have a samson q7 microphone that is connected using xlr female to /4" plug to the mic2 jack but I got no input signal. I then tried also using just a /4" to /8" to the back mic port of the PCI, no signal either. My friend said this mic doesn't need any other power like a phantom power or anything
can you please help me!
X

If you're using a dynamic microphone, the Audigy 2 ZS dri've bay has a jumper which you can change for it to support dynamic microphones instead of electret microphones. However once this is done you won't be able to use electret mics until you've changed the jumper setting back.

Sound blaster Audigy 2zs platinum setup with creative inspire 5.1 digital 5

what should the setup be for the sound blaster Audigy 2zs platinum and the reati've inspire 5. digital 5500 because with the decoder in i only get center fl fr on games. i dont get sound from the rear speakers.but when i take the decoder out and just plug the 3 leads straight into the back of my sound card i get 5. any help plz.i done a thx sound test with the decoder in it does fl i can hear it but i can hear the center as well
and no sound comes out on the 2 rear speakers when doing the test.but when puting the 3 cables straight into the back of the sound card i runed the test and i could hear all the speakers fine even the rear speakers any help plz is this ment 2 happen or do i have to change some settings thanks for any help plz help me thanks.

I Have had a problem for ages. I have the Audigy 2 ZS Platinum and Inspire 5. digital 5500.
I have copied the advice I received/didnt recieve from creative.
Best of luck
Dear Martin
Thanks for your reply
I am sorry for the problem you are facing.
To achieve outputs from all the speaker during speaker test, you will need to have an analog connection, or digital DIN connection.
That will be possible if you connect the three line out jacks on your soundcard, to the three audio input (analog jacks->green,black,orange) on your speaker, if it has this connection. Or, you may connect them using Digital DIN, if they have this connection.
If you are using digital connection (coaxial, optical), there will be no way to achieve sound output from all the speakers during 5. speaker test, as they carry stereo signal.
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Services
Creative Labs Europe:
Original Message Follows:
Hi
I understand you must be busy, so no problem.
No I do not hear EAX when in Pro-logic mode. I only hear (depending on the game in question)
Half life two: front left-right and centre. NO rears
Fear: Front, left, right, & centre. No rears
Farcry Front left, right & centre. No Rears
When I run your speaker test HISSSSS, No Rears, no front left or right
Beats me?
Regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 24 January 2006 5:44
To: Martin
Dear Martin
I apologize for the delay on the answer.
If you select Dolby Prologic mode on the decoder, are you able to listen
the game audio, with EAX, in all of the speakers?
Regarding to the optional bay dri've, you can purchase it from ou
Best Regards
(Mod Note: Name Removed)
Original Message Follows:
Hello
Your email was helpful, unfortunately, not for my unit, you see I would
have
connected the Jack leads in by now if the inspire had Jack lead inputs
as
you describe
Please don't think I am being sarcastic, but from reading the
correspondence
below it would seem as if your department is having difficulty
understanding
my problem.
Also it would seem your department doesn't have the necessary technical
information on your very own product, so to help with your dilemma I
have
taken photos of the input/outputs on the Inspire unit.
You will clearly see the inspire has no inputs other than Coaxial and
Optic.
This leaves me back to my last post. I think the solution would be for
me to
purchase the correct processor, which would have come with the original
sound card had I not been a little tight on the money front.
I have attached a photo of the sound card with the processor, I would
love
to buy this processor but find myself unable to locate this product on
your
web site. Would you possibly be able to send me the correct link to this
item so I can buy this Processor Please?
Kind regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 8 January 2006 0:3
To: Martin
Subject: RE: CLE -
Dear Martin
Thanks for your reply
Your soundcard is Audigy 2 ZS
Your speaker is Creative Inspire 5. Digital 5500
You will need to have a 3:3 cable(with the color green, black, orange)
to connect your soundcard to your speaker, to achieve the 5. effects
with games.
Below is the connection:
- Connect line out jack of Audigy 2 ZS
to 'Front' of Creative Inspire 5. Digital 5500 using the green color
connection
- Connect line out 2 jack of Audigy 2 ZS
to 'Rear' of Creative Inspire 5. Digital 5500 using the black color
connection
- Connect line out 3 jack of Audigy 2 ZS
to 'Center/Subwoofer' of Creative Inspire 5. Digital 5500 using the
orange color connection
Once you have done the correct connection, play the game DOOM3.
Ensure you have selected either the EAX or surround option in the game
settings.
Does it work?
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Services
Creative Labs Europe
Original Message Follows:
You have lost me. Your sound card clearly states that I can have EAX
surround decoding from the sound card I have purchased.
All of the games on your web site claim to give me an environmental
effect
that will blow my mind, hence EAX.
All I have done wrong is NOT buying your decoder that comes with the
sound
card. My mistake.
All I want to do is re-address this issue and buy the correct
decoder/processor.
Can you point me to the correct link on your web site so I can buy the
correct decoder/processor?
As for the PCM out of the above cables, this foxes me as my other
equipment
only use Optical cabling on my Lexicon processor and from that I have DD
7., DTS 7. and meridian 5. lossless.
My issue is more to do with NO EAX from the rear and centre channels
while
in-game.
Kind regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 6 January 2006 09:3
To: Martin
Subject: RE: CLE - Technical Support Request (KMM887805I6636L0KM)
Dear Martin
Thanks for your reply
All commercial digital connection eg. optical or coaxial cable will only
carry PCM stereo signal. If you want to output the signal to a surround
5. with extra EAX environment effects, it will not be possible at all
since it is only restricted to stereo channel signal.
As per current industry limitations, we are bound to follow the standard
one-signal output for all our SPDIF and Optical output jacks. This is
something that is currently shared by all vendors for all products.
Please note that all games are not dolby digital, even they are , it
will require certain motherboard to encode it to dolby digital signal,
which our soundcard does not support.
You can only use analog connections to gain true 5. surround for
gaming..
email.
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Services
Creative Labs Europe
Original Message Follows:
Hi Joong
I don't fully understand your email, but I do get the gist of what
you're
saying and understand I need to connect the analogue cable to fully
appreciate the sound in EAX.
Would you be able to tell me what product I could buy from your
catalogue
which would marry up with the sound card I have, as I understand now
that
the Inspire 5. will not do the job.
Kind regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 6 January 2006 04:00
To: Martin
Subject: RE: CLE - Technical Support Request (KMM8875697I6636L0KM)
Dear Martin
Thank you for the reply.
Computer games written with support for 3D audio do not require a Dolby
Digital Interacti've Content Encoder (DICE) to output multichannel sound,
with no exceptions. Sound devices that support the real time encoder
technology from Dolby will simply receive the multichannel wave file
output and encode it in real time to a somewhat modified Dolby Digital
bitstream. Creative does not support the Dolby Digital Interacti've
Content Encoder on any of its sound cards.
The only difference between a Sound Blaster card and an audio card that
has a real time encoder, is that you can make a one-wire, digital
connection from your audio card to your home theater receiver and enjoy
discrete multichannel sound from the game. However there will be a
continuous, slight delay, known as "latency", as the encoder is creating
and transmitting the bitstream, and of course the compression scheme
being used is "lossy" (i.e. not bit-accurate).
If you want to enjoy 3D audio in 3D enabled PC games in multichannel
surround sound with a Sound Blaster card, it is recommended that you
connect the analog outputs of the sound card directly to the analog
inputs of the receiver. This will require 3 cables for 5. surround
sound, one for front right and left, one for rear left and right, and
another one for front center and subwoofer. Though it requires more
cables than a real time encoder system, it will not have any latency
issues. When connecting PC audio to a home theater receiver, Creative's
latest sound cards such as Sound Blaster Audigy, Sound Blaster Audigy 2
are likely to provide higher quality audio than any Dolby Digital real
time encode system available for the PC today.
Please retain all the previous correspondence when replying to this
email.
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Services
Please do not use this link to submit technical queries
Original Message Follows:
Hi
One particular game which has "in-game" DD is Farcry; I used this as my
benchmark disc for DD and to push my Nvidia 7800 GTX GPU's (I have tried
it
on friend's machines and they get the full surround effect so I Know
this
version is ok. I also have ALL of the game patches & updates.
I would like to point out that while playing Doom 3, Half Life 2,Fear,
Colin
McRae rally 04,FIFA 2004,Meddle of honour pacific assault, Rome, Shadow
ops, All these games have EAX HD, which is enabled within the options
menu
"in-game", But I do not get ANY use out of the rear's and I might as
well
listen in stereo.
No, inspire 5500 does not automatically switch while "in-game" when DD
is present as you would expect, but does if it was a Movie, which makes
me
think the DD stream isn't getting to the processor.
I originally thought I could put all this to rest if I could buy the
control
panel that would have come with the Sound card if I had not tried to
save
money, but every time I search your accessories site I get completely
lost,
it really isn't user friendly, the sub-menus are very time consuming and
point you in the wrong direction because they are not categorised as Joe
public would understand
I downloaded your TEST Movies and creative demo player utility, ran it
but
still no EAX HD or DD if that were present.
I want to put this card and Processor into my boys computer (which is
the
same Spec as mine and I will update to the FX series, but I am unwilling
if
I cannot find a logical reason why this set-up cannot work first.
Would it have anything to do with the pins on the Digital out on the
sound
card plug, the one I bought and was attached to the last email? Only
sending
certain channels down to the processor?
Regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 5 January 2006 08:09
To: Martin
Subject: RE: CLE - Technical Support Request (KMM8868993I6636L0KM)
Dear Martin
Thanks for your reply
Your speakers are fine as you mentioned that there is sound from all the
speakers when you are playing movie.
May i know what game are you playing when there are no sound from the
rear speakers?
Have you done the appropriate settings in the game to achieve the 5.
sound?
Is there any game patches that you will need to update?
Does the Dolby Digital LED light up when you are playing the game?
Please retain all the previous correspondence when replying to this
email.
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Servic
Original Message Follows:
Hi
I am sorry; I should have said the Inspire 5. was model number digital
5500
S/N SW330030026.
The inspire has these connection on the back of the processor
>From top/back of unit
Audio Outputs
Front
Rear
Centre/subwoofer
Audio inputs
Audio line in
Coaxial
Optical
DIN
The Din to a remotely located Subwoofer which has the speaker leads
inputting into it. Plus power.
Attached is the creative view of the controls menu and I have attached
the
invoice I was sent, it shows the lead I was told to fit.
As I said, I can now hear DD5. while within a movie from ALL speakers
BUT
no sound from rears during IN GAME DD5.
I do not use this PC for films only games.
Regards
Martin
If you are having a digital connection, it is normal for only get only
front left/right is you use the speaker test option.
http://us.creative.com/support/kb/article.asp?l=3&sid=4858
Speaker test only outputs from two front speakers?
You mentioned that that you are unable to get any sound from the rear
speakers when playing game right? May i know are you using a digital
connection? May i know what speaker settings have been made under
Creative Speaker settings?
Do get back to me on the above.
Thanks
Original Message Follows:
Operating System: Windows XP Professional x64 Edition
Creative Model Number: SBO 350
Computer Brand/Model: home made
Processor/CPU: AMD 64
Memory: Gig DDR 4
BIOS Type/Revision: 5. 39
System Board/Chipset: ASUS A8N-SLI Deluxe
Detailed Problem Description:
I have the above Sound card.
I also own Inspire 5. amp/processor
I Wanted to save money by connecting above sound
card to amp/processor
Connections on sound card made life very difficult
I contacted Creative for help. you told me to buy
an RCA to mini jack cord which also has other connections, from your
web site, (I tried to find
the product number for you, but your sub-menu
system is so poor I couldn't locate the RCA/mini
3.5 /to phono link for you) this cord connects
directly into the digital in, on the sound card (3.5 Mini jack) to the
coaxial input on the
inspire 5. amp/processor.
I have enabled ALL sp-diff settings and digital in
setting on every program/utility/kitchen sink and all.
I have an SP-Diff wire from DVD burner to creative
sound card, and yes its enabled and digital only
is selected.
I can play a DVD and see the inspire 5.
automatically change from Pro-logic to Dolby
digital when it See's an AC-3 stream.
when I try and play ANY game you say has EAX
,2,3,4 I cannot get any sound from my rear
speakers (see above in Dolby Digital ALL speakers
work correctly)
when I enter the set-up menu within the creative
software you supply with the sound card and select
5. speaker, digital only, test the speakers via
the white noise function, all i hear is left and
right noise. no centre, no rears.
I phoned you tech support line, the boy on the
phone didn't have much of a clue about your
product and I had to tell him what connections sit
on the inspire 5. series amp/processor.
I want to build another PC for my son, I want to
add the FX series sound card and amp, but i am not
willing to buy anything until i feel you have
helped me to solve this problem first.
please can you help, I am at the end of my tether
with this sound card.
kind regards
Martin Waite
Message Edited by Daniel-CL on 0-28-2006 :36 PM

Help! Creative Sound Blaster Audigy SE 7.1 Sound Card -

Hello. I've just recieved my new soundcard. It is the Creative Sound Blaster Audigy SE 7. Sound Card - OEM. (Located here: http://www.overclockers.co.uk/showp...atid=&subcat=)
My motherboard is a Asus A8N SLi se.
Now, I have put it in my motherboard, and just tried to install the drivers. I got an error though. It said "No compatible creative product detected." So I downloaded the drivers off the Creative site, and that did not help either. I disabled the onboard sound in the BIOS, and yet it still did not work. I tried plugging in the soundcard into each of the soundcard ports on my motherboard, and none of them detected the card.
I am sick of using onboard, and would like to get this problem fixed.
Some additional information:
The back audio/microphone ports on my motherboard never worked. I have been using the front sockets on my case. I see cables running from my motherboard to the front of my case. Maybe one of those cables need to go into my soundcard in order for it to work? I'm not sure which though, so I didn't try it, just incase.
Here are some screenshots of what I'm getting. They might help.
Drivers from the Creative site: http://img409.imageshack.us/img409/4528/gayap9.jpg
Drivers from the Creative CD: http://img520.imageshack.us/img520/3649/gaycdam5.jpg
Unknown Device in my Device Manager: http://img409.imageshack.us/img409/9924/unknownoj8.jpg
Now, I have no other creative parts in my computer. So this should be the soundcard, right?
Thanks in advanced for any replies.

Does the cable from the MB to the front I/O panel simuliar to this one? I installed a Audigy2 ZS in my other system and connected the black cable with the 0 pin connector to the card to use my front phone/mike jacks. Also in your device manager I see the Realtek AC97 still listed. When I installed the XM card in my 600 I disabled it in the BIOS so the entry does not show up in mine just the SB XF-I is displayed.
src="http://i.pbase.com/g6/89/377389/2/79327975.pMK94KJy.jpg" alt="IMG_008.JPG">
Dell XPS 600 Intel Pent D 830 3.0ghz
Chipset- Nvidia nForce4 SLI Intel Edition
WD 60gb HD
2gb Ram
DVD-ROM
DVD-RW (Plextor 760A)
Creative XF-I Extreme Music
Logitech X-540 speakers
EVGA 7950GT
Dell 2007WFP (I-SPS panel)
Win XP SP2
BIOS A

Connecting Sound Blaster Audigy 2 ZS to A/V receive

Similar Messages

Maybe you are looking for