Creative Input Needed

Hi all --
I have a bit of a dilemma seeing as how my Flash knowledge is
somewhat limited. I was hoping to get some creative input from the
masses in hopes of making this better. So, any input / suggestions
/ tips would be
greatly appreciated!
Below is the code that I use to do a few things:
1) Figure out exactly what second it is in the current year
2) Multiply that number by 3
3) Increment it by 3 every time the second changes
As it stands, it's just a simple text counter that gets
displayed in a dynamic text box. However, I need to do something
cool with this and I'm having trouble coming up with ideas.
Ideally, I'd like to make it look like an odometer, but I fear that
may be a bit over my head at this point.
So anyway, please feel free to offer up suggestions!

Okay, I did my best searching and I couldn't find anything that matched all your descriptors. I did do a search on both decoder numbers. SB0256 returned very little results, but with SB0466, I was able to find this ebay listing:
http://cgi.ebay.com/ws/eBayISAPI.dll...6_fvi%3D&_rdc=
This card isn't a Champion like you suggested. And with my complete lack of knowledge, I don't know what I/O dri've bay means. But since it is PCI and the decoder matches the number you gave me, this card should be adequete, right?
Whether it works or not, my search indicated it might be very hard for me to find that card (or any PCI card for that matter). Everything I saw was out of stock. I know this is a forum for Creative, but are there any other manufacturers that will allow me to accomplish my goal, either with current cards, or discontinued cards? Thanks again
Oh, and I will vote on that thread. I probably won't wait for them to release the decoder since I need it now, but I still believe Creative should be giving the customer what they want

Similar Messages

Creative Input Needed for Project !!!! Critique Please/Suggestions

Making a flyer to put up around the local college. Any suggestions? I know that the address needs more specifics, but as far as design/layout - any input?

Making a flyer to put up around the local college. Any suggestions? I know that the address needs more specifics, but as far as design/layout - any input?

Had to reset mac - we were members of creative cloud - need to re-install - cannot find initial set up emails how do we re-install

we had to reset our mac - lost the apps for creative cloud - need to re-install how do we do it

Edman27 please see Install and update apps - https://helpx.adobe.com/creative-cloud/help/install-apps.html for information on how to reinstall the Adobe Creative applications included with your membership.

What's the voltage input needed to run and charge the iPad 4?

What's the voltage input needed to run and charge the iPad 4?

As long as the charger is rated for at least 10 watts or 2 amps it well charge the iPad just fine. A higher rated charger such as the 12 watt 2.4 amp charger will also charge the iPad, possibly a little faster, but it will not damage it. Chargers rated at 5 watts or 1 amp may charge an iPad very slowly if not at all.
Just be aware some cheaper dual port USB chargers share the 2 amps. It will charge an iPad in one port but adding another will reduce the current to both ports to 1 amp. An iPhone may charge fine but the power would be reduced to the lower level and slow an iPad charging on the other port. The one you link to will work fine although it looks as though one port is 5 watt/1 amp and the other is 10 watt/2 amp. There are many adapter's available that will supply 10 or 12 watts to both ports to future proof the charger giving you the capability to charge 2 iPads or other more demanding smart phones with larger batteries. I like Scosche reVolt chargers, they cost a little more but they are a quality product. If you want the best option go with a 12 watt charger which can speed up charging on many products a little more than a 10 watt can.

Creative cloud needs creative cloud to install

I am in a you need creative cloud loop. I try to install creative cloud and there is a message that opens during installation that says get creative cloud.
Its a loop that repeats and never goes anywhere
Kamron

Link for Download & Install & Setup & Activation problems may help
-Chat http://www.adobe.com/support/download-install/supportinfo/
OR
-http://helpx.adobe.com/creative-cloud/kb/error-downloading-cc-apps.html
-http://forums.adobe.com/community/download_install_setup
-http://helpx.adobe.com/creative-cloud/kb/troubleshoot-cc-installation-download.html
-http://helpx.adobe.com/x-productkb/global/errors-or-unexpected-behavior-websites.html
-http://helpx.adobe.com/creative-cloud/kb/unknown-server-error-launching-cc.html

Creative cloud needs password??

every time I start my computer, creative cloud asks me for my password to do updates?
Any suggestions. It has never dones this before and only after the last uopdate.

Hi Billy Arbour,
Welcome to Adobe Forum,
Please just place the original opm.db file on the desktop
Exit Creative Cloud app.
On Windows remove the opm.db file located here: C:\Users\<user>\AppData\Local\Adobe\OOBE
On Mac remove the opm.db file located here: <user>\Library\Application Support\Adobe\OOBE
Restart Creative Cloud Connection and sign in.
OR
Please try to update CC desktop: https://creative.adobe.com/products/creative-cloud and let us know
OR
Have you tried creating a new administrator account, logging out of your current account and into the new one to see if the behavior persists? Having to sign in and register that many times seems like something is not getting saved or changed properly when you complete the process.
Here are instructions for creating a new account if you need them:
Windows 7/8
http://windows.microsoft.com/en-IN/windows7/Create-a-user-account
http://social.technet.microsoft.com/wiki/contents/articles/create-a-ne w-user-account-in-windows-7.aspx
Mac
10.7 - http://support.apple.com/kb/PH4600
10.8 - http://support.apple.com/kb/PH11468
Also, I've heard that changing your Adobe ID password has made a difference in some rare cases.
http://helpx.adobe.com/x-productkb/policy-pricing/account-password-sig n-faq.html#manage_account
Regards,
Rajshree

I keep getting a message that Creative Cloud needs administrative permission to make changes or removals.

I have received many messages that needs a password to allow Creative Cloud to make administrative permission to make changes or removals. But nothing seems to change or get removed. My apps are up to date.

Please read, and reply back here with information https://forums.adobe.com/thread/1499014
IF YOU ARE MAC
-next link says After Effects, but check YOUR permissions !!!
-http://blogs.adobe.com/aftereffects/2014/06/permissions-mac-os-start-adobe-applications.ht ml
-Mac 10.9.3 workaround https://forums.adobe.com/thread/1489922
-more Mac 10.9.3 https://forums.adobe.com/thread/1491469
-and https://forums.adobe.com/thread/1507936
-Enable Mac Root User https://forums.adobe.com/thread/1156604
-more Root User http://forums.adobe.com/thread/879931
-and more root user http://forums.adobe.com/thread/940869?tstart=0

X220 Stereo mic input needed..

I need a stereo mic/audio input for a specific project.
I have the X220 and the Ultrbase 3.
I think the X220 mic input is Mono.
What is the Ultrabay mic input - Mono or Stero?
If mono, does anyone have a suggestion or method of getting L/R audio input into the X220?
or is that not possible.
Thanks
DaveG
X220/i5-2540M/3.3GHz/8GB/320GB/7200/Webcam /IPS/7Pro

It's probably easiest to get a USB adapter. Something like this may work if you're using 1/4 inch jack: http://www.newegg.com/Product/Product.aspx?Item=N82E16829111004
Shure has ones for XLR connectors: http://www.shure.com/americas/products/accessories/microphones/microphone-problem-solvers/x2u-xlr-to....

At a loss. Wiring a possessed house I think! Input needed

Need some help.
I know and have done a lot of networking No pro, but self taught. Did run Ethernet of my whole house (ex wife's house now ) pre wifi days. Running wires, using switches and routers. All worked. Have down a ton of wifi - all Apple gear for myself in my location, friends and family. Good to go. I currently run a bunch in my home for iPhones, computers, netflix, itunes server, Air Video for all devices. Flawless.
So I'm not a dummy at least. So……
To my dads house. My on going project for a year. Great house. Big. Hand built back in the '50's. All plaster. Well made.
1- His office - cable modem to Airport Extreme - named BASE. Across this room, one Airport express (all AX are older g units) for the stereo from computer.
Now when I try to extend this network only for him to use his iPhone with Apple Remote to control music, I have now bought 5 Airport Expresses - the signal will not carry for more than 10 feet at best in this house (it's possessed I swear). NOT KIDDING.
I put an Express 10 feet from the office to a kitchen, why because any further I get no signal connection.
From this Express another one 10 feet for a den.
But the signal is so weak it doesn't work.
The house is plaster - I guess very well plastered and who knows what metal lathering is behind the plaster? It's a ranch.
What could possibly abort wifi signal like this. Oh, I might add, no iPhones work in the house either. We're in NY.Long Island. Major ATT signal. Nada in house. Go outside no problem.
So I'm going to tackle this again this weekend. Start from scratch. Any insight? I'm asking because I'm at a loss and think I'M NUTS! LOL
What would make wifi not carry for any distance? Lot's of windows in the house too.
I'm on the verge of telling him to have cable run another wire and modem to the other side of the house.
I'm stumped. I was going to post a few times but can't imagine why I can't get this working. Feel like a dunce.
Right now he tells me it's no connection in the den. The last AX extender not 10 feet from him.
Thanks in advance.

In addition to metal, water also will cause significant reduction in signal. The higher the frequency, the worse the problem. (One of the reasons why in the past submarines needed to surface to use their radios.) Perhaps the plaster or wood is exceptionally wet or the particular plaster they used has a high metal content. You may want to try using only 2.4GHz instead of 5HGz because lower frequencies penetrate walls better. I'm grasping for straws, but I'm not sure what else you could try short of tearing down walls.
I will tell a story of one wiring job I did. My boss gave a quote and approval sight unseen. He normally didn't do this but due to various circumstances and time constraints, he took a gamble. The job was to install a DSL modem and wireless router for a doctor's office. The modem and router were in the managers office. The reception area in the next room would have two workstations about 15 feet away, connected wirelessly. The doctor's office would get one laptop connected wirelessly, about 100 feet at the other end of the building. The building was all wood construction so no one foresaw what happened next. The manager's computer was fine since it was wired. One of the wireless reception workstations was fine with full signal strength since it was a line of sight through an open doorway to the router. The other reception workstation was working but only had 50% signal strength. (Not line of sight to the router.) The doctor's laptop had zero bars. I moved the laptop next to the router and got 100% signal strength. I walked the laptop next to the workstation with line-of-sight, and still got 100%. I walked to the other reception workstation and got 50%, same as the workstation. I walked out of the reception area turned left and started to walk down the hallway to the doctor's office. I took no more than 5 steps and got zero bars! I walked back a few steps and the meter jumped to 50%. I had to do this a few times to fully convince myself. It was only a chance conversation I had with one of the nurses who recalled that the former occupant of the office was a dentist. So we surmised that the room that the router was in might have had the x-ray machine, so they would have lined the walls with lead or whatever. In any case, we ended up having to pull wires. But we learned that regardless of what it looks like on the outside... But this does sound quite similar to your experience.
There's also the time that my coworkers found that the whole wall was 1/4" steel plate. The walls were covered with drywall so we didn't know it was there until we ruined a half dozen drill bits. It seemed like it was armor plate steel. We think the building used to be a indoor gun range or something. And there was the time that we encountered hardened concrete walls at an office using a former military building. Fortunately neither of those had Wi-Fi but we likely would have had signal problems in both cases. It taught us that we can't assume and needed to do a thorough inspection ahead of time.
So while I don't think the house is possessed, I do suspect that the original builder used some funky local material. Maybe he was a conspiracy theorist and has tinfoil in all the walls.

My Creative Cloud needs an update, but says there is no internet connection, and disconnects shortly after. What can I do?

I wanted to install my creative cloud in order to access indesign. Although when I click download, it tells me to update the programme. So I do. And then it starts loading, but ends shortly after, telling me to check my internetconnection. The connection is absolutely fine, no problem, but it just won't install the update. This means that I can't use the creative cloud AT ALL, because none of the programmes I could be using will work due to the missing update. SIGH!!

Cdannevig are you on a managed network? If not please see Sign in, activation, or connection errors | CC, CS6, CS5.5 - http://helpx.adobe.com/x-productkb/policy-pricing/activation-network-issues.html for information on how resolve connection errors.

Imac sees no wi-fi networks. Other computers do! Some input needed!! Thanx!

Hi people.
I just got a intel imac 20inch with an airport extreme card. A few weeks ago i tried looking for networks.
At home i found 8 wi-fi networks in my area with help of a windows laptop. My mac...detected nothing.
I went back to the shop (a shop with apple certified people) to let them check it.
Their conclusion was that my card was functioning correctly.
The receipt stated that they streamed a movie through airport and that there was no noticable delay.
Their airport base station was located a few floors above their technical dept.
I got my mac back and i went straight to home. Same problem. No networks whatsoever...
Then i went to my friends house. He's got a old dell with a sitecom wlan card.
He can find 4-5 networks in his area. My mac can only find his network. I use Istumbler + Spectrum Widget and the strenght is 50% on a distance of 1,5m (5feet) to his router!
How is this possible?
I know that to access another network you need some data. But to detect a network with it's SSID on you just have to turn airport on to see it. Right?
I reinstalled osx and i am doing a software update right now. To 10.4.7.
Maybe that helps but i doubt it.
Can anyone shed some light?
Should i go directly to apple and have them look?
Thanx!!!
Intel Imac dual 2,0 Ghz Mac OS X (10.4.4)

The software update is done. No improvement.
I saw another post with an answer from duane wich made me think that the antenna of my airport extreme card is not inserted properly.
Unfortunately the new imac's are not opened easy.
I hope that's it. After all.....they did not open my mac. Sigh.
I'm gonna call apple care.

Adobe Photoshop in 'creative cloud' need language change, Please Help!!

I have Adobe Photoshop in 'Creative Cloud', It's in English and I want to change the language in Dutch. Please Help!!
I just started out with Photoshop on my mac. So every instruction I learned so far (not much) is in dutch. Can anyone provide me with some instructions!
Thank you so much
Hannah

There you go. How can I change the language of my Creative Cloud installation?
~ Arpit

Zgate abap development inputs need for sap mm point of view

Hi All.
Loooking for sap mm zgate module inputs.
Thanks in advance sap mm forum members.
Regards.
Parameshwar

ABAPer with some functional inputs helped to develop it
Edited by: paramerp on Aug 5, 2011 2:32 PM

Input Needed

Hi All,
I need information on the upgrade and migration strategy for PI 7.1 to 7.31/7.4 both single and dual stack.
I searched sdn and found a few relevant documents for migration( tool usage ) and the other document ( Decision making factors for upgrade ).
Do we have a standard guide available for the same. Or any pointers to relevant links in market place for the same.
Any help would be appreciated.
Thanks

Hi Amit,
If you have collected all SCN relevant document you only need to search the notes that can be useful for you like these:
1309239 - Configuration Wizard: PI NetWeaver initial setup
1689037 - Configuration Wizard: PI Self Test for AEX
1321868 - Configuration Wizard: PI Upgrade
Finally you can search your installation guide here: https://websmp203.sap-ag.de/~form/handler?_APP=00200682500000002672&_EVENT=DISPLAY&_SCENARIO=01100035870000000122&_HIER_…
Regards,

Desing input needed: JMS in cluster(s) for OSB

Hi
I have two admin servers prod A and prod B on two separate physical boxes.
prod A has managed servers MS1 and MS2. : Together they form cluster A
prod B has MS3 and MS4.: Together they form cluster B
Client forwards request to a loadbalancer which forwards request to either prod A or prod B based on load in environment.
Use case: I have to push some data in JMS queue on server. Client will call periodically and hit one OSB proxy service which basically gets data from queue and returns. Since I have two clusters thus I need to create two queues, one each on prod A and prod B. Now consider following scenario:
Client hits loadbalancer
loadbalancer forwards request to prod A. Queue on prod A was empty.
since I get empty response, I forward the same to prod B. Queue on prod B had data so returned it to client.
Here issue is I need to have communication between prod A and prod B. Also I need to implement manual fail over in case prod A or prod B is down.
My question is :-
Can more than one clusters, if they are not aware of each other (if they do - then together they form a single cluster if I am not wrong) share resources such as queues?
May be I am not clear or couple of concepts of mine are wrong...;-)
Please share your thoughts.
Thanks and Regards
Swapnil Kharwadkar

Barnes,
          Thanks for such a nice explaination. Let me tell what i did ealier for my set up and what is the problem i have right now.
          I deployed the application which is using the JMS in the single cluster environment which has 2 managed servers each from different physical servers.
          I configured one connection factory with the preoper JNDI name and default delivery mode as non persistant and deployed the connection factorey on the cluster in which i deployed the application.
          I configured one JMS server and deployed in one of the servers from the cluster with migratable method and persistant store as none.
          I configured one destination under this created JMS server and replicated the JNDI name in the cluster.
          The application can access the message from the queue on the server in which i deployed the JMS server, not from the other one, though i deployed the server with migratable service. This is the problem i cant access from the other server.
          I am not sure what i am doing wrong or what made me wrong. Please help me out.
          Jasmine

Creative Input Needed

Similar Messages

Maybe you are looking for