E61 - Cannot remember its access points when loose...

Hi,
I live in Canada but came a couple years ago from Europe with an E61 that I already owned. Even though I love the phone, I have had a recurrent problem which I haven't been able to resolve despite an extensive search on the net. As soon as I go in a tunnel, subway, building, underground.... I logically loose signal from my current network ... and the phone looses its current access point connection which prompts a menu to manually reselect the access point once the network is back. But, if I do not rapidly execute the manual selection of the access point on the phone, the phone kind of freezes, then reboots, reconnects to the network, asks me again to manually select my access point from the list. If again I don't make the selection, the phone will go in a loop and will reboot until it fully drains the battery ... and that's the other problem. If I don't pay attention, the phone will deplete its battery in a very short time by constantly rebooting...
I just came back from a trip in Europe and while I was connected to French phone networks, as soon as I would loose signal (in the fast train for instance), the access point selection menu would reappear..So, the problem is not just in Canada.
Any ideas, suggestions? I am up to date with my system. I checked it.
Thanks very much in advance for your help.

You don't mention it, but I would assume the software for the device is being installed using an administrator account...if not, you should make sure that it is installed that way...and check during the install to see if there is an option anywhere to install for all users...
Tomato 1.25vpn3.4 (SgtPepperKSU MOD) on a Buffalo WHR-HP-G54
D-Link DSM-320 (Wired)
Wii (Wireless) - PS3 (Wired), PSP (Wireless) - XBox360 (Wired)
SonyBDP-S360 (Wired)
Linksys NSLU2 Firmware Unslung 6.10 Beta unslung to a 2Gb thumb, w/1 Maxtor OneTouch III 200Gb
IOmega StorCenter ix2 1TB NAS
Linksys WVC54G w/FW V2.12EU
and assorted wired and wireless PCs and laptops

Similar Messages

I cannot remember my access code. how can I find it, or turn it off to put in a new code?

i cannot remember my access code. how can I find it, or turn it off to put in a new code?

(click to enlarge)
Connect it to a computer
click sync
then click restore
than restore with the backup created when you synced

LGBD390 blu-ray cannot find the access point of WRT160N/3.

I have been trying to set up the wireless connection to be able to view streamed movies from netflix through my LGBD390 blu-ray player. I have successfully connected the wireless router to my Embarq router. When I check status, it says it is enabled and connection is o.k. I have been on the phone with Linksys (and was charged $9.99 which did not solve my problem). I also have chatted and so far that has not worked either. I have downloaded the upgrade for the firmware. No matter what I do, the blu-ray cannot find the access point of the router.
Can you help?

thank you for your responsse Wizzard, but there are things I need to change that I don't know how to do. I have no idea how to assign static ip, subnet and gateway on the blu-ray. When I went to the link , it was actually for adifferent router than mine. I have a WRT160N/v3. I also did not know what to put in the protocol. and if I should just put the number in the beg. and ending. I also don't think I have an ethernet adapter. Maybe you could give me more information. Thanks in advance.

Its near impossible to get a Advanced datagrid to remember its opened nodes when it has fresh data

Theres a post in
http://www.mail-archive.com/[email protected]/msg85521.html//www.mail-archive.com/[email protected]/msg85521.html
which is basically saying its near impossible to get a Advanced datagrid to remember its opened nodes when it has fresh data
I'm having pretty much the same problem (exept I'm not filtering just getting the latest data from the server)as this guy and have been searching for a solution, heres what he said:
Sun, 02 Mar 2008 08:07:46 -0800
Hello guys,
I'm trying to filter my ADG without success :
I created a GroupingCollection from a flat ArrayCollection.
ADG's dataProvider is GroupingCollection.
First issue : refresh
if I filter the underlaying ArrayCollection, the related
groupingCollection doesn't refresh automatically (bug? feature?)
Actually I menaged to force gc.refresh() with some event( it is
impossible to listen on CollectionEventKind.REFRESH because of
infinite loop ac.refresh => gc.refresh )
Second issue (more important) : openNodes
Ok now that my gc is refreshed, the Tree in the ADG collapses itself
(ok let say that is normal), and I need it to expand all nodes that
were opened before.
I tried to do something like this :
var openNodes : Object = IHierarchicalCollectionView(
myADG.dataProvider ).openNodes;
gc.refresh();
myADG.dataProvider.openNodes = openNodes;
and it doesn't works.
next I tried this :
var openNodes : Object = IHierarchicalCollectionView(
myADG.dataProvider ).openNodes;
for each( var node : Object in openNodes )
IHierarchicalCollectionView( myADG.dataProvider.openNode( node )
guess what, doesn't work
I'm calling myADG.invalidateList() each time too.
I don't know what to do to achieve this simple task, I'm a bit
disappointed because I expected lot more from the brand new
AdvancedDataGrid and this basic functionality actually seems too hard
to implement.
I still hope I'm wrong and someone can show me the correct solution
Thank you all,
Adnan

Hi,
I remember the days when Oracle would practically give Oracle Financial s away just for the implementation consulting fees.
Yeah, IBM used to give-away DB2 also . . . .
Oracle Financial s away just for the implementation consulting fees. Yeah, but any ERP requires massive set-up costs. I once worked on an SAP effort that cost over $20,000,000.
complete with Microsoft head to headIn what? Oracle is far-and-away the world's most robust and flexible database, hundreds of times more powerful that SQL Server.
IMHO, it's like apples-to-oranges . . . .
Everyone is running SQL server Here, DICE shows over a hundred Oracle openings in the Boston area, that might help you:
http://seeker.dice.com/jobsearch/servlet/JobSearch?op=300&rel_code=1102&N=0&Hf=0&NUM_PER_PAGE=30&Ntk=JobSearchRanking&Ntx=mode+matchall&AREA_CODES=&AC_COUNTRY=1525&QUICK=1&ZIPCODE=&RADIUS=64.37376&ZC_COUNTRY=0&COUNTRY=1525&STAT_PROV=0&METRO_AREA=33.78715899%2C-84.39164034&TRAVEL=0&TAXTERM=0&SORTSPEC=0&FRMT=0&DAYSBACK=30&LOCATION_OPTION=2&FREE_TEXT=oracle&WHERE=Boston+MA&WHEREList=Boston+MA&SEARCH.x=0&SEARCH.y=0
Excel is the tool of choice for accountants and its integration withcubes is nothing short of stunning
Sorry, I must disagree! Yes, CPA's will download Oracle data into spreadsheets for analysis, but Excel is wanting, especially for hypothesis testing, correlational analysis and data mining. Oracle's ODM, however, is truly stunning, light-years ahead of PC-based tools:
http://www.rampant-books.com/book_2006_1_oracle_data_mining.htm
Larry make Oracle great again be cutting the costI cannot speak for Oracle Corporation, but Oracle XE is FREE, totally and completely free. Add-in Apex for free, and it's very competitive.
Hope this helps. . .
Don Burleson
Oracle Press author
Author of “Oracle Tuning: The Definitive Reference”
http://www.dba-oracle.com/bp/s_oracle_tuning_book.htm

On my iphone, icloud is set to an apple id that i no longer use and i keep getting asked to enter a password. Cannot remember the password. When i try to re-set the password, it sends a email to a address no longer used. Will not accept any dob i enter

I have icloud on my phone with an apple id that I no longer use. I keep getting asked to enter the password for this ID. However I can't remember the password.
When I try to re-set the password, a e-mail will be send to an address I no longer use and can't access.
I then try to answer the security questions, but the date of births I enter are not accepted
Any ideas?
Paul

Welcome to the Apple community.
This feature has been introduced to make stolen phones useless to those that have stolen them.
However it can also arise when the user has changed their Apple ID details with Apple and not made the same changes to their iCloud account/Find My Phone on their device before upgrading to iOS 7, or if you restore from a previous back up made before you changed your details.
The only solution is to change your Apple ID back to its previous state with Apple at My Apple ID, verify the changes, enter the password as requested on your device and then turn off "find my phone".
You should then change your Apple ID back to its current state, verify it once again, delete the iCloud account from your device and then log back in using your current Apple ID. Finally, turn "find my phone" back on once again.
This article provides more information about Activation Lock.

HP photosmart 7520 connects to wrong access point and looses connection

I recently installed a remote wireless access point in an outbuilding. I'm using a router with the same SSID and password as my main router with the same security settings. Only the main router is set to issue IP addresses. The system works fine with two laptops, a desktop, an Ipad and an Ipod. It provides continuous connections from my house to the outbuilding. Only the HP Photosmart seems to be an issue. At first the system worked fine then after a couple of days it lost its connection. I tried to the Wireless Setup Wizzard with no success. The Wireless Network Test results indicated that MAC address filtering may be enabled. This is not the case, MAC filtering in not enabled on either router. The next morning the printer was fine and connected again. I suspect that it is detecting the remote router and trying to connect through it. During the setup a warning came up indicating that two routers were detected with the same SSID and Password and that the printer might try to connect to the wrong router. It should not matter since the remote router connects and is issued IP addresses through the main router. The only difference in the routers is the BSSID. This uses the same number as the MAC filtering address, so I suspect this may be the problem. Any suggestions on a work around. The only thing I have found that solves the problem is turning off the remote router.

Hello there -
Is it possible your new remote access point only supports the 5Ghz band for N connection, or that it's connected to your primary router through a wireless N connection in the 5Ghz band? The 7520 only supports 2.4Ghz N connections. If your primary access point supports both 2.4Ghz and 5Ghz, that is likely why it's able to connect there while it cannot connect to the new access point. Many newer laptops and iPad/pods utilize 5Ghz N, which would explain why they can connect and your 7520 cannot. I'd recommend moving the 7520 closer to the primary router and using AirPrint to send your jobs.
***I am an HP employee***
The comments above represent myself and do not reflect the opinions of HP.

I have an old Apple ID connected to a discontinued e-mail address. I want to delete it. I cannot remember my password and when I try to change the password using the security questions, it rejects my birth date! I can't change it by cancelled e-mail.

I have an old Apple ID associated with a discontinued e-mail address. It keeps popping up when I try to update apps. I don't remember the password. When I try to change it by security questions, it rejects my birthdate! I can't change it by e-mail because I no longer have access to the e-mail. All I really want to do is cancel this old ID. How can I do this? Obviously, I have a new ID, since I am using this support community.

You'll have to contact iTunes store support to see if they can help you with this: http://www.apple.com/emea/support/itunes/contact.html.

How to configure wrt54g router as an access point when connected to a 3Com switch

I'm trying to use my linksys router as an access point to keep from having to make more network drops. I can't figure out which IP address/gateway to use on my router to get it to communicate with my switch. The 3Com switch address is 10.1.10.250, gateway is 10.1.10.1, netmask is 255,255,255,0.The linksys router has been reset to defaults.
I know that it can be done but I'm having the hardest time making it work.

For the DD-WRT firmware, you can try this link .
For the price of your Acess Point you can try this link .

HT1212 i cannot access my iphone because i cannot remember my passcode but when i go to restore on itunes it wont allow me?

My son has locked my phone with a passcode, I have go onto my Itunes and tried to restore it and it wont allow it so what do i do????

Depends on exactly what you mean by "it wont allow it" -- did you read and try the following from http://support.apple.com/kb/ht1212?
If you see one of following alerts, you need to erase the device:
"iTunes could not connect to the [device] because it is locked with a passcode. You must enter your passcode on the [device] before it can be used with iTunes."
"You haven't chosen to have [device] trust this computer"
If you have Find My iPhone enabled, you can use Remote Wipe to erase the contents of your device. If you have been using iCloud to back up, you may be able to restore the most recent backup to reset the passcode after the device has been erased.
Alternatively, place the device in recovery mode and restore it to erase the device:
Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to shut down.
While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
Continue holding the Home button until you see the Connect to iTunes screen.
iTunes will alert you that it has detected a device in recovery mode. Click OK, and then restore the device.

Application windows remembering original anchor points when moving or resizing

Recently it seems that most of my windows, especially iTunes, Safari, and Finder, seem to retain the anchor points from when they were opened and revert to their original position if a window is resized. I've noticed the following odd behaviors that seem to be related to this problem:
After moving an iTunes or Safari window, right-clicking will open the context menu in a location that corresponds to where the window was originally placed.
After moving a window, a drag-n-drop target remains relative to where the window was. For example, in iTunes, if I open the application and move the window, it becomes impossible to drag a song into a playlist (unless I drag the song to the location where that playlist was when the window originally opened). The same sort of thing happens with Finder windows. In the image below, a screen grab of a Safari window, I right-clicked on the signal strength display pictured on the phone to the left; notice the context menu way off to the right of the Safari window.
Resizing a Safari window makes the window first snap back to the original location, then allows the resize to occur.
Opening/closing a tab in Safari, when the action causes the tab bar to appear or disappear, causes the Safari window to snap back to the original anchored position.
I've noticed this behavior over the past week or so. It was about a week ago that I installed the 10.9.5 update to the OS, but I'm not sure if the problem pre-dated the update or not.
This is driving me insane. Does anyone have any suggestions or, hopefully, a fix?
Thanks.

You can try running the combo update.
10.9.5 Combo Update

For some reason my attempts to download free apps result in automatically opening a box that require payment info - what's wrong?? I cannot get beyond that point. when i close the box the app-icon also disappeares

i used to be able to smoothly download free apps. suddenly, also free apps open a box that require my payment info. a message tells me that i did not finish a purchase. i cannot reset the whole thing and i am also not aware of a purchase i attempted. what can i do?

Check to be sure that you don't have something that never totally downloaded - look in iTunes and in iBooks as well - not only in the app Store. A stalled or incomplete download in one of the stores can cause problems with downloads in the other stores.
You can try to reset your iTunes account by signing out of the account and then signing back in. Restart the iPad in between signing out and signing in again.
Settings>Store>Apple ID-tap the ID and sign out. Restart the iPad. Restart the iPad by holding down on the sleep button until the red slider appears and then slide to shut off. To power up hold the sleep button until the Apple logo appears and let go of the button. Go back to Settings>Store>Sign in.

Roaming between two WiFi access points fails

Hi...
I just bought a Hawking WiFi range extender...a device that acts like a second wireless access point for rooms that are far from your wireless router. It's also known as a repeater. It has the same SSID (network name) as the one set up by the router.
You are supposed to be able to move about the house and you will connect to whichever device has the higher signal strength, transparently, with no hiccups, like moving your cell phone from one cell antenna to another.
The setup works fine with my Dell laptop, but not with my MacBook Pro or my iPad. When I change "zones", the Network locks up. This is repeatable and consistent.
I've heard rumors about Apple product difficulties with this "WiFi roaming."
Can anyone help?
Thx
Steve

I've been using a roaming setup in my home for years. The company I work for has building wide WiFi roaming setup with multiple WiFi access points on each floor. At home and at work, I frequently move my MacBook between access points without loosing things like my VPN, Screen Sharing, File Sharing, ssh terminal sessions, etc....
But 3rd party networking hardware has not always been well tested against Apple products. Many times 3rd party networking vendors test against some version of Windows and then ship it. Sometimes the 3rd party vendor offers a firmware update that corrects issues with Apple products.
At home I have Apple Airport Extreme base stations for my roaming setup. At work, the company is using Cisco commercial WiFi access points.
A roaming setup needs to have all WiFi devices on the same network "Subnet". That means a 2nd WiFi base station cannot act as a router, but must be just a bridge on the existing router's subnet (generally that means it cannot be offering DHCP services nor NAT services).
The 2nd WiFi base station must have the same SSID (as you said you setup).
And it must have the same security password using the same encryption algorithm (WPA2 preferred from a security stand point). You did not mention this, but I'll assume you did this as well.

AppleTV 2G as wireless access point

Hi, I thought of the possibility to turn AppleTV 2G as wireless access point when not in use as entertainment, there is an ethernet port and an integrated wifi connection, why not? Need only develop the right application ..

I'm tired of all these naysayers. Why don't you guys just go watch a movie with gw. That's what you want anyway. If the hardware is capable of it, OF Course its possible. Anything's possible really. Because you don't know how to do it does not make it impossible, it means you don't know how to do it. So, if this device can stream wirelessly in both directions hardware wise, some software would be able to make this happen. I'd check out iclarified.com. They have a section on Apple TV. All you would need to do is jailbreak it and have the right software to do it. Problem solved. Now was that so difficult? Baybeee

Photosmart c309a can't find access point to Mac Mavericks OS

I've owned probably ten HP printers. I've been thru five of them in five years and I'm beginning to think I need another brand. I have a 2010 Mac running Mavericks OS, a Netgear 802.11 wireless router, an Apple Air Port and Norton. I installed the c309a All-in-One printer last year for the first time. By spring of this year, the scanner function stopped working. The other day, the printer wouldn't print. I think the power plug might've come undone but I'm not sure. I selected a new print queue as I've done in the past and still no connection with the printer. I made sure connections were secure. No luck. I turned the printer off and restarted. Still nothing. I ran diagnostics: "Your HP printer cannot find your access point." The Network Name (SSID) was not found. I unplugged everything. I uninstalled the software, I reinstalled the software. Each time, the installation process would hang up at the configuration stage and the disc would spin and spin. I tried connecting via USB to my Mac, but that failed too. I rebooted my AirPort. I even tried to manually enter the IP address on the AIO keypad. No success getting the printer to recognize my Mac. I succeeded at making an ad hoc connection using the wireless radio with hpsetup as the SSID. The next day, when I needed to print, the hpsetup network option was unavailable and diagnostics told me the wireless radio wasn't working! Per online forum suggestion, [edited reset instruction by Moderator] That trick reset my wireless radio but still the c309a is unable to find my access point and I can't print using my 802.11 wireless. If I can't solve this problem, I will not buy another HP printer. I hope someone can help. Thank you for your time.

Hi @CluelessPackard ,
I see that you are unable to setup the printer over the wireless network. I would really like to be able to help you resolve this issue.
Restore the printer defaults.
Go to Setup, Network, Restore Network Defaults.
Print the Wireless Network Test.
Go to Setup, Network, Advanced Setup, Wireless Network Test.
If it passes, then it isn't a hardware issue with the printer.
If it passes, setup the Adhoc connection again.
Click the Airport on the top right corner on the Mac.
Click on the HP printer from the list. (you won't be on the internet till this procedure is finished)
Add the printer and try and print to see if the wireless is working properly.
Check the Configuration Page for the printer's IP address.
Go to Setup, Network, View Network Settings, Display Wireless Summary.
If you have a valid IP address for the printer then try and access the Embedded Web Server for the printer.
Type the IP address into your web browser's address bar. (Safari)
When setting up the printer, it has to be setup on the main router not the extension.
Go to the network tab along the top of the EWS.
Click on Wireless Setup Wizard along the left hand side to begin configuring the printer.
Apply your settings.
You have now completed the Wireless configuration.
Click the Airport on the top right corner on the Mac and select your network name.
Click on the Apple.
Click System Preferences, click the Printers and Scanners icon, then click the + sign, then select the printer from the list, make sure the printer listed beside use: shows the proper printer name, click on the add button. You might have to click on the drop down to select your printer.
Test the printer.
If you need further assistance, just let me know.
Have a wonderful day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Access point are not coming up after upgrade image of WLC

Hi,
I have AIR-WLC4402-50-K9 WLC i that current IOS is 7.0.98.218 and i upgraded with 7.0.116.0 IOS but after upgrading and reboot the WLC from 15 access point 3 access point are not coming up and 12 are coing up and working fine (4 1142 and 11 1131 series access point) 3 which are not coimg is 1131 series access point. when i login with console to 3 access point its rebooting 2 times and coming on ap: prompt.
In between that i reloaded the WLC one more time because from 15 acess point only 4 aceess point are came up and i also cleck the show boot on wlc its output is
7.0.116.0 (default)
7.0.98.218 (active)
so i reload the wlc and checked out of 15 acess point now 12 acess point are up and still 3 are not. And i also checked the output of show boot command its
7.0.116.0 (default)(active)
7.0.98.218
So i things its because of when 2nd time i reload the wlc the remaining 3 access point are getting image from wlc but because of reload its connection should be loss and error loading flash error are coming on acess point.
After that i recover the IOS for access point and convert into autonomus and from autonomus convert into Leightweight Access point. I also attached the procedure for recover the ios of access poing
But my question is why this 3 access point are not coming up is this happen's after upgrading wlc can any one please send me Step by Step WLC S/W Upgrade' process and if this this happens some time please send me any doccument related to this.

Sunil,
When you rebooted the controller did you do it from the Web GUI, the CLI, or did you physically reboot the controller? I believe and maybe incorrect but if your getting the ap: < prompt > that means that there is no firmware on the unit. If you have restored these to functioning autonomous unit and then re-converted them to Lightweight and it's still happening then we need to look at a debug output of what is happening when those AP's attempt to join the controller.
The capture you attached shows that it appears to join the controller and get a config, but are you saying that when it reboots again it stops working?? the other thing I would reccomend is clear out the flash memory since your capture shows the possibility that there are several copies stored there.
Hope this helps.

E61 - Cannot remember its access points when loose...

Similar Messages

Maybe you are looking for