EM (DB console) configuration after switchover

Hello Guys,
I have this scenario:
- Oracle 11.2.0.3
- RHEL 4.6 64 bits
- Active Data Guard
- Broker configured
- DBconsole configured on primary server
Now, I have server PRIM with the primary database, and server STB with the standby server. For now, the dbconsole is configured in the PRIM server.
When I do a switchover (to the standby on STB), EM is not configured, so I use RepManager.sh to clean the sysman user, and I use emca to recreate the dbconsole. After this, everything works.
Once I switch back, the EM is no longer configured on PRIM, so I repeat the previous steps (repManager and emca).
Everything is ok after this. I can access the EM on the primary normaly, and this gets information from the broker to provide basic information on the STB (like db status, apply, and so forth).
my question is this:
- do I have to do all these steps in case of a switchover? is there an easier way?
- would grid control solve this situation?
thanks guys,
br,
jpinela.

Pinela wrote:
Hello Guys,
I have this scenario:
- Oracle 11.2.0.3
- RHEL 4.6 64 bits
- Active Data Guard
- Broker configured
- DBconsole configured on primary server
Now, I have server PRIM with the primary database, and server STB with the standby server. For now, the dbconsole is configured in the PRIM server.
When I do a switchover (to the standby on STB), EM is not configured, so I use RepManager.sh to clean the sysman user, and I use emca to recreate the dbconsole. After this, everything works.
Once I switch back, the EM is no longer configured on PRIM, so I repeat the previous steps (repManager and emca).
Everything is ok after this. I can access the EM on the primary normaly, and this gets information from the broker to provide basic information on the STB (like db status, apply, and so forth).
my question is this:
- do I have to do all these steps in case of a switchover? is there an easier way?
- would grid control solve this situation?
thanks guys,
br,
jpinela.Its a Good question. While configuring EM it gathers all the information such as hostname, instance name, port number , listener and so many..
Of course configuration is not same on primary and standby, then EM configuration file properties mismatch with services after the switchover specifically if you are monitoring redo transport , apply and status so on....
AFAIK, you must reconfigure again whenever there is frequent changes. BTW, reconfiguring EM which takes minutes of time.

Similar Messages

SF300-24 is not saving configuration after reboot

Dear All,
I have a couple of SF300-24 switches. When I made needed configurations using CLI or GUI and then saved all configurations. The problem is that switches do not save configurations after reboot. Please assist.
Thank you in advance

Hi Vsevolod,
I guess you have performed the function to copy the running configuration to the startup configuration as per the screen capture below.
The current released version of code does not have a supported CLI only a menu accessable via console, SSH or telnet. New code coming out this month supports a CLI, so I am surprised by your comments regarding CLI.
If you have a early beta release of software version 1.1 with CLI, I would suggest you call into the Small Business Support Center to get the problem looked at.
I am using the beta code on my ten port SG300 and 48 port SF300 , but had no difficulty saving configurations in old or beta versions of firmware.
If you are still having trouble after reading this post, please contact the SBSC at ;
http://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html
regards Dave

How to use custom pipeline dlls in Biztalk Projects so that they appear in the send/receive pipeline configuration after deployment?

I have a existing Biztalk application that uses custom pipelines for receiving excel files. I have the dll of that custom pipeline. Now i created another BT application that needs to use that same custom pipeline. But after i deploy the application in
Biztalk, i can't see the pipeline available in Receive pipeline configuration combo box during configuration. I have referenced the custom pipeline dll in my project before deploying, but that doesn't help. I also copied the dll in the C:\Program Files
(x86)\Microsoft BizTalk Server 2010\Pipeline Components folder and C:\Program Files (x86)\Microsoft BizTalk Server 2010 folder, but that doesn't make the pipelines appear during configuration too.
Can anyone give any idea on how can i use these custom pipeline dlls in project so that they appear in configuration after deployment?

If you plan on using the deployed pipeline across multiple applications in BizTalk, the BizTalk Application (using the BizTalk Server Administration Console) should have the other application [where the pipeline is deployed] as reference.
For e.g.: Custom Pipeline (myCustomPipeline) part of a BizTalk Project (dll - myCustomProject.dll) deployed under Application [Some Application] also to be used in another BizTalk Application [Some Other Applicaiton] then using BizTalk Server Administartor
right click the "Some Other Application" and select "Properties"
on the "Properties" page, left hand side, select "References"
on the right-hand side, use "Add" to add the "Some Project" as a reference.
Doing so will ensure that ALL resources (maps, schemas, orchestrations, send ports, receive locations, rules, etc.) deployed for "Some Application" are available/referensible in "Some Other Application".
Regards.

HT1766 I cannot complete my iphone configuration after sofware update, when i connect to itunes i keep gettin a try again later message

I cannot complete my iphone configuration after sofware update, when i connect to itunes i keep gettin a try again later message

That's usually a sign that your phone was hacked/jailbroken, and iTunes has detected such, errored out, preventing your phone from activating. Since Apple does not support hacking/jailbreaking, that's what happens, by design.
We can't help you here, as Apple owns this forum. You'll have to go elsewhere.

Can I reconfigure iPads using Apple Configurator after previously being setup with iTunes?

Can I reconfigure iPads using Apple Configurator after previously being setup within iTunes?
Will VPP Codes be able to be reused? Can I restore to a backup made in iTunes?

Can I reconfigure iPads using Apple Configurator after previously being setup within iTunes? Yes.
Will VPP Codes be able to be reused? From iTunes - No.
Can I restore to a backup made in iTunes? You can back up an iPad that was set up in iTunes in Configurator and use that as back up in Configurator.

Cannot save the configuration after zone changing.

The customer is trying to save the configuration after a Zone changing. The error message is the following:
# copy running-config startup-config
2008 Oct 10 13:22:45 SW1SU %ZONE-2-ZS_INIT_FAILED: Failed to save persistent configuration
2008 Oct 10 13:22:45 SW1SU %ZONE-2-ZS_INIT_FAILED: pss_create failure, code = 0x8048001e, URL = sync:/mnt/pss/zone_zs_active_zset_cfg
2008 Oct 10 13:22:45 SW1SU %SYSMGR-2-CFGWRITE_ABORTED: Configuration copy aborted.
Configuration update aborted: request was abort
or
#copy running-config startup-config
2008 Oct 10 13:22:45 SW1SU %ZONE-2-ZS_INIT_FAILED: Failed to save persistent configuration
2008 Oct 10 13:22:45 SW1SU %ZONE-2-ZS_INIT_FAILED: pss_create failure, code = 0x8048001e, URL = sync:/mnt/pss/zone_zs_active_zset_cfg
Does someone has any idea how to solve this problem?

The root cause is the compact flash card. There was a software fix attempted in 3.0.2 but is not 100%. If the problem shows up again, the reload will clear it, but the ultimate fix is to replace the compact flash card with a new one. In some instances, based on your service provider, this may be a complete chassis replacement. This requires license re-homing as licenses are tied to the chassis serial number. I believe it has to do with the number of writes to the CF card. At some point, the card goes into a read only state and reload is the only option to clear it.

I have added two new extension on CUCM, Directory not showing in attendant console even after resynch on CUCM and attendant cosn

I have added two new extension on CUCM, Directory not showing in attendant console even after resynch on CUCM and attendant cosnole
Any idea?

Hello,
Can you tell us what versions of CUCM and CUxAC you are using? Just extensions alone in CUCM will not sync to the corporate directory within the attendant console application. You will at least have to have user's associated with those extensions and depending on your rule set within the console that should then bring those extensions into the console directory.
Thanks,
Tony

Propagation after switchover to standby

Hi
My DB Version=10.2.0.4
I had a stream relation that working correctly after switchover to standby in destination now in source database i got the following error in propagation:
select status,error_message from dba_propagation
DISABLED
ORA-02068: following severe error from AQHOS
ORA-01033: ORACLE initialization or shutdown in progress
ORA-06512: at "SYS.DBMS_AQADM_SYS", line 1087
ORA-06512: at "SYS.DBMS_AQADM_SYS", line 7616
ORA-06512: at "SYS.DBMS_AQADM", line 631
ORA-06512: at line 1
i corrected all tnsnames and dblink is working correctly but still i have this error.
WHAT I MUST TO DO?

Refer to metalink document _STREAMS propagation to Primary of physical Standby configuation errors with Ora-01033, Ora-02068 *[ID 359971.1]*_
You need to set SERVICE_NAMES. Hope this helps resolve your issue.
Thanks

Cisco 2611 loosing configuration after router restart

Hello,
I have a router at a customer that looses its configuration after a restart.
I of course made a write mem, and it looks like this has been before.
Is there anything to check (hard/soft) befoire changing the router?
thanks in advance
Pierre Barrat

Check to see the configuration register value. You can do that by issuing the command 'show version'. At the bottom of the output of the command you will see the config-register value. Under normal circumstances this value should be 0x2102. If you see something like 0x2142 it means that the router is going to ignore the start-up configuration.
If the config-register value is indeed incorrect then you need to change it to 0x2102 by:
Router# copy start run
Router# config t
Router(config)# config-register 0x2102
Router(config)# exit
Router# wr mem
Router# reload
After the reload it should come up with the right config; that is if the problem was indeed with the configuration register.

Directory Server Admin Console "disappears" after logging in

Hi,
We are just starting to work with Directory Server 6.1, on RedHat 4. I access the server on which Directory Server is running via X. However, when I try to access the Admin Console and after logging in, the main Admin Console panel appears very briefly, and then everything, including the xterm window that I started with, disappears.
I've tried restarting both the slapd (slapd-xxx) and admin console (start-admin), but the same thing keeps happening.
This is the first time that I'm working with 6.1, but do I need to login/start the Admin Console a different way than before when using X?
Thanks,
Jim

Hi,
No one has responded to this thread, but for the record, one of my colleagues got it working today, and I hope that this info might help someone else someday...
I had neglected (sorry) to mention that we're in an environment where we can't run directly as root, but instead have to use sudo.
What I was doing earlier was ssh'ing to the server, then doing a "sudo bash", doing the "export DISPLAY=...", then running the startconsole to startup the Sun DS console.
So, today, I was fooling around with this with one of the other guys, and instead of doing the "sudo bash", he just did the "export DISPLAY=...", and then just "sudo ./startconsole", and, voila, we got the console GUI and were able to login without it disappearing.
I had not tried that previously, because I had thought that the "export DISPLAY=..." wouldn't have survived the sudo (I'm not that familiar with it), but I guess it does.
I'm not 100% sure what the problem was with doing the "sudo bash", but I believe it had something to do with "who we were logged-in as".
Maybe someone here who's more familiar with sudo, etc. and Cygwin X might be able to provide an explanation.
Jim

Db console configure !!!!

Hi
Edited by: LazyDBA10g on Mar 9, 2009 2:54 AM

Why are You posting duplicate threads?
db console configure !!!!
Here is the same question from You and 2 answers already provided. Some issues or more errors appeared during configuration?

Configure after sales service product

hello gurus,
can somebody guide me how to configure after sales service of a product sold say for eg truck and i want to know how do we connect the same with the order delivered.
specific and detailed write up would be better for an understanding perspective,
somebody reply/help
thanks
Message was edited by:
varada rajan
Message was edited by:
varada rajan

Thank you for visiting the HP Support Forums. I'm sorry but this is a peer-to-peer community of HP customers, and not a venue to contact HP directly. Most of the users here are consumers like yourself who are offering solutions because they like to help others, and any HP employees you see are here on their own capacity and not representing the company.
If you have additional or direct feedback for HP about their products or services, or questions about repair, you can use the link below for contact information.
http://www8.hp.com/us/en/contact-hp/ww-contact-us.html
If you have other questions and concerns about using the forum, please feel free to send me a private message.
OrnahP
HP Support Forums Moderator
Clicking the "Kudos Star" to the left is a great way to say thanks!
When your problem has been solved, accept the solution by clicking "Accept as Solution" to help other members in the future!
Rules of Participation

Save configuration after fixing discrepancies with CM.

How can I save running configuration after fixing discrepancies?
Thanks.
Regards.
Andrea

Sounds good!
I'm looking for a flag or application setting on Campus Manager to save configuration. After a fix runnnig and startu are out of sync.
Thanks.
Regards.
Andrea

Websites were deleted from configuration after Maverick OSX Server Update

Websites were deleted from configuration after Maverick OSX Server Update. My subversion access was also overwritten and no longer works.

if that was a bug report, then Apple might or might not see it here. There's a Provide Server Feedback in the menus of Server.app, if you'd like to let the Server.app folks know about the upgrade problems I've encountered.
If you're looking for help resetting the web sites (I'm not clear if you're reporting a bug or looking for help with this), then check Server.app for where the files should be (the default location is under /Library/Server/Web/Data directory) and see where your current sites are stored in the file system, establish the Site via Server.app (usually with a directory under the /Library/Server/Web/Data path) and move the contents over to the new location.
As for the Outlook comment in your footer, Microsoft Outlook also generally needs to have the FQDN requirements removed in the SMTP HELO processing. Outlook doesn't send that, and the default Postfix configuration will reject those connections as spam. Here's a discussion of how to do this. (I don't see a path to the HELO processing via sudo serveradmin settings mail:postfix commands.)

Loosing Plug in configuration after restart

I am loosing always my plug in configurations after a restart of my PC.
How can I solve this?
Jürgen

Are you saying that each time you restart Elements the files are shown missing again? This is strange, you can try Catalog Recover by selecting File->Catalog->Recover option and see if that helps.
-Smriti

EM (DB console) configuration after switchover

Similar Messages

Maybe you are looking for