Error like process ovedue in extraction data
hai bw gurus,
when ever i extracted the data i facing the process overdue problem
is there any i have done wrong
plz let me know
regards,
murali
Hi Murali,
as already suggested in the past in these forums, there can be several causes:
- has ALL relating master data already been loaded into your system ?
- check parameter settings of the database (since incorrect parameters can have a significant influence on the performance)
- not so optimized ABAP code (routines in BW or exits in R/3)
- data package settings (keep the number of data IDocs small...SBIW -> General settings -> Control parameters for data transfer)
- set the value for Max.Perc. equal to the number of batch processes in the system
- delete an re-create your cube indexes (if applicable)
Let me know where your problem arises !
In the meanwhile, hope it helps!
Bye,
Roberto
Similar Messages
-
Error in Process Chain while extracting data from source system
Hi All,
Dail we are facing problem while retrieving the data from source system for the data source 0TB_AMOUNT1 in the process chain, it is giving error "Function module BANK_TMC_API_SIM_GET does not exist Furnction module". when I repeat the step than it is going fine.
Please let me know why this error is coming for first why it is not coming after repeating the step?
Thanks & Regards,
Murali.Hi Murali,
Hope you are doing good..
Is it a full or Delta load on a daily basis? Did you check if the FM exists in your system?
Did you try debugging the load in source system and check if the extractor is trying to call FM you mention.
If possible please post the exact error message you are receiving so that we could get an idea whats the error and why you are encountering it.
As of now what i can suggest is, go to RSA2 in source system, give the datasource name and check if the extractor code has FM in it.
Regards,
Anil Pragada. -
Hi,
Two month before, We have deployed Lync 13 set up with lync monitoring and archiving service enabled. After configuring we have the Lync monitoring and archiving services are working fine... few weeks back I have changed the Admin Password
of the Lync Setup. After that Lync Monitoring and Archiving services are not working.
when I try open Lync monitoring service from web UI,
http://localhost/ReportServer_LyncMonitoring/
Web UI is opening but Reports home page is not Accessible , Getting error Like
"An error has occurred during report processing. (rsProcessingAborted)
Cannot impersonate user for data source 'CDRDB'. (rsErrorImpersonatingUser)
Log on failed. Ensure the user name and password are correct. (rsLogonFailed)
The user name or password is incorrect"
Please help me to trouble shoot this problem.
Thanks,
Rajarajan.DHi Rajarajan.D
You probably need to update the password against the CDRDB datasource in SSRS Report manager, take a look at this article: http://lyncme.co.uk/microsoft-lync-server-2013/cannot-impersonate-user-for-data-source-cdrdb-rserrorimpersonatinguser-error/
If this helped you please click "Vote As Helpful" if it answered your question please click "Mark As Answer"
Georg Thomas | Lync MVP
Blog www.lynced.com.au | Twitter
@georgathomas
Lync Edge Port Check (Beta)
This forum post is my own opinion and does not necessarily reflect the opinion or view of Microsoft, its employees, or other MVPs. -
Error in process chain - 0COORDER_ATTR master data
Hi,
I tried to load the attributes for 0COORDER_ATTR and receive the following error message for all data lines:
Diagnosis
Data record 1 & with the key '000006002991 &' is invalid in value
'11-ES-US-0040-INV# &' of the attribute/characteristic 0PROJECT &.
System Response
The system has recognized that the value mentioned above is invalid, and
has processed this general error message. A subsequent message may give
you more information on the error. This message refers to the same
value, even though it does not state this explicitly.
- i have found in RSA3 that the data for that particular project is same as above.
SO do i need to correct at R3 level or at PSA level?Hi,
Check the below link (logic to write a routine for removal of Invalid char)
https://wiki.sdn.sap.com/wiki/display/BI/HowtoremoveInvalidcharacters
in transformation select a particular char and use the rule type as routine and use the above logic ,
This would be the permanent logic to avoid the error .
Regards,
Satya -
Error while Extracting data using RSCRM_BAPI
Friends
We are on 3.5 system upgraded recently. I am getting the following Error message while trying to extract data from a query to a table using the transaction RSCRM_BAPI. The Error message says ' Internal Error in Method CHECK_TABLE_NAME(RSCRMBW_EX_NAMESPACE_GET).
This was working fine prior to upgrade. I scoured all the OSS notes, could not find an appropriate one to solve the issue.
Have you had this problem and any thoughts on resolution ? Appreciate your inputs very much.
Regards
Mathur SreedharHi Mathur,
did you ever resolved this Issue? if so can yoou share with me the solution. i am having the same problem, we are in 3.0 . it works fine in Development and Test. but when i try it in Production . i get this error.
'Internal error in method CHECK_TABLE_NAME (RSCRMBW_EX_NAMESPACE_GET)..
if you know the answer. would please share with me.
your help would be greatly appreciated.
Thanks.
Sreeni. -
Hi Experts,
I got an exception error when process reassignments for key date results(transaction code /BA1/FG_PR_KR_REASS) in BANK ANALYZER, did anyone get the same problem before? any solutions?
the process sequences is listed below:
1,,Set SDL Timestamp,, /BA1/B0_CLOSE_SDL
2,,Generate Positions,, /BA1/F2_PB_PR
3,,Aggregate Financial Transactions,,,, /BA1/FG_PR_FT
4,,Prepare Business Transactions for Aggregation,, /BA1/FG_PR_BT_PRE
5,,Process Reassignments for Business Transactions,, /BA1/FG_PR_RABT
6,,Aggregate Business Transactions,,/BA1/FG_PR_BT
7,,Process Reassignments for Key Date Results,, /BA1/FG_PR_KR_REASS
7.a),,Subcomponent view,,subcomponent=S_SVAC01 ,,OK
7.b),,Subcomponent view,,subcomponent=S_SVFT01 ,,Exception
I nenver changed subcomponent settings, they are all SAP delivered.
Exception CX_SY_NO_HANDLER: An exception with the type
CX_SY_MOVE_CAST_ERROR occurred, but was neither handled locally, nor
declared in a RAISING clause
Message no. /BA1/AL_X0_M_H000
Exception CX_SY_MOVE_CAST_ERROR: Source type
\CLASS-POOL=/BA1/CL_AL_FG_MD_SUB_CMP_VIEW\CLASS=LCL_SCV_FT2AGGRO is not
compatible, forthe purposes of assignment, with target type \INTE
Message no. /BA1/AL_X0_M_H000
Thanks!Hi Abhi,
in do_prepare_output you are getting mixed entity which is combination of bol entity and value node.
you can get the bol entity from mixed node by calling a method get_model_node similarly to get value node entity get_value mode method is available check the class CL_BSP_WD_MIXED_NODE methos, you will get an idea.
Cheers,
Sumit Mittal -
Problem Extract Data from Essbase
Hi all,
I have this error when I try to extract data from essbase :
org.apache.bsf.BSFException: exception from Jython:
Traceback (innermost last):
File "<string>", line 1, in ?
com.hyperion.odi.essbase.wrapper.EssbaseRecordFetchException: Out of memory error.
at com.hyperion.odi.essbase.wrapper.EssbaseReportDataIterator.hasNext(Unknown Source)
at com.hyperion.odi.essbase.ODIEssbaseResultSet.next(Unknown Source)
at com.hyperion.odi.essbase.ODIStagingLoader.loadData(Unknown Source)
at com.hyperion.odi.essbase.AbstractEssbaseReader.extract(Unknown Source)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
For information :
I use an reportscript which extract 400 000 records. I think that the problem comes from the staging area. How to modify size of the management of the memory?
I don't have this problem when i extract just 2 000 records for exemple.
Best regards,
BenHi,
Are you using a local or a defined agent?
Are you using the memory engine as the staging area.
Anyway you can increase the memory being used by the JVM depending on the above.
Cheers
John
http://john-goodwin.blogspot.com/ -
Hi guys,
I'm usinf BOE 3.1. I have a problem during extraction data from R3 to *.dat file. The error is is File
skb\STG1_FT_DAY_PP_PRODUCTION.dat cannot be opened. Job cancel after exception error. For you info my folderfor all *dat file is in SAP DB server (IBM server). from sap server we ftp *.dat file to BO server (HP Server).
The problem is sometime different file occured. Actually i've already post this issue to OSS, i've already follow their suggestion but still problem. Is that any setup in SAP SB server ? One more thing i success extract the data in QAS server.
I hope somebody can guide me and help me how to solve this issue.
Thank You.
Regards
-akma-HI,
just to clarify: in the BusinesObjects Enterprise system you not storing data.
1. ECC - > SAP BI(back-end) for storing ECC and other legacy data->BO reporting tools like Crystal Reports, WebI, Xcelsius etc.,
>> for sure possible
2. ECC -> BO(back-end) for storing ECC and other legacy data using DI for setting up the ETL process -> BO reporting tools like Crystal Reports, WebI, Xcelsius etc.,
>> you would then use something that is called a Rapid Mart for example
3. ECC ->use BI and BO as back-end system -> BO reporting tools like Crystal Reports, WebI, Xcelsius etc.
>> yes.
Both backends have a different purpose. BusinessObjects is reporting and BW is a datawarehouse.
Ingo -
How to extract data from multiple tables (always got errors)
Dear Experts,
I have a simple mapping to extract data from multiple tables as a source (A, B, C) to a target table (X). Below is the picture:
(Sources)....(Target)
A----------------***
B----------------X
C----------------***
Sample Source Data:
Table A:
ColA1
100
200
etc
Table B:
ColB1 ColB2 ColB3
10 Y Ten
20 Y Twenty
30 Y Thirty
etc
Table C:
ColC1 ColC2
11
12
13
etc
Target table (X) should be (just has 1 group INGRP1):
ColA1 ColB1 ColB3 ColC1
100 10 Ten 11
100 10 Ten 12
100 20 Twenty 21
etc
Scenarios:
1. Directly map from A, B, C to X. Unable to map with error message: "API8003: Connection target attribute group is already connected to an incompatible data source. Use a Joiner or Set operator to join the upstream data first before connecting it into this operator."
2. Map each source to Expression Operator and then map from each Expression to target table. I am able to map all attributes successfully but got error when validating it with message: "VLD-1104: Attributes flowing into TEST.EXPR_SRC.INGRP1 have different data sources."
How can I achieve the correct mapping for this purpose?
Use Joiner? I have no key to join the sources
Use Set? The sources have different number of columns
Thanks in advance
PratThanks Nico,
I think it will results data like this:
100 10 Ten 11
200 20 Twenty 12
300 30 Thirty 13
etc
and not the expected:
100 10 Ten 11
100 10 Ten 12
100 20 Twenty 21
etc
But it inspired me to solve this by adding key expression in each source table (B & C) to be joined to table A with this formula:
100+TRUNC(INGRP1.COLB1,-2)
Regards
Prat -
Error 8 when starting the extracting the program-data load error:status 51
Dear all,
<b>I am facing a data exracton problem while extracting data from SAP source system (Development Client 220). </b>The scenario and related setting are as the flowings:
A. Setting:
We have created 2 source system one for the development and another for the quality in BW development client
1. BW server: SAP NetWeaver 2004s BI 7
PI_BASIS: 2005_1_700 Level: 12
SAP_BW: 700 Level:13
Source system (Development Client 220)
2. SAP ERP: SAP ERP Central Component 6.0
PI_BASIS: 2005_1_700 Level: 12
OS: SunOS
Source system (Quality Client 300)
2. SAP ERP: SAP ERP Central Component 6.0
PI_BASIS: 2005_1_700 Level: 12
OS: HP-UX
B. The scenario:
I was abele to load the Info provider from the Source system (Development Client 220), late we create another Source system (Quality Client 300) and abele to load the Info provider from that,
After creating the another Source system (Quality Client 300), initially I abele to load the info provider from both the Source system , but now I am unable to load the Info provider from the (Development Client 220),
Source system Creation:
For both 220 and 300, back ground user in source system is same with system type with same authorization (sap_all, sap_new, S_BI-WX_RFC) And user for source system to bw connection is dialog type (S_BI-WX_RFC, S_BI-WHM_RFC, SAP_ALL, SAP_NEW)
1: Now while at the Info Package : Start data load immediately and then get the
e-mail sent by user RFCUSER, and the content:
Error message from the source system
Diagnosis
An error occurred in the source system.
System Response
Caller 09 contains an error message.
Further analysis:
The error occurred in Service API .
2:Error in the detail tab of the call monitor as under,
<b>bi data upload error:status 51 - error: Error 8 when starting the extracting the program </b>
Extraction (messages): Errors occurred
Error occurred in the data selection
Transfer (IDocs and TRFC): Errors occurred
Request IDoc : Application document not posted (red)
bw side: status 03: "IDoc: 0000000000007088 Status: Data passed to port OK,
IDoc sent to SAP system or external program"
r<b>/3 side: status 51: IDoc: 0000000000012140 Status: Application document not posted
Error 8 when starting the extraction program</b>
Info IDoc 1 : Application document posted (green)
r/3 side: "IDoc: 0000000000012141 Status: Data passed to port OK
IDoc sent to SAP system or external program"
bw side: "IDoc: 0000000000007089 Status: Application document posted,
IDoc was successfully transferred to the monitor updating"
Have attached screen shots showing error at BW side.
check connection is ok, tried to restore the setting for bw-r3 connection though same problem
Have checked partner profile.
<b>what's wrong with the process? </b>
Best regards,
dushyant.Hi,
Refer note 140147.
Regards,
Meiy -
Error while extracting data from datasource 0GLACCEXT_T011_HIER in RSA3
Hi Experts,
While trying to extract the data for the datasource 0GLACCEXT_T011_HIER in RSA3, am getting the below Dump.
Runtime Errors SAPSQL_ARRAY_INSERT_DUPREC
Except. CX_SY_OPEN_SQL_DB
Short text
The ABAP/4 Open SQL array insert results in duplicate database records.
What happened?
Error in the ABAP Application Program
The current ABAP program "SAPLFAGL_FSV" had to be terminated because it has
come across a statement that unfortunately cannot be executed.
Error analysis
An exception occurred that is explained in detail below.
The exception, which is assigned to class 'CX_SY_OPEN_SQL_DB', was not caught
in
procedure "FSV_TEXTS_CONVERT" "(FORM)", nor was it propagated by a RAISING
clause.
Since the caller of the procedure could not have anticipated that the
exception would occur, the current program is terminated.
The reason for the exception is:
If you use an ABAP/4 Open SQL array insert to insert a record in
the database and that record already exists with the same key,
this results in a termination.
(With an ABAP/4 Open SQL single record insert in the same error
situation, processing does not terminate, but SY-SUBRC is set to 4.)
Kindly help me out in resolving this error.Hi,
This dump occurs if the storage of original files is not happening in a Content Server, which is recommended by SAP. You can check this easily if you go to transaction DC10 and check if the flag 'Use KPRO' is set for the used document type.
SAP do not recommend storing such larger files in SAP DB. If you try to store any original in the SAP DB, the file will be stored in the table DRAO. That means you are consuming table space memory. For one original we can have maximum of 9999 rows in the table. To store larger originals in SAP DB more than 9999 rows in the table are needed and this is not possible. That's the reason behind this dump. Storing such huge files inthe SAP DB will also affect the performance of the system while accessing the original
Refer the thread
"http://wiki.sdn.sap.com/wiki/display/PLM/SAPSQL_ARRAY_INSERT_DUPRECwhilesaving+original"
Thanks, -
Error in source system while extracting the data from R/3!
Hi,
i had created FM and extract strcucture in R/3 .
using the above two, i had created data source using RSO2 T code.
when i checked the extractor ( RSA3 T code) in R/3 it was working fine .
(status messege displayed as 1000 records selected).
then i assigned this data source to infocurce and creted info cube using the same info source.
but when i schedule the info package it is syaing in the monitor screen "error in source system".
what could be the problem?
Thanks,
RaviHi
trhese are the possiblies
1.first check the source system connection and find if there is any error in it.
2.Go to sm37 and find whether the request is completed or not if its terminated find out the time. how long does it takes to complete the process.
3.once again relicate the data source and find whether is it again extract data. -
Error while extracting data from CRM
Dear all,
I have used some standard and generic datasources to extract data from CRM. These were working fine for more than a year and are scheduled in Process chains. For the past few days I am getting Caller 09 error as shown below, only for the generic datasources. I have checked the connection,replicated the datasources and activated them, reinitialized and have tried all the solutions that were posted earlier, but still the process chain fails. When I execute the process chain for generic datasources manually, it is working fine.
When I tried in RSA3 for both standard and generic datasources in CRM with update mode D, I get a message 'Error occured during the extraction',
Kindly suggest what can be the problem.
Error message from the source system
Diagnosis
An error occurred in the source system.
System Response
Caller 09 contains an error message.
Further analysis:
The error occurred in Extractor .
Refer to the error message.
Procedure
How you remove the error depends on the error message.
Note
If the source system is a Client Workstation, then it is possible that the file that you wanted to load was being edited at the time of the data request. Make sure that the file is in the specified directory, that it is not being processed at the moment, and restart the request.
Thanks all in advance.
Regards
Adhira AnandHi Meyappan,
I have checked SM37, SM21 and ST22. There are no errors.
in SM37 the below log is displayed.
Job started
Step 001 started (program SBIE0001, variant &0000000005420, user ID ALEREMOTE)
Asynchronous transmission of info IDoc 2 in task 0001 (0 parallel tasks)
DATASOURCE = ZCRM_SRV_DEFECT
RLOGSYS = CLNT645BIP
REQUNR = REQU_4JHQ8HH6KA40JHC1TYLYIV2W2
UPDMODE = D
LANGUAGES = *
Current Values for Selected Profile Parameters *
abap/heap_area_nondia......... 2000000000 *
abap/heap_area_total.......... 2000000000 *
abap/heaplimit................ 40000000 *
zcsa/installed_languages...... DE *
zcsa/system_language.......... E *
ztta/max_memreq_MB............ 2047 *
ztta/roll_area................ 6500000 *
ztta/roll_extension........... 2000000000 *
1 LUWs confirmed and 1 LUWs to be deleted with function module RSC2_QOUT_CONFIRM_DATA
IDOC: Info IDoc 2, IDoc No. 101415, Duration 00:00:00
IDoc: Start = 13.10.2010 22:51:39, End = 13.10.2010 22:51:39
Synchronized transmission of info IDoc 3 (0 parallel tasks)
IDOC: Info IDoc 3, IDoc No. 101416, Duration 00:00:00
IDoc: Start = 13.10.2010 22:51:42, End = 13.10.2010 22:51:42
Job finished -
Error in process chain (psa data)
We have got an error in our PROCESS chain for master data.
Info object Name : 0customer
In that it was showing there was error in our request. When I wanted to correct data in the request there it was showing no error records. All the records are good and also it is showing as error in request. I have deleted the request from infoobject and also from the PSA. And the last updated good request is also showing error as No data packets available for the request .
0Customer is delta update ; Process chain is daily based.
My doubt is whether the records in the deleted requests will be reloaded again from sap R/3 into PSA, as requests during Process chain or not.
While monitoring the request details in Monitor u2013 Administrator Work bench, it shows the following:
1. Requests (messages) Everything Ok
2. Extraction (messages) Missing messages
3. Transfer (IDocs and TRFC) Missing messages
4. Processing (data Packet) No data
5. Process chains : Everything Ok.
Even after deleting the requests my process chain is not getting updated.
Kindly help me in solving the above problem
Regards
PadmaHi,
Once deleted the request, try to manually trigger the load and see whether it completes. if it completes and pulls reocrd then you can push the chain process ahead with the program RSPC_PROCESS_FINISH
Regds,
Shashank -
Error while extracting data from a remote system
Hi,
I am facing problem while extracting data from a remote system. The connection is alright I can extract the table required from the remote system,but when I deploy it I get this error
ORA-04052: error occurred when looking up remote object [email protected]@ORACLE_UBN_15_LOCATION1
ORA-00604: error occurred at recursive SQL level 1
ORA-28000: the account is locked
ORA-02063: preceding line from UBNDW@ORACLE_UBN_15_LOCATION1
here Scott.demo1 is the table and UBNDW is the sid of the remote system and ORACLE_UBN_15_LOCATION1 is the location. Please help me out with this
ThanksHi,
IDOC's need to be processed manually either in OLTp or in BW depending on the failure. Error msg in monitor status will take u to either BW or OLTP whernever there is a prob. Process IDOC's , this will start the left over packets and will finish the load.
we hav to check IDOC in WE05(t-code) and know the status these are WE51,WE52,WE53 AND GOTO WE19 there we hav to execute the exist Idoc will succesfully loaded Idoc
Goto St22 see the short dump error msg..
post if there any inf..
Thanks,
Shreya
Maybe you are looking for
-
GR no is not getting updated in CNS0
Dear Experts, While doing cns0 transaction BDC , i need to update the GR no in likp table. In CNS0 T-code where should i update the GR no of the material. (My input - WBS element, Project, Material, Quantity and GR No) In VL02N in the shipment tab (
-
Why is ichat "DONE" button missing?
I'm trying to set up a computer with ichat and when I get to the final screen it states on the buttom of the window: *Click Done to start using ichat* but the Done button is missing. When I click the blue Continue button nothing happens. I'm stumped
-
QuickTime MPEG-2 Component cant playback High Profile High Level content
Is the QuickTime MPEG-2 Playback Component really unable to playback HP HL content? Im encoding high bitrate media content to mediaservers with my Mac Pro and have used VLC so far to playback the encoded files. VLC however doesent loop flawlessly so
-
Change file name when sending form through email
Hi all, I created a form that can be downloaded, viewed and completed by the user in Acrobat reader, and then sent by email as a pdf-attachment by pushing a submit-button. As the form will be sent by several different users to the same address, in or
-
Is their roadmap for the next major release of Netweaver stack?
In the ERP area, I found this link that mentions a roadmap for mySAP ERP2005 and beyond. Is there a corresponding "beyond NW04s" roadmap? Or is the next major release of Netweaver targeted for 2010 as is the next major mySAP ERP release mentioned in