Error message in adapter engine, can u solve it

Hi Gurus,
I am facing problem when invoking webservice through XML Spy, its showing the following error:
<b>com.sap.aii.af.ra.ms.api.DeliveryException: XIAdapterFramework:GENERAL:com.sap.aii.af.ra.ms.api.DeliveryException: Database connection could not be established
     at com.sap.aii.adapter.xi.ms.XIEventHandler.onTransmit(XIEventHandler.java:451)
     at com.sap.aii.af.ra.ms.impl.core.queue.CallConsumer.onMessage(CallConsumer.java:125)
     at com.sap.aii.af.ra.ms.impl.core.queue.Queue.run(Queue.java:831)
     at com.sap.engine.frame.core.thread.Task.run(Task.java:64)
     at com.sap.engine.core.thread.impl5.SingleThread.execute(SingleThread.java:79)
     at com.sap.engine.core.thread.impl5.SingleThread.run(SingleThread.java:150)</b>
Can anyone please tell why it will come and when it will come..
Give me suggestion how to solve this issue.
step by step procedure will be appreciated..
Thanks & Regards.,
Pushparaju.B.

Hi Ashutosh,
is your scenario like SOAP to JDBC?
in that case make sure that you have correctly loaded the jdbc driver followin this link:
<a href="https://webservice.sdn.sap.comhttp://www.sdn.sap.comhttp://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/3867a582-0401-0010-6cbf-9644e49f1a10">How To Install and Configure External Drivers for the JDBC & JMS Adapters</a>
Hope this help
Francesco

Similar Messages

Automatic restart of Error-Message in Adapter-Engine (Job?)

Hi,
we are working on PI 7.11 and facing following problem:
Often in message-monitoring error-messages are forgotten because of wrong date-selections by the monitorer (not enough days back). It would be very nice, if there is a function witch is repeating error-messages in adapter-engine automaticly and witch can be scheduled.
Does anybody know something about an excisting program / function on PI?
Regards
Jürg

Hi,
By default if any failure occurs in adapter engine (in case of receiver,during delivery to target system)
it will retry 3 times after a period interval of 5 minutes..this is by default even this can be change if needed with the help of the proeprties at NWA/VA...
but in case of failures at IE level (mappings,...) then you need to schedule the report RSXMB_RESTART_MESSAGES....
search SDN if like to know more about the reports...
HTH
Rajesh

Strang problem when searching error message in Adapter Engine

Hi all,
In RWB message monitoring, I tried to search all the error messages for yesterday and got no results. But I know there were actually several error messages for yesterday because I got several alert mails.
Then I went to my mail box and copy the message id and used it to search again. Then I found this message was exactlly in "System Error". But if I search all the error messages for yesterday, I get no results.
Anyone knows the problem?
Regards,
Hui

Hello Hui Wang,
<b>Adapter engine resides on Java stack and u view sxmb_moni on the ABAP stack which displays only Integration Server related errors.</b>
Message that passes the Integration pipeline are visible in sxmb_moni. Errors related to CC can be traced in CC monitoring or adapter monitoring in RWB.
With Regards,
Vidya
**************PLEASE REWARD POINTS IF FOUND USEFUL

Unable to cancel messages in adapter engine

Hello,
We have implemented an interface with file connector. Since one week, all messages are hanged in the adapter engine with status TO BE DELIVERED.
I tried to cancel but the folowing error message appears :
Could not fail message. Reason: com.sap.engine.interfaces.messaging.api.exception.MessagingException: Could not fail message 0013211d-2dc8-1def-a8a4-938b4635c3af(INBOUND), as triggered by admin action. Reason: Predecessor not in final state.
This interface is a proxy from ECC6-->csv file and i can't see the corresponding messaging in any queues SMQ1..
They are only available in the RWB/message monitoring/adapter engine
Can you tell me how to process these messages or cancel ?
Regards

Hi
Messages will go in to the state Tobe delivered if there are no threads available for the particular adapter.. and lack of threads is due to the state of the messages in DLNG...
Check the messages which are in DLNG and the reason behing long time for processing the same..(can be restart of the target system...)
if you get the error saying predecessor is not in final state...
for this you need to check the parent message in the queue which is causing this. this can be done using messaging system url
http://host:port/MessagingSystem/
go here and check the tab EOIO message ..... and there check the messages which are blocked and check the queue names if need to find the paticular queue..and reprocess if the error occured can be rectified...
HTH
Rajesh

I have a targus 4.0 bluetooth usb adapter and so i can pair my iphone 4s and ipad air wirelessly, it seems to pair ok but when i try to connect i get a error message or not compatible. can some one tell me if it i can use this

i have a targus 4.0 bluetooth usb adapter and so i can pair my iphone 4s and ipad air wirelessly, it seems to pair ok but when i try to connect i get a error message or not compatible. can some one tell me if it i can use this bluetooth with my devices, thanks

sos1der wrote:
pairing the apple equipment is not a big deal just wanted to add songs from itunes wirelessly.
You can only add songs to your iOS device from iTunes via Wi-Fi sync or via your cable, not Bluetooth.
sos1der wrote:
but i tried paring my LG bluetooth so i can listen to music on my computer wirelessly buy it gives me the same error message
That's an entirely different issue, unrelated to your iOS devices.

Getting error in the adapter engine when sending a message

Hi,
I'm always getting this error in the adapter engine: Message processing failed. Cause: com.sap.aii.messaging.util.URI$MalformedURIException: no scheme
The comm channel ends up in error because of messages having the above error.
Could someone please help?
Thanks.
Mike

Mike.
Please check this links.
Check your adapter and restarted.
com.sap.aii.messaging.util.URI$MalformedURIException: invalid port number
Re: Prerequisites to setup configure mail scenario.
error in communication channel
Error :Receiver File Channel not Initialized

Archiving message in Adapter Engine in XI 3.0

Dear all,
Could you please explain the procedure of Archiving Messages in Adapter Engine in XI 3.0.
I have read many blogs regarding deleting messages in Adapter Engine, but nowhere i can see about Archiving.
I have been told that activating and scheduling "Default Version Archive Job" in RWB->Components->Adapter Engine->Background Processing would solve the purpose.
But while activating, i am unale to set rules, as it gives error " Rules are not allowed for jobs with set 'archive edited messages only' flag."
Thanks and regards

Hi,
Please check the [link|http://www.****************/Tutorials/XI/Archiving/Index.htm]
Also check this
http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/402fae48-0601-0010-3088-85c46a236f50?quicklink=index&overridelayout=true
http://wiki.sdn.sap.com/wiki/pages/viewpage.action?pageId=147266890
Regards,
Naveen.

SOAP messages not visible in RWB - Message Monitoring - Adapter Engine

Hi,
following scenario:
ERP is sending IDocs to PI.
Within PI an integration process sends the IDoc data through a SOAP (WS) receiver channel to a system far far away.
In RWB -> Communication Channel Monitoring I can see all delivered messages selecting my SOAP channel.
But:
I can´t see the SOAP messages in RWB -> Message Monitoring -> Messages of Adapter Engine.
In RWB -> Message Monitoring -> Messages of Integration Engine I only see SOAP messages with status "Error".
Successful column is empty.
Do I have to adjust some system / monitoring parameters also seeing SOAP messages in RWB->Message Monitoring?
Thanks in advance,
André

Hi Ravi,
thanks.
But there are thousands of successful messages delivered to the receiver.
These successful messages can only be seen in the Channel Monitoring.
I can´t find these successful messages in Message Monitoring.
Only some with status "Error" are displayed.
Strange...
Cheers,
André

Cannot resend messages in adapter engine

Hi all,
I encountered thousand messages in adapter engine yesterday with error category: XI_J2EE_ADAPTER_ENGINE, error code: JMS_TRANSMISSION_ERROR.
First I checked the affected communication channel, and there was an error in MQ side. Also, our database crashed. But these issues were resolved already. Then I tried to resend the messages, but still it ended up in system error. As I looked in the log,
MP: Exception caught with cause com.sap.aii.af.ra.ms.api.RecoverableException: Connector for ConnectionProfile of channel: JMS_--_Receiveron node: -having object id: - encountered error: MQJMS2007: failed to send message to MQ queue in sending to destination queue:///?targetClient=1, the message message: JMS Message class: jms_text JMSType: null JMSDeliveryMode: 2 JMSExpiration: 0 JMSPriority: 4 JMSMessageID: null JMSTimestamp: 1193614619284 JMSCorrelationID:--
Exception caught by adapter framework: Connector for ConnectionProfile of channel: JMS_----
MP: Exception caught with cause com.sap.aii.af.ra.ms.api.RecoverableException: Pending message discovered: -
.The channel is configured throw an recoverable, temporary error for this warning (default). Decide whether you want to bypass this message. If so, set the Pending Handling channel parameter to 'Bypass' and restart the message afterwards.
Exception caught by adapter framework: Pending message discovered: -
.The channel is configured throw an recoverable, temporary error for this warning (default). Decide whether you want to bypass this message. If so, set the Pending Handling channel parameter to 'Bypass' and restart the message afterwards.
Every time I tried to resend the message, it ended up in error stated above. But there are successful messages today which means that the communication channel is working fine.
How can I resend the messages stucked in the adapter engine? Hope someone can help me.
Thanks a lot in advance.

May be when u tried to send the message some of the message got stuck in AE due to some Error.
As I no the message can stuck in AE when....Target Systems is down, Test data is not valid for receiver..then few of the messages goes in System Error and later message come in waiting/Holding/To be Delieverd state...
Check all the messages that has in System Error status...
Thanks
Farooq.

CPALookupException while sending a Test message to Adapter engine

Hello Experts,
I am getting following exception while sending a test message to Adapter engine through Runtime Workbench.
Error while sending message: com.sap.engine.interfaces.messaging.api.exception.ConfigException: ConfigException in XI protocol handler. Failed to determine a receiver agreement for the given message. Root cause: com.sap.aii.af.service.cpa.impl.exception.CPALookupException: Couldn't retrieve outbound binding for the given P/S/A values: FP=<Configured Party>;TP=;FS=<Configured Communication component>;TS=;AN=<Configured Outbound Interface>;ANS=<Configured Namespace>
This scenario works fine when I submits the message through Integration engine. So ID configuration is perfect. Also cache contents are upto date.
Thanks in advance.
Regards
Rajeev

Error is clearly saying that it is unable to find receiver agreement for that particular interface.
Please check your receiver agreement for the interface.
If your receiver agreement is fine then do CPA cache refresh using following URL:-
http://<host>:<port>/CPACache/refresh?mode=full

PI 7.1 - Message Monitoring - Adapter Engine (Database Overview)

Hi Friends,
In Message Monitoring --> Adapter Engine --> Database (Overview) is not working. It throws the following error message.
no_connection Exception Message: RemoteException in Method: CentralViewManager: getIProfiles( IApplication, boolean ). Communication-related failure. Message: java.rmi.RemoteException: Service call exception; nested exception is: com.sap.engine.services.webservices.jaxrpc.wsdl2java.ClientProtocolException: An error occured while reading data from the destination sap.com/com.sap.aii.af.service.profile.proxy/com.sap.aii.af.service.statistic.proxy.ProfileProcessor/basicPort_Document. The error was: com.sap.security.core.server.destinations.api.DestinationException An error occurred while reading the destination sap.com/com.sap.aii.af.service.profile.proxy/com.sap.aii.af.service.statistic.proxy.ProfileProcessor/basicPort_Document, type WebService. The error was Internal error during the decryption process...
But, Adapter Engine --> Database option is working. What could be the problem ?
Kindly clarify, friends.
Kind regards,
Jegathees P.

Hello friend,
May be it is related with connection problem check with your basis people .
Regards,
Ravi.

Message in adapter engine

Hi all,
We monitor messages in adapter engine through RWB.
Can anyone tell me where these messages are stored?

hi,
it has the misconception that RWB uses the same data base as of sxmb_moni.
but this is not true. actually RWB has a java componenet and IE is a abap componenet.
RWB getting tha data from SXMB_MONI db(abap table) through the jrfc call and storing it into the XI_AF_MSG table. this can be verified because, when u try to fatch payload for the sych message in RWB ,it is showing payload is deleted to save memory . but the same message with the payload can be displayed at SXMB_MONI .but for this u need to set the retention period at sxmb_adm---intigration engine configuration.by default value for this is 0 days.please have a look of below link.
https://www.sdn.sap.com/irj/scn/wiki?path=/display/xi/xi%252btables
the XI_AF_MSG_AUDIT table stored the detail of all the audit log.thats why the no of entrieds in this table is more than XI_AF_MSG table.
now Q is how to access these DB.
these DB can be access through the DB tool say SQLplus.
to get the total no of entries byststus u can use the fllowing query.
select status, count(1) as
current_number from sap[sid]db.xi_af_msg
group by status;
regards,
navneet

How to see old successfully delivered messages in Adapter Engine

We are unable to see the messages that were successfully delivered by Adapter Engine more than a day.Ho do we see old successfully delivered messages by Adapter Engine.We are only able to see the messages that were 1 day old.We are using PI 7.1.
We are able to see the older messages in Integration Engine as per the config in sxmb_adm.
Any Help greatly appreciated.
Thanks,
Aravind

Only message that contain error,holding,not delivered are getting persisted not the sucessfully delivered ones.
Is there any Archiving scheduled for your Adapter Engine?
I want to see the old messages that were delivered sucessfully
In Message Monitoring Itself select Archive (instaed of Database) and make a search.....if archiving is scheduled then you should be able to see the messages by this option.
Regards,
Abhishek.

Error message "the application APPLICATION_NAME can't be opened. -10810"

All of a sudden I started getting the error message "the application APPLICATION_NAME can't be opened. -10810" whenever I attempt to open an application. Sometimes all of the applications will work, but then all of a sudden one or two applications will turn unresponsive and I will get the above message whenever I attempt to open any application. Does anyone know what this error might be, and how I might go about fixing it?

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of this exercise is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login. Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode* and log in to the account with the problem. The instructions provided by Apple are as follows:
Be sure your Mac is shut down.
Press the power button.
Immediately after you hear the startup tone, hold the Shift key. The Shift key should be held as soon as possible after the startup tone, but not before the tone.
Release the Shift key when you see the gray Apple icon and the progress indicator (looks like a spinning gear).
*Note: If FileVault is enabled under OS X 10.7 or later, or if a firmware password is set, you can’t boot in safe mode.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem(s)?
After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

What does this error message mean and how do I solve it? "Sorry, one or more of the following command-line tools was not found: /usr/bin/lsbom, /bin/pax, /bin/mkdir, /bin/chmod, or /usr/bin/update_prebinding."

When I try to open up this program, Pacifist, I receive this error message. Here's a screenshot. http://i.imgur.com/v717w.jpg What does this error message mean and how do I solve it?

It sounds like some of the Unix Executable commands were removed (or the permissions to those were modified) out of the /usr/bin/ folder. You can try opening disk utility and repairing permissions on Macintosh HD or you can reboot your computer and holding down option-r when it comes back up to reinstall Lion again. This will not delete your personal information or applications you have installed but it would be best to back it up to Time Machine before you do. The article on how to do this is here. (http://www.apple.com/macosx/recovery/) I have had to do this before and it works like a charm. It should fix your issue but grab a cup of coffee because its going to take about 35 - 40 minutes depending on how fast your computer is.

Error message in adapter engine, can u solve it

Similar Messages

Maybe you are looking for