EtherChannel between stacked VSS Catalyst 4500X and Stacked 2960X.

I can have only one link in the EhterChannel up but the 2nd one goes in to suspended mode. 
I've tried recreating channel group on different ports but with the same results. Am I doing something wrong or pagp cannot be transmitted over stacks on both ends (I have quite a few EtherChannels but all to single/non-stacked switches)?
2960X stack config
Version: 15.0 (2r)EX
interface TenGigabitEthernet2/0/2
 description HR-Link1
 switchport mode trunk
 switchport nonegotiate
 channel-group 2 mode on
interface TenGigabitEthernet1/0/2
 description HR-Link2
 switchport mode trunk
 switchport nonegotiate
 channel-group 2 mode on
4500X Stack (VSS) config
Version: 03.04.00.SG (fc3)
interface TenGigabitEthernet1/1/12
 description MO-Link1
 switchport mode trunk
 switchport nonegotiate
 shutdown
 channel-group 12 mode on
interface TenGigabitEthernet2/1/12
 description MO-Link2
 switchport mode trunk
 switchport nonegotiate
 shutdown
 channel-group 12 mode on
Thank you,
T

Thanks for reply!
I have tried desirable mode as well but no luck. I can work on this only during the weekend as downtime is not an option.
These two 10G links were just installed last weekend and one patch cable I had to replace due to complete lack of connectivity (small shop so we no fiber testing equipment).
I did not do a lot of troubleshooting last weekend but I will dig in to that this weekend. I was hoping to get some insight from people who work with this on daily basis.
Post from about a year ago got me worried:  https://supportforums.cisco.com/discussion/12072281/4500-x-vss-mec-2960-x-stack
Thanks again.
T

Similar Messages

  • VSS Catalyst 4500X-16 SFP+ / crashing on cat4500e-universalk9.SPA.03.05.03.E.152-1.E3.bin / radius / dot1x

    Hi guys,
    I am not sure if I am hitting IOS bug CSCtx61557
    according to the bug tool this is the info:
    crash after authc result 'success' from 'dot1x' for client (Unknown MAC)
    CSCtx61557
    Description
    Symptoms: The switch crashes after logging "success" from "dot1x" for client
    (Unknown MAC).
    Conditions: The symptom is observed with the following conditions:
    1. A switchport is configured with both of the following:
    authentication event server dead action authorize...
    authentication event server alive action reinitalize
    2. The radius server was down previously, and a port without traffic (for
    example: a hub with no devices attached) was authorized into the inaccessible
    authentication bypass (IAB) VLAN without an associated MAC address.
    3. The radius server becomes available again, and a dot1x client
    attempts to authenticate.
    Workaround: There is no workaround.
    I am running the following IOS on my 4500X-16 SFP+:
    cat4500e-universalk9.SPA.03.05.03.E.152-1.E3.bin
    This is what I configured, and what happened:
    HOSTNAME(config)#aaa group server radius rad_eap
    HOSTNAME(config-sg-radius)# server name ACS1
    HOSTNAME(config-sg-radius)# server name ACS2
    HOSTNAME(config-sg-radius)# server name ACS3
    HOSTNAME(config-sg-radius)#$ication login default group radius local
    HOSTNAME(config)#aaa authentication login CONSOLE local
    HOSTNAME(config)#aaa authentication enable default group radius enable
    HOSTNAME(config)#aaa authentication ppp default local group radius
    HOSTNAME(config)#aaa authentication dot1x default group radius
    HOSTNAME(config)#aaa authorization exec default if-authenticated
    HOSTNAME(config)#aaa authorization network default group radius
    HOSTNAME(config)#aaa accounting update newinfo
    HOSTNAME(config)#aaa accounting dot1x default start-stop group radius
    HOSTNAME(config)#aaa accounting network default start-stop group
    eption to IOS Thread:
    Frame pointer 897BAE38, PC = 1C03EECC
    IOSD-EXT-SIGNAL: Aborted(6), Process = Exec
    -Traceback= 1#49176b00b95a50f3145e3825de17d470  c:1C008000+36ECC c:1C008000+3BE50 c:1C008000+3BF48 :1F679000+201A18C :1F679000+31CEE2C :1F679000+2C22958 :1F679000+2C293E4 :1F679000+1166260 :1F679000+2C3C20C
    Fastpath Thread backtrace:
    -Traceback= 1#49176b00b95a50f3145e3825de17d470  uld:1F224000+2DE8 uld:1F224000+2DE4 iosd_unix:1C3ED000+186A0 pthread:1AA69000+6450
    Auxiliary Thread backtrace:
    -Traceback= 1#49176b00b95a50f3145e3825de17d470  pthread:1AA69000+BB8C pthread:1AA69000+BB6C c:1C008000+F61E4 iosd_unix:1C3ED000+21270 pthread:1AA69000+6450
    Buffered messages: (last 8192 bytes only)
    6 left the port-channel Port radius
    HOSTNAME(config)#aaa accounting system default start-stop group radius
    HOSTNAME(config)#
    HOSTNAME(config)#
    HOSTNAME(config)#no authentication logging verbose
    HOSTNAME(config)#
    HOSTNAME(config)#
    HOSTNAME(config)#login block-for 300 attempts 5 within 60
    -channel1
    *Aug 28 01:08:47.873 UTC: %C4K_IOSINTF-5-LMPHWSESSIONSTATE: Lmp HW session DOWN on slot 11 port 12.
    *Aug 28 01:08:48.056 UTC: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 172.16.5.98 port 514 started - CLI initiated
    *Aug 28 01:08:48.571 UTC: %FASTHELLO-2-FH_DOWN:  Fast-Hello interface Te2/1/12 lost dual-active detection capability
    *Aug 28 01:08:49.099 UTC: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 172.16.250.61 on interface Vlan250
    *Aug 28 01:15:08.753 UTC: %C4K_IOSINTF-5-LMPHWSESSIONSTATE: Lmp HW session UP on slot 11 port 1.
    *Aug 28 01:15:24.759 UTC: %VSLP-5-VSL_UP:  Ready for control traffic
    *Aug 28 01:15:27.760 UTC: %VSLP-5-RRP_ROLE_RESOLVED: Role resolved as ACTIVE  by VSLP
    *Aug 28 01:15:27.760 UTC: %EC-5-BUNDLE: Interface TenGigabitEthernet2/1/1 joined port-channel Port-channel2
    *Aug 28 01:15:28.049 UTC: %C4K_REDUNDANCY-6-DUPLEX_M
    <Thu Aug 28 01:18:32 2014> Message from sysmgr: Reason Code:[2] Reset Reason:Service [iosd] pid:[6813] terminated abnormally [6].
    Details:
    Service: IOSd service
    Description: IOS daemon
    Executable: /tmp/sw/mount/cat4500e-universalk9.SPA.152-1.E.pkg//usr/binos/bin/iosd
    Started at Wed Aug 27 22:27:48 2014 (647795 us)
    Stopped at Thu Aug 28 01:18:32 2014 (115506 us)
    Uptime: 2 hours 50 minutes 44 seconds
    Start type: SRV_OPTION_RESTART_STATELESS (23)
    Death reason: SYSMGR_DEATH_REASON_FAILURE_SIGNAL (2)
    Last heartbeat 0.00 secs ago
    PID: 6813
    Exit code: signal 6 (no core)
    CWD: /var/sysmgr/work
    PID: 6813
    UUID: 512
    FAILURE: syslogd shutdown
    I had a ICMP ping going, and it was not affected, as the Standby VSS chassis kicked in and took over, while the previous active chassis reloaded.
    2nd time it happened:
    Now this time, I had waited until the previous active chassis was back up and running and came back up as Standby hot.
    once again I pasted the same config, and bang, It happened a second time on the second chassis which was acting now as Active supervisor.
    And once again, the ICMP continuous ping was not interrupted, as the other chassis remained up, while the "new" active crashed after configuring the same configs in a slight different order.
    HOSTNAME(config)#radius server ACS2
    HOSTNAME(config-radius-server)#$5.22 auth-port 1812 acct-port 1813
    HOSTNAME(config-radius-server)# timeout 1
    HOSTNAME(config-radius-server)# key 0 XXXX
    HOSTNAME(config-radius-server)#!
    HOSTNAME(config-radius-server)#radius server ACS3
    HOSTNAME(config-radius-server)#$xxxx auth-port 1812 acct-port 1813
    HOSTNAME(config-radius-server)# timeout 1
    HOSTNAME(config-radius-server)# key 0 xxxxxxx
    HOSTNAME(config-radius-server)#
    HOSTNAME(config-radius-server)#aaa group server radius rad_eap
    HOSTNAME(config-sg-radius)# server name XXXX
    HOSTNAME(config-sg-radius)# server name XXXX
    HOSTNAME(config-sg-radius)# server name XXXX
    HOSTNAME(config-sg-radius)#
    HOSTNAME(config-sg-radius)#
    PER-3-S
    Exception to IOS Thread:
    Frame pointer 89455E38, PC = 1CC27ECC
    IOSD-EXT-SIGNAL: Aborted(6), Process = Exec
    -Traceback= 1#e495ba4f9346cc1496eecd01ebf1814a  c:1CBF1000+36ECC c:1CBF1000+3BE50 c:1CBF1000+3BF48 :20276000+201B18C :20276000+31D0DA8 :20276000+2C24800 :20276000+2C2B28C :20276000+11671B0 :20276000+2C3E0B4
    Fastpath Thread backtrace:
    -Traceback= 1#e495ba4f9346cc1496eecd01ebf1814a  iosd_unix:1CFD6000+1C230 iosd_unix:1CFD6000+1C284 iosd_unix:1CFD6000+18854 pthread:1B653000+6450
    Auxiliary Thread backtrace:
    -Traceback= 1#e495ba4f9346cc1496eecd01ebf1814a  pthread:1B653000+BB8C pthread:1B653000+BB6C c:1CBF1000+F61E4 iosd_unix:1CFD6000+21270 pthread:1B653000+6450
    Buffered messages: (last 8192 bytes only)
    INTF-5-TRANSCEIVERINSERTED: Slot=11 Port=3: Transceiver hasW-9(config-sg-radius)#
    HOSTNAME(config-sg-radius)#no authentication logging verbose
    HOSTNAME(config)#
    HOSTNAME(config)#
    HOSTNAME(config)#login block-for 300 attempts 5 within 60
     been inserted
    *Aug 28 01:26:03.864 UTC: %C4K_IOSINTF-5-TRANSCEIVERINSERTED: Slot=11 Port=4: Transceiver has been inserted
    *Aug 28 01:26:03.864 UTC: %C4K_IOSINTF-5-TRANSCEIVERINSERTED: Slot=11 Port=5: Transceiver has been inserted
    *Aug 28 01:26:03.864 UTC: %C4K_IO
    <Thu Aug 28 01:28:10 2014> Message from sysmgr: Reason Code:[2] Reset Reason:Service [iosd] pid:[6770] terminated abnormally [6].
    Details:
    Service: IOSd service
    Description: IOS daemon
    Executable: /tmp/sw/mount/cat4500e-universalk9.SPA.152-1.E3.pkg//usr/binos/bin/iosd
    Started at Thu Aug 28 01:13:52 2014 (60006 us)
    Stopped at Thu Aug 28 01:28:10 2014 (993041 us)
    Uptime: 14 minutes 18 seconds
    Start type: SRV_OPTION_RESTART_STATELESS (23)
    Death reason: SYSMGR_DEATH_REASON_FAILURE_SIGNAL (2)
    Last heartbeat 0.00 secs ago
    PID: 6770
    Exit code: signal 6 (no core)
    CWD: /var/sysmgr/work
    are these the symptoms related to  CSCtx61557 ?
    I have tested this in a test environment, where no ACS was reachable!
    Thanks
    Colin

    Another update,
    It seems not only the 4500X platform is affected, its also 4510R+E's:
    WS-C4510R+E
    WS-X45-SUP8-E
    IOS-XE (cat4500es8-UNIVERSALK9-M), Version 03.03.01.XO
    4510R+E#sh redundancy /| i    | i state
            Current Software state = ACTIVE
           Uptime in current state = 2 hours, 39 minutes
            Current Software state = STANDBY HOT
           Uptime in current state = 6 minutes
    4510R+E(config)#login block-for 300 attempts 3 within 60
    Exception to IOS Thread:
    Frame pointer 8D104E28, PC = C9C0FF4
    IOSD-EXT-SIGNAL: Aborted(6), Process = Exec
    -Traceback= 1#9492282023e5ef761bd83af205155966  c:C98A000+36FF4 c:C98A000+3C2B0 c:C98A000+3C3A8 :10000000+201B994 :10000000+31CA4E4 :10000000+2C1DC54 :10000000+2C246E0 :10000000+116A3F0 :10000000+2C37508
    Fastpath Thread backtrace:
    -Traceback= 1#9492282023e5ef761bd83af205155966  c:C98A000+E29C0 c:C98A000+E29A0 iosd_unix:CD74000+1877C pthread:B3FE000+647C
    Auxiliary Thread backtrace:
    -Traceback= 1#9492282023e5ef761bd83af205155966  pthread:B3FE000+BBB4 pthread:B3FE000+BB94 c:C98A000+FA4E8 iosd_unix:CD74000+21270 pthread:B3FE000+647C
    Buffered messages: (last 8192 bytes only)
    at least one now can directly "redundancy failover" from config mode.....      :)

  • Etherchannel between stack switches[3750] and standalone switch[3560]

    Hi,
    I have 2*3750 switches in stack as core and 1*3560 switch in access layer. I want to enable ether channel between stack switch[3750A & 3750B] and 3560 switches.
    Have connected  2 links from 3560 switch to stack switch, one link to 3750A and other link to 3750B. Will it work in this way as per my requirement? 
    or i should enabled stacking on 3560 switch too and configure cross-stack ether channel between 3750 stack and 3560 stack. i refered few cisco documents, but the cross stack etherchannel configuration example has 3750 at both end stacks.
    Rgds...
    VikramS

    Hi,
     This should work fine as per you set up, the 3750 stack will be acting as one switch, which means that the ether-channel configuration should be straight forward. There is no need to stack the 3560 for this to work, also the 3560 are not stackable.
    Hope this helps.

  • Catalyst 3850 Cross-Stack EtherChannel

    On 3850 configuration guide, I came across PAgP desirable mode is not supported in the switch stack (cross-stack EtherChannel).
    http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3850/software/release/3se/layer2/configuration_guide/b_lay2_3se_3850_cg/b_lay2_3se_3850_cg_chapter_0101.html
    But on Q&A document, it mentioned 3850 supports PAgP.
    Q.    What cross-stack EtherChannel link bundling protocols are supported?
    A.     The Cisco Catalyst 3850 supports Cisco Port Aggregation Protocol (PAgP) and industry-standard IEEE 802.3ad Link Aggregation Control Protocol (LACP). Other 3750 Series Switches support only LACP for cross-stack EtherChannel.
    Seems like both statements are contradicting.
    Can someone shed some light on this?
    Thank you.

    Hi, adimakmur 
    Cisco Catalyst 3850 Cross-Stack EtherChannel can be PAgP+ and can be used for VSS dual active detection.
    In last deployment of 3850 we use Cross-Stack EtherChannel and use it as trusted for VSS dual active detection.
    c6500-V#sh switch virtual dual-active pagp
    PAgP dual-active detection enabled: Yes
    PAgP dual-active version: 1.1
    ----skiped----
    Channel group 106 dual-active detect capability w/nbrs
    Dual-Active trusted group: Yes
              Dual-Active     Partner              Partner   Partner
    Port      Detect Capable  Name                 Port      Version
    Te1/7/7   Yes             c3850-307            Te1/1/3   1.1
    Te2/7/7   Yes             c3850-307            Te2/1/3   1.1
    ---skiped----
    c6500-V#sh etherchannel 106  protocol 
    Protocol:  PAgP
    c3850-307#sh etherchannel port-channel 
                    Channel-group listing: 
    Group: 1 
                    Port-channels in the group: 
    Port-channel: Po1
    Age of the Port-channel   = 235d:20h:50m:10s
    Logical slot/port   = 12/1          Number of ports = 2
    GC                  = 0x00010001      HotStandBy port = null
    Port state          = Port-channel Ag-Inuse 
    Protocol            =   PAgP
    Port security       = Disabled
    Ports in the Port-channel: 
    Index   Load   Port     EC state        No of bits
    ------+------+------+------------------+-----------
      0     00     Te1/1/3  Desirable-Sl       0
      0     00     Te2/1/3  Desirable-Sl       0
    Time since last port bundled:    169d:04h:58m:49s    Te1/1/3
    Time since last port Un-bundled: 169d:05h:00m:47s    Te1/1/3

  • Conecting etherchannel between cisco catalyst 6509 and hp procourve 9308

    Impossible to connet 2 ports 1000base sx agrouped via etherchannel / lacp or pagp between a catalyst 6509 and a hp procourve 9308. Please do you know he best configuration? thanks in advance

    Hola Luis,
    the link would have to be LACP (since PAgP is Cisco proprietary). So, on the Cisco side, the config should look like this:
    interface GigabitEthernet0/1
    switchport trunk encapsulation dot1q
    switchport mode trunk
    channel-group 1 mode on
    interface GigabitEthernet0/2
    switchport trunk encapsulation dot1q
    switchport mode trunk
    channel-group 1 mode on
    interface Port-channel1
    switchport trunk encapsulation dot1q
    switchport mode trunk
    On the HP side, check how the trunk group is configured there. I assume you have used the ´trunk deploy´ command after configuring the HP trunk group ? Also, which spanning-tree mode do you have running on the Cisco and the HP ?
    Saludos,
    GP

  • EtherChannel between 6006 (catos) and Catalyst 2960 HELP

    Hi All,
    I want to create an etherchannel between 6006 (catos) and Catalyst 2960 to have failover and load balace.
    My ports on 6006 (catos) 6/37,6/47 and on 2960 giga 0/1 and giga 0/2.
    I have checked on 6006 it supports channel.
    Please help to configure this.
    Thanks,
    AS

    AS
    Use this doc as a guide and if you have further questions please come back -
    http://www.cisco.com/en/US/tech/tk389/tk213/technologies_configuration_example09186a0080094953.shtml#specialconsid
    Jon

  • What are the differences between Easy VSS and Traditional VSS on Catalyst 4500E with Sup 8E ?

    I would like to know which feature is different between Easy VSS and Traditional VSS.
    I know "Easy VSS is a new way of implementing VSS by using a single command" but I cannot find more information about it.
    Please help.
    Thank you.
    Nash

    Easy VSS is a simplified and automated way of configuring VSS for first time. Once a VSS is configured then it same as traditional VSS in functionality.
    There is no concept of layer 2 or layer 3 VSL link. VSL is the internal portchannel link and you cannot configure as layer 2 or layer 3 portchannel.
    Following is the link of Easy VSS steps.
    http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/XE3-6-0E/15-22E/configuration/guide/xe-360-config/vss.html#60764

  • Fast EtherChannel between Catalyst 3750 and 2821 Router

    Hi Guys
    I'm trying to setup a Fast EtherChannel between a cat3750-smi and a 2821 router that consists of only 2 links.
    I am following instructions per TAC, but I'm getting an error along the way;
    On the cat3750:
    interface port-channel 1
    no switchport
    Command Rejected: Not a convertable port
    Can anyone help???
    Also... do the IP Addresses for the EtherChannel need to be the same for both port-channels? Or do I assign the switch like 192.168.1.1 and the router 192.168.1.2 ?
    Thanks!
    Adam

    Hi Adam,
    The ip address cannot be same but it should belong to same subnet. So one side 192.168.1.1 and other side 192.168.1.2 will work fine.
    Its better to convert your layer 2 port as a layer port fist so what you do the port which you want to be port channel go that that interface and convert with "switchport" command
    once it is a layer 3 port configure with channel group and automatically layer 3 port channel will be created and you can sssign an ip address then.
    Just give a try and update if it works.
    Regards,
    Ankur

  • 10G etherchannel between 4510 and 3850 - NO Link

    I'm pulling my hair out on a simple issue, and I could use some advice.   Thank you, in advance.
    I've got a core 4510 switch with 2 12-port 10GE SFP+ modules and my closet has a stack of 3 3850-48p with 2 4-port C3850-NM-2-10G  modules.
    I'm using 4 SFP-10Gb-SR SFP's to create an ether-channel between these two switches.  
    The fiber between them is OM4 cable, and OM3 patch cables.
    The distance is about 90 Meters.
    I've got po8 created on the 4510 through te1/8 and te2/8.  On the 3850, i've got po8 created on te1/1/4 and te3/1/4.  My problem is that I cannot get a link light at all between these ports.  Absolutely nothing indicating when i hook it up.  I've tested all the patch cables using loop backs and they all respond.  I can even loop back through the complete length of the fiber and i get a link light then also. When i hook them up together, the log on the 4510 starts throwing Rx power low alarms with an Operating value of -29.5 dBm.
    I've had Cisco's support go through and verify my port-channel configuration, and they found it to be correct.  
    I'm starting to wonder if there is larger forces at work here.  Am i bumping into a compatibility issue?
    Any help would be appreciated.

    I've removed the interfaces from the etherchannel and tried cross looping.  On the 4510 I get no indication from the LEDs.  On the 3850 I get immediate indication on the LEDs.
    One might conclude, Cisco support included, that the SFPs on the 4510 side were bad and should be replaced.   I hesitate to conclude this because, while members of the etherchannel, i get link lights when looping immediately.  Its only when setting the 4510 interfaces back to default and outside the etherchannel that i don't get a response.

  • Catalyst 2960 SF Stacking

    Hi
    I am stacking 6 Catalyst 2960 SF Series PoE 48 ports, I am using the Bladestack cable. I plug it in from 1 to 2 on all the switches. If I look at the lights it shows 4 in on group and 2 in another. If I do a show switch detail it shows the following
    Switch/Stack Mac Address : 44ad.d982.a100
                                               H/W   Current
    Switch#  Role   Mac Address     Priority Version  State
    1       Member 5006.0425.7e00     1      1       Ready              
    *2       Master 44ad.d982.a100     1      1       Ready              
    3       Member 5006.0435.bc00     1      1       Waiting            
    4       Member 5006.04d8.7000     1      1       Ready              
             Stack Port Status             Neighbors    
    Switch#  Port 1     Port 2           Port 1   Port 2
      1       Down        Ok              None       2
      2        Ok         Ok                4        1
      4       Down        Ok              None       2

    Hi , i think only four 2960 SF switches can be stacked into a singe logical switch.
    Please refer the link , hope this helps:
    http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps6406/white_paper_c11-578928.html

  • Could connect two Nexus 5648 to a stack of Catalyst 3750?

    Good Morning,
    Can I connect a two Nexus 5600 (switchs distribution) with switch Catalyst 3750 (switch access)?
    I have tried to integrate the Nexus switch in the network as switch distribution, replacing a Catalyst 6500 switch and does not work. Everything is going very slow. Although all the ping function properly.
    Is there any incompatibility connect two nexus 5648 to a stack of Catalyst 3750 by VPC?
    Thank you.
    Greetings.

    Hi,
    There can be many reasons for the switches not joining the stack like SDM template mismatch.
    You may go through the following document:
    http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3750/software/troubleshooting/switch_stacks.html#wp40112
    Thanks
    Ankur
    "Please rate the post if found useful"

  • 6800 Host Ports, Access Clients and Stacking Limitations

    In regards to the 6800 Instant Access Solution, it's my understanding that the current OS (Release 15.1(2)SY) will support 1008 host ports across 21 Instant Access clients and that the Instant Access clients will support stacking up to three clients.
    http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-6800ia-switch/white_paper_c11-728265.html
    Is there a forecast as to when the client stack size will be increased?

    Vzambo,
    If you have c6880 or sup 2T you can run newer version 15.2(1)SY. This suuport up to 2000 ports, fabric link 42 and stacking up to 5.
    Tony

  • Etherchannel between 2900 and 7200

    Hello,
    We have Etherchannel trunk set up between Catalyst 2924 switch and 7200 router. The trunk consists of 2 links with source-based forwarding, STP disabled on switch and on the router. For some reason, we can't achieve load-balancing on the trunk, that is, one link is currently used at 100%, another at 20%. We would like to achieve 50/50 utilization. Is it possible to do?
    Thanks !
    Konstantine

    The Etherchannel trunk consists of 0/11 and 0/12 interfaces.Here's the output from "Show interface" command on a switch:
    FastEthernet0/11 is up, line protocol is up
    Hardware is Fast Ethernet, address is 0001.96bb.51cb (bia 0001.96bb.51cb)
    MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
    reliability 255/255, txload 219/255, rxload 49/255
    Encapsulation ARPA, loopback not set
    Keepalive not set
    Full-duplex, 100Mb/s, 100BaseTX/FX
    ARP type: ARPA, ARP Timeout 04:00:00
    Last input 2w6d, output 00:00:40, output hang never
    Last clearing of "show interface" counters 5w0d
    Queueing strategy: fifo
    Output queue 0/40, 0 drops; input queue 0/75, 0 drops
    5 minute input rate 19376000 bits/sec, 7347 packets/sec
    5 minute output rate 86004000 bits/sec, 8 packets/sec
    FastEthernet0/12 is up, line protocol is up
    Hardware is Fast Ethernet, address is 0001.96bb.51cc (bia 0001.96bb.51cc)
    MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
    reliability 255/255, txload 22/255, rxload 58/255
    Encapsulation ARPA, loopback not set
    Keepalive not set
    Full-duplex, 100Mb/s, 100BaseTX/FX
    ARP type: ARPA, ARP Timeout 04:00:00
    Last input 00:00:08, output 00:00:01, output hang never
    Last clearing of "show interface" counters 5w0d
    Queueing strategy: fifo
    Output queue 0/40, 0 drops; input queue 0/75, 0 drops
    5 minute input rate 22747000 bits/sec, 7947 packets/sec
    5 minute output rate 8678000 bits/sec, 2548 packets/sec
    As you can see, the output rate on interface 0/11 is 300 times lower than on 0/12 and that is our main problem. We have a web farm here (around 100 servers), which is connected via Layer 4 switch to 2924 and then, via Etherchannel trunk, to 7200 router which is default gateway. We tried to use destination-based forwarding (on a switch), but that didn't change anything. The router AFAIK doesn't have any settings to change the forwarding.

  • Why can't we have folders AND stacks in the dock?

    If I drag a single item into the dock, I want it to remain a single item.
    If I drag multiple items into the dock, I want them to become a stack.
    If I drag one folder filled with multiple items, it should only turn into a stack on my say-so, like if I Option-Drag it onto the dock or something. Stacks shouldn't be forced onto the user.
    Please make Stacks an ADDED FEATURE and not an ABSOLUTE CHANGE in everyone's daily workflow.

    I might actually buy a windows laptop.  So sad.
    No need, as long as Apple continues to offer a notebook line-up that includes built-in optical drives, to buy a Windows machine... yet.
    As I said, the only thing that I use my SuperDrive for now is backups of all those digital software deliveries, documents, etc. If I finally break down and buy an external Blu-ray drive, I won't use the SuperDrive at all. But right now I have almost 12 years of back-ups on DVD, both single and dual layer - so, for now, I need my optical drive.
    I'm hoping that - one day - Apple will sell MacBook Pros with Blu-ray drives. Hey, I can wish, right?
    Clinton

  • Image size and stacking problem with FF12 even in safe mode. Images are 5x the right size and overlayed on top of other pictures or text. how to fix?

    OK this problems limited to Facebook only. When logged in FF12 the entire page is scrambled. The pictures are stacked over each other and are 5 to 6 times the size their supposed to be. I have tried everything I could think of to fix this it even runs like this when in safe mode. I have uninstalled all plugins and all extensions I have uninstalled and even tried back dating FF. it's still so massively out of proportion that you can't do anything. .even when zoomed out 3x it's so large the pictures are larger than my screen. They are still overlapped so bad you can't do a thing with it. Even worse I uninstalled and installed pale moon and the effects migrated to that browser as well. Only browser I found unaffected by this is IE. Lord knows I don't wanna ever have to go that rout so I'm asking for help. I have a whole list of parsing errors and decoration drops, to many to post. any help would be much appreciated until it's fixed I'm stuck with IE. Chrome wont work with the software I run only IE or FF will.

    -> press '''CTRL''' + '''0''' (zero) to '''Reset''' Zoom
    * For details, see this article -> [[How do I use Zoom?]]
    Check and tell if its working.

Maybe you are looking for