Ethernet problem (Intel 82579V)

Hello,
got a laptop which doesn't recognize the ethernet driver properly (yellow exclamation mark). It's disconnected, ethernet cannot be used. Driver is showing a code 10 error ('this device cannot start').
The eventlog id: 24
source: e1cexpress
Uninstalled the driver and tryed the hp listet network driver (v12.2.45.5033) as well as the latest original driver from Intels website (v19.5.303.0). Also unpacked the Intel-exe and installed it manually via hardware manager.
Hardware-IDs:
PCI\VEN_8086&DEV_1503&SUBSYS_17AB103C&REV_04
PCI\VEN_8086&DEV_1503&SUBSYS_17AB103
PCI\VEN_8086&DEV_1503&CC_020000
PCI\VEN_8086&DEV_1503&CC_0200
Any suggestions?
BR
Michael

Hi,
Please download the right version (32bit or 64bit) and install on your computer:
https://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=18713&lang=eng&OSVersion=Windows%207...
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Similar Messages

Z77A-GD65 Problems with Ethernet (Intel 82579V) Code 10 and 55 error

it is just a day with disaster. I bought Z77A-GD65 yesterday, and now it almost driver me crazy , i have two most famous problem of the board ,the CODE10 and ERROR 55!!!
after i bought this board to home ,i spend few hour to figure out the reason why the system can not be booted.
the DIMM SLOT 3&4 of my board is malfunction,no matter what combination i use (1&3,2&3, 3&4...etc),but it works for 1 and 2(i have 4 ram sticks,all of them is fine)
i do upgrade to BIOS 10.5(thx god ,i have two computer ,otherwise i cant even do it because of following issue)
after i solve the problem by only plug in 2 ram (DIMM1&2), succeed to boot up, a new problem occurred to me ,the CODE10!
latest driver , clean system install ,cmos cleaned, does not help.
i have read this thread for code10
https://forum-en.msi.com/index.php?topic=158591.msg1167303#msg1167303
and for error55
https://forum-en.msi.com/index.php?topic=158224.0
it seems the best way to solve it is RMA.
I notice that there is an Authorized Motherboard Repair Center (East Coast):
361 Alden Road
Markham, Ontario, L3R 3L
i live in Toronto, can i just go there and give the board to them to fix it or i can only mail it?
If i need to mail it ,what should i do?

Code 10 means the device cannot start. You have the right driver for the Intel 82579V is shorted by either a motherboard screw or a raiser under it. The ethernet adapter has lights which light up id driver is installed (even though code 10 is in effect).
Solution: Remove 1 or 2 motherboard screws and turn the pc on. Repeat until you find out which screw caused the issue. For me it was the screw closest to the ethernet controller.
The wa i fixed it was I was used a plastic washer and I was still able to have the motherboard screw in and at the same time not get code 10 anymore and my Intel 82579V worked fine since.

Window 10 build 10041 does not work with Intel 82579V Gigabit Ethernet on ASUS motherboard

I originally posted this question here:
answers.microsoft.com/en-us/insider/forum/insider_wintp-insider_update/window-10-build-10041-does-not-work-with-intel/6729892f-83aa-4822-b20a-ea84f4fd06c7
and was asked to post it on this forum...
I updated a computer I have which is a quad core i7 that I built and includes an ASUS motherboard with Intel 82579V Gigabit Ethernet built in. Windows 10 preview 9926 worked fine with this network adapter. Window 10 build 10041 does not, and I have tried
it twice so far. I even went as far as buying a Thunderbolt-Gigabit Ethernet Adapter (Broadcom, sold by Apple)... and while it installed the driver automatically, it did not work either. Each time you try to view the properties of either of them, it locks
up or give an error. In fact, doing much of anything with the Intel adapter icon assures you of not being able to do a clean reboot... have to kill power. I have finally gone back the previous version 9926, which has its issues but no where near as bad
as not having any network connectivity! Does anyone have this issue and a workaround?
Note, there are two images on the windows 10 preview forum that I posted this question on. I could not post the full link as I was getting a message here that links and graphics are not allowed.

Thanks Roger, I posted the following yesterday in the other thread (thinking it was this thread - confusing after they moved it here)... It may be that the new driver fixes the issue that 10041 has with it, but I have not tried that yet. If I do I will update
this... Thanks!
I have more information about this, which basically exonerates any issue with the Intel 82579V Gigabit Ethernet hardware or software. I have 3 computers with Windows 10 preview so I have multiple angles to see issues from. With this I have found a culprit
(but I suspect not just the only culprit) in this above mentioned problem...
10041 build combined with installing (or attempting to install) CISCO VPN Windows 7 64bit 5.0.07.0440-k9 client causes the issue mentioned above. I confirmed this on a completely different machine with a totally different Ethernet adapter. First machine
is an ASUS motherboard in a tower system I built, with the Intel 82579V Gigabit Ethernet hardware built in. Second machine is a Gateway Laptop from 2008 which has a Marvell Yukon 88E8057 PCI-E Gigabit adapter built in. Build 10041 will work fine with my 2008
laptop, including the MS VPN client (which I have tested). However, if you attempt to install or even uninstall the Cisco client you will have to do a recovery to a restore point (as I have done twice) in order to get your network working again. Installing
or attempting to install (because it never even does install properly and times out), CISCO VPN client will render your entire network unusable. Going back to a restore point saved me and I am still running 10041 but I can't use CISCO VPN client any longer.
I could with build 9926, including on all 3 machines. I now have 9926 on two machines and 10041 on only the 2008 laptop.
Hopefully this above information helps someone resolve the issue. I will also mention, even though my network is working on the 2008 laptop, I still can't go into the Control Panel\Network and Internet\Network Connections and right mouse click on the Marvell
Yukon 88E8057 PCI-E Gigabit adapter icon. I get an error when clicking on Properties menu popup : "An unexpected error has occurred". So something is still up with my network adapter driver or windows software, but it could be a side effect of all
that has happened with the Cisco software install attempts under 10041.
Another note: CISCO Anyconnect also has the issue.

Intel 82579V NIC problem - kernel regression?

Hi all,
I recently upgraded my desktop motherboard to an Asus Maximus GENE-IV, which has the Intel 82579V Gigabit NIC. I installed arch the usual way, dd-ing the latest install image onto a USB stick, and what have you. Trouble is, as soon as I upgrade the kernel and reboot, my NIC stops working in a peculiar manner. It will come up after I do 'sudo ip link set eth0 up', and acquire a carrier. Then, after about ten seconds, the carrier drops. Then it'll come back up again... and drop again. Over, and over, and over. This does not happen with kernel 3.0.3, which is the kernel installed by the latest install image, but it happens with every kernel from 3.0.7 onward (3.0.7 is the oldest kernel I have available to test with, from /var/cache/pacman/pkg on another machine). The most frustrating thing is that I've been googling the problem for two days now, and I can't find anyone who has quite the same issue
The driver is e1000e, and it's autoloaded. My system is an x86_64 one. Has anyone experienced this themselves or heard of it anywhere else? I'd like to avoid manually building the intel driver sources if it's at all possible, because it works fine with an old kernel. /frustration
Edit: dmesg is flooded with "e1000e: eth0 NIC Link is Up" messages.
Edit: further weirdness: when I set a static IP on boot from rc.conf, the interface stays up, but I can only see machines on my local network - DNS does not work, even after putting a nameserver entry into resolv.conf and rebooting.
Edit: I did a clean install, marked the linux kernel as a package not to be upgraded, and did a pacman -Syu. Even with the old 3.0.3 kernel, after the update, my NIC is broken in exactly the same way. I'm really stumped on this!
Last edited by andrew-wja (2012-01-10 21:21:29)

Works fine here, same driver, static IP though.
$ uname -a
Linux amalthea 3.1.8-1-ARCH #1 SMP PREEMPT Sat Jan 7 08:03:08 UTC 2012 i686 Intel(R) Celeron(R) CPU G530 @ 2.40GHz GenuineIntel GNU/Linux
$ lspci|grep Ethernet
00:19.0 Ethernet controller: Intel Corporation 82579V Gigabit Network Connection (rev 05)
$ lspci -nn|grep 00:19.0
00:19.0 Ethernet controller [0200]: Intel Corporation 82579V Gigabit Network Connection [8086:1503] (rev 05)
$ dmesg|grep e1000e
[ 3.965629] e1000e: Intel(R) PRO/1000 Network Driver - 1.4.4-k
[ 3.965632] e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
[ 3.965664] e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 3.965673] e1000e 0000:00:19.0: setting latency timer to 64
[ 3.965772] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[ 4.271943] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) xx:xx:xx:xx:xx:xx
[ 4.271946] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[ 4.271980] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: FFFFFF-0FF
[ 7.196733] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[ 7.248933] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[ 10.186878] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
Last edited by .:B:. (2012-01-09 21:24:59)

Intel 82579V network controller "This device cannot start" (code 10) error"

I've just finished installing a Z77A-GD55 motherboard and had a problem where the Intel 82579V network controller wouldn't start after a cold boot. Device manager would show “This device cannot start" (code 10) error”.
After a reboot it would work every time. During the time it didn't work the adapter was incorrectly shown in device manager as 82579LM. There's an older thread about this issue but the fix described there were of no help with my problem.
After a lot of searching I found Intel has provided a fix for people having this issue after sleep mode so I gave it a try and it seems to work for my issue too, so far anyway.
So if anyone else is having this problem with the same Intel network controller I suggest giving this try.
Go to the Intel Download Center and search for 82579V. Select the first result entitled "NVM Update Utility for Intel® 82579V Gigabit Ethernet PHY Network Connection" and follow the instructions. Good Luck!

Thanks for the information.

Macbook Pro ethernet problems

Hi All:
First post here. I have a 15" first generation MBP, and I'm having some ethernet problems. When my ethernet works, it works fine. However, if i were to shut down the machine and disconnect the ethernet cable, I cannot reconnect to the ethernet. In Network Preferences, Ethernet is not available in the pulldown and it appears gray-ed out in the Network Port Configurations. Restarting the computer, unplugging or resetting the modem doesn't help. Also, the PC link light on the modem will not be lit (but is lit when working).
The computer will not connect to any ethernet network, no matter where I am.
I've noticed if I keep resetting both comuter an modem a couple dozen times over a few hours, the PC link button will light, and upon next startup the ethernet connection will be restored. What do you guys think the problem is? It seems abnormal to me.

Had a similar situation with mine back in January, 2.16 Intel.
After spending 3 nights with my Cable ISP as the connection would drop-off, ethernet light flicker green,amber etc.
Took it back to Apple dealer, connected to Dealers network same problem. Cause:::: Motherboard had to be replaced, possible soder loose on the MO. Got it back in 10 days, haven't had a problem ever since.
Suggest you take back yours to have Apple dealer try this out.
zimer

HELP!!! Mac G4 450mhz dual ethernet PROBLEMS!

Hello, my mac is having a serious problem with the internet. It won't connect, and even though i have a ethernet cable plugged in, it says i don't. Everything was working fine until i left for 2 days and and plugged it for that time. I need the internet in that mac as soon as possible.
PLEASE HELP ME!

I too, am having the same problem... but mine isn't because of the possible software update, it just flat out doesn't work!
I too, have tried asking for help with the possibility of (hopefully) restoring the driver/extension... but after reformating the drive and reinstalling the software from 10.2, to 10.2.8 and it still failed to work, I ended up buying a Belkin Gigabit Ethernet PCI Card that has FAILED in every way!!!
The Belkin card will work as a one-time thing, and after restarting or disconnecting the Ethernet cable, it fails to function and fails to be "selectable" within the Ethernet configuration "Show:" options.
...so don't buy the Belkin...
I have yet to resolve my dead Ethernet problem, and it is... a problem!
I know this isn't contributing much of anything, but don't waist your time with the Belkin. I bought one, it acted in the way described above, and the Belkin Tech Support suggested I exchange it with another one, and so I did... and it too... is acting in the manner described above.
No resolve... no Ethernet... no on-line schtuff. not on that G4!!!
Jon

Z77A-GD65 intel 82579v code 10..

Hello..
Korea because I'm not good at English.
To Z77A-GD65. Something else rather than intel 82579v due to an error code 10 is crazy right before ..
Left did not have to install the new driver, the only way to change the BIOS, seriously, do I know you yihyeonsang resolve BIOS version?

Please read this thread
https://forum-en.msi.com/index.php?topic=158591.0

Z77A-GD65 Problems with Ethernet (Intel 82579V) Code 10

Hi,
on a fresh install of Windows 7 64bit i cannot make the Ethernet port on the motherboard work. It installs fine, but when i check device manager i see this message:
This device cannot start. (Code 10)
I downloaded the latest driver, but still no change.
Looking in device manager, i noticed that the driver Windows had selected was Intel 82579LM, so i reinstalled the driver, and forced 82579V driver, but still no change. I assumed this must be a defect motherboard, so i rma'd it, and got a new one....with the same problem!!!
So any ideas with to do ?

Quote from: Warner on 11-May-12, 04:10:22
Hello kaizerman,
Are you in the US?
Can you send the motherboard to me directly for analysis?
If needed, I will replace the board for you through RMA service.
Please email me at [email protected] but be sure to put my name in the subject field and your board model so it will come to me correctly.
Sincerely,
Warner
Hi Warner
Thanks for the reply. Unfortunately i'm not not in the US, i'm in In South Africa. Ive tried pro17 with no success... currently its showing the 82579V driver. but no still has the cannot start error code 10. I cant understand why it was working for a few days. then suddenly stopped. i made no hardware or software changes.
regards
Utterly perturbed

IMac DualCore with Ethernet problem

Hi,
today I received my new iMac Dualcore 17". But after installing I suddenly realized that the ethernet port is not working. I plugged in my DSL-cable and nothing happend. The modem is working fine with my older Mac. Apple Support Chat advised me to reset both the PRAM and SUM, but unfortunately with no success.
Does anyone of you have a clue what to do? I'm not very keen on sending my new iMac back to Apple and waiting another couple of weeks before they get it fixed.
Thanks in advance to any reply!
Cheers,
Mathias
(Munich - Home of the Oktoberfest)
iMac G4/iBook G3/iMac Intel Mac OS X (10.4.4)

Do you have any details s to the problems you
experienced with the Cisco Switches? I also have a
Cisco VoIP system in place and I keep getting kicked
off the network when connected through the phones.
Did you just plug the computer into the wall and
disable all the 802.11q trunking on that port? If
so I think I may have another jack close by that can
be set up for this specific computer.
Correct. 802.1Q trunking is specifically what the Ethernet interfaces on apparently all Intel-based Macs to date are having troubles with. In other words, disable the aux VLAN on a switch port, and the Intel-based Mac's Ethernet will work on that port. (Obviously this suggestion assumes you have netadmin privileges over your switch!)
It concerns me that no software update has yet been released for this problem. One would think if it were simply a driver issue, an updated driver would have already been released. Thus, one might be lead to believe that the problem goes deeper than software.
PowerBook G4 17" 1.33 GHz 2GB/80GB Mac OS X (10.4.5)

Mac Mini Vs. Fritz Box 7390, ethernet problem (LAN)

Hey wellwishers,
A few days ago my internet provider came in and installed the fibre optics internet. They came with a new modem as well, the Fritz!Box 7390. While connecting all my devices, everything seemed to work just fine, until I lined up my Mac mini. For some reason only the wireless internet seems to work. The wired connection also seems to be recognized just fine (IP configurated, green icon in front, etc.) but it doesn't seem to work at all. The browsers and programs just show there is no internet connection.
I've called the internet provider, and after several attempts of fixing it (by changing IP's and whatever) they redirected me to Apple, saying the Mac mini's with the "Farallon Network Cards" tend to show problems with this modem. There was a way of fixing it but I had to update the driver. (Mac mini is up to date)
So I had google do the dirty work for me, and I found some things to do such as removing/renaming the network preferences file, resetting the router, trying diffirent cables and check on another network to determain if it actually was the modem or the Mac mini. Been there, done that, yet I still didn't get it to work properly on the Fritz!Box only.
I've been told that I should find an update for my network card, but I haven't found a way on how to do that yet.
Where can I find devices updates like that? Anyone here seen a problem like this before with the Fritz!Box 7390? This is 2/3, hoping to find a solution here. Else I have to knock on the door of the Fritz!Box company themselves..
Thanks!
edit: Its a Mac mini. (Mid 2011)
Had OS X Snow Leopard. Re-installed the files hoping that would work, but it didn't. Decided to just update to OS X Mountain Lion v10.8.1, hoping that would work..

No driver required.
Does that cable work OK on another computer?
Does Network Properties show cable unplugged?
On the the other end of the cable is the light lit by the connected port?
Try resetting the SMC and PRAM
Intel-based Macs: Resetting the System Management Controller (SMC)
About NVRAM and PRAM
System report under Hardware>Ethernet Cards is the ethernet hardware listed?

Acer 1810tz video output problems intel 4500mhd

I cannot get video output on my acer 1810tz via both hdmi and vga - no signal as far as I can tell. According to this ubuntu wiki article there are no known problem with video out:
https://help.ubuntu.com/community/Aspir … with%20VGA
and I have installed the display package as suggested by this wiki article:
http://wiki.archlinux.org/index.php/Ace … ine_1810tz
I don't have an xorg.conf as the auto-detect seems to work for me (other than this).
lspci:
lspci
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03)
00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03)
00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03)
00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03)
00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93)
00:1f.0 ISA bridge: Intel Corporation ICH9M-E LPC Interface Controller (rev 03)
00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03)
01:00.0 Ethernet controller: Atheros Communications Device 1063 (rev c0)
02:00.0 Network controller: Intel Corporation WiFi Link 1000 Series

I have only used the normal display and hdmi until now, worked without a problem. Xorg with no config.
$ xrandr --output HDMI1 --auto
xrandr output with no device connected.
$ xrandr
Screen 0: minimum 320 x 200, current 1366 x 768, maximum 8192 x 8192
VGA1 disconnected (normal left inverted right x axis y axis)
LVDS1 connected 1366x768+0+0 (normal left inverted right x axis y axis) 256mm x 144mm
1366x768 60.0*+
800x600 60.3
640x480 59.9
HDMI1 disconnected (normal left inverted right x axis y axis)
DP1 disconnected (normal left inverted right x axis y axis)
HDMI2 disconnected (normal left inverted right x axis y axis)
DP2 disconnected (normal left inverted right x axis y axis)
DP3 disconnected (normal left inverted right x axis y axis)

Z77A-GD65 occasional ethernet problem (code 10)

Hey folks,
got a strange problem here. My ethernet sometimes refuses to work. Usualy after the PC has been turned of for a few minutes.
It acts like this.
Problem:
1. Turn PC on after a minute or so of not beeing powered
2.a. In Windows, no ethernet (code 10, cant start device)
2.b. If I skip Windows and go directly to the Bios, the NIC interface says its "disconnected"
3. soft reboot, reset or even powering it down and start aggain fixes the problem.
Conclusions / Checks done so far:
* checked for extra raisers severeal times now, got none and the behaviour doesnt seem to be a shortage in any way either.
* its not a windows problem either because the bios itself allready says the NIC is "disconnected" which it isnt.
* doesnt make a difference if OCed (using OC Genie) or not.
* RMAed my first board and got a new one, same problem.
* BIOS: activated WakeOnLAN to force NIC staying active, didnt help
* BIOS: disabed auto negotiation and set fixed etehrnet speed value, didnt help
* BIOS: reflashed BIOS 10.7 (7751vA7.zip, release 2012-10-25), didnt help
I read here somewhere that some people had troubles with Nvidia cards leading to the same behaviour which migth be the same case for me.
yet i havent found a fix for this problem yet.
Current Hardware:
- Intel Core i5-3570K
- MSI Z77A-GD65 (S/N: 601-7751-020B1209048802)
- G.Skill DIMM 16 GB DDR3-2133 Quad-Kit
- Asus ENGTX560 Ti DCII TOP/2DI/1GD5
- XFX 650W XXX Edition ATX (powersupply)
help me please, this is awefully annoying especialy for such an expensive board.

I had some werid issues like this intermittantly with a specific nic driver.
Try this for win7: http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=18713&lang=eng&OSVersion=Windows%207%20%20*&DownloadType=Drivers
Win8: http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=21642&lang=eng&OSVersion=Windows%208%2C%2064-bit*&DownloadType=Drivers
Also, have you re-installed the ME drivers:
http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=22092&keyword=management+engine&lang=eng

Z77A-GD65 Ethernet Problems "Network Cable Disconnected"

I've been running a Z77A-GD65 and have been having network problems with the onboard ethernet. Every time I go to play a game online I'll play for about 10-15 minutes and I'll be disconnected. When I'm back on the desktop, my ethernet icon on the taskbar will show "network cable disconnected" even though everything is plugged in fine. Fiddling with the cable or changing the cable does nothing. Reboot the machine and it's working fine until again I play a game for 10 or 15 minutes and the same thing happens.
First, the card was showing the wrong MAC address as specified in the MSI FAQ for this mobo. Performed the fix but the problem is persisting. Tried the MSI driver and the newer Intel one. One time I got a "Code 10" error as posted in another thread and again, wouldn't correct itself until I rebooted.
This only happens when I'm playing games. Web surfing or downloads work fine and my connection won't be disconnected until about 10-15 minutes into playing an online game.
I put in another discrete Intel network card and that worked fine. No problems. Same with plugging in a USB wifi adapter (my current temporary solution). Therefore, I'm thinking it's an issue with the onboard ethernet or driver. Anyone else with this problem or how to resolve it? Using the latest v10.5 MSI BIOS.

Removing the Asus Xonar did not help.
Re-flashed the BIOS as well using a DOS boot USB key instead of M-Flash. Readjusted all setting to default. Enabled/disabled "Network Stack" in the BIOS (what is this supposed to do anyhow? It's undocumented).
Wiped all drivers for this network adapter and re-installed the current ones from MSI's website. No change.
Noticed that the adapter would correctly run at gigabit full-duplex when set to auto-negitiate. However, it would drop down to 10mbps before it finally showed "cable disconnected". Plugging and unplugging the cable did nothing until I reboot, then it would work again... until I ran a game online and it would disconnect after 10-15 minutes of play. Ran the Intel cable test and it was fine (and the cable and internet has been fine when used in conjunction with another discrete PCI-e Intel card).
Re-crimped the ends to be sure. Tested again and the cable connection is good. Yes I know how to crimp ethernet so please don't suggest anything being wrong with the cable.
I've pretty well nailed down that it is an issue with the onboard ethernet. I've read on Intel forums about problems with this chip on Asus boards. Hopefully an MSI employee can point me in a direction that could help, or at least have the problem resolved in a future BIOS update.

Msi kt3 ultra aru ... Cnet pro200 Ethernet problem..

Hi guys
i have this wierd problem i cant figuer out
i just bought a new mobo an msi kt3 ultra aru and amd palamino xp 1800 512 mb kingston pc2700 ram
asus geforce (2) v7100 pro mx-400
the ohter stuff i have is imb deskstar 40gb maxtor diamond 7gb asus dvd and plextor 12/10/32 cd writer
the only pci card i have installed is Cnet pro 200 100/10Mbps Ethernet adapter..
i made a clean install whit winxp pro and i have installed the 5.40 bios and the new 4 in 1 from via and newest nvidia graphics driver
and im on broadband using a cable modem (dialup)
the problem is when i start the computer and windows is loadet i takes up to 30 - 45 sec before i can connect to the internet and proggys like virus protectors and firewalls also after 30 - 45 sec
but if i take the r45 cable out of the modem and start the computer it loads everything in a sec
then i plug the cable in a agin and i have acces to the internet
i have followed mr stevo and racerx27 bios settings
is there any one out there
who have a solution to my problem?
if so then i can be reached at [email protected]

Think your network (TCP/IP) settings are wrong in some way..

Ethernet problem (Intel 82579V)

Similar Messages

Maybe you are looking for