Failure/Er​ror Informatio​n in Postbatch
I have a custom DLL that prints a string I feed it to an attached Epson Receipt Printer. The intention is that if a TestStand socket has a Failure, Error, or Termination I will print a receipt for that socket which shows what step failed or had an error and if it was a measurement what the measurement was.
I am trying to figure out what variable in the Batch model PostBatch sequence stores information about what test step failed or had an error and also where I can get measurement details for that particular step. The intent is to construct a string based on this information and feed it to the Receipt Printer DLL. I wish to only grab the first failure/error encountered in the chain if there are multiple steps failing.
Can someone point me to the variables I need under the Batch model to gather these details? Also, if it is a variable, inside an array, under a cluster etc. what is the structure to the path of the variables I need to be concerned with?
OK I did some more digging and here is what I found under PostBatch. Below is data from variables I pulled after a manual search when I ran my test. The ResultList[18] represents the first subsequence that had status=failed and the ResultList[6] was the first step within that subsequence that failed. This is going to be pretty difficult and involved to parse out because how deep the levels go with SubSequences. Also, different step types will require me to pull in different fields (ie NumericLimitTest vs. Pass/Fail steps. Any suggestions on how to make a simplified expression for this?
Parameters.ModelData.TestSockets[3].MainSequenceResults->Status = Failed (string)
Parameters.ModelData.TestSockets[3].MainSequenceResults->TS.SequenceCall.ResultList[18].Status = Failed (string)
Parameters.ModelData.TestSockets[3].MainSequenceResults->TS.SequenceCall.ResultList[18].TS.StepName = Test Audio Loopback (string)
Parameters.ModelData.TestSockets[3].MainSequenceResults->TS.SequenceCall.ResultList[18].TS.SequenceCall.ResultList[6].Status = Failed (string)
Parameters.ModelData.TestSockets[3].MainSequenceResults->TS.SequenceCall.ResultList[18].TS.SequenceCall.ResultList[6].TS.StepName = Primary_Mic_Test Frequency 200Hz (string)
Parameters.ModelData.TestSockets[3].MainSequenceResults->TS.SequenceCall.ResultList[18].TS.SequenceCall.ResultList[6].Numeric = 1715.853958 (number)
Parameters.ModelData.TestSockets[3].MainSequenceResults->TS.SequenceCall.ResultList[18].TS.SequenceCall.ResultList[6].Units = Hz (string)
Parameters.ModelData.TestSockets[3].MainSequenceResults->TS.SequenceCall.ResultList[18].TS.SequenceCall.ResultList[6].Limits.Low = 199.000000 (number)
Parameters.ModelData.TestSockets[3].MainSequenceResults->TS.SequenceCall.ResultList[18].TS.SequenceCall.ResultList[6].Limits.High = 201.000000 (number)
Parameters.ModelData.TestSockets[3].MainSequenceResults->TS.SequenceCall.ResultList[18].TS.SequenceCall.ResultList[6].Comp = GELE (string)
Parameters.ModelData.TestSockets[3].MainSequenceResults->TS.SequenceCall.ResultList[18].TS.SequenceCall.ResultList[6].TS.StepType = "NumericLimitTest" (string)
Similar Messages
-
I got this error while trying to run a file archiving job on a large number of files. I noticed the memory usage was rising steadily until it finally stopped and then generated this error. Any ideas what could be causing this?
Hello,
That looks like a very old indication of an internal LabVIEW error. The conditions you describe indicate it could be a memory leak - perhaps you are opening many references and not closing them somewhere in your code? Unfortunately, if the problem is in LabVIEW, and not the programming behind your application, I don't think R&D is going to be willing to consider fixing problems found in LabVIEW 5.1 - the product is now in version 8.0.
I hope it turns out to be in your code, and that you're able to fix it by removing a memory leak somewhere!
Best Regards,
JLS
Best,
JLS
Sixclear -
I posted a thread a while back when I was getting sporadic failures. At that time, the general consensus was that 10.5.3 introduced some errors in TM. I'm at 10.5.6 now and have been since the update. But over the past week, I've been getting more frequent TM failures. They seem to be pretty consistent. Below is the info from the log file. The strange thing to me is the reference to "500 Gigger" b/c that is my Super Duper backup and has nothing to do with my TM backup. My TM backup drive is labeled "1TBTM". Any suggestions?
3/21/09 5:51:09 PM mds[21] (/Volumes/500 Gigger/.Spotlight-V100/Store-V1/Stores/C3E5E22C-5296-4418-B36C-F364D997C440)(Er ror) IndexCI in ContentIndexOpenBulk:Could not open /Volumes/500 Gigger/.Spotlight-V100/Store-V1/Stores/C3E5E22C-5296-4418-B36C-F364D997C440/liv e.0.; needs recovery
3/21/09 5:51:10 PM /System/Library/CoreServices/backupd[165] Backing up to: /Volumes/1TBTM/Backups.backupdb
3/21/09 5:51:10 PM /System/Library/CoreServices/backupd[165] Error (-35): Getting volume path
3/21/09 5:51:10 PM /System/Library/CoreServices/backupd[165] Couldn't initialize backup volume from path: /Volumes/1TBTM
3/21/09 5:51:10 PM /System/Library/CoreServices/backupd[165] Error (-35): Couldn't get library parent ref /Volumes/1TBTM/Backups.backupdb. Does it exist?
3/21/09 5:51:10 PM mds[21] (/Volumes/500 Gigger/.Spotlight-V100/Store-V1/Stores/C3E5E22C-5296-4418-B36C-F364D997C440)(Er ror) IndexStore in SIStoreDirytySDBChunks:Error storing dirty sdb pages: 30
3/21/09 5:51:15 PM /System/Library/CoreServices/backupd[165] Backup failed with error: Couldn't get info on the target volume.PJGNC wrote:
3/21/09 5:51:09 PM mds[21] (/Volumes/500 Gigger/.Spotlight-V100/Store-V1/Stores/C3E5E22C-5296-4418-B36C-F364D997C440)(Er ror) IndexCI in ContentIndexOpenBulk:Could not open /Volumes/500 Gigger/.Spotlight-V100/Store-V1/Stores/C3E5E22C-5296-4418-B36C-F364D997C440/liv e.0.; needs recovery
This isn't a TM message. It's from process mds (MetaDataSearch) which is associated with Spotlight, among other things. But it does look like that disk could use a +Repair Disk+ via Disk Utility (in Applications/Utilities)
3/21/09 5:51:10 PM /System/Library/CoreServices/backupd[165] Error (-35): Getting volume path
3/21/09 5:51:10 PM /System/Library/CoreServices/backupd[165] Couldn't initialize backup volume from path: /Volumes/1TBTM
3/21/09 5:51:10 PM /System/Library/CoreServices/backupd[165] Error (-35): Couldn't get library parent ref /Volumes/1TBTM/Backups.backupdb. Does it exist?
3/21/09 5:51:15 PM /System/Library/CoreServices/backupd[165] Backup failed with error: Couldn't get info on the target volume.
These are from TM (the backupd process). I've not seen these messages. I'd also do a +Repair Disk+ on it.
And there's an easier way to see what TM backups are doing. Download the +Time Machine Buddy+ widget. It shows the messages from your logs for one TM backup run at a time, in a small window, without all the other gibberish. -
Whenever I use the help menu in any programme in my new 17" MacBook Pro and it has to go and look it up somewhere I get a long spinning ball and then this message.....
*Connection Failed*
The server may not exist or it is not operational at this time. Check the server name or IP address and your network connection and try again.
I press OK & it then loads the help page..... !
Provided I keep open the help page there is then no problem with speed.
The same thing was happening with my previous Powerbook. It is the 3 minute wait that is irksome. Then the failure message before getting my answer. I have not bothered to try & fix this over the years, but now I'm older and less patient...
How do I check the server name or IP address & where would I put it to correct this.....
Ror is online now Report Post Edit/Delete MessageThanks, Barry, but it is the same wherever I am connected. .....and all other communications are working normally.
My question still remains.... how do I check this IP address & where is it in my computer? ....and what should the IP address be? -
Hi,
I am using Windows 8.1
I have an External Hard Disk i have partitioned it to 4 parts.
One drive is now inaccessible due to sudden power failure while listening Music from that drive few days ago.
Now it shows "Data error (Cyclic redundancy check)".
I tried all the procedures provided here like
chkdsk /f, diskpart, rescan etc
but no result :( (i mean all processes failed. They could not detect the drive).
Please help me to get those data, pictures and project files.
thank youThen why aren't you posting this in the Windows 8 forums found @
http://social.technet.microsoft.com/Forums/windows/en-US/home?category=w8itpro
This is a Windows 7 forum for discussion about Windows 7.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. ” -
Inter-Company Purchasing Failure,B12B1 screnario
I Build & Run B12B1 with B1iSN 2007 and is under testing.
B1PO2B1SO
- Create a purchase order in Subsidiary Company, Choose the vendor as Headquarter.
However, the following error has occurred.
SAP B1iSN Addmin Console >Monitoring>Message Log
Failure
com.sap.b1i.xcellerator.XcelleratorException: XCE001 Nested exception: com.sap.b1i.bizprocessor.BizProcException: BPE001 Nested exception: com.sap.b1i.xcellerator.XcelleratorException: XCE001 Nested exception: com.sap.b1i.xcellerator.XcelleratorException: XCE001 Nested exception: java.lang.RuntimeException: DI Error Code: -5002 (-5002) Enter name of Business Place and VAT Registration No.(nnn-nn-nnnnn)
Do not know what the problem is.
Please help me.
Korea is the type of database.Hi,
Just check with your LPE. Business Place on marketing is mandotary fied in your localization. Thus please follow the steps below:
1.Uncompress the BizPacakge-B12B1.zip
2.Update the transformation stye sheet for biu.Z.B1PO2B1SO.xsl: Just add Business place below into the document header. You can refer to the attached.
<!--For Korean localization: Business Place and VAT Registration are mandatory-->
<BPL_IDAssignedToInvoice>
<xsl:value-of select="BPL_IDAssignedToInvoice"/>
</BPL_IDAssignedToInvoice>
3.Compress it again.
4.Import the BizPackage with B1i Control Center again.
Your LPE may talk to you soon. Just now I already have a concall with him to show how to do it.
Regards, yatsea -
Imminent hard drive failure message
can i return my laptop to the store for a replacement.. it is less than 5 months old and i am getting an imminent hard drive failure message. totally unacceptable
HP will replace the hard drive under warranty. Not too many stores will permit a return after 5 mos. We can also assist with a hard drive replacement.
-
Multiple iMac LogicBoard failures
So 3 years ago I took the plunged and converted the house to Macs. Nice experience generally. Yet in the last 2 months I have had two logicboard failures on two iMacs. The cost to fix these was quoted at over $1,000 each computer. Obviously given the age of the machines, this is not a viable fix.
I am now considering moving back to PC's (my 3 year old Mac laptop is also playing up).
After logicboard failure #1, I reluctantly forked out $2K for a new machine. I racked this up as a "bad" and unusual unit. #2 comes along and fails and it makes me mad. Worse, no sympathy from the guys in the Apple Store. I ask "Surely for a machine of this age, noone would possibly pay for a $1K logicboard? Isn't this priced to basically make you buy a new machine?" All I got back was smiles (they really didn't care it seems).
Question:
- Are Mac's prone to hardware failures?
- If they do get hardware failures are you basically just in trouble given the absurd component prices to fix ($700 for the logicboard part alone)? How can Apple justify $700 for a logicboard part?
- Does Apple offer any discounts to people who have had these multiple bad experiences? (I'm partly kidding here, but also hoping)
My Mac laptop is playing up so I may be two Mac's down. I am considering going back to the darkside now and buying PC's again.
Anyone got any comments?
ThanksThat a UPS unit would have prevented your logic board failures. Properly designed power supplies do not need a UPS unit in this country. In some third world countries where the power is unreliable on a daily basis with large power swings, they are a must have.
In my opinion, the G5 iMac's were a poor design with inadequate heat dissipation, weak power supplies and logic boards. Most of them ran for years, but an inordinate number of them had multiple failures. The new aluminum models are a much better design with most of the high heat components located at the top of the machine.
I had no hardware problems with my eight year old Dell...but I'm still sticking with Apple because of their superior software performance.
Good luck with what ever you decide...virg -
Multiple Hard Drive Failures on my Macbook Pro - Entourage reminders?
Over the past 2 months I've had three hard drives fail on three different macbook pro computers.
I've retraced my steps, searched many forums, and spoken with multiple Mac Geniuses but still can't figure out what's happening. The IT guy at work is about to kill me and I really want to figure out what's going wrong so I can fix it (or change my current behaviors).
Computer #1 - Out of the box, 2-3 weeks old. I took the computer home to do some work over the weekend. I didn't turn the it off before transporting it, but I did wait for it to go to sleep completely (I've since read that it takes a few moments while things in RAM switch over to the Hard Drive to save incase of power failure). I worked on it a bit at home, mostly just internet searches and a few word documents. When I returned to work my computer was running slowly and suddenly all of the programs locked. Since I've had this problem before with my personal computer (a G4 Powerbook), I tried the force quit options to no avail so I just held down the power key to power off. When I rebooted I got the dreaded "no" symbol.
Computer 2: IT gave me a used macbook pro that they repurposed for me. I made sure to shut down before transporting this computer. A few days later, before I even got to transfer all of my files, the computer started running slowly, programs locked. I eventually got the computer to shut itself down (as IT didn't want me to do a forced reboot) but upon restarting I got an even more dreaded screen, the folder with a question mark in it.
Computer 3: It was a fairly new computer, though a bit more ram, and probably only a few months old (used by a freelancer). It worked great. I took it home several times, transfered all of my files. Set up everything perfectly. Three weeks in, after working at my desk for about 4 hours, everything began to slow down. I called IT immediately and remotely sent a force shut down message. Nothing happened for about 15 minutes so I left for a meeting. I came back a few hours later and my computer was off. When it restarted, nothing appeared. There wasn't a "no" symbol or folder with a question mark in it, just a blank screen.
I've read and thought about all of the options.
- Large Magnet somewhere - It would have affected my personal computer (if at home) or my colleagues (if at work) or everyone else in nyc (while on the subway)
- Too hot - Possible I suppose, but how does running iTunes, powerpoint, and entourage do this?
- Downloaded something/Virus - We don't have administrative privileges. I can only update some software and send/receive folders. Plus, can any single file cause this much damage?
- Moved before asleep - This might have happened on the first computer, but I doubt it could happen to three. I always shut it down now before transporting, and I was sitting at my desk for hours before I had any trouble last time.
The one common factor that I haven't mentioned.
We use Entourage as a mail client here.
Each time the computer froze, the first things to freeze were the Entourage calendar reminders. Entourage seems to run strangely with the airport, but not with our LAN. When my computer froze last time, I had the aiport on but was working off the LAN. Could Entourage cause this much trouble? Has anyone else had trouble with entourage calendar reminders or failing hard drives?
Oh, and it also always happens on a Monday. I've taken the computers home multiple times though, so I'm not sure if it's something I'm doing during the transport or not, but the computer is always off now when I move it. I also cary my personal computer with me often, same routes and bags, so I'm not sure why it's not affected.
Thankscolumbus new boy wrote:
How crap is that?
It's not crap at all.
It's not that simple. For example, I've 3500 songs on my MacBook but don't want them all on my phone, so I have to manually select each song again???
There has to be a solution.
Why not simply make a playlist with the songs you want on the iPhone?
and maintain a current backup of your computer. -
Tried to restore my ipod classic on a windows computer... there was some sort of failure and it is now stuck in "disk mode." The ipod is no longer being recognized by itunes.
I am having the exact same problem. My ipod has been stuck in disk mode for over two hours and now itunes is frozen.
-
In case of Control File Failure, Create Control File cmd how get scn?
The following lines i picked from the
http://asktom.oracle.com/pls/asktom/f?p=100:11:0::::P11_QUESTION_ID:5033895918209
======================================================
1. We can use the 'alter database rename ' at mount stage to rename any datafile. Or is it not possible to rename the system datafile like this? Why?
2. What happens to the SCN information in the controlfile when a controlfile is recreated? How will the database sync the SCN with that of the datafiles?
If I issue a 'backup controlfile to <file>' at 8 am and then restore that controlfile binary backup at 10 am and try to open the database, it will give me a control file old error. I understand that it is because the SCN is not in sync. But if I issue a 'backup controlfile to trace' at 8 am and use that script to recreate a new controlfile at 10 am, why doesn't I get the error? Where does it get the SCN information then?
So what is the use of taking a binary copy of the controlfile. Looks like having a 'backup controlfile to trace' script is better than a binary backup. Do you agree? Why/whynot?
Followup August 16, 2002 - 2pm US/Eastern:
1) you could but I just always did it with the create controlfile statement.
When moving system -- I do it that way
When moving ANY OTHER tablespace -- i just offline it, move the files, rename the files online it.
2) it just happens.
The control file you create will read the files to figure out what is up.
I agree, I've never used a binary controlfile backup myself.
=========================================================
My Question- In the Point2 above "Where does it get the SCN information and how control file do SCN Sync with data files?
"1. The CREATE CONTROLFILE reads SCNs from the DataFiles. If the
database was last shutdown, all the datafiles are "non-fuzzy" and have the same
SCN (as of the shutdown checkpoint), If the database or some of the files are from
are hot backup, you cannot open the database because the SCN of some files is
older (lower) than others -- that is why a RECOVER (DATABASE or DATAFILE) is
required.
See http://web.singnet.com.sg/~hkchital/Incomplete_Recovery_with_BackupControlfile.doc
2. I'm not sure I agree with Tom Kyte's response
"I agree, I've never used a binary controlfile backup myself. "
to the question
"So what is the use of taking a binary copy of the controlfile. Looks like having a 'backup controlfile to trace' script is better than a binary backup. Do you agree? Why/whynot?"
If you have lost your database (storage/filesystem failure) and all your datafiles are lost,
you cannot simply do a CREATE CONTROLFILE from a Trace -- because the
CREATE CONTROLFILE has to read and verify all the datafiles specified in the
CREATE statement. If you have an RMAN Repository, you can use that to restore
your database files but otherwise, the RMAN information about backups and backupsets
are in the binary controlfile.
That is why it is important to take binary controlfile backups either manually or
using RMAN or using CONFIGURE CONTROLFILE AUTOBACKUP ON. -
Hi SAP Gurus,
We are configuring the CIN Settings for our client and at the time of testing, while saving the Out going excise invoice the system is giving the error as “Balance in Transaction Error” and when pressed enter the system displays the error as “ system failure during locking GL account 5555 by 13113910.”
We have configured Out going excise duty condition types in the SD pricing procedure
and
also maintained the same condition types as mentioned below in the path IMG / LOGISTICS GENERAL / TAX ON GOODS MOVEMENT / INDIA / BASIC SETTINGS/ DETERMINATION OF EXCISE DUTY / MAINTAIN EXCISE DEFAULTS
under the headings
AR BED Cond – JEXP
AR Cess Cond – JECS
ECS AR – JHEC
And also maintained the settings in the Path IMG / LOGISTICS GENERAL / TAX ON GOODS MOVEMENT / INDIA / SPECIFY EXCISE ACCOUNTS PER EXCISE TRANSACTION and also in SPECIFY G/L ACCOUNTS PER EXCISE TRANSACTION .
But still the above mentioned error is comming.
Note : error in not coming when I am removing the JHEC condition type from the path IMG / LOGISTICS GENERAL / TAX ON GOODS MOVEMENT / INDIA / BASIC SETTINGS/ DETERMINATION OF EXCISE DUTY / under the heading ECR AR, But we need the JHEC(ie. Higher education cess) also in out going excise invoice.
Please let me know what is the issue and how to resolve it.
Thanks & Regards
ShashiDear We faced the same issue and almost for 20 days to get it resolved.
For this kind of error firstly Check have you activated the Liable for AT1 indicator in(IMG>>Log.General>>Tax on goods Movement>>India>>Basic Settings>>Maintain Excise registrations)
Also Have you assigned Proper GL account in (IMG>>Log.General>>Tax on Good Movement>>>India>>>Account Determination>>Account determination per Excise transaction type.
Here pl check the relevant GL has been assigned for
1.RG23A BED(for Both incoming and outgoing excise invoice updations against your ETT)
2 RG23C BED, (for Both incoming and outgoing excise invoice updations against your ETT)
3 .OFF SET,(for Both incoming and outgoing excise invoice updations against your ETT)
4 MODVAT.CLEARING, (for Both incoming and outgoing excise invoice updations against your ETT)
5 PLA BED& AED & SED,(for Both incoming and outgoing excise invoice updations against your ETT at the time of utilizations)
6 PLA CESS(for Both incoming and outgoing excise invoice updations against your ETT at the time of utilizations)
7 CENVAT ON HOLD(for Both incoming and outgoing excise invoice updations against your ETT at the time of utilizations)
8.CENVAT SUSPENSE(for Both incoming and outgoing excise invoice updations against your ETT at the time of invoice posting)
9.PLA ON HOLD((for Both incoming and outgoing excise invoice updations against your ETT at the time of TR6c)
10. CENVAT REVERSAL(For cancellations vs ETT)
11. RG23A ECS(for Both incoming and outgoing excise invoice updations against your ETT)
12. RG23C ECS(for Both incoming and outgoing excise invoice updations against your ETT)
13. PLA ECS(for Both incoming and outgoing excise invoice updations against your ETT )
14. RG23A AT1(check this more carefully)
15. RG23C AT1(check this more carefully)
16. PLA AT1(check this more carefully)
Hope this helps you...
Phanikumar -
Toshiba Satellite L650-07U, Hard disk failure and replacement
Hi all,
I have Toshiba Satellite L650-07U Laptop, Model: PSK1EC-0700Q with 4GB RAM, 650GB HD, Windows 7 Home Premium installed. At the time of first use, i made Recovery DVDs which took 4 blank DVDs using Recovery media creator.
From 2 weeks it is giving problem, at start its slowdown with every application, then suddenly it started Hard disk failure error and ask to backup important files. From that instant i did all my backup save in another portable Hard drive.
I had hiren boot CD, and ran RAM test and found it OK, and then run Hard Disk test and found few bad sectors at few certain point, As 650GB Hard disk was taking alot time of time for checking bad sectors, so i stopped that application.
First I tried Recovery DVDs to restore Windows, but it failed as Laptop DVD-Writer was unable to boot from those created DVDs (DVDs are OK as had checked it on Desktop computer DVD-ROM), Laptop DVD-Writer is also working as I test few more bootable CDs and it booted perfectly, but it is not booting from Recovery DVDs.
Than i tried to restore from Recovery partition using Factory restore settings, it erases all data and reinstall new and fresh copy of Windows 7 Home Premium. It works fine for few hours than again pops up Hard Disk Failure message again and again. I searched here in Toshiba Forum and have found similar problem with other members and finally decided that it need to replace Hard Disk with new one. As It is now two and a half month old, thats why i need to buy new Hard Disk for my Laptop.
I checked all partitions of drive using Hiren Boot CD, and had found that there are four default partitions in Toshiba original laptop drive,
One hidden partition of 1.5 GB
One hidden partition of almost 21 GB
One hidden partition of almost 12 GB
One partition of 561 GB, which was the original partition where windows 7 was installed along with all of my Data.
Now I want to replace faulty drive with a new one and have a lot of question in my mind which I need to share with you guys.
At the time of first use I installed Windows 7 64 bit edition, and made Recovery DVDs, and at second time of restore to factory setting I had installed Windows 7 32 bit. I have confusion about recovery DVDs (which is not booting from default DVD-Writer of Laptop), either it has 64 Bit recovery data or 32 bit? Or have both 64 and 32 bit Data.
Toshiba restore to factory setting without using any recovery DVD/USB is the best possible way to restore Windows 7, How can I make same recover hidden partitions from original/faulty hard drives to new hard drive partitions? Is this possible and how?
On Default hard drive there was one partition of 561GB instead of two or more partitions. Is this possible to split partitions in new hard drives instead of one big partition?
As Recovery DVDs are not able to boot from laptop default DVD-Writer, is it possible to open those DVDs on another System and copy tem in USB drive and use it for booting? If it is possible than please show me the steps for making bootable USB from these Recovery DVDs.
Thanks,
masterleous
Solved!
Go to Solution.Satellite L650-07U (PSK1EC-07U00Q)
This site is for US computers. I doubt you'll get your questions for that Canadian model answered here.
There appear to be two recovery partitions. Maybe one for 32- and one for 64-bit Windows. Or maybe one is for English and the other for French.
Your User's Manual isn't much help either. You probably need to ask Toshiba tech support in Canada.
About all I have to offer is this: Be wary of drives with advanced-format technology. See my message about that.
-Jerry -
HDD failure, I'd like to know how to get Windows 7 back on it.
Hello everyone, I've had a HDD issue lately, but before I move on to describe my issue, here are the specs of my notebook:
HP Pavilion dv6-3264ca
AMD Triple-Core CPU 2.2 Ghz
6GB RAM
128MB ATI Graphic Card
750GB Toshiba HDD
Windows 7 64-bit
The issue:
Recently I've had a very unfortunate HDD failure. The recovery partition wouldn't even load. I tried booting my notebook on Linux with the HDD still attached, and it wouldn't read. I extracted the HDD and placed it in an HDD-enclosuer and it still wouldn't load on Windows XP or Vista or 7. It would however read in the device manager of Windows and also in the BIOS.
I needed to extract some high-priority data from there so I managed to retrieve all my data safely through a data recovery service, but now the drive is rendered useless. I was told a low-level format might be able to help it be usable again, and if that were to happen, the recovery partition would then be removed in the process.
In addition to that, I would like to install Windows 7 64-bit onto the drive, but the notebook box did not come with an installation CD, which is quite frustrating. Is there any way HP can let me download Windows 7 through some warranty service?
I have a one-year warranty on my laptop.
So in closing, I would like to know if I can get Windows 7 back onto my HDD for free, or if I need to go about buying Windows 7 again.
Any advice from you kind folks?
This question was solved.
View Solution.Hi,
Here are Two options.
1. If you have ( or can borrow ) a retail Windows 7 installation disc that is exactly the same version as your OEM installation - ie if your notebook came with Windows 7 Home Premium 64bit this is the exact retail version you would need.
If you don't have access to a retail disc, you can create an installation disc yourself - just download the correct Disc Image from the link below and use an application such as ImgBurn to burn the ISO correctly to a blank DVD.
http://www.mydigitallife.info/download-windows-7-iso-official-32-bit-and-64-bit-direct-download-link...
Use the disc to perform the installation, enter the Windows activation key found on the underside of your notebook when requested and when the installation has completed, use the 'Phone Method' detailed in the link below to activate the OS - this method supported by Microsoft and is popular with people who just want a clean installation of Windows 7 without the additional software load normally bundled with OEM installations.
http://www.kodyaz.com/articles/how-to-activate-windows-7-by-phone.aspx
Any additional drivers you may need can be found Here.
2. You can order a replacement set of Recovery Discs using the link below - these cost around $30 if you live in the US.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00810334&cc=us&lc=en&dlc=en
If you have any problem with this link, order them directly from HP.
If you live in the US, contact HP Here.
If you are in another part of the world, start Here.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience -
Desktop freezes and hard drives failure
Hey i faced a recent problem with my Computer, when i log in it freezes/crash i got told its due to my sound drive failuring, i tryed to download HP assistant to upgrade my sound drive but it cames up saying " Error 1719. windows installer service could not be accessed" I went to the HP software website to see if theres any sound drive but there arnt. I cant do a system restore because an error pops up. I tryed everything, nothing seems not to work .
Heres my computer specs
Im in safe mod if u want to know ^ ^
System Information
Time of this report: 4/29/2011, 14:11:56
Machine name: ASHDOWN-PC
Operating System: Windows 7 Home Premium 32-bit (6.1, Build 7601) (7601.win7sp1_rtm.101119-1850)
Language: English (Regional Setting: English)
System Manufacturer: Compaq-Presario
System Model: KQ318AA-ABU SR5414UK
BIOS: v5.03
Processor: Intel(R) Core(TM)2 Duo CPU E4600 @ 2.40GHz (2 CPUs), ~2.4GHz
Memory: 2048MB RAM
Available OS Memory: 2046MB RAM
Page File: 556MB used, 3536MB available
Windows Dir: C:\Windows
DirectX Version: DirectX 11
DX Setup Parameters: Not found
User DPI Setting: Using System DPI
System DPI Setting: 96 DPI (100 percent)
DWM DPI Scaling: Disabled
DxDiag Version: 6.01.7600.16385 32bit Unicode
DxDiag Previously: Crashed in system information (stage 4). Re-running DxDiag with "dontskip" command line parameter or choosing not to bypass information gathering when prompted might result in DxDiag successfully obtaining this information
DxDiag Notes
Display Tab 1: No problems found.
Sound Tab 1: This computer cannot play audio because the Windows Audio service is not enabled. Use the Sounds and Devices Properties control panel to enable audio. No sound card was found. If one is expected, you should install a sound driver provided by the hardware manufacturer.
Input Tab: No problems found.
DirectX Debug Levels
Direct3D: 0/4 (retail)
DirectDraw: 0/4 (retail)
DirectInput: 0/5 (retail)
DirectMusic: 0/5 (retail)
DirectPlay: 0/9 (retail)
DirectSound: 0/5 (retail)
DirectShow: 0/6 (retail)
Display Devices
Card name:
Manufacturer:
Chip type:
DAC type:
Device Key: Enum\
Display Memory: n/a
Dedicated Memory: n/a
Shared Memory: n/a
Current Mode: 1600 x 1200 (32 bit) (1Hz)
Driver Name:
Driver File Version: ()
Driver Version:
DDI Version: unknown
Driver Model: unknown
Driver Attributes: Final Retail
Driver Date/Size: , 0 bytes
WHQL Logo'd: n/a
WHQL Date Stamp: n/a
Device Identifier: {D7B70EE0-4340-11CF-B123-B03DAEC2CB35}
Vendor ID: 0x0000
Device ID: 0x0000
SubSys ID: 0x00000000
Revision ID: 0x0000
Driver Strong Name: Unknown
Rank Of Driver: Unknown
Video Accel:
Deinterlace Caps: n/a
D3D9 Overlay: n/a
DXVA-HD: n/a
DDraw Status: Not Available
D3D Status: Not Available
AGP Status: Not Available
Sound Devices
Description:
Default Sound Playback: No
Default Voice Playback: No
Hardware ID:
Manufacturer ID:
Product ID:
Type:
Driver Name:
Driver Version:
Driver Attributes:
WHQL Logo'd:
Date and Size:
Other Files:
Driver Provider:
HW Accel Level: Emulation Only
Cap Flags: 0x0
Min/Max Sample Rate: 0, 0
Static/Strm HW Mix Bufs: 0, 0
Static/Strm HW 3D Bufs: 0, 0
HW Memory: 0
Voice Management: No
EAX(tm) 2.0 Listen/Src: No, No
I3DL2(tm) Listen/Src: No, No
Sensaura(tm) ZoomFX(tm): No
Sound Capture Devices
DirectInput Devices
Device Name: Mouse
Attached: 1
Controller ID: n/a
Vendor/Product ID: n/a
FF Driver: n/a
Device Name: Keyboard
Attached: 1
Controller ID: n/a
Vendor/Product ID: n/a
FF Driver: n/a
Device Name: Razer Arctosa
Attached: 1
Controller ID: 0x0
Vendor/Product ID: 0x1532, 0x010B
FF Driver: n/a
Device Name: Razer Arctosa
Attached: 1
Controller ID: 0x0
Vendor/Product ID: 0x1532, 0x010B
FF Driver: n/a
Poll w/ Interrupt: No
USB Devices
+ USB Root Hub
| Vendor/Product ID: 0x8086, 0x27C9
| Matching Device ID: usb\root_hub
| Service: usbhub
|
+-+ USB Input Device
| | Vendor/Product ID: 0x1532, 0x001C
| | Location: Port_#0002.Hub_#0002
| | Matching Device ID: generic_hid_device
| | Service: HidUsb
| |
| +-+ HID-compliant mouse
| | | Vendor/Product ID: 0x1532, 0x001C
| | | Matching Device ID: hid_device_system_mouse
| | | Service: mouhid
Gameport Devices
PS/2 Devices
+ HID Keyboard Device
| Vendor/Product ID: 0x1532, 0x010B
| Matching Device ID: hid_device_system_keyboard
| Service: kbdhid
|
+ Terminal Server Keyboard Driver
| Matching Device ID: root\rdp_kbd
| Upper Filters: kbdclass
| Service: TermDD
|
+ Terminal Server Mouse Driver
| Matching Device ID: root\rdp_mou
| Upper Filters: mouclass
| Service: TermDD
System Devices
Name: Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27CA
Device ID: PCI\VEN_8086&DEV_27CA&SUBSYS_2A78103C&REV_01\3&2411E6FE&1&EA
Driver: n/a
Name: Intel(R) G33/G31/P35/P31 Express Chipset PCI Express Root Port - 29C1
Device ID: PCI\VEN_8086&DEV_29C1&SUBSYS_29C18086&REV_10\3&2411E6FE&1&08
Driver: n/a
Name: Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27C9
Device ID: PCI\VEN_8086&DEV_27C9&SUBSYS_2A78103C&REV_01\3&2411E6FE&1&E9
Driver: n/a
Name: Intel(R) G33/G31/P35/P31 Express Chipset Processor to I/O Controller - 29C0
Device ID: PCI\VEN_8086&DEV_29C0&SUBSYS_2A78103C&REV_10\3&2411E6FE&1&00
Driver: n/a
Name: Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27C8
Device ID: PCI\VEN_8086&DEV_27C8&SUBSYS_2A78103C&REV_01\3&2411E6FE&1&E8
Driver: n/a
Name: Intel(R) 82801G (ICH7 Family) SMBus Controller - 27DA
Device ID: PCI\VEN_8086&DEV_27DA&SUBSYS_2A78103C&REV_01\3&2411E6FE&1&FB
Driver: n/a
Name: Intel(R) 82801GB/GR/GH (ICH7 Family) Serial ATA Storage Controller - 27C0
Device ID: PCI\VEN_8086&DEV_27C0&SUBSYS_2A78103C&REV_01\3&2411E6FE&1&FA
Driver: n/a
Name: High Definition Audio Controller
Device ID: PCI\VEN_8086&DEV_27D8&SUBSYS_2A78103C&REV_01\3&2411E6FE&1&D8
Driver: n/a
Name: Intel(R) 82801GB/GR (ICH7 Family) LPC Interface Controller - 27B8
Device ID: PCI\VEN_8086&DEV_27B8&SUBSYS_2A78103C&REV_01\3&2411E6FE&1&F8
Driver: n/a
Name: Intel(R) 82801G (ICH7 Family) PCI Express Root Port - 27D0
Device ID: PCI\VEN_8086&DEV_27D0&SUBSYS_2A78103C&REV_01\3&2411E6FE&1&E0
Driver: n/a
Name: Intel(R) 82801 PCI Bridge - 244E
Device ID: PCI\VEN_8086&DEV_244E&SUBSYS_2A78103C&REV_E1\3&2411E6FE&1&F0
Driver: n/a
Name: Intel(R) 82801G (ICH7 Family) USB2 Enhanced Host Controller - 27CC
Device ID: PCI\VEN_8086&DEV_27CC&SUBSYS_2A78103C&REV_01\3&2411E6FE&1&EF
Driver: n/a
Name: Realtek RTL8101E Family PCI-E Fast Ethernet NIC (NDIS 6.20)
Device ID: PCI\VEN_10EC&DEV_8136&SUBSYS_2A78103C&REV_01\4&3601B127&0&00E0
Driver: n/a
Name: Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27CB
Device ID: PCI\VEN_8086&DEV_27CB&SUBSYS_2A78103C&REV_01\3&2411E6FE&1&EB
Driver: n/a
Name: NVIDIA GeForce 9600 GT
Device ID: PCI\VEN_10DE&DEV_0622&SUBSYS_82A11043&REV_A1\4&1EA08276&0&0008
Driver: n/a
DirectShow Filters
DirectShow Filters:
WMAudio Decoder DMO,0x00800800,1,1,WMADMOD.DLL,6.01.7600.16385
WMAPro over S/PDIF DMO,0x00600800,1,1,WMADMOD.DLL,6.01.7600.16385
WMSpeech Decoder DMO,0x00600800,1,1,WMSPDMOD.DLL,6.01.7600.16385
MP3 Decoder DMO,0x00600800,1,1,mp3dmod.dll,6.01.7600.16385
Mpeg4s Decoder DMO,0x00800001,1,1,mp4sdecd.dll,6.01.7600.16385
WMV Screen decoder DMO,0x00600800,1,1,wmvsdecd.dll,6.01.7600.16385
WMVideo Decoder DMO,0x00800001,1,1,wmvdecod.dll,6.01.7600.16597
Mpeg43 Decoder DMO,0x00800001,1,1,mp43decd.dll,6.01.7600.16385
Mpeg4 Decoder DMO,0x00800001,1,1,mpg4decd.dll,6.01.7600.16385
WMT VIH2 Fix,0x00200000,1,1,WLXVAFilt.dll,15.04.3508.1109
Record Queue,0x00200000,1,1,WLXVAFilt.dll,15.04.3508.1109
WMT Switch Filter,0x00200000,1,1,WLXVAFilt.dll,15.04.3508.1109
WMT Virtual Renderer,0x00200000,1,0,WLXVAFilt.dll,15.04.3508.1109
WMT DV Extract,0x00200000,1,1,WLXVAFilt.dll,15.04.3508.1109
WMT Virtual Source,0x00200000,0,1,WLXVAFilt.dll,15.04.3508.1109
WMT Sample Information Filter,0x00200000,1,1,WLXVAFilt.dll,15.04.3508.1109
DV Muxer,0x00400000,0,0,qdv.dll,6.06.7600.16385
Color Space Converter,0x00400001,1,1,quartz.dll,6.06.7600.16490
WM ASF Reader,0x00400000,0,0,qasf.dll,12.00.7600.16385
DivX AAC Decoder,0x00800000,1,1,daac.ax,7.01.0000.0010
Screen Capture filter,0x00200000,0,1,wmpsrcwp.dll,12.00.7600.16385
AVI Splitter,0x00600000,1,1,quartz.dll,6.06.7600.16490
VGA 16 Color Ditherer,0x00400000,1,1,quartz.dll,6.06.7600.16490
SBE2MediaTypeProfile,0x00200000,0,0,sbe.dll,6.06.7600.16724
Microsoft DTV-DVD Video Decoder,0x005fffff,2,4,msmpeg2vdec.dll,6.01.7140.0000
AC3 Parser Filter,0x00600000,1,1,mpg2splt.ax,6.06.7600.16724
StreamBufferSink,0x00200000,0,0,sbe.dll,6.06.7600.16724
Microsoft TV Captions Decoder,0x00200001,1,0,MSTVCapn.dll,6.01.7600.16385
MJPEG Decompressor,0x00600000,1,1,quartz.dll,6.06.7600.16490
CBVA DMO wrapper filter,0x00200000,1,1,cbva.dll,6.01.7600.16385
MPEG-I Stream Splitter,0x00600000,1,2,quartz.dll,6.06.7600.16490
SAMI (CC) Parser,0x00400000,1,1,quartz.dll,6.06.7600.16490
VBI Codec,0x00600000,1,4,VBICodec.ax,6.06.7600.16385
MPEG-2 Splitter,0x005fffff,1,0,mpg2splt.ax,6.06.7600.16724
Closed Captions Analysis Filter,0x00200000,2,5,cca.dll,6.06.7600.16385
SBE2FileScan,0x00200000,0,0,sbe.dll,6.06.7600.16724
Microsoft MPEG-2 Video Encoder,0x00200000,1,1,msmpeg2enc.dll,6.01.7600.16385
DivX MKV Demux (unrestricted),0x00200000,0,1,DMFSource.ax,1.00.0002.0006
Internal Script Command Renderer,0x00800001,1,0,quartz.dll,6.06.7600.16490
MPEG Audio Decoder,0x03680001,1,1,quartz.dll,6.06.7600.16490
DV Splitter,0x00600000,1,2,qdv.dll,6.06.7600.16385
Video Mixing Renderer 9,0x00200000,1,0,quartz.dll,6.06.7600.16490
Microsoft MPEG-2 Encoder,0x00200000,2,1,msmpeg2enc.dll,6.01.7600.16385
ACM Wrapper,0x00600000,1,1,quartz.dll,6.06.7600.16490
Video Renderer,0x00800001,1,0,quartz.dll,6.06.7600.16490
MPEG-2 Video Stream Analyzer,0x00200000,0,0,sbe.dll,6.06.7600.16724
Line 21 Decoder,0x00600000,1,1,qdvd.dll,6.06.7600.16385
Video Port Manager,0x00600000,2,1,quartz.dll,6.06.7600.16490
DivX H.264 Decoder,0x00800000,1,1,DivXDecH264.ax,9.00.0001.0021
Video Renderer,0x00400000,1,0,quartz.dll,6.06.7600.16490
File Writer,0x00200000,1,0,WLXVAFilt.dll,15.04.3508.1109
DivX Decoder Filter,0x00800000,1,1,DivXDec.ax,7.01.0001.0014
VPS Decoder,0x00200000,0,0,WSTPager.ax,6.06.7600.16385
WM ASF Writer,0x00400000,0,0,qasf.dll,12.00.7600.16385
VBI Surface Allocator,0x00600000,1,1,vbisurf.ax,6.01.7600.16385
File writer,0x00200000,1,0,qcap.dll,6.06.7600.16385
iTV Data Sink,0x00600000,1,0,itvdata.dll,6.06.7600.16385
iTV Data Capture filter,0x00600000,1,1,itvdata.dll,6.06.7600.16385
DVD Navigator,0x00200000,0,3,qdvd.dll,6.06.7600.16385
Microsoft TV Subtitles Decoder,0x00200001,1,0,MSTVCapn.dll,6.01.7600.16385
Overlay Mixer2,0x00200000,1,1,qdvd.dll,6.06.7600.16385
DivX MKV Demux,0x00600000,0,1,DMFSource.ax,1.00.0002.0006
AVI Draw,0x00600064,9,1,quartz.dll,6.06.7600.16490
RDP DShow Redirection Filter,0xffffffff,1,0,DShowRdpFilter.dll,
Microsoft MPEG-2 Audio Encoder,0x00200000,1,1,msmpeg2enc.dll,6.01.7600.16385
WST Pager,0x00200000,1,1,WSTPager.ax,6.06.7600.16385
MPEG-2 Demultiplexer,0x00600000,1,1,mpg2splt.ax,6.06.7600.16724
DV Video Decoder,0x00800000,1,1,qdv.dll,6.06.7600.16385
LAME Audio Encoder,0x00100000,2,1,lame.ax,1.00.0054.50801
SampleGrabber,0x00200000,1,1,qedit.dll,6.06.7600.16385
Null Renderer,0x00200000,1,0,qedit.dll,6.06.7600.16385
MPEG-2 Sections and Tables,0x005fffff,1,0,Mpeg2Data.ax,6.06.7600.16385
Microsoft AC3 Encoder,0x00200000,1,1,msac3enc.dll,6.01.7600.16385
StreamBufferSource,0x00200000,0,0,sbe.dll,6.06.7600.16724
Smart Tee,0x00200000,1,2,qcap.dll,6.06.7600.16385
Overlay Mixer,0x00200000,0,0,qdvd.dll,6.06.7600.16385
AVI Decompressor,0x00600000,1,1,quartz.dll,6.06.7600.16490
NetBridge,0x00200000,2,0,netbridge.dll,6.01.7600.16385
AVI/WAV File Source,0x00400000,0,2,quartz.dll,6.06.7600.16490
Wave Parser,0x00400000,1,1,quartz.dll,6.06.7600.16490
MIDI Parser,0x00400000,1,1,quartz.dll,6.06.7600.16490
Multi-file Parser,0x00400000,1,1,quartz.dll,6.06.7600.16490
File stream renderer,0x00400000,1,1,quartz.dll,6.06.7600.16490
Microsoft DTV-DVD Audio Decoder,0x005fffff,1,1,msmpeg2adec.dll,6.01.7140.0000
StreamBufferSink2,0x00200000,0,0,sbe.dll,6.06.7600.16724
AVI Mux,0x00200000,1,0,qcap.dll,6.06.7600.16385
Line 21 Decoder 2,0x00600002,1,1,quartz.dll,6.06.7600.16490
File Source (Async.),0x00400000,0,1,quartz.dll,6.06.7600.16490
File Source (URL),0x00400000,0,1,quartz.dll,6.06.7600.16490
Media Center Extender Encryption Filter,0x00200000,2,2,Mcx2Filter.dll,6.01.7600.16385
AudioRecorder WAV Dest,0x00200000,0,0,WavDest.dll,
AudioRecorder Wave Form,0x00200000,0,0,WavDest.dll,
SoundRecorder Null Renderer,0x00200000,0,0,WavDest.dll,
Infinite Pin Tee Filter,0x00200000,1,1,qcap.dll,6.06.7600.16385
Enhanced Video Renderer,0x00200000,1,0,evr.dll,6.01.7600.16385
BDA MPEG2 Transport Information Filter,0x00200000,2,0,psisrndr.ax,6.06.7600.16385
MPEG Video Decoder,0x40000001,1,1,quartz.dll,6.06.7600.16490
WDM Streaming Tee/Splitter Devices:
Tee/Sink-to-Sink Converter,0x00200000,1,1,ksproxy.ax,6.01.7600.16385
Video Compressors:
WMVideo8 Encoder DMO,0x00600800,1,1,wmvxencd.dll,6.01.7600.16385
WMVideo9 Encoder DMO,0x00600800,1,1,wmvencod.dll,6.01.7600.16385
MSScreen 9 encoder DMO,0x00600800,1,1,wmvsencd.dll,6.01.7600.16385
DV Video Encoder,0x00200000,0,0,qdv.dll,6.06.7600.16385
MJPEG Compressor,0x00200000,0,0,quartz.dll,6.06.7600.16490
Cinepak Codec by Radius,0x00200000,1,1,qcap.dll,6.06.7600.16385
DivX 6.9.2 Codec (2 Logical CPUs),0x00200000,1,1,qcap.dll,6.06.7600.16385
Fraps Video Decompressor,0x00200000,1,1,qcap.dll,6.06.7600.16385
Intel IYUV codec,0x00200000,1,1,qcap.dll,6.06.7600.16385
Intel IYUV codec,0x00200000,1,1,qcap.dll,6.06.7600.16385
Microsoft RLE,0x00200000,1,1,qcap.dll,6.06.7600.16385
Microsoft Video 1,0x00200000,1,1,qcap.dll,6.06.7600.16385
x264vfw - H.264/MPEG-4 AVC codec,0x00200000,1,1,qcap.dll,6.06.7600.16385
DivX 6.9.2 YV12 Decoder,0x00200000,1,1,qcap.dll,6.06.7600.16385
Audio Compressors:
WM Speech Encoder DMO,0x00600800,1,1,WMSPDMOE.DLL,6.01.7600.16385
WMAudio Encoder DMO,0x00600800,1,1,WMADMOE.DLL,6.01.7600.16385
IMA ADPCM,0x00200000,1,1,quartz.dll,6.06.7600.16490
PCM,0x00200000,1,1,quartz.dll,6.06.7600.16490
Microsoft ADPCM,0x00200000,1,1,quartz.dll,6.06.7600.16490
GSM 6.10,0x00200000,1,1,quartz.dll,6.06.7600.16490
Messenger Audio Codec,0x00200000,1,1,quartz.dll,6.06.7600.16490
CCITT A-Law,0x00200000,1,1,quartz.dll,6.06.7600.16490
CCITT u-Law,0x00200000,1,1,quartz.dll,6.06.7600.16490
MPEG Layer-3,0x00200000,1,1,quartz.dll,6.06.7600.16490
PBDA CP Filters:
PBDA DTFilter,0x00600000,1,1,CPFilters.dll,6.06.7600.16724
PBDA ETFilter,0x00200000,0,0,CPFilters.dll,6.06.7600.16724
PBDA PTFilter,0x00200000,0,0,CPFilters.dll,6.06.7600.16724
Midi Renderers:
Default MidiOut Device,0x00800000,1,0,quartz.dll,6.06.7600.16490
Microsoft GS Wavetable Synth,0x00200000,1,0,quartz.dll,6.06.7600.16490
BDA Network Providers:
Microsoft ATSC Network Provider,0x00200000,0,1,MSDvbNP.ax,6.06.7600.16385
Microsoft DVBC Network Provider,0x00200000,0,1,MSDvbNP.ax,6.06.7600.16385
Microsoft DVBS Network Provider,0x00200000,0,1,MSDvbNP.ax,6.06.7600.16385
Microsoft DVBT Network Provider,0x00200000,0,1,MSDvbNP.ax,6.06.7600.16385
Microsoft Network Provider,0x00200000,0,1,MSNP.ax,6.06.7600.16648
Multi-Instance Capable VBI Codecs:
VBI Codec,0x00600000,1,4,VBICodec.ax,6.06.7600.16385
BDA Transport Information Renderers:
BDA MPEG2 Transport Information Filter,0x00600000,2,0,psisrndr.ax,6.06.7600.16385
MPEG-2 Sections and Tables,0x00600000,1,0,Mpeg2Data.ax,6.06.7600.16385
BDA CP/CA Filters:
Decrypt/Tag,0x00600000,1,1,EncDec.dll,6.06.7600.16724
Encrypt/Tag,0x00200000,0,0,EncDec.dll,6.06.7600.16724
PTFilter,0x00200000,0,0,EncDec.dll,6.06.7600.16724
XDS Codec,0x00200000,0,0,EncDec.dll,6.06.7600.16724
WDM Streaming Communication Transforms:
Tee/Sink-to-Sink Converter,0x00200000,1,1,ksproxy.ax,6.01.7600.16385
Audio Renderers:
Default DirectSound Device,0x00800000,1,0,quartz.dll,6.06.7600.16490
Default WaveOut Device,0x00200000,1,0,quartz.dll,6.06.7600.16490
EVR Power Information
Current Setting: {5C67A112-A4C9-483F-B4A7-1D473BECAFDC} (Quality)
Quality Flags: 2576
Enabled:
Force throttling
Allow half deinterlace
Allow scaling
Decode Power Usage: 100
Balanced Flags: 1424
Enabled:
Force throttling
Allow batching
Force half deinterlace
Force scaling
Decode Power Usage: 50
PowerFlags: 1424
Enabled:
Force throttling
Allow batching
Force half deinterlace
Force scaling
Decode Power Usage: 0You can make them visible on the Desktop using Finder/Preferences/General. You can also set them to show up in the Finder Sidebar using Preferences/Sidebar.
Maybe you are looking for
-
Leave approved in Portal is not getting updated in Infotype 2001
Hello, I am using the standard WF - WS12300111 for Leave Request in the Portal. The workflow is working fine in the portal; Manager could approve / reject the leave request in MSS and it is updating the portal Team calendar and ESS Employee Leave det
-
Error in converting SQL 2014 Trial to Full version using VLKey
Hi, I am currently trying to upgrade my SQL 2014 evaluation version to the full version. I have purchased a Volume License for SQL Server 2014 Server/CAL and have extracted the product key from the ISO File. I have verified this product key with the
-
Problem when passing non English text to another amx page
Hi, I'm using JDeveloper version 11.1.2.3.0 under windows 7, to deployed ADF Mobile application into android device, when i used the application to pass 3 input text value to another page (or object) i note that if passed the 3 text without any Engli
-
I have windows xp professional. I just opened my new zen mozaic last night,installed it,and opened creative centrale..and it does not open. I sent an email to creative labs and all the guy said to do is uninstall it,and then he gave me a link to a st
-
Hi Gurus, I have one issue in Rebate - Accruals are showing correctly at verification level but not capturing in Sales Volume in Rebate Agreement. Please let me know the reason for the same.