FCS on Dual 2Ghz G5?

I know Apple recommends a minimum of a G5 1.8, but I'm wondering if anyone can give me an idea of how FCS might run on a Dual 2 ghz G5?
Thanks in advance,
Larry

I have est setup of FCServ on dual G5 2 GHz Xserve. Actualy Xserve manages databes and encodes proxy only for preview (I changed proxy preset to MPEG-4 format) Software runs ok. But for advanced encoding you have to set up additional compressor cluster.
Finaly i want setup FCServ database on Intel Xserve and I think about load balance because there are about 100 FCP clients in my tv company.

Similar Messages

  • G5 dual 2ghz.  Been unplugged for a while. Powers up but no video or power to usb keyboard.  Boots up fine in safe mode, restart into normal mode ok. After shutdown, back to same issue.  What's happening?

    G5 dual 2ghz.  Been unplugged for a while. Powers up but no video or power to usb keyboard.  Boots up fine in safe mode, restart into normal mode ok. After shutdown, back to same issue.  What's happening?

    I keep seeing people ask and the advice to replace if it has been unplugged, but really have nothing to confirm that from my experiences.
    My experience is that a weak or dead battery can cause much more than date and time issues.
    I have seen it time and time again.
    Deal with used machines and you will quickly learn....
    I'll give no "recipe" or set list of symptoms, but the range of irregularities that can occur make it a quick and easy first line of troubleshooting, especially when the machine has been off the mains for a few months.
    Why fight mysterious maladies and troubleshoot with the knowledge that the PRAM battery is beyond it's useful life.
    Maybe they recharge?
    Not likely. They are chemically nasty, disposable, one way discharge batteries.
    They aren't Lithium-ion batteries

  • Power Mac G5 (Dual 2Ghz 970MP) running 10.5.8 but crashes trying to install 10.4

    Would you be able to help? I just purchased an old Power Mac G5 (late-2005, PowerMac11,2) model A1117 EMC 2023 (Dual 2Ghz, 970MP) that was running OS 10.5.8 but want to install 10.4.6 to run Classic Mode applications under 9.2.1.
    The G5 configuration is:
    1. Boot ROM - 5.2.7f1
    2. 1.5Gb DDR2 SDRAM memory
    3. 80Gb Maxtor SATA
    Booting off a Mac OS X Tiger (includes Xcode2) install DVD (2Z691-5305-A) (complete with original documentation) that I bought off eBay, the G5 has kernel crash with the following traces at startup:
    After this, I reset it by pressing power button, eject the DVD, and I'm back at 10.5.8. I don't have the original install DVD so have tried to use the full retail 10.4.6 (purportedly) version, but haven't gotten that far to verify which version it is.
    Thoughts?
    Thanks for your ideas in advance.

    I only have the GeForce 6600LE PCIe card in Slot 1. No AirPort Extreme/Bluetooth card.
    I did replace the old PRAM battery (voltage 2.94) with a new CR 2032 and reset the PRAM holding down Command-Option-P-R keys until second boot tone chimed. (A lot of dust in there, but I haven't really cleaned it yet...) After boot, I reset the date / time.
    First, I inserted the OS X 10.4 install DVD, double-clicked on the Installer icon and the G5 rebooted loading from the DVD and then, the same kernel crash as shown on the screen shots above.
    Second, I inserted the install DVD, rebooted without holding the alt key and the G5 loaded the DVD and crashed as before.
    Third, I inserted the install DVD, did nothing to open the Installer, then closed the DVD. Checked Startup Disk and none of the icons (HD, DVD, Network Startup with "?") was highlighted. I rebooted and I held the alt key at bootup and it presented me with four icons: 1) the hard drive (highlighted), 2) the DVD, 3) a clockwise arrow, and 4) an arrow facing to the right. I selected the DVD with the mouse and clicked on the right arrow. Same crash as before.
    I pressed on the eject key, rebooted, took out the DVD, and 10.5.8 booted up as normal.
    Thoughts? I have my suspicions about the DVD, but that makes no sense as it appears to be an original with documentation (Welcome to Tiger, Installation Guide, , box, etc.
    Thanks.

  • Internal SATA drives on G5 Dual 2ghz?

    Is there any difference at all between drive bay "A" and bay "B?"
    I know that we can make boot drives for either, but is there any advantage to having the primary drive be in bay "A" -vs- "B?"
    Additionally, if both are loaded with bootable systems, can the drives be swapped without any consequences? I guess I'm wondering whether there is any reason Apple puts the stock drive in bay "A." Thoughts?
    much obliged,
    Mick

    Oops! I forgot to ask one more related thing.
    These new giant 750 SATA drives, the Barracudas. Are there any limitations installing these in an "old" G5 dual 2ghz?... In other words, is my G5 still up to date enough to take advantage of the latest SATA technology? I'm having trouble sorting through the various model numbers and just wanted to know if my older hardware could still enjoy the ride.
    Anybody put in a 10,000 rpm Western Digital SATA? Is there a big speed boost? A Windows guy was suggesting a system with a small 10,000 rpm drive like that in bay A with just the system on it, and then storing applications and such on a larger SATA in Bay B. Can that be done? Is it a good idea?
    Much obliged,
    Mick

  • Dual 2GHz G5 Firewire failure

    So, last night I get home and try to boot up my external HD only to have it not show up in the OS. After about 30 panick-ridden minutes of cable and port swapping, I have come to the conclusion that the Firewire 400 has completely failed. Neither the main port on the back of the computer or the one on the front are working (consequently, the Firewire on the back of my 20" monitor isn't working either since its plugged into the main Firewire port). I am not sure about the Firewire 800 port (As I don't have any FW800 devices) but the USB DOES work.
    I assume this isn't something I can fix personally since the glossy "Gates of G5" are concealing that portion of the computer? Does anyone know how much this repair is going to cost me?
    Thanks for your time and help!
    Clo
    G5 Dual 2GHz   Mac OS X (10.4)  

    You could try a firewire reset
    "Mike Mihalik, LaCie
    Seems like the FireWire issue needs to be revisited quite often. Here is my often repeated suggestion which appears to clear up many FireWire issues: reset the FireWire ports. Panther has a Finder Preference to show mounted volumes on the Desktop. You must set this for mounted drives to be visible. Please follow these instructions to reset your FireWire port.
    http://docs.info.apple.com/article.html?artnum=88338
    Here is a summary:
    * shut down and disconnect all external drives and peripherals ; make sure nothing is connected to the FireWire ports
    * use Apple Disk Utility to repair permissions on your internal boot drive
    * shut down and disconnect the AC power from the computer as well as the drives; if laptop, also remove battery
    * let sit unpowered and unconnected for 15 minutes
    * reconnect AC power to only the computer (battery too if laptop)
    * restart computer
    * verify that FireWire ports are visible within Apple System Profiler
    * reconnect FireWire drive (only one); refresh window within Apple System Profiler to rescan the FireWire bus; confirm that drive is visible
    * confirm drive is OK by using Apple Disk Utility and apply First Aid
    * repeat for other drives, one at a time "
    Hope it helps.

  • G5 mac dual 2ghz ppc shuts down after target disc boot

    Please help. I'm trying to startup my ppc in TD mode and it shuts off after a brief showing of the firewire logo on the monitor... has anyone else seen this problem?
    thx
    a
    g5 dual 2ghz ppc   Mac OS X (10.4.8)  

    It is connected to a new intel mac pro. I'm trying to use the migration manager to transfer data. I have disconnected all other devices, and running just 1 monitor. I have taken RAM out (in a pair) in an attempt to reset the PRAM (but my keyboard commands do not work either) The only keyboard command that does work is "c"... ay ideas?

  • Dual 2ghz G5 appears with only one processor in Activity Monitor

    Here's something I haven't seen before... a dual 2ghz G5 appears as a single processor machine in Activity Monitor. I ran the hardware test from the CD and everything checked out fine. I then rebooted and zapped PRAM using commandoption+PR... I held the keys down for a while and zapped it three times. System booted up and showed both procs in Activity Monitor. Restarted system again and now shows only a single CPU.
    Anyone seen this before?
    TIA!
    G5 dual 2ghz   Mac OS X (10.4.8)  

    Did you ever use CHUD or Open Firmware to disable a cpu?
    My preference with G5s is to boot into Open Firmware and
    reset-nvram
    set-defaults
    reset-all
    which should and is easier to rebuild the device tree rather than zap pram (once is enough, older OldWorld systems urban legend was you needed multiple reboots to be sure).

  • Is the new iMac faster than my PowerMac G5 dual 2Ghz?

    I have a PowerMac G5, Dual 2Ghz (first generation model)
    2.5GB Ram, and a ATI 9800 Pro 256mb Graphics Card.
    Looking at the SPEC ratings on the Apple page, the new iMac (2.0Ghz model) scored...
    SPECint_rate2000 = 32.6
    SPECfp_rate2000 = 27.1
    And according to http://www.apple.com/lae/g5/ the dual 2Ghz scored...
    SPECint_rate2000 = 15.7
    SPECfp_rate2000 = 17.2
    Doesn't this mean is roughly twice as fast? Does SPEC just measure the processor or the whole system?
    And how does my ATI Radoen 9800 Pro 256MB compare to the ATI Radeon X1600 256MB?
    Thanks!

    I agree. Specs are great and certainly are helpful in comparing the new MacBook to the new iMac as they are quite similar. What's really interesting is how PowerPC coded apps will compare to their universal binary equivalents on the new machines. I for one am curious to see how the universal binary of FCP Studio runs on the new iMac vs today's PowerMac. While people have been using FCP tools on G5 iMacs and G4 PowerBooks, performance isn't nearly as good as the same app on a Dual or Quad G5 PowerMac. It could usher in a whole new segment of Pro tools users who can get good performance from a less expensive option like the new iMac.
    Jeff

  • My refurbished Dual 2ghz keeps panicing and crashing

    So a year ago I purchased a refurbished Dual 2ghz G5. After about 6 months, I began getting kernal panics more frequently. When I tried to use disc utility, it kept getting an error in repairing the disc. So I erased and reinstalled. It was probably a bad omen when I would get kernal panics when trying to install anything off the second disc of Mac Os X. So now, I'm still getting tons of kernal panics and programs shutting down.
    I have some additional ram, but software tests say it checks out. Could that still be a problem? What else could be wrong? This computer is underperforming like crazy and I don't like it one bit.

    Alex Tripp-
    Greetings.
    I won't bore you with the woulda, shoulda, coulda part about warranty repair. If it is still under warranty I would get it to the shop quickly.
    Did it start thrwing the panics about the time you added the memory? That itself would be a clue.
    Are you able to access the error logs? If so, anything good in them?
    Try running MemTest http://www.memtestosx.org/ It is more thorough than the Apple supplied utility.
    Luck-
    -DaddyPaycheck

  • Intermittent boot up problemsI have a G5 Dual 2GHz machine

    I have a G5 Dual 2GHz machine with 2Gb RAM. I have had an intermittent bootup problem every since installing Tiger.
    The machine appears to start as normal, gets as far as the spinning cog wheel then just shuts itself down as if there was a power cut.
    This happens every time I install an update and when I tryed to start up in verbose mode to try and work out why I can't see the message quick enough before it shuts down.
    It will however boot up in safe mode and sometimes this fixes it if I then start up normally.
    Other times I have to just leave it for about a half to one hour and it eventually boots up.
    This problem is now happening more frequently not just after updates and can take several attempts to get it to boot properly.
    If I run fsck in single user mode it reports that the file system is ok. If I run hard disk checks this also says everything is ok. I haven't as yet reinstalled a clean system.
    Does anybody have any ideas? Is this hardware or software? Any suggestions appreciated.

    Hi there,
    Thanks for all your tips which I have tryed but it doesn't seem to make much difference. In fact the machine wil l now on ly boot in safeboot mode.
    The Apple hardware test reported no faults. Disk utility verified that the hard disk was ok and I repaired permissions. I ran Tiger cacche leaner and said yes to all options. I also followed Al's suggestions and used font doctor to check out the fonts. It found three corrupted which I removed but this also did not make any difference.
    I looked in the system log and found the following :
    I don't know if they means anything to anybody:
    system.log:
    Description: System events log
    Size: 30.41 KB
    Last Modified: 31/08/2006 15:26
    Location: /var/log/system.log
    Recent Contents: ...
    Aug 31 15:25:44 localhost mDNSResponder-107 (Mar 20 2005 20: 31:47)[69]: starting
    Aug 31 15:25:45 localhost kernel[0]: MacRISC4CPU::start - found 'cy28508'
    Aug 31 15:25:44 localhost diskarbitrationd[54]: disk1s3 hfs 074EB148-4C56-3B7A-AEC6-A46DD1035113 Excelsior /
    Aug 31 15:25:45 localhost kernel[0]: Copyright (c) 1982, 1986, 1989, 1991, 1993
    Aug 31 15:25:45 localhost kernel[0]: The Regents of the University of California. All rights reserved.
    Aug 31 15:25:45 localhost kernel[0]: using 5242 buffer headers and 4096 cluster IO buffer headers
    Aug 31 15:25:45 localhost kernel[0]: DART enabled
    Aug 31 15:25:45 localhost kernel[0]: MacRISC4CPU: publishing BootCPU
    Aug 31 15:25:45 localhost kernel[0]: FireWire (OHCI) Apple ID 42 built-in now active, GUID 000a95ff feba07a2; max speed s800.
    Aug 31 15:25:45 localhost kernel[0]: ApplePMU::PMU FORCED SHUTDOWN, CAUSE = -122
    Aug 31 15:25:45 localhost kernel[0]: Extension "com.apple.driver.PioneerSuperDrive" has no kernel dependency.
    Aug 31 15:25:45 localhost kernel[0]: Security auditing service present
    Aug 31 15:25:45 localhost kernel[0]: BSM auditing present
    Aug 31 15:25:45 localhost kernel[0]: disabled
    Aug 31 15:25:45 localhost kernel[0]: rooting via boot-uuid from /chosen: 074EB148-4C56-3B7A-AEC6-A46DD1035113
    Aug 31 15:25:45 localhost kernel[0]: Waiting on <dict ID="0"><key>IOProviderClass</key><string ID="1">IOResources</string><key>IOResourceMatch</key><string ID="2">boot-uuid-media</string></dict>
    Aug 31 15:25:45 localhost kernel[0]: Got boot device = IOService:/MacRISC4PE/ht@0,f2000000/AppleMacRiscHT/pci@7/IOPCI2PCIBridge/k2-sat a-root@C/AppleK2SATARoot/k2-sata@0/AppleK2SATA/ATADeviceNub@0/IOATABlockStorageD river/IOATABlockStorageDevice/IOBlockStorageDriver/ST3160023AS Media/IOApplePartitionScheme/AppleHFS_Untitled2@3
    Aug 31 15:25:45 localhost kernel[0]: BSD root: disk1s3, major 14, minor 3
    Aug 31 15:25:45 localhost kernel[0]: jnl: replay_journal: from: 4745728 to: 5205504 (joffset 0x1af000)
    Aug 31 15:25:45 localhost kernel[0]: Jettisoning kernel linker.
    Aug 31 15:25:45 localhost kernel[0]: Resetting IOCatalogue.
    Aug 31 15:25:45 localhost kernel[0]: Matching service count = 0
    Aug 31 15:25:45 localhost kernel[0]: IOPlatformControl::registerDriver Control Driver AppleSlewClock did not supply target-value, using default
    Aug 31 15:25:45 localhost kernel[0]: IPv6 packet filtering initialized, default to accept, logging disabled
    Aug 31 15:25:45 localhost kernel[0]: UniNEnet: Ethernet address 00:0a:95:ba:07:a2
    Aug 31 15:25:46 localhost launchd: Server 2b13 in bootstrap 1103 uid 0: "/usr/sbin/lookupd"[60]: exited abnormally: Hangup
    Aug 31 15:25:46 localhost lookupd[92]: lookupd (version 365) starting - Thu Aug 31 15:25:46 2006
    Aug 31 15:25:46 localhost mDNSResponder: Couldn't read user-specified Computer Name; using default “Macintosh-000A95BA07A2” instead
    Aug 31 15:25:46 localhost xinetd[73]: xinetd Version 2.3.11 started with libwrap options compiled in.
    Aug 31 15:25:46 localhost xinetd[73]: Started working: 0 available services
    Aug 31 15:25:46 localhost diskarbitrationd[54]: disk1s5 hfs 734BBC31-E33A-3B7A-864E-41F8B7D857FF Work /Volumes/Work
    Aug 31 15:25:47 localhost diskarbitrationd[54]: disk1s7 hfs 31407C46-35BB-3104-855C-E77EDDFCC0F0 PSScratch /Volumes/PSScratch
    Aug 31 15:25:48 Macintosh kernel[0]: UniNEnet::monitorLinkStatus - Link is up at 100 Mbps - Full Duplex
    Aug 31 15:25:48 Macintosh configd[52]: setting hostname to "Macintosh.local"
    Aug 31 15:25:51 Macintosh mDNSResponder: Couldn't read user-specified Computer Name; using default “Macintosh-000A95BA07A2” instead
    Aug 31 15:25:52 Macintosh launchd: Server 2b17 in bootstrap 1103 uid 0: "/usr/sbin/lookupd"[92]: exited abnormally: Hangup
    Aug 31 15:25:52 Macintosh configd[52]: executing /System/Library/SystemConfiguration/Kicker.bundle/Contents/Resources/enable-net work
    Aug 31 15:25:52 Macintosh configd[52]: posting notification com.apple.system.config.network_change
    Aug 31 15:25:52 Macintosh configd[52]: setting hostname to "Vigor10"
    Aug 31 15:25:52 Macintosh lookupd[100]: lookupd (version 365) starting - Thu Aug 31 15:25:52 2006
    Aug 31 15:25:52 Macintosh kernel[0]: ATY,Simone_A: vram [a0000000:04000000]
    Aug 31 15:25:53 Macintosh kernel[0]: ATY,Simone_B: vram [a0000000:04000000]
    Aug 31 15:25:54 Macintosh configd[52]: target=enable-network: disabled
    Aug 31 15:25:54 Macintosh mDNSResponder: Couldn't read user-specified Computer Name; using default “Macintosh-000A95BA07A2” instead
    Aug 31 15:25:54 Macintosh mDNSResponder: Adding browse domain local.
    Aug 31 15:25:56 Macintosh /System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow: Login Window Application Started
    Aug 31 15:26:01 Macintosh loginwindow[151]: Login Window Started Security Agent
    Aug 31 15:26:14 Macintosh /System/Library/Frameworks/ApplicationServices.framework/Frameworks/ATS.framewo rk/Support/ATSServer: (-3230) Cannot use ATS Persistent Store - switching to old FODB cache code
    Aug 31 15:26:23 Macintosh KernelEventAgent[68]: tid 00000000 received unknown event (12)
    The bit about the Apple PMU forced shutdown may be significant.
    The only thing I can think to do is reinstall a clean system flolder unless anyone can suggest anything else.

  • Current uses for a G5 PowerPC dual 2GHz

    Hi guys.  I just undercovered an old silver G5, think it has 10.4 or 10.5 on it, with dual 2GHz PowerPC processors in it.  I know it's real old and can't really do much, but what would be some practical things I could use it for in a business environment.  Would it run a USB scanner?  Or what else can you think of?   Hate to just let it rust up sitting in storage.

    Hello,
    I use a G5 as my main computer at work still.
    If the Scanner doesn't have drivers for your OSX version there's always VueScan...
    http://www.hamrick.com/vuescan/vuescan.htm#supported
    TenFourFox is the most up to date browser for our PPCs, they even have G4 & G5 optimized versions...
    http://www.floodgap.com/software/tenfourfox/
    SeaMonkey seems pretty fast also, with many options...
    http://www.seamonkey-project.org/
    http://www.seamonkey-project.org/releases/

  • Dual 2Ghz PowerPC G5 Won't Go to Sleep

    I recently purchased a refurbished Dual 2Ghz PowerMac G5 from Apple which already came installed with Mac OS 10.4. The first thing I did when I booted it was to use the software updater to install the most recent versions of the operating system. Now when I select "sleep" from the Apple menu, the machine powers down and my Apple LCD monitor goes dark, but within seconds I can hear the fans start up then slow down and the machine wakes up. It does this every time I try to invoke the "sleep" command. Does anyone know how to resolve this problem so that the "sleep" command works again?

    Regarding USB devices, I have an Apple 20 inch cinema display (the new silver bevel model) which has support for both Firewire and USB ports. I detached the cinema displays USB plug from my G5 and lo and behold I can put the computer to sleep now. I was also experiencing system lock-ups before and all fans kicking in at high speed in which I could not wake up the computer and had to power the system down by holding the power button in. All these symptoms appear to have vanished after disconnecting the cinema displays USB plug from the computer. The Firewire plug to the cinema display appears to function normally. I wonder if the problem is in the display's power brick. The USB cable feeds into that brick before it reaches the ports on the display.
    Anyway, thanks for the tip on the USB devices. My system seems to be operating normally now.

  • Which is the highest Mac OS i can put on my G5 Dual 2Ghz?

    Which is the highest Mac OS i can put on my G5 Dual 2Ghz?

    OS 10.5.8 according to this site:
    http://www.everymac.com/systems/by_capability/maximum-macos-supported.html

  • Dual 2Ghz G5 Fans Ramp Up with Final Cut Pro 5

    Hey all,
    Somewhere amidst the release of OS X 10.4.3 and Final Cut Pro 5.0.4, our first generation Powermac Dual 2Ghz G5's fans will occasionally ramp up for 30-60 seconds, then die back down, several times a day. And when I say ramp up, I mean they go from as quiet as they can, to as loud as they can, and then slowly idle back down. On days I don't use Final Cut, the Powermac stays quiet. There's probably not a solution to this that Apple themselves won't have to fix with an update, but I was just curious if I'm the only one experiencing this. Thanks.

    Hi Fathertime,
    Thanks for your response. I'm rather late returning, but I wanted to follow-up on this. My Dual 2Ghz's fans didn't used to ramp up so obnoxiously like this, except when there was actually good reason to. As it is now, merely opening or playing back a simple DV video timeline causes the fans to ramp up to warp speed, and then slowly die back down multiple times throughout a workday. Needless to say, it makes audio tweaks and adjustments quite difficult when trying to listen closely and the computer keeps getting louder and louder...
    I'd wager that this issue arrived for me with a Software Update, although I have no idea which one. I'm currently running the most recent versions of everything Apple-related. Motion 2.0.1 is now endlessly crashing on me too, so maybe it's time to wipe this noisy monster clean.

  • G5 dual 2GHz wont see external 4Tb

    Can anyone confirm how to get G5 dual 2GHz to recognise an external larger than 2Tb. Was thinking of Sonnet range - Tempo SATA E2P card?
    Thanks

    Yes, it will recognise externals apart from anything over 2Tb capacity.
    Thanks

Maybe you are looking for