Generating signal as shown in the image in labview

Hello,
I am using labview 2011 and want to generate the second signal as shown in the attached image in labview as I want to use this as input for implementing the adaptive filtering, if the first signal in the image represents the output of the adaptive filtering.
Can I know how to generate second the signal.
Thanks.
Solved!
Go to Solution.
Attachments:
signal_generation.JPG ‏68 KB

The filtered signal looks like a sawtooth wave with some possible frequency variation. Hard to tell, because it is still quite noisy. Even the clean signal is not very clean, even though it looks better than the original, which has barely any discerning features.
PatanGova wrote:
Can I know how to generate the required type of clean signal and also the kind of noise to be added to it to make the required signal.
We cannot know the "requirements" by looking at the picture. What kind of instrument or data are you trying to simulate? You need to give us more background information.
LabVIEW Champion . Do more with less code and in less time .

Similar Messages

When a website asks me to enter the letter combination shown in the image below, no box letter or box appears. It appears in Internet Exployer and did in earlier version of FF. Am using FF 6.0. Help please

When a website asks me to enter the letter or number combination shown in the image below, no box letter or box appears. It appears in Internet Explorer and did in earlier version of FF. Am using FF 6.0. Help please

If images are missing then check that you aren't blocking images from some domains.
*You can inspect and manage all permissions on the about:permissions page, via the location bar.
*Check the permissions for the domain in the current tab in "Tools > Page Info > Permissions"
*Check that images are enabled: Tools > Options > Content: [X] Load images automatically
*Check the exceptions in "Tools > Options > Content: Load Images > Exceptions"
*Check the "Tools > Page Info > Media" tab for blocked images (scroll through all the images with the cursor Down key).
If an image in the list is grayed and there is a check-mark in the box "<i>Block Images from...</i>" then remove that mark to unblock the images from that domain.
Make sure that you do not block third-party images permissions.default.images
*http://kb.mozillazine.org/Images_or_animations_do_not_load
There are also extensions (Tools > Add-ons > Extensions) and security software (firewall, anti-virus) that can block images.
*https://support.mozilla.com/kb/Troubleshooting+extensions+and+themes

Can I get stepped out put voltage signal for controls from the BNC with Labview?

Hi!
I am new user to NI Labview. I am working in controls applied in Combustion sciences. I want control the Solenoid valve ( Jefferson made,230 V, 11 W) in stepped manner. BNC (2110) is used for the input signal (Piezoelectric pressure transducers) and output signal. The maximum out put voltage from BNC is 5 V. Can I get the out put voltage in stepped and increasing order to ensure the better controls of the solenoid valve?
Also I would like to know, is it possible for me to control the working frequency ( Injecting) of the solenoid valve with the help of Lab view?
Thanks.
With Regards,
Ganesh

Just having the same issue there, which is real not fun, I have not tried to contact them, but looking at your experience I am not sure if I should.
My key comes from the back of a laptop o so I guess that would be a W7
OEM, and that could explain why you can't download a ISO from their website, would that also your case ?
Also could it be because we are attempting to get the ISO after the product became EOL ?
http://windows.microsoft.com/en-us/windows/lifecycle
Maybe I will give a go with the customer care people and maybe I will get a right answer ;)
Will keep you posted

How to show the ellipse found in the IMAQ shape detect to the image

I have come out with the VI which had detected the ellipses. The ellipse result shown in the last part just only shows the number of matches and also the ellipses information. The problem is I wanted the ellipse found shown in the image to show where is the ellipse that detected in the LABVIEW but not only showing me the number of ellipse detected. Because I wanted to know the ellipse detected in the image provided that other shape is also in the image. Sorry for the bad English maybe I don't know use English to state my question correctly. Thank you for the helping I stuck in the last part to complete my task.
PS: I have attach my VI and image that I used in below. The minimum score set it to 990 and it will show the result of 3 numbers of matches. Anyone know how to locate the 3 ellipse in the image? Thank you for the help
Attachments:
oval 1.jpg ‏25 KB
testing.vi ‏51 KB

Uploaded the wrong vi in the previous.
This should have been the one uploaded.
Sorry.
Attachments:
testing_1.vi ‏58 KB

Need guidance for working with the available example labview VI

Hello,
I'm working with the pulse signals and the pulse signals will be effected by the motion artifacts.There is similar thread available on labview here Adaptive filtering to cancel out noise from an pulse signal for removing the motion artifacts from pulse signals.so,I am planning to use the vi posted in the thread as LMS block by block(example) with sampling rate of 100Hz and number of samples needed=100 using DAQPad-6015/6016.
But I am confused with the channels of DAQ as the author(who bulit this vi) says the channel0 for signal and channel1 for reference signal as shown in the attached image.
1)If channel1(aio) of DAQ is feeded with the analog input of pulse signals then what is the input needed/feeded to the channle1 of DAQ.
2)Can I directly use the vi by changing the sampling rate of 100hz and number of samples=100 or anything else is needed for this requirement.
Can someone explain me the required input to the channels and settings with the DAQ. thanks.
Attachments:
LMS_example.JPG ‏127 KB

Hello,
can someone explain how the DAQ channels settings are to be done.
thanks.

Acquire images with labview via firewire and TWAIN

Hi,
I have a camera from optronics. This camera is plugged to my computer
via a FireWire IEEE-1394 connection. The company optronics offers a
TWAIN driver for this camera: some files like TWAIN.dll and
TWAIN_32.dll. I would like to acquire images with labview and
communicate with the camera but I have no idea on how I should get
started.
The 3 main things I'd like to do are: 1) change the exposure time 2) snap images 3) see the images in labview.
I will really appreciate if someone could give me some ideas to get started...
Michael

AESulzer wrote:
Michael, From a
more general standpoint, what you'll need to do is use a Call
Library Function Node (located in the All Functions>>Advanced
palette) to call the necessary functions out of those DLLs. Before you
can do this, you'll need to know some specifics about what functions
are available in those DLLs and what parameters/outputs are associated
with them. This information is typically available in the product
manual or perhaps someone else with experience with your specific
device can speak to that. Once you know the functions necessary to
execute the desired operations, you simply configure a Call Library
Function Node for each of them and place them in your LabVIEW code.
Just
saw this and want to clarify on this. This is a total no-go! The Twain
interface is a very old technology from the days when Windows was a
cooperative multitasking environment without real tasks or threads. In
order for Twain to allow for some sort of multitasked integration into
an application it requires you to integrate the Twain handling into the
message loop of your application. As you do not have direct control
over the source code LabVIEW is written from, this is a very tedious
operation, with Windows message hooks and such, lots and lots of
semaphore protection to avoid race conditions etc. etc.
There is simply no way that you can do anything even remotely workable
just by using the Call Library Node. You will need a (rather complex)
external shared library that goes in between Twain and LabVIEW and
takes care of all the subtleties. I know for sure because I wrote such
a beast in the past.
Now there is a Toolkit from the French Alliance member Alliance Vision http://www.alliancevision.com/us/index.html that
does this. If you need Twain I would definitely go for this. My own
library is only to the point of what I had needed for a particular
project, (meaning it supports two specific scanners without issues) and
without any documentation for external users and I couldn't give it
away for free either.
Just want to warn you but there is a good chance that the Alliance
Vision Twain Toolkit does not really give you full programmatic control
of all the parameters of non-scanner devices and you won't be able to
avoid letting the Twain driver show the device specific configuration
dialog to manipulate specific settings.
In my own library I have low level functions to directly manipulate
Twain attributes but in order to be able to use that you would need a
through knowledge of the Twain specifications down to the API. That
together with the difficulties to support other devices I don't have
available, made us decide to not try to sell this Toolkit yet.
Rolf Kalbermatter
Rolf Kalbermatter
CIT Engineering Netherlands
a division of Test & Measurement Solutions

This is about iPhoto: I need to print the FULL IMAGE as shown on the screen: the image is SQUARE (equal on four sides). iPhoto keeps cropping it into a rectangle - THIS IS NOT ACCEPTABLE! How do I get what I see on the screen in print form???

I need to print the FULL image as shown on the screen - the image is SQUARE (equal on all four sides). iPhoto keeps cropping it into a rectangle - this is not acceptable! How do I get what I see on the screen into print form?

Like Terence explained:
OT

I use an external hard drive for my Lightroom library and I notice that all the images shown on there are DNG. On my MAC hard drive I have images shown as NEF. I desperately need to free up space on my hard drive, can I safely delete these NEFs?

I use an external hard drive for my Lightroom library and I notice that all the images shown on there are DNG. On my MAC hard drive I have images shown as NEF. I desperately need to free up space on my hard drive, can I safely delete these NEFs?

dj_paige wrote:
however, I do point out that obtaining an additional hard drive and not throwing anything away seems a preferable solution to me.
heidie22, dj_paige has a very good point there. I would not through away the NEF files; I would archive them to a external drive.
By the way, I am assuming that converting RAW files to DNG is a decision you have made and not an accident.

I want to use Get Panel Image in Labview 5.0.1 and need details on how to save the BMP data generated

I am trying to generate an application that saves a copy of its front panel on completion. This is easy to do using an invoke node with Print VI to HTML but this does not work in an .exe format. I have seen elsewhere that you have to use the Get Panel Image method, but no details are supplied in LV 5.0.1 documentation of how to use the "image" data (1-D Unsigned Byte array) that is generated. I want to save this in a format that can then be read as a bitmap in any standard graphics package. Any assistance?

Hi,
If you'd upgrade to LV5.1 or 6 you could use the 'standard' vi's for this.
You need a VI called "Write BMP File.vi". It's not shipped with LV5.0.1.
This vi only uses 3 subVI's, so perhaps someone at NI can convert it and
send it to you (sorry, I won't, it's copywrited).
If you cannot get this VI anywhere, you'll need to figure out the BMP file
format yourself. It's not too complicated, but still could take some days.
Perhaps someone figured it out before LV5.1 was released.
Regards,
Wiebe.
"RDK" wrote in message
news:[email protected]..
> I want to use Get Panel Image in Labview 5.0.1 and need details on how
> to save the BMP data generated
>
> I am trying to generate an application that saves a copy
of its front
> panel on completion. This is easy to do using an invoke node with
> Print VI to HTML but this does not work in an .exe format. I have seen
> elsewhere that you have to use the Get Panel Image method, but no
> details are supplied in LV 5.0.1 documentation of how to use the
> "image" data (1-D Unsigned Byte array) that is generated. I want to
> save this in a format that can then be read as a bitmap in any
> standard graphics package. Any assistance?

How to draw 2D shapes on the image generated by JMF MediaPlayer?

Hello all:
IS there any way that we can draw 2D shapes on the image generated by JMF
MediaPlayer?
I am currently working on a project which should draw 2D shapes(rectangle, circle etc) to
mark the interesting part of image generated by JMF MediaPlayer.
The software is supposed to work as follows:
1> first use will open a mpg file and use JMF MediaPlayer to play this video
2> if the user finds some interesting image on the video, he will pause the video
and draw a circle to mark the interesting part on that image.
I know how to draw a 2D shapes on JPanel, however, I have no idea how I can
draw them on the Mediaplayer Screen.
What technique I should learn to implement this software?
any comments are welcome.
thank you
-Daniel

If anyone can help?!
thank you
-Daniel

I have selected Print and a image is shown. When selected in library mode the image I want is shown, different image in print mode? How do I get the image in library mode to show and print?

When I select an image in library mode the image I want it is shown. When I go to print mode a different image is shown. Why doees this happen? How do I get my required image to show and print?
Thanks, Bob

You will likely get better program help in a program forum
The Cloud forum is not about using individual programs
The Cloud forum is about the Cloud as a delivery & install process
If you will start at the Forums Index https://forums.adobe.com/welcome
You will be able to select a forum for the specific Adobe product(s) you use
Click the "down arrow" symbol on the right (where it says All communities) to open the drop down list and scroll

NI Measurement Suit for Mobile/Fixed WiMAX 1.0 , is there any optiion to enable PUSC or AMC for the generated signal?

Hi.
I am using a NI VST to generate WiMAX signal. I have installed NI Measurement Suit for Mobile/Fixed WiMAX 1.0 on the compute. But I can't find any option on the front pannel of the generation suit to enable AMC or PUSC for generated signal. Does such feauture exist at all?
Thanks.
Solved!
Go to Solution.

Hello sam2013ni,
This is all that I am seeing for AMC and PUSC. Look in 'Zone Type'.
Best regards,
K. Anderson
Applications Engineer
National Instruments

Do images imported to Keynote retain their previous color profile? In other words, if the Keynote presentation will be shown using an sRGB profile projector, should the images be converted to sRGB prior to importing?

Do images imported to Keynote retain their previous color profile? In other words, if the Keynote presentation will be shown using an sRGB profile projector, should the images be converted to sRGB prior to importing or can they be batch adjusted in Keynote?

While I feel your comment doesn't directly address my question, why I am worrying is this.
This presentation is to a camera club. Color is important. Images shown in meetings are projected by an sRGB color profile projector. Most serious photographers us a color profile with a bigger space than sRGB (typically RGB1998). If you project an RGB1998 image on an sRGB projector the colors go to crap. More precisely they become dull and lifeless. Thus, I am trying to determine whether I need to convert the images I plan to put into my Keynote to sRGB and boost the saturation PRIOR to importing them or whether Keynote has a way to do this as part of the software.
Jerry

While generating PDF from webpage or website some of the images/texts doesnt show up in PDF. Also, there are a lot of formatting inconsistencies.

Creating, Editing & Exporting PDFs ! ! !

Can anyone please help, the websites hosted with us are developed on adobe CQ5.4 content management tool and when they are exported to PDF some of the images / texts doesn't get generated in the PDF. Also, the css /theme doesn't get generated resulting in formatting inconsistencies.
However, if the same website is generated using some online PDF converters all Images & texts are coming fine with correct formatting.
Is this issue due to using CQ CMS as that has a lot of components or is there a limitation with Acrobat XI pro trial version or anything else ?
Appreciate if some one could provide inputs.
Thanks
Anusha

Generating signal from the 5412 which is in sync with the external signal

Hi,
I am using the 5412 AWG. An external signal comes from the test unit. I need to generate a signal to the test unit which should be in synchronous with external signal which comes from the test unit. Can anyone help in this?
Regards,
Rajashekar

Hi Rajashekar,
You could synchronize these two signals by sharing a start trigger and using the input signal from your test unit as the sample clock for the 5412. There are some considerations when doing this that can be seen in the External Sample Clock Considerations section of the 5412 help linked below:
External Sample Clock Sources
If you are using LabVIEW, you can find examples in the Example Finder located at Help >> Find Examples. The FGEN examples are located at Hardware Input and Output >> Modular Instruments >> NI-FGEN >> Arbitrary Waveform Generation. You can choose which line to use as the sample clock. You will also need to add in some triggering. You can find an example of triggering at Hardware Input and Output >> Modular Instruments >> NI-FGEN >> Synchronization >>FGEN DAQmx Synchronization.vi. This is synchronizing to a DAQ card, but you can synchronize to your external signal just the same way, i.e., sharing a start trigger and a reference clock.
Regards,
Jim Schwartz

Generating signal as shown in the image in labview

Similar Messages

Maybe you are looking for