Help K8N Neo2 Platinum

hi Having Real Problems The With K8N Neo2 Platinum Board
When Starting Up The PC All I Get Is One LOud Beep That Lasts About
2 Seconds And Then Stops For 2 Seconds Then Does It Again And So On
But Never Gets To Post ,I Thought It Might Be Some Card Not Seated Right
But After Checking All Cards And Memory The Same Thing Happens Ive Now Took
All The Components Out And Rebuilt My Old 2600xp Socket a And All The Components Are Working Fine , So My Problem is HAve I Got A Doa Motherboard
Or Is It The Athlon64 3200+ ,Oh And The memory That I Been Using Is Branded
Samsung Pc3200 512mb And Ive Also Tried Samsung Branded Pc2700 2x256mb
But Since This Memory Works Fine In My old 2600xp System It Cant Be That Could it >?

One Of The problems That I Have Is I Didnt Get the D Card With The Motherboard
As i Bought A OEM Product ,Ive Only Just read About The Memory Config On MSI Site Which Clearly States That You Should Always Start To Populate The Green
First But I`m Sure This Has Only Just Been Added To The Site Check It Here
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=607
And yes The memory Can Work In Dual Channel Mode But Only With The Samsung PC2700 At 256mb A peice
My Thinking Behind The Graphics CArd Change ie (Swapping The Radeon 9800 Pro
For A Old Radeon 9600 Pro ) Is To See If It May be The Power Supply As The The 9800 Pro Shares The Same 12v line As The Athlon64 CPu But Can`t See It Being The Power Supply As its Only 3 Weeks Old And Is A enermax 470w With Dual 12v
RAils
But Still My Biggest Question Is Could This be A Faulty athlon64 3200xp Skt 939 CPU >?

Similar Messages

Please help (K8N Neo2 Platinum)

I have the afore mentioned mobo and I am not currently using any raid devices. The question is how can I disable that raid menu during booting ?
Thank you for your assistance.

Hi, welcome to the forum.
Do you actually get the RAID menu or just the option to press a key to setup a RAID configuration.
If it is the later that is normal behaviour and there is no way to make it go away. Just ignore it and go on.

Flash Bios is Write Protected? (K8N Neo2 Platinum)

Ok I just attempted to flash I have tried both winflash and boot disk.
Win flash tells me something about locks, however boot disk tells me that "Flash Bios is Write Protected". I have looked through the bios I can't for the life of me figure out 1) what version I am running or 2) where the write protect is at.
I have seen so many people that have had no problems with this I figure that it has to be something stupid I am doing wrong'
I did run this flash according to all the switches in the official "how to properly flash your bios correctly" thread.
Help
k8n neo2 platinum
amd 64 3800
1gig non-dual channel ram

http://www.msicomputer.com/support/sup_tshoot.asp#2_2
Let's start with identifying what bios version you have.

Need help with k8n neo2 platinum

I've just installed a new k8n neo2 platinum s939 board with a venice core 3200+ cpu the htt is 2000 and multiplier 10x.
I've gone to the core cell menu and set the htt to 4x (seemed to be this at default) and the max mem clock at 166 (more about this in a moment), the fsb will go quite easily up to 250mhz even 255mhz, but when I try 260 Mhz the machine when it reboots shows the initial slash screen but then goes to a blank screen with the cursor flashing in the top left hand corner, I can't even get back into the bios setup without clearing the cmos.
The odd thing is that the adjust cpu vid is showing a voltage of 1.50 and not 1.40 or startup.
Anyway with the fsb at 250mhz the bios screen is showing the Current ddr clock at 208 mhz ( not the max memclock setting of 166) the memory in the motherboard ( a crucial 512meg ddr333 single stick) seems to perform OK according to memtest which shows no errors after 2 cycles.
Any attempt to get to 260mhz fsb appears to fail even by upping the cpu vid to 1.525v unless i adjust the cpu voltage setting which by default is set to (by cpu vid) to +3.3%. Doing this enables me to get to fsb 260mhz but the memtest fails ( even when I set the max memclock to 133, which shows my current ddr speed at 174mhz, well below the 208mhz which appeared stable with the fsb at 250mhz?)
So firstly why are there two cpu voltage settings in the bios when my manual only shows 1 (there is no mention of this cpu vid setting?
How is it that my memory is stable at 208mhz with a fsb of 255mhz but unstable at 174mhz with the fsb set at 260mhz?
Why does the memory clock lock not appear to be working, the memory should be fixed at 166mhz but infact increases with fsb?
I have bios revision 1.5.
Please help as I am not familiar with the bios settings for this nforce 3 chipset, they seem rather odd to me. I'm sure my venice core 3200+ cpu can get beyond 250mhz fsb, I have another pc with a venice core 3000+ cpu which runs quite happily at 270mhz fsb.
PS I've tried reducing the htt to 3x but the same thing happens.

OK further feed back, I can get to over 260mhz fsb but the system is not stable the memory runs OK with mem test but I have problems with prime95.
I had to up the cpu core voltage to 1.53v to get to 260mhz using the cpu voltage setting in the bios and setting a 5% increase. increasing the cpu vid setting to 1.55v did not seem to do anything at all the core voltage was still at 1.43v.
I upped the mem voltage to 2.6v from 2.5 but still could not get the system to be stable, it may be that the memory is holding the system back but I don't want to pay for better memory at the moment. Unless anyone has got any other ideas it looks like I may be forced to settle with 250mhz, well still a 500mhz increase maybe not that bad. I've now to try 3d benchmarking using my radeon 9600xt and 3dmark 03.

MSI K8N Neo2 Platinum (HELP!)

Hi
Ive just bought a MSI K8N Neo2 Platinum motherbaord. When i try to power my pc up nothing happends. All i get is the green power led flashing on my tower. I dont get any fans spining or any other action.
omg whats wrong..... plz help !

Well we now know the motherboard... what about the rest of the components in the computer. When including specs on the powersupplies (post both the 400w and the 480w) include max amps for the 3.3v 5v and 12v rails. This info can be found on a sticker on the side of the PSU.
Do you have the D-Bracket installed? If so where is it hanging at?
Good Luck
Jeremy

MOVED: MSI K8N Neo2 Platinum (HELP!)

This topic has been moved to AMD64 nVidia Based board.
MSI K8N Neo2 Platinum (HELP!)

Well we now know the motherboard... what about the rest of the components in the computer. When including specs on the powersupplies (post both the 400w and the 480w) include max amps for the 3.3v 5v and 12v rails. This info can be found on a sticker on the side of the PSU.
Do you have the D-Bracket installed? If so where is it hanging at?
Good Luck
Jeremy

K8N Neo2 Platinum 54G BIOS problem

I recently bought a MSI K8N Neo2 Platinum-54G mainboard with W7025NMS v1.3 092204 revision of BIOS.
AMD Athlon64 3000+ 939 is installed on the mainboard, with 2x512 GEIL PC3200 memory modules in dual channel configuration working on default frequency of 200MHz. CPU is recognized correctly as AMD Athlon64 3000+ on startup.
Mainboard’s BIOS seems to be corrupted. In Cell Menu options, in the upper left part of the screen (printed blue) are processor and DDR working timings:
Current CPU Clock 1810MHZ, Current DDR Clock 200MHz.
Aggressive Timings and Dynamic Overclocking values are [Disabled] (processor working on its defaulf settings); Spread Spectrum is [Disabled] while all DRAM Configuration settings are set to [Auto].
While entering HT frequency settings, (locked to [x5]) there are no other values to select – empty, and there is no way to leave it (ESC doesn’t help, the only thing possible to do is to reset the computer by pressing the Reset button on the chassis), but the HT frequency settings were enabled when I loaded Fail-Safe settings, offering [1x], [1.5x], [2x], [2.5x], [3x], [4x], [5x].
Adjust CPU Ratio settings offer only [StartUp], [x4]~[x9] values, but as I understood by reading the manual there should be [StartUp], [x4]~[x20].
CPU Voltage, Memory Voltage and AGP Voltage are set to default.
CPU-Z, as well as SiSoft Sandra 2004 and SiSoft Sandra 2005 and MSI CORE CELL show that processor works at a core speed ~1005MHz, showing multiplier locked on x5.0 and HTT locked at ~200MHz, while the voltage is ~1.05V!
I downloaded the latest BIOS revision (v1.4), did the BIOS flash, but the problem remains!
Anybody, help!

Quote
HT frequency
is a known fault in bios & is easily sorted Bas HT Bios Error
Quote
CPU Ratio settings
AMD64 CPOU's have a lock on CPU ratios which varies according to the specification of the chip. therefore the multiplier available in your bios stops at the max multiplier allowed by amd for your cpu.
As an example i'm running a 3200 754 which has a maximum muliplier of 11 so that is the max i see in bios.
this guide may help Bios Guide

K8N NEO2 Platinum rebooting

Hi all,just got myself a 64bit MSI K8N NEO2 Platinum board & a 3200+,am happy with it but a couple of days ago i got a blue screen with a long message that i didnt have time to read before the pc rebooted,after the reboot i checked the event viewer log file in administrative tools/control panel but couldnt narrow it down as my particular error code wasnt among the possible causes.
Among some of the possible causes were incorrectly installed USB drivers or the BIOS,i downloaded the latest BIOS update before this problem started(V1.40) which i am using now,i used the MSI live update software to flash it which i did in windows mode.Sorry for prattling on!well it did it again tonight and i managed to read a bit of the writing on the blue screen which mentioned flashing the bios to the latest version.I was wondering if anyone else is having the same problem and if so could you please advise me? Thanks for your patience and any help Heres my sys specs:
Model: AMD Athlon(tm) 64 Processor 3200+
Speed: 2.01GHz
Model Number: 3200 (estimated)
Performance Rating: PR3015 (estimated)
Type: Standard
L2 On-board Cache: 512kB ECC Synchronous Write-Back (16-way, 64
byte line size)
Bus(es): ISA AGP PCI USB FireWire/1394
MP Support: 1 CPU(s)
MP APIC: No
System BIOS: Phoenix Technologies, LTD 6.00 PG
Mainboard: MS-7025
Total Memory: 1023MB DDR-SDRAM
Model: Micro-Star International Co Ltd (MSI) ???
(00E1)
Front Side Bus Speed: 1x 201MHz (201MHz data rate)
Model: Advanced Micro Devices (AMD) Athlon 64 /
Opteron HyperTransport Technology
Configuration
Front Side Bus Speed: 1x 201MHz (201MHz data rate)
Total Memory: 2048MB DDR-SDRAM
Memory Bus Speed: 2x 201MHz (402MHz data rate)
Monitor/Panel: CTX EX950F series
Adapter: RADEON X800 Series
Adapter: RADEON X800 Series Secondary
Removable Drive: Floppy disk drive
Hard Disk: Maxtor 6Y080L0
CD-ROM/DVD: HL-DT-ST DVDRAM GSA-4081B (CD 32X Rd, 24X Wr)
(DVD 4X Rd, 3X Wr)
CD-ROM/DVD: MSI CD-RW CR52 (CD 40X Rd, 52X Wr)
CD-ROM/DVD: AXV CD/DVD-ROM SCSI CdRom Device (CD 32X Rd)
(DVD 4X Rd)
1.44MB 3.5" (A:): N/A
Hard drive (C:): 76.3GB (51.9GB, 68% Free) (NTFS)
CD-ROM/DVD (D:): N/A
CD-ROM/DVD (E:): N/A
CD-ROM/DVD (F:): N/A
Serial/Parallel Port(s): 1 COM / 1 LPT
USB Controller/Hub: Standard OpenHCD USB Host Controller
USB Controller/Hub: Standard OpenHCD USB Host Controller
USB Controller/Hub: Standard Enhanced PCI to USB Host Controller
USB Controller/Hub: USB Root Hub
USB Controller/Hub: USB Root Hub
USB Controller/Hub: USB Root Hub
FireWire/1394 Controller/Hub: VIA OHCI Compliant IEEE 1394 Host Controller
Keyboard: Standard 101/102-Key or Microsoft Natural PS/
2 Keyboard
Mouse: PS/2 Compatible Mouse
Device: Creative SB Live! series
Device: Creative Game Port
Model: EPSON Stylus CX3200
Windows System: Microsoft Windows XP/2002 Home (Win32 x86)
5.01.2600 (Service Pack 2)
Network Drivers Enabled: Yes
Warning 100: Large memory sizes should be made of
Registered/Buffered memory.
Tip 101: Large memory sizes should be made of ECC/
Parity memory.
>
>
Device Type: VGA Video Adapter
Device ID: bus 1, device 0, function 0
Windows Device Name: RADEON X800 Series
OEM Device Name: ATI Technologies ??? (4A49)
OEM Hardware ID: FUN_0, VEN_1002, DEV_4A49, REV_00
Device Name: PC Partner Ltd ??? (4A49)
Product ID: VEN_174B, DEV_0D42
Revision: A / 1 (0)
Version: 3.00
Command Queue Length: 256
Fast-Writes Support: Yes
Over 4GB Addressing Support: No
Isochronous Mode Support: No
Addressing Support: 32-bit
Data Transfer Modes Support: 4x 8x

My K8N Neo Platinum [754] did not include a NB fan. But this usually means the overall size of the heatsink is larger. If you remove the fan from yours, the size of the heatsink will not be big enough to cool your NB. As for temps, I've never seen my NB get hotter than 45'C. Note that the core on my NB should be slightly different than yours.
You could try to use the BIOS fan control for the NB. If set correctly, it should reduce some noise.

K8N Neo2 Platinum Ordered - Advice for a noob please

Hi there,
this seems like a great forum, was hoping someone could give me some advice - Im trying to pre-empt any major probs....
I am a relative noob to building P.C's - done a few P4 based systems before but this will be my first Athlon based. This systems primary use will be gaming. I have the following on order (should be with me next week) : -
a) MSI K8N NEO2 Platinum Edition SCK 939 Motherboad
b) AMD ATHLON 64 3500+ 64bit SCK 939 Retail Inc Fan
c) 160GB Maxtor Calypso 8mb Cache 7200 SATA DHH
Components I have already
a) Graphics Card - Nvidia 6800 GT
b) Memory - Generic 2 X 512MB PC2700 DDR333 RAM
c) Sound Card - Creative SB Live Value
d) PSU - Jeantech 450W (22a on 12V Rail)
e) Case - pretty generic full tower case - no fans attached
f) CPU FAN - COOLERMASTER HYPER 48 SUPER SILENT HEATPIPE
g) Spare Hard drive - 120GB Maxtor IDE Hard drive
h) DVD Drives - 1 x Pioneeer 108 / 1 x Pioneer 104
I) Monitors - Ilyama 17" TFT & Toshiba 32WL36P LCD
I have some 'noobish' questions - apologies for my ignorance : -
1) Memory - Will my memory be okay ? Should I ditch it and buy some Corsair DDR400 (which everyone else seems to have!). Will performance suffer if I stick with the DDR 333 ? Do I need to adjust settings in BIOS regarding memory timing ? (I only picked up on this from reading through other posts on this board, and am totally clueless on 'timing'- Ive never needed to adjust timing on any previous PC's....!)
2) Sound Card - will I be better off sticking with the onboard sound on the MSI K8N neo 2 ? Or for best performance do I go with the SB LIve ? (god its a nightmare trying to get updated drivers for this card), Would I get a noticable performance increase buying an Audigy 2?
3) Vcore / other power issues - Reading this forum Im kinda scared by many posts along the lines of "..for stability I need to change my memory voltage to xx-V" or "...for a stable system I needed to change my Vcore to xx-V". Will I need to change the Bios default values on this system just to get it to run stably??
4) CPU FAN - Are AMD stock fans any good ? My Hyper 48 is quite highly rated....
5) Im completely new to SATA drives, but Ive printed off the very useful install guide on this site (which I intend to use). Is there anything I need to look out for concerning adding my IDE drive also.
I think thats about it just now - if anyone can see any other potential problems with my specs then please let me know. Im really not trying to be negative / pessimistic - after all the reason I have went for this motherboard is that it is rated as one of the best. Im just a bit paranoid that the dreaded B.S.O.D awaits me!
On a more positive note - does anyone have similar system specs they use for gaming ? How well does HL2 / Doom3 / Farcry etc fly J ? I cant wait !
Thanks for the time

you may find these helpful
Overclockers Uk Power Supplies
This Week Only Enermax Noisetaker 485W EG495AX-VE(G) SFMA ATX2.0 PSU (CA-007-EN) Might be tempting
Scan International Power Supply

SATA HDD installation on K8N Neo2 Platinum, Non-RAID, Non-Bootable

Hi-
I’m a rank newbie on this forum (first post). I have a K8N Neo2 Platinum Mobo, which I’ve recently gotten up and running, with Windows XP-Pro SP2 installed on a single IDE drive. I would now like to add 2 SATA drives. I don’t need or want the SATA drives to operate in a RAID array, nor do I want them to be bootable. I want to use them independently for data storage. I read the following thread (I am posting here on a separate thread per the author’s wishes not to get his original thread too junked-up) :
Single SATA or Multiple Drive Array Setup FAQ
I have not yet plugged-in either of my SATA drives, because I don’t want to risk corrupting my existing boot (IDE) drive. I just had a few questions about the procedure given in the referenced thread, in the Single Drive Setup:
- Step 14 States: “Make sure the “RAID Mode” is Stripping and Striping Block at 64k or Optimal. Hit F7 (Finish)”. Is this correct for a single non-boot drive?
- Step 22 States: “As most of you know when you enter the Setup for Win2k/WinXP you will need to hit F6 to load additional drivers for other SCSI devices.” I assume this means I need to boot from the Windows CD. Is this true even if I already have Windows installed on an IDE HDD on this system? At what point will I need to hit <F6> ? Will I be prompted to do so?
- I have downloaded (from the MSI website) the NVIDIA RAID CLASS DRIVER & NVIDIA Nforce Storage Controller (20 files, 1.3 MB total). Should I put these on a floppy? Or can I access them from a directory on my OS HDD?
- Should I go ahead and plug-in both of the 2 SATA drives I want to add to the system before beginning the driver installation? The only reason I would consider installing them one at a time is if it eliminated any confusion between RAID vs. independent (I want independent operation). If I do install them one at a time, do I have to install the driver twice?
Any help would be appreciated.
- the bbdude

OK Thanks JeanGuy and ssjkakaroto,
I have connected both of my SATA drives. They are enabled in BIOS but not set to RAID. I booted up to Windows on my IDE drive. In Disk Manager, the display shows Disk 0 (C: System), Disk 1 and Disk 2 as uninitialized, and my DVD (D:) drive. At this point, I could probably go ahead and run the Initialize and Convert Disk Wizard to get these disks formatted and be dome with ot now. Before I do that though, I just have a couple of more questions.
- I had already loaded the nVidia nForce3 system driver prior to installing the SATA drives, but I went ahead and did that again after installing the SATA drives and restarting Windows. I used Live Update, which went out to the MSI site and found version 5.03 of the nVidia nForce3 system driver. I'm not sure how to find the "Nvidia 5.10 driver package which include the latest SATA driver", ssjkakaroto referred-to. The Live Update install procedure did ask if I wanted to install IDE driver and I said yes. It then asked to over-write what I already had there (I said yes to that too). As the file names streamed-by, I though I saw some filenames with nv... listed. So, bottom line, is I'm not sure if I have the lates and greatest nVidia SATA drivers installed. How can I find out what drivers are installed?
- As I mentioned in my previous post, I have also downloaded and unzipped the NVIDIA RAID CLASS DRIVER & NVIDIA Nforce Storage Controller (20 files, 1.3 MB total) from the MSI site; however, I don't know how to "install" this now that I have the files. There are a couple of .exe and a .bat file (bit no setup.exe).
I may already have everything I need to partition and format these drives. I just want to bve sure I'm not skipping a step that is essential to optimal performance.
Thanks -
- bbdude

K8N Neo2 Platinum wont start up

After installing a new K8N Neo2 it worked perfectly for 1 day, no problems at all.
The day after nothing happened. When the psu is turned on it only gives a short flash on the leds, the fans turns for a second and then everything is of.
Have tried with only the most necessary connected to the psu, switched to only 1 RAM in different positions etc. Have cleared cmos every time.
D bracket leds are showing 4 reds for a short second and some times two greens diagonal upper left to lower right and the other two are red.
Any ideas???
Spec;
AMD Athlon64 3500+
K8N Neo2 Platinum
NX6800 Geforce 6800GT
WD Raptor 740GD 74G ( x2 )
Corsair CMX256A-3200LL ( x4 )
Antec True 480P ( 5V-38A, 12V-22A, 3,3V-30A )

Hi,
Its a common problem with this board... different theories are abound as to what causes it, an RMA might not help you
False Starts on MSI K8N Neo2 Platinum

System suddenly won't power on (MSI K8N NEO2 PLATINUM NFORCE3)

System specs are
COOLERMASTER TAC-T01 WAVE MASTER ALUMINUM ATX 4X5.25 1X3.5 4X3.5INT case
MSI K8N NEO2 PLATINUM NFORCE3 ULTRA S939 AGP 5PCI SATA 1394 SOUND 1000LAN
KINGSTON HYPERX 1024MB DUAL CHANNEL KIT PC3500 2X512MB DDR 433MHZ 184PIN
ATI Radeon X800XT PE AGP
SEAGATE BARRACUDA 7200.7 200GB SATA 8MB 7200RPM 8.5MS OEM
CREATIVE SOUND BLASTER AUDIGY 2 ZS 7.1 1394 PCI RETAIL BOX
LITEON 16X DVD-ROM INT E-IDE RETAIl
MITSUMI FA404A 7-IN-1 FLOPPY DRIVE & FLASH READER CF/SM/SD/MMC/MS
LG 4163b dvd burner
Nothing has ever been overclocked on this system.
Everything is plugged into a Belkin Surgemaster powerbar.
I haven't mentioned the power supply. I'll get to that. I have been using an ANTEC NEOPOWER 480W POWER SUPPLY (ATX12V DUAL 12V RAILS ACTIVE PFC W/ DETACHABLE OUTPUT CABLES) for about a year on this system without
any issues. One morning, I wake up, hit the power button on my coolermaster case, and nothing happens.
CPU fan won't even spin. Nothing happens.
O.k., blown power supply, I think . . . .
So I take out my Antec and put it in another system. That system turns on
without any problems.
Hmm . . .
I come here, and I read posts about
potential compatibility issues with Antec power supplies. But if it's a compatibility
issue why was my system working for about a year?
O.k., fine. I'll buy a Enermax 535W EG565P-VE FMA 24P (115/230 VAC) power supply.
I just plug it into the mainboard (nothing else). Hit the power button . . .
The CPU fan spins for half a second, and then nothing.
Did my motherboard just suddenly die for no reason?
Any suggestions?

Pull the AC plug from PSU and set cmos in clear position with battery removed for atlest 20 minutes perhaps longer .
Then try to post the system barebone .
Just cpu,1 pcs memory in slot 1 , gfx card , and keyboard in PS2.
No usb devices at all including card reader and no pci cards harddisks or cdoms/dvd/floppy.
It could also be caused by a short or a malfunctioning fan connected to mobo.
Try to disconnect all case fans from mobo headers if you have any connected to additional fan holders.
The chipset fan can also be disconnected momentarily just to see if it posts.
If none of this helps , replace cmos battery and try again .

USB Keyboard (K8N Neo2 platinum)

motherboard k8n neo2 platinum, somehow my motherboard does not recog my usb keyboard. i have gone to bios and enabled USB mouse/keyboard , my mouse is ok no matter which usb front or back but the keyboard usb does not work on any of usb . does anyone have any idea (hardly used keyboard, nearly new) all usb are ok??. your help will be much appreciated.
1-Motherboard MSI 7025 K8N Neo2 Platinum Chipset nForce3-250Gb/Ultra
2-CPU AMD Athlon Dual Core 3800X2
3- Graphic card (MSI FX5700) nVIDIA GeForce FX 5700
4-Memory 2 X1 GB DDR 400 DIMM kingston
5-HDD Maxtor 6Y160M0 (160 GB, 7200 RPM, SATA
6- OS Window XP Prof sp2
7-power supply Be Quite BQT- P5-420W

Bosskiller thanks for the reply it is a micorisoft multimedia, yes i have tried the back usb no luck there either. here is the link for the keyboard
http://www.farassoo.com/product/keyboard/fcr-8800.htm
but i wonder if you can tell me why some system their front usb doesn't work with usb keyboard a few have said this to me. many thanks

Reloading Windows XP on K8N Neo2 Platinum

Hello. I haven't been in this forum for quite a long time. I am refurbishing a computer I built in 2005, and need to reload Windows XP. This machine has a K8N Neo2 Platinum motherboard. Processor is an Athlon 64 4000+ (single core). My bootable hardrive is an IDE (PATA). I also have 2 SATA drives for data. None are connected in RAID. I have already updated my BIOS from V1.B to V1.D (current).
I am trying to remember the process I went through 3 yrs ago to get Windows XP. Here are a few questions:
1. Should I un-plug my 2 independent (non-bootable) SATA drives while I am doing the initial Windows XP install?
2. Do I need to hit F6 and load drivers? If so, I assume I should get the latest storage drivers, rather than using the floppy that came with the Mobo. Or, do I need to load anything with F6, ie will the windows XP install recognize my single IDE drive? If I need to load any drivers, are there separate drivers for RAID vs non-RAID ?
3. After getting Windows XP loaded, can I just run the MSI Live Update utility to get all of the remaining drivers updated? My BIOS is current (V1.D). Is there any reason I should go out to AMD or nVidia web sites to get drivers, or should MSI have all of the latest for this mobo?
Any help appreciated,
- bbdude

1. Yep its recommended, when installation is done add them.
2. No, do not load any drivers.
3. Use drivers from MSI Web: http://global.msi.com.tw/index.php?func=downloaddetail&type=driver&maincat_no=1&prod_no=587

K8N Neo2 Platinum troubles.

This will be my first post here, and I hate it to be a problem post. Anyway, I built my own computer about 2 months ago, and I seem to have a problem with 2D applications. Here is my setup before I show you what I mean.
Mobo MSI K8N Neo2 Platinum
CPU Athlon 64 3000+ S939
PSU Antec 350W
GPU PNY Geforce 6800GT 256MB AGP
200GB Maxtor SATA HD
Sony DVD-RW
1 GB Mushkin PC3200 DDR Ram
OS Windows XP Pro
Ok, here is my exact problem. I seem to have trouble playing most MPEG, AVI, and WMV video types. I say most, because some will work ok. I have a picture of my problem here:http://img.photobucket.com/albums/v281/ZeroX585/hmm.jpg
There seem to be lines that appear across my video, and some 2D games such as Doom, Zsnes, and Worms world party. They also seem to appear when certain colors are shown during playback of videos and games, (mostly the darks and blacks.) 3D games work FINE, (Half Life 2, Doom 3, Far Cry are perfect). No errors what so ever. I have also noticed that this happens also when the program is dependent on some DirectX resources. I have uninstalled and reinstalled DX9 about 3 times, I have my latest Graphics drivers, I have my latest Windows Updates, I have the latest Mobo chipset drivers and such as well. I have also installed Windows XP again. I am not certain that this is a complete motherboard issue, as I do not have parts to switch out, but I am lost as to what I can do next. I HAVE replaced the GPU with an older ATI Radeon 9000, and it still happens. I highly doubt that the problem would lie within the CPU, but it's probable. I have reseated all the parts in the computer, and checked over my motherboard to make sure there isn't any damage to it. I am lost as to what I can do next though.
There is one thing I have noticed though, is if I go into my Display Properties and take the Hardware Acceleration tab down to "Disable all Direct 3D and Direct Draw Accelerations", the 2D programs work FINE. But if it goes even one notch up, it goes back to the lines. Anyone know what this could be related to?? Thank you for your help.

Before I had my 6800 GT, I was using the Radeon 9000, and I did use Driver Cleaner 3 to remove the Radeon driver. I also used Driver Cleaner when I update the Nvidia drivers, and I've done this a few times as well. I've tried using the Nvidia direct drivers (Current version), and I am currently using the PNY version of the Nvidia drivers, all the while using Driver cleaner to remove the old drivers before installing the new ones. I have not tried any games or videos in safe mode though, I think I will do that. I will get a screen shot of Doom if I can. By the way, I am not certain what you mean by "Be sure to run the Nvidia option, not the Nforce option."

Help K8N Neo2 Platinum

Similar Messages

Maybe you are looking for