How to configure SNMP on SG300 using CLI

Hi,
Does anyone know how to configure SNMP on the Cisco SG300 switches? I have the SG300-10P. I am not fully familiar with the new command line interface on this device, it was easy on the IOS but finding it a nightmare on this one.
I put the following command in but it didnt work.
snmp-server view Interfaces interfaces included
snmp-server community ACB123 ro 10.x.x.x view default
I tried to follow the guidelines on the cisco website but thats all Web interface based, i can only access the switch remotely via CLI.
Thanks

Hi Rafik, here is a basic snmp v1/v2 configuration
snmp-server server
snmp-server community test1234 rw view DefaultSuper
This is basically wide open to anyone who knows the password. This should be enough to get you started then you can tweak additional options as you go. Give this a test, see if you can do what you're trying to do then modify this sample to work for your security needs.
-Tom
Please mark answered for helpful posts

Similar Messages

How to configure SNMP on all managed client using SCCM 2012 SP1

hi ,
do you know How to configure SNMP on all managed client using SCCM 2012 SP1?

As a side note, I made an interesting discovery last week: the SNMP Service is deprecated in Windows Server 2012. Why would you want to use SNMP on an actual Windows OS though? There are far better ways available to monitor Windows. I'm sure that lines
up with why they deprecated it.
Jason | http://blog.configmgrftw.com

How to configure snmp host in IPM?

Hi!!! I have CiscoWorks 2000 Rwan with IPM. I installed and configure IPM to send snmp traps when the treshold is excedeed. I can see on the graph that it is exceeded but I can not verify that it sending snmp traps.Where to view these traps and how to configure snmp reciver host?
Can I use CW2k syslog analyzer automated action to generate mail when get this trap?
THANKS FOR ANY HELP!!!!
Regards
Enes

Hi,
As you've discovered, IPM can help configure
these traps:
http://www.cisco.com/univercd/cc/td/doc/product/rtrmgmt/ipmcw2k/cipm25/ug/ipmfaq.htm#62205
But, you'll need to specify a dedicated NMS
server to receive these traps. The following
documentation should prove to be useful:
http://www.cisco.com/en/US/tech/tk648/tk362/technologies_tech_note09186a0080094aa5.shtml
http://www.cisco.com/en/US/tech/tk648/tk362/technologies_tech_note09186a0080094a05.shtml
You can use the appropriate "debug" command on
the router to confirm that traps are, in fact,
being sent.
The traps themselves are defined in the
CISCO-RTTMON-MIB.my and cannot interact
with the CW2000 syslog analyzer automated
action.
Thanks,
Roger

How to configure snmp on loopback interface, on vrf TEST, in ASR 9000 series

Hi there!
How to configure snmp v2, with community string, for ASR 9000 series, in interface loopback 1, that has vrf TEST
Regards!

oh that is somewhat vague, but let me try...
in order to enable snmp access to an interface in a vrf you need to enable MPP (management plane protection) in that vrf.
Something like this:
control-plane
management-plane
inband
interface Loopback100
allow all
if you have this and it doesn't work, a config snippet and some debugs (like debug snmp packet) will help to define what to do next.
regards
xander

How to configure snmp on solaris 10

hi, i am working on solaris management console(smc) .i want to configure snmp for this to send traps regarding my system performance and cpu usage ..can any body know ho to do this

I could use some help with this as well ... so far I have been unable to find a clear and concise document that can walk me through configurin gSNMP. Clean Solaris 10 installation, snmpdx is running - now how do I configure it? Better yet, how do I disable snmpdx and run net-snmp?
Please, someone help or at least paste a link to an article somewhere...

How to configure snmp on solaris 10 for sending traps to any EMconsole

i am working on solaris management console(smc) .i want to configure snmp for this (smc)to send traps regarding system performance and cpu usage ..can any body know ho to do this .i am new to solaris ..learned some basic administration of it ..

I could use some help with this as well ... so far I have been unable to find a clear and concise document that can walk me through configurin gSNMP. Clean Solaris 10 installation, snmpdx is running - now how do I configure it? Better yet, how do I disable snmpdx and run net-snmp?
Please, someone help or at least paste a link to an article somewhere...

How to configure SNMP agent for Oracle 10g

Hello,
I've installed oracle 10g in a Windows 2000 SP4 and I want to monitor database using SNMP.
I've already installed Windows SNMP agent but I haven't any idea how to configure Oracle in order to grant SNMP monitoring.
What should I do?
Is Oracle database ready to be monitored via SNMP by default?
Thanks in advance for your help.
Regards,
Carles

Hello,
Thanks for your message.
In fact, I already found this doc in oracle, but it just show executables I have to install and my question can I install these executables.
I've already installed Windows SNMP agent, configured and testedwith disk space checkings, but it doesn't work fine with Oracle.
I launched Oracle Universal Installer and I checked Installed Products, but I haven't found how to install SNMP agents for oracle.
How can I add Oracle Peer Master Agent and Encapsulator to my oracle installation?
Thanks again for your help.
Regards,
Carles

How to configure ADF application to use OAM Identity Assertion ? web.xml

We have a web application developed using ADF (application development framework) and deployed on WebCenter 11.1.1.2 (weblogic 10.3.2)
OID Authentication and OAM identity assertion is configured in WebLogic 10.3.2 .
How to configure security in ADF application (web.xml or weblogic.xml) so that it uses OAM identity assertion (already configured as authentication providers in weblogic server)
Any pointers or documentation so that application (developed using ADF) check for identity tocken and verifies it with one of identity assertion providers.

John,
I have to concur. With OAM you don't need this. OAM intercepts the calls and inserts a cookie for WLS to get user information from.
I strongly advise to go through the above mention OFM Security Guide. Esp. Chapter 10 tells you in every detail how to implement OAM SSO with WLS (with or without OHS as a proxy).
Reading this chapter saves you time and turnarounds on this topic...
--olaf

How to configure SNMP in solaris 10

i am working on solaris management console .i want to configure snmp for this to send traps regarding system performance and cpu usage ..can any body know ho to do this

Integration of Directory Server SNMP agent with Solaris Master agent is documented in the Administration Guide Chapter 14: Monitoring Directory Server using SNMP.
http://docs.sun.com/source/817-7613/snmp.html
Regards,
Ludovic.

How to configure SNMP on DMS or DMP?

for the first, English is not my mother tounge, so I may write a lot of mistake of my words.
One of my customer want to infomation of DMP that is down or up with SNMP tool.
I had download the tool named 'SNMP TESTER' and test with DMP, and DMS.
But the DMP has no SNMP configure set module or command. Only DMM has one sections of it's administrator - settings.
I changed the DMM setting like this
Queries
Query Operations : Enabled
Read Community : public
Notifications
Notification Operations : Enabled
Hostname or IP Address : 172.16.100.143
Port : 162
Trap Community : public
==========================================================
and my SNMP tester settings below.
Host name or address : 172.16.100.251
Community name : public
and these are logs of fail to test.
2012-11-07 17:27:04 - Starting SNMP test...
2012-11-07 17:27:04 - Connecting to
[email protected]
2012-11-07 17:27:05 - ERROR: Unable to complete the test.
2012-11-07 17:27:05 - ERROR: Data is incorrect (13)
2012-11-07 17:27:05 - [SNMP status] .1.3.6.1.2.1.1.1.0, .1.3.6.1.2.1.1.5.0, .1.3.6.1.2.1.4.1.0: No such name (#1)
==========================================================
My SNMP tester installed PC IP : 172.16.100.143
DMM : 172.16.100.251(Version 5.2)
DMP 4400 : 172.16.100.85 (UP status)
The SNMP service looks enabled. In fact, I'm not sure it's configure is right and working.
I'm not close to SNMP. So, I hope your experts will show me greatful kindness.
just two thing that the customer wants is simple.
OID number status 2 code and show them to within SNMP Tester. (UP & Down 2 status OID code needed)
How can I test the SNMP service is working and Showing the status of DMP within SNMP Tester?
P.S I attached the SNMP Tester program for your testing.

Hi Rafik, here is a basic snmp v1/v2 configuration
snmp-server server
snmp-server community test1234 rw view DefaultSuper
This is basically wide open to anyone who knows the password. This should be enough to get you started then you can tweak additional options as you go. Give this a test, see if you can do what you're trying to do then modify this sample to work for your security needs.
-Tom
Please mark answered for helpful posts

How to configure webcenter services to use external LDAP?

Reassociating the identity store with an external LDAP server is mandatory only if you're using the Documents service and/or the Discussions service, in which case the WC_Spaces server, Content Server, and Collaboration server must all be configured to use the same external LDAP server.
The question is how to configure?
Is there any document which details this?
Please help! this is urgent.
Regards

Refer
http://docs.oracle.com/cd/E28280_01/webcenter.1111/e12405/wcadm_security_id_store.htm#WCADM1845
http://docs.oracle.com/cd/E28280_01/webcenter.1111/e12405/wcadm_security_id_store.htm#WCADM345
Thanks

How to configure RAID 5 sys using SAS controller for APP CS4

Hi I would like to know how to configure my 3 HardDrives (600GB each) on RAID 5 connected to SAS controller to work smoothly with PremierePro CS4. Mainly to store scratch disk, and all preview files, etc.. At present it shows as one big hard drive in C:\ It shows as follows: OS(C 0.98 TB free of 1.08TB I would like to have at least one HDD out of 3 to store my scratch disk files and preview files... I have installed only CS4 Master Collection + Windows 7 64bit Ultimate as OS in this machine. Following is my system configuration: Intel Xeon E5620, 2.4GHz processor/12M Cache, 5.86GT/S, QPI, Turbo, HT, 4C Intel 5520 Chipset 12GB DDR3 RDIMM Memory,1333MHz, ECC Three 600GB (15000rpm) SAS HardDrives Perc6/i SAS/SATA Harware RAID card All SAS Drives, RAID 5, 3 drive configuration BlueRayBurner1GB PCIe X16 nVidia Quadro FX3800 ,Dual monitor DP+1 DVI Capable I am in a little bit strife on this. I am in a little bit strife on this and Open for any good and effective suggestions are much appreciated. Thanks Nathapushpa

You even have three more connectors free on your Perc controller, so you could add three more disks, without using any motherboard connectors.
I think you have two alternative approaches:
1. Add a smallish disk as a boot disk, i.e. a 150 GB Velociraptor and install OS and programs there and let your raid5 exist as it is, or
2. Add another 600 GB to your raid5 to make it a four disk array.
Of course you could also do both. Breaking the raid out to individual disks means that all data on the current raid will be lost, unless you have a backup available, but it will still mean a fresh install of OS & programs, so remember to deactivate Adobe before you do anything to your disk setup like in alternative 1 or breaking out the array.

How to configure CVC automation process using SNP master data and BI customer master data

Hi Gurus,
How to configure CVC automation in MPOS structure technically, using SNP master data in CVC creation such as Product and location details
and in parallel extract date from ECC to BI customer master data in DP. Where-in a APO BI cube should have only new combinations which are to be validated with ECC and existing combinations in the MPOS structure before creation of CVC in different regions of MPOS.
Second the automation should also check certain validations of product, location and are part of SNP-ECC master data and are these new combinations.
Could someone guide us in this process.
Thanks
Kumar

Praveen,
The short answer is to move the data into infoproviders or flat files for all of the 'characteristic-type' source data; and then copy CVCs from the infoproviders into the Planning area, probably using one or more Process Chains (program /SAPAPO/TS_PLOB_MAINTAIN).
The long answer is that this is not a trivial undertaking; this could end up being a pretty involved solution. If you do not have enough BW/DP expertise available locally to create this solution for you, then I recommend you consider engaging external resources to assist you. I personally wouldn't even consider starting to work on such a solution without first knowing a lot more about the detailed business requirements, and about any existing solutions that may already in place. An SCN forum is not really suitable for such an answer. In my opinion, the BBP doc alone would be 20+ pages, assuming no enhancements..
Best Regards,
DB49

How to configure MySQL to be used with J2EE 1.3.1 -- Very Very URGENT.

Hi All,
I have downloaded Sun's J2EE reference implementation 1.3.1. I want to use MySQL as my database instead of the default database Cloudscape that comes with J2EE SDK 1.3.1. Can any one help me configuring in doing the same.
Thanks and regards,
Venky.

Hi! I had the same problem, too. I�m Brazilian and I�ve been learning the English language yet, but I�ll try to describe how to configure J2EE with MySQL.
I am using MySQL version 4.1.7 with J2EE version 1.3 on Windows XP Professional. The driver version of MySQL is 3.0.16.
You have to configure the following two files:
- <J2EE_HOME>\bin\setenv.bat
- <J2EE_HOME>\config\resource.properties
Do the following steps:
1) Copy the JAR file of MySQL driver (mysql-connector-java-3.0.16-ga-bin.jar) to <J2EE_HOME>\lib directory.
2) In <J2EE_HOME>\bin directory open the setenv.bat file and analize the code. It is not hard to understand the code, it is just the classpath configuration of J2EE. After understand it, add a reference of MySQL driver (mysql-connector-java-3.0.16-ga-bin.jar), that was copied to <J2EE_HOME>\lib directory.
3) Run the <J2EE_HOME>\bin\j2eeadmin.bat to configure the resource.properties file.There are two command lines to be executed, as below:
- j2eeadmin.bat -addJdbcDriver <CLASS NAME OF THE DRIVER>
- j2eeadmin.bat -addJdbcDatasource <JNDI NAME> <URL>
For example:
- j2eeadmin.bat -addJdbcDriver "com.mysql.jdbc.Driver"
- j2eeadmin.bat -addJdbcDatasource "jdbc/mysql/test" "jdbc:mysql://localhost/test?user=username&password=pass"
4) After run j2eeadmin.bat, the resource.properties file will be modified. But when I did it and when I executed the verbose command to start J2EE, some error messages was exhibited. So I decided to open the resource.properties file and I noticed that the character "\" was added erroneously in a lot of places of the code. It did not seem correct, so I decided to remove these characters replacing them. Bingo!!! After I did it, I run verbose again and no more message error ocurred. I think it is a bug of J2EE.
Finish! I modified the datasource JNDI to access MySQL and then I run my EAR application. No problems occurred. My application is running succesfully.
Good luck!

How to configure JMagic(Java interface) using Image magic?

how to configure JMagic for linux OS? using Image magic API.?

It is unlikely many people here would have used it. Have you tried the [JMagic forums|http://sourceforge.net/mailarchive/forum.php?forum_name=jmagick-users] and the [JMagic Wiki|http://jmagick.wiki.sourceforge.net/Installing+JMagick]?
Edited by: mlk on 05-Sep-2008 13:44

How to configure SNMP on SG300 using CLI

Similar Messages

Maybe you are looking for