How to configure the router using Expand box?
I need help on configuring the Cisco routers.
Here's the scenario...
I want to compress as much all packets COMING IN to our network to optimize the bandwidth. When users from Lan accessing the internet, it goes out to our GW1 but I want the RETURN internet packets will go first to Expand 2 for compression then goes to Expand1 for decompression. Please see attached network diagram setup. All Expand appliances are already configured. Thanks.
What configuration should be in GW1 and R2, both C2851?
Hi Daniel,
I configure it as PBR so that all www traffic will be pass to that tunnel. I want all www traffic from Area 1 to Area 2 (vice versa) will pass to IPComp Tunnel (see diagram below). I configure a policy based routing in each router. Did I miss something in router configuration? Did I apply the PBR in right interfaces? How can I configure also the returned www traffic in Router 2? I really appreciate for any response. Thank you.
ROUTER 1
interface GigabitEthernet0/0
ip policy route-map EXPAND_AREA1
route-map EXPAND_AREA1 permit 10
description IPCOM TUNNEL TO AREA2
match ip address EXPAND_ACL
set ip next-hop A.A.A.2
ip access-list extended EXPAND_ACL
remark PACKETS THAT PASSES TO IPC TUNNEL
permit tcp any any eq www
========================================
ROUTER 2
interface GigabitEthernet0/0
ip policy route-map EXPAND_AREA2
route-map EXPAND_AREA2 permit 10
description IPCOM TUNNEL TO AREA1
match ip address EXPAND_ACL
set ip next-hop D.D.D.2
ip access-list extended EXPAND_ACL
remark PACKETS THAT PASSES TO IPC TUNNEL
permit tcp any any eq www
Similar Messages
-
How to configure the applet use Kerberos authentication
Hi all:
I know few about the java or applet security and hope someone can help me.
I have a MS IIS Web server named win2003stdbase1 and it use Kerberos authentication, and the
web server host a jar file.The client machine has jdk1.5 installed.When the client visit a html page which contains a java applet,the jre starts the applet and a dialog "Password Needed -Networking" popups.Then we input the right user name and the password,but the dialog popup again.The dialog display these message:
Server: win2003stdbase1/192.168.0.43
Scheme: ntlm
UserName:
Password:
Domain:
I suspect that the applet use the ntlm authentcation method which different from the web server,and I want it to use Kerberos authentication.How can I achieve this?
Any suggestion or idear will be appreciated.Thanks.Are there anyone can help on this? It is a urgent issue. Also if I did not explain it clearly, please let me know.Thanks.
-
I have ASA 5505 8.4. How to configure the switch to the backup channel to the primary with a delay (for example 5 min.) using the SLA monitor?
Or as something else to implement it?
My configuration for SLA monitor:
sla monitor 123
type echo protocol ipIcmpEcho IP_GATEWAY_MAIN interface outside_cifra
num-packets 3
timeout 3000
frequency 10
sla monitor schedule 123 life forever start-time now
track 1 rtr 123 reachabilityHey cadet alain,
thank you for your answer :-)
I have deleted all such attempts not working, so a packet-trace will be not very useful conent...
Here is the LogLine when i try to browse port 80 from outside (80.xxx.xxx.180:80) without VPN connection:
3
Nov 21 2011
18:29:56
77.xxx.xxx.99
59068
80.xxx.xxx.180
80
TCP access denied by ACL from 77.xxx.xxx.99/59068 to outside:80.xxx.xxx.180/80
The attached file is only the show running-config
Now i can with my AnyConnect Clients, too, but after connection is up, my vpnclients can't surf the web any longer because anyconnect serves as default route on 0.0.0.0 ... that's bad, too
Actually the AnyConnect and Nat/ACL Problem are my last two open Problems until i setup the second ASA on the right ;-)
Regards.
Chris -
How to configure the XI and PLM in discovery box
How to configure the XI (SLD, Integration repository, Integration Builder ) in SAP discovery system.
And also i want to configure the PLM and xRPM within R/3 of discovery box.
Regards,
Nilesh DamleHi Frank,
well, first of all, your application provides log configuration information using an XML file at deployment time. This file is called log-configuration.xml (you can see the DTD description here: http://help.sap.com/saphelp_nw04/helpdata/en/48/ef8748caed894bb4b3ae953a60c592/frameset.htm). There you can set configure log controllers, which could be two types: location and category. So, you can specify your location and severity there. This is described here: http://help.sap.com/saphelp_nw04/helpdata/en/35/671c0136b4714c9e1b16b68211287b/frameset.htm.
Then, after the application is deployed, the log configurations you provided for it are registered with the Log Configuration tool I mentioned about. Using this tool you can later on modify your configurations at runtime (for example, change the severity level) without having to redeploy the application.
I hope it's clearer now? I guess it was me not getting your first question correctly that caused your confusion.
Greetings,
Ivo -
How to get the workcentres used in the routing out of 2 alternate routings
Dear All,
I would like to know how to get the workcentres used in the routing out of 2 alternate routings.
I referred PLKO got the Task List Type (PLNTY), Group(PLNNR), Group Counter(PLNAL), Plant(werks).
I passed this in to PLPO, The problem in PLPO is we dont have the distinguishing field Group Counter(PLNAL), so I am getting all the ARBID including both alternates.
How to get the ARBID with respect to Groupcounter 1 alone.
If a get the ARBID , I can get the ARBPL from CRHD.HI,
Use PLAS Table also. you have to use PLKO> PLAS> PLPO.
Pass PLNNR & PLNAL in PLAS and get PLNNR & PLNKN.
Then pass these into PLPO.
work centers from CRHD
Regards,
Krishna Mohan
Edited by: Krishna Mohan N on Jan 31, 2008 12:28 PM -
How to configure the use of WS-RM in "PI 7.11 EHP1?
How to configure the use of WS-RM in "PI 7.11 EHP1?
Currently in the editing window of the communication channel (adapter type WS), I can not see any options regarding Reliable Messaging protocol (WS-RM).
The scenario that is required is as follows.
(Consumer WS-RM) -> (Provider WS-RM PI 7.11 EHP1) -> (ABAP Proxy Backend NW 7.0)
I would greatly appreciate any help,
Thanks,
Roger.
Edited by: Roger Solano on Apr 7, 2011 10:31 PMWS adapter supports WS Reliable Messaging. But WS adapter is used to communicate between two SAP web service runtime.
Check this blog and its links for understanding direct connection or point to point communcation using WS adapter
/people/william.li/blog/2008/02/13/point-to-point-connection-using-abap-in-sap-using-pi-71
Hoe that helps. -
airport extreme software will not install on vista, how can i still configure the router? Trying to help someone with vista get an airpot extreme configured. 10.0.1.1 does not work, the software will not install correctly on their vista machine. How can I get into the base tation and lock it down?
Hi - Vista can be tricky - I need more info to see if I can be of some help - first, is the Vista machine a desktop or a laptop and is it fully up to date with Windows Update (sp2 or higher)? - next, are you trying to install Airport Utility version 5.5.3 which is the correct one for Vista? - and finally, what do you mean "it will not install" - what kind of error messages or evidence are you getting?
-
How to configure the MOSS Crystalreportviewer using ActivX
Post Author: dileepj
CA Forum: General Feedback
Hi
I am using the MOSS BO integration Kit, and have used the crystalreportsviewer web part. But I want to configure the web part to use the ActiveX component. I would like to get some pointers as how to configure the web part to use the activeX viewer.
Thanks in advance
Dileep Josehow to access excel files using java.i know
jakaratapoi is support to access excel files
how?The home page for POI has all the how to's replied. :)
http://jakarta.apache.org/poi/hssf/how-to.html
http://jakarta.apache.org/poi/hssf/quick-guide.html -
How to set the router and play the Command & Conquer using direct IP mode?
My router is WRT54GFirmware Version: v3.03.1
How to set the router and play the Command & Conquer using direct IP mode with other computer?Hi, when you say direct IP mode, what do you mean ? do you wanna play the game online or on the LAN ??
can you give a few more details. -
How to configure Firefox to use OpenVPN?
summary: I'm running OpenVPN from a Debian client through a Debian jumpbox/server. After I [start the server, start the client] most IP-based applications (DNS, ping, ssh) seem to work from the client, but client's Firefox cannot connect to http://www.whatismyip.com/ (or any other URI). How to configure Firefox to use the VPN? or otherwise fix the problem? or further debug it?
details:
I have a laptop running debian_version==jessie/sid with Firefox version=33.0 which needs to access a compute cluster. The cluster formerly required only an SSL VPN (enabled by a Firefox plugin) to access, but now has several additional requirements, which I seek to satisfy by running the SSL VPN through a jumpbox running an OpenVPN server. The jumpbox is running a "vanilla" Debian 7.7.
I have been using the laptop successfully for a few years without network problems. Currently I have the laptop connected by wire directly to an ISP-supplied modem/router. With `openvpn` NOT running on the laptop, I see:
* `ifconfig` shows no entry='tun0' (just "the usual" entries for 'eth0', 'lo', 'wlan0'), and shows the expected client IP# bound to 'eth0'.
* I can `ping` my jumpbox/server using its real IP#, but cannot `ping 10.8.0.1`
* I can `ssh` to my jumpbox/server using its real IP#, but cannot `ssh 10.8.0.1`
* `nslookup www.whatismyip.com` gives correct results
* browsing to http://www.whatismyip.com/ shows my client's IP# (as also shown in `ifconfig`)
Both my client/laptop and server/jumpbox setups are quite generic OpenVPN-wise, and are almost exactly as described on the Debian wiki
https://wiki.debian.org/openvpn%20for%20server%20and%20client
me@jumpbox:~$ date ; cat /etc/openvpn/server.conf
Sat Nov 8 16:49:00 EST 2014
port 1194
proto udp
dev tun
ca /etc/openvpn/ca.crt
cert /etc/openvpn/server.crt
key /etc/openvpn/server.key
dh /etc/openvpn/dh1024.pem
server 10.8.0.0 255.255.255.0
ifconfig-pool-persist ipp.txt
push "redirect-gateway def1 bypass-dhcp"
push "dhcp-option DNS 8.8.8.8" # google public DNS
keepalive 10 120
comp-lzo
user nobody
group nogroup
persist-key
persist-tun
status openvpn-status.log
verb 3
me@laptop:~$ date ; cat /etc/openvpn/client1.conf
Sat Nov 8 16:51:31 EST 2014
client
dev tun
proto udp
remote ser.ver.IP.num 1194
resolv-retry infinite
nobind
user nobody
group nogroup
persist-key
persist-tun
mute-replay-warnings
ca /etc/openvpn/ca.crt
cert /etc/openvpn/client1.crt
key /etc/openvpn/client1.key
ns-cert-type server
comp-lzo
verb 3
up /etc/openvpn/update-resolv-conf
down /etc/openvpn/update-resolv-conf
My jumpbox/server firewall is currently set to forward everything, using `iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE`:
me@jumpbox:~$ date ; sudo iptables -L
Sat Nov 8 16:42:06 EST 2014
Chain INPUT (policy ACCEPT)
target prot opt source destination
fail2ban-ssh tcp -- anywhere anywhere multiport dports ssh
Chain FORWARD (policy ACCEPT)
target prot opt source destination
Chain OUTPUT (policy ACCEPT)
target prot opt source destination
Chain fail2ban-ssh (1 references)
target prot opt source destination
RETURN all -- anywhere anywhere
After I start `openvpn` on first the server and then the client, I see no OpenVPN errors on either the server or the client:
me@jumpbox:~$ sudo openvpn --script-security 2 --config /etc/openvpn/server.conf &
Sat Nov 8 17:48:25 2014 OpenVPN 2.2.1 x86_64-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [eurephia] [MH] [PF_INET6] [IPv6 payload 20110424-2 (2.2RC2)] built on Jun 18 2013
Sat Nov 8 17:48:25 2014 NOTE: the current --script-security setting may allow this configuration to call user-defined scripts
Sat Nov 8 17:48:25 2014 Diffie-Hellman initialized with 1024 bit key
Sat Nov 8 17:48:25 2014 TLS-Auth MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ]
Sat Nov 8 17:48:25 2014 Socket Buffers: R=[212992->131072] S=[212992->131072]
Sat Nov 8 17:48:25 2014 ROUTE default_gateway=ser.ver.gate.way
Sat Nov 8 17:48:25 2014 TUN/TAP device tun0 opened
Sat Nov 8 17:48:25 2014 TUN/TAP TX queue length set to 100
Sat Nov 8 17:48:25 2014 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0
Sat Nov 8 17:48:25 2014 /sbin/ifconfig tun0 10.8.0.1 pointopoint 10.8.0.2 mtu 1500
Sat Nov 8 17:48:25 2014 /sbin/route add -net 10.8.0.0 netmask 255.255.255.0 gw 10.8.0.2
Sat Nov 8 17:48:25 2014 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ]
Sat Nov 8 17:48:25 2014 GID set to nogroup
Sat Nov 8 17:48:25 2014 UID set to nobody
Sat Nov 8 17:48:25 2014 UDPv4 link local (bound): [undef]
Sat Nov 8 17:48:25 2014 UDPv4 link remote: [undef]
Sat Nov 8 17:48:25 2014 MULTI: multi_init called, r=256 v=256
Sat Nov 8 17:48:25 2014 IFCONFIG POOL: base=10.8.0.4 size=62, ipv6=0
Sat Nov 8 17:48:25 2014 ifconfig_pool_read(), in='TomRoche,10.8.0.4', TODO: IPv6
Sat Nov 8 17:48:25 2014 succeeded -> ifconfig_pool_set()
Sat Nov 8 17:48:25 2014 IFCONFIG POOL LIST
Sat Nov 8 17:48:25 2014 TomRoche,10.8.0.4
Sat Nov 8 17:48:25 2014 Initialization Sequence Completed
me@laptop:~$ sudo openvpn --script-security 2 --config /etc/openvpn/client1.conf &
Sat Nov 8 17:49:12 2014 NOTE: the current --script-security setting may allow this configuration to call user-defined scripts
Sat Nov 8 17:49:12 2014 Socket Buffers: R=[212992->131072] S=[212992->131072]
Sat Nov 8 17:49:12 2014 NOTE: UID/GID downgrade will be delayed because of --client, --pull, or --up-delay
Sat Nov 8 17:49:12 2014 UDPv4 link local: [undef]
Sat Nov 8 17:49:12 2014 UDPv4 link remote: [AF_INET]jump.box.IP.num:1194
Sat Nov 8 17:49:12 2014 TLS: Initial packet from [AF_INET]jump.box.IP.num:1194, sid=25df7af6 0ece4089
Sat Nov 8 17:49:13 2014 VERIFY OK: depth=1, <my config data/>
Sat Nov 8 17:49:13 2014 VERIFY OK: nsCertType=SERVER
Sat Nov 8 17:49:13 2014 VERIFY OK: depth=0, <my config data/>
Sat Nov 8 17:49:14 2014 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key
Sat Nov 8 17:49:14 2014 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Sat Nov 8 17:49:14 2014 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key
Sat Nov 8 17:49:14 2014 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Sat Nov 8 17:49:14 2014 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA
Sat Nov 8 17:49:14 2014 [TomRoche] Peer Connection Initiated with [AF_INET]jump.box.IP.num:1194
Sat Nov 8 17:49:16 2014 SENT CONTROL [TomRoche]: 'PUSH_REQUEST' (status=1)
Sat Nov 8 17:49:16 2014 PUSH: Received control message: 'PUSH_REPLY,redirect-gateway def1 bypass-dhcp,dhcp-option DNS 8.8.8.8,route 10.8.0.1,topology net30,ping 10,ping-restart 120,ifconfig 10.8.0.6 10.8.0.5'
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: timers and/or timeouts modified
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: --ifconfig/up options modified
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: route options modified
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: --ip-win32 and/or --dhcp-option options modified
Sat Nov 8 17:49:16 2014 ROUTE_GATEWAY lap.top.gate.way/255.255.255.0 IFACE=eth0 HWADDR=la:pt:op:MAC:ad:dr
Sat Nov 8 17:49:16 2014 TUN/TAP device tun0 opened
Sat Nov 8 17:49:16 2014 TUN/TAP TX queue length set to 100
Sat Nov 8 17:49:16 2014 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0
Sat Nov 8 17:49:16 2014 /sbin/ip link set dev tun0 up mtu 1500
Sat Nov 8 17:49:16 2014 /sbin/ip addr add dev tun0 local 10.8.0.6 peer 10.8.0.5
Sat Nov 8 17:49:16 2014 /etc/openvpn/update-resolv-conf tun0 1500 1542 10.8.0.6 10.8.0.5 init
dhcp-option DNS 8.8.8.8
Sat Nov 8 17:49:16 2014 /sbin/ip route add lap.top.IP.num/32 via lap.top.gate.way
Sat Nov 8 17:49:16 2014 /sbin/ip route add 0.0.0.0/1 via 10.8.0.5
Sat Nov 8 17:49:16 2014 /sbin/ip route add 128.0.0.0/1 via 10.8.0.5
Sat Nov 8 17:49:16 2014 /sbin/ip route add 10.8.0.1/32 via 10.8.0.5
Sat Nov 8 17:49:16 2014 GID set to nogroup
Sat Nov 8 17:49:16 2014 UID set to nobody
Sat Nov 8 17:49:16 2014 Initialization Sequence Completed
I then see the following on my client:
* `ifconfig` shows a new entry=`tun0`, which looks correct
* I can `ping` the server using either its real IP# or `10.8.0.1`
* I can `ssh` to the server using either its real IP# or `10.8.0.1`
* `nslookup www.whatismyip.com` gives correct results
... but I get no connection if I open a new instance of Firefox and browse to http://www.whatismyip.com/ :-( "Looking up www.whatismyip.com..." succeeds quickly but the status line continues to display "Connecting to www.whatismyip.com..." until the attempt times out. I also get the same behavior (connection timeout) if I open a new instance of Chrome, or if I browse to http://www.whatismyip.com/ with a Firefox opened prior to starting OpenVPN. FWIW I get the same behavior browsing to any URI, including (e.g.) Google.
This is a major problem for me! For the SSL VPN to work, I need to start a Firefox and run it (since the SSL VPN's vendor only supports it on Linux via a Firefox plugin) to access a particular remote-access website. Furthermore I need the SSL VPN to run through the jumpbox/OpenVPN. (Don't ask, it's a long, sad story ...)
Is there something I must do to configure Firefox to use the VPN? Or is there some other way to fix this?
Alternatively, what should I do to further debug the problem? It just seems odd to me that the other services work (e.g., `nslookup`, `ssh`) but Firefox does not. That being said, both Firefox and Chrome fail in this usecase, so the problem might be generic to web browsers.
your assistance is appreciated, Tom Roche <[email protected]>You're kidding. You have to go through that rigamarole just to put your bookmarks on your own server? Where's the simple FTP option?
Also, the above-linked article has a broken link. The link to the weaveserver (which is what you have to set up on your own server) is no good, and there is no obvious replacement. There are plenty of Weave-related repositories here:
http://hg.mozilla.org/labs
but it's not clear what you need. -
How to configure the .EAR to the OC4J server step by step ?
I have configured the JavaBean of the OC4J server with the following step:
1.create the eosp.ear with the JDeveloper's wizard
2.copy the eosp.ear to the OC4J Server with the Path:
J2EE_HOME/applications/
3.modify the server.xml and add the following words:
<application name="eosp" path="../applications/eosp.ear" auto-start="true"/>
4.restart the OC4J server and show the information:
Auto-deploying eosp (New server version detected)...
5.create the new JSP and this source code is:
<%@ page import="com.beautybeard.eosp.common.*"%>
<%@ page import="com.beautybeard.eosp.constant.*"%>
6.visit the JSP and show the error information:
Error parsing JSP page /eosp/usr_profile/login.jsp
Syntax error in source/eosp/usr_profile/login.jsp.java:5: Package com.beautybeard.eosp.common not found in import.import com.beautybeard.eosp.common.*; ^/eosp/usr_profile/login.jsp.java:6: Package com.beautybeard.eosp.constant not found in import.import com.beautybeard.eosp.constant.*; ^2 errors
why?
why can not find the package?
please help me outHi Sky-
It looks like you have a web application only.
You need to create a war file as described above. A war file is a jar'd file containing your web components, including your javabean class files, etc. JDeveloper 9i can do this for you. You've already done the hard work. Suppose that the project you have created that contains your javabeans, etc in JDev 9i is called myproject (with myproject.jpr as the project file). Right click on the myproject.jpr in the JDev navigator and select 'new...', go to Deployment Profiles and select J2EE Web Module (WAR File) - a general screen will pop up asking you to save the deployment profile (you can just use the default if you want). Once you select OK on that, you will get a screen that calls itself the J2EE Web Module Deployment Profile Settings. This is the screen that you can use to enter your information.
Your servlet and javabean classes will go into WEB-INF/classes subdirectory that you see to your left in this window. Simply select the WEB-INF/classes entry and it will display a list of your java sources (it will only place the compiled output in this directory - there is a toggle for it).
Once you have specified that your javabean and servlet classes go in this directory, you should be set. Go ahead and save / close. In your navigation screen under your project (myproject.jpr or whatever your project name is) you will see your files, jsps, etc and something called webapp1.deploy (if you accepted the default). If you right-click on that, you will get a menu that asks a number of things, one of which is to Deploy to EAR file. Select that entry and it will create an ear file for you. You can play with the various settings to change the name of the ear file, but that's about all you have to do. Once this is completed, you can put the EAR file on your linux box or wherever you want, adjust your server.xml and default-web-app.xml files and launch the app!
Good luck!
Ray
Hi,Ray
Thank you for giving me the detail information!
I'm sorry that I can not give the detail and clear problem ,which make you delusoried.
ok,now I give you my aim.
1. I will construct my application system with JavaBean(not EJB),Servlet,JSPs (linux+IAS+JDeveloper+Oracle8i database)
2. I will package business function with JavaBean. example:
* CheckLogin.java
package com.beautybeard.eosp.javabean.usrprofile;
import com.beautybeard.eosp.common.*;
import com.beautybeard.eosp.data.*;
import java.io.*;
import java.lang.*;
public class CheckLogin{
public CheckLogin()
//do nothing here
public boolean getCheckLogin(){
3. I will control the request and response with Servlets.
example:
*CheckLoginSevlet.java
package com.beautybeard.eosp.servlet.usrprofile;
import javax.servlet.*;
import javax.servlet.http.*;
import java.io.*;
import java.util.*;
import java.sql.*;
import com.beautybeard.eosp.servlet.*;
import com.beautybeard.eosp.javabean.usrprofile.*;
public class CheckLoginServlet extends DefaultServlet
public void service(HttpServletRequest req,HttpServletResponse res) throws IOException, ServletException
//use the JavaBean
CheckLogin cl = new CheckLogin();
if (cl.getCheckLogin){
res.sendRedirect("login.jsp");
}else{
res.sendRedirect("err.jsp");
4. I will display the result with JSPs:
example:
<%//login.jsp%>
<%@ page import="com.beautybeard.eosp.common.*"%>
<%@ page import="com.beautybeard.eosp.data.*"%>
5. I have success on running the above steps in the 9iJDevelper(pure java) environment(OS:Windows 2000 Server), and now I will move the JSPs ,Servlets,JavaBeans to the Server(linux) without the JDeveloper's deployment wizard.
how to configure the IAS to carry my point?
thank you!
Sky liu -
How to count the number of text boxes that are data entered
How to count the number of text boxes that are data entered in visual basic form.
Here is an Iterator that expands on my previous response:
''' <summary>
''' Iterator for form controls
''' </summary>
''' <param name="onlyControlsOfType">specify type if a certain type of controls needed</param>
''' <param name="onlyTopLevel">if true don't search containers within the form</param>
''' <returns></returns>
''' <remarks></remarks>
Private Iterator Function AllControls(Optional onlyControlsOfType As Type = Nothing, _
Optional onlyTopLevel As Boolean = False) As IEnumerable(Of Control)
Dim ctrl As Control = Me.GetNextControl(Me, True)
Do Until ctrl Is Nothing
If onlyControlsOfType Is Nothing OrElse ctrl.GetType = onlyControlsOfType Then
If TypeOf ctrl.Parent Is Form OrElse Not onlyTopLevel Then
Yield ctrl
End If
End If
ctrl = Me.GetNextControl(ctrl, True)
Loop
End Function
Some sample uses:
For Each
For Each c As Control In AllControls()
Debug.WriteLine(c.Name)
Next
List of all controls, including controls in containers i.e. Groupbox
Dim l As List(Of Control) = AllControls().ToList
List of all Textbox controls, including Textboxes in containers i.e. Groupbox
l = AllControls(GetType(TextBox)).ToList
List of all Textbox controls, don't include Textboxes in containers i.e. Groupbox
l = AllControls(GetType(TextBox), True).ToList
'Those who use Application.DoEvents() have no idea what it does and those who know what it does never use it.' JohnWein
Multics
My Serial Port Answer -
I have a Cisco/Linksys WRT-54G wireless router and 2 Airport Extremes (the small ones that plug directly into the wall). Is it possible to extend the network from the router using these two AEs? I have a DVD player and Ext HD plugged into the router too. Any ideas? I'm guessing the only way is to do what I've seen in these community pages which states that it can be done but it will drop the bandwidth by 50%. Thoughts?? Thanks!
The Cisco/Linksys WRT-54G was one of the very few routers said to be compatible with Apple's implementation of WDS (Wireless Distribution System) settings.
The info that I have on file indicates that only the WRT-54G versions 4 and under were compatible, so that would be one bridge to cross.
Even if you find that your Cisco/Linksys might be the right version, Apple never published instructions on how to configure the Express devices with other manufactures, so users were left to their own devices to try to figure out how to get things working. Apple's instructions to connect to other Apple devices are in the link below:
WDS network
If you were hoping to use 2 Express devices in this type of configuration...even if it works...the bandwidth penalties will be extremely severe.
The first Express drops the bandwidth (and speed) on the entire network in half and the second halves everything again. So, the result, in effect would be a "g" wireless network running at 25% speed. Few users would consider installing this type of network.
At this point, it becomes one of those things where the fact that you might be able to do something does not mean that there would be much value in doing so. But, it is your decision to decide if you want to try to proceed. -
How to configure sendmail to use multiple LDAP servers ?
Hi everybody!
I have a sendmail running on Solaris 10 and a LDAP server(192.168.1.9) also running Solaris 10 OS. I have configured the sendmail the following way:
bash-3.00# ldapclient list
NS_LDAP_FILE_VERSION= 2.0
NS_LDAP_BINDDN= cn=proxyagent,ou=profile,dc=email,dc=reso,dc=ru
NS_LDAP_BINDPASSWD= {NS1}*********************
NS_LDAP_SERVERS= 192.168.1.9
NS_LDAP_SEARCH_BASEDN= dc=email,dc=domain,dc=ru
NS_LDAP_AUTH= simple
NS_LDAP_SEARCH_REF= FALSE
NS_LDAP_SEARCH_SCOPE= sub
NS_LDAP_SEARCH_TIME= 30
NS_LDAP_CACHETTL= 43200
NS_LDAP_PROFILE= default
NS_LDAP_CREDENTIAL_LEVEL= proxy
NS_LDAP_BIND_TIME= 10
I also have another LDAP server (IP 192.168.1.10). It is configured as a replicant of the 192.168.1.9 LDAP server.
The question is how can i configure sendmail to use both LDAP servers ?
The man pages explain how to configure ldapclient to use ONE server and what if want to use two or more? All the settings and the profiles the same.
Thanks in advance =))Hi!
To add LDAP servers to the Solaris ldapclient, you might use the ldapclient command:
ldapclient manual -v -a defaultServerList="servera.yourdomain.com serverb.yourdomain.com"
But this is only failover, AFAIK the Solaris ldapclient does not perform loadbalancing by itself.
But I am not sure about your sendmail programm. Normally, sendmail has its own configuration
and can be configured to use LDAP e.g. for aliases etc.
Regards!
Rainer -
How to hold the value in List box.
Hi All,
On my screen painter Screen I am displaying the Sold to party and ship to party with thier address.
I am also displaying the Shipping condition based on ship to party. To display the shipping condition i am using list box. Once the user enter the sold to party automatically all the field is going to populate in their respective fields. I am facing the problem that, The list box getting populated with shipping condition but once you choose the shipping condition and hit the enter the list box getting refreshed. I am using this code in PAI event. And I can Only use this in PAI.
The Function i am using for list box is CALL FUNCTION 'VRM_SET_VALUES'.
Pls suggest me how to hold the value in List box.
Thanks,
RakeshHi,
Now i am using in PBO.
the code below in in PBO.It is still not holding the value.
if list[] is initial.
perform SHP_COND.
endif.
form SHP_COND .
*DATA: SHOP(80).
clear : GT_VSBED, list.
refresh : GT_VSBED, list.
select vsbed
from knvv AS K
into table GT_VSBED
where Kvkorg = vbak-vkorg "Kkunnr = GV_STPH
and K~vtweg = vbak-vtweg
and K~spart = vbak-spart.
select VSBED vtext
from TVSBT
into table list
for all entries in GT_VSBED
where spras = sy-langu
and vsbed = GT_VSBED-VSBED.
*break-point.
NAME = 'SHP_CON'.
CALL FUNCTION 'VRM_SET_VALUES'
EXPORTING
id = NAME
values = LIST[]
EXCEPTIONS
ID_ILLEGAL_NAME = 1
OTHERS = 2
IF sy-subrc <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
endform. " SHP_COND
Thanks,
Rakesh
Maybe you are looking for
-
Mystery: Thinkpad's bluetooth range suddenly reduced
Tl;dr: My Thinkpad's Bluetooth broadcast range suddenly dropped to a mere few feet. Afaik it's not about the headset, not about the drivers and not about the antennas. Hello, I was hoping somebody could help me with a problem that has left me complet
-
MacBook No Fire Wire? Getting Sony MiniDV Into Mac
I am new to Mac, this is our first Mac and I am loving it. I have a Sony MniDV camcorder. I want to import the video into my Mac. My camera requires a firewire connection, but the macBook doesnt have one. Am I out of luck or is there a way to make th
-
How to model a non key figure numeric field
I am new to SAP BI, so please acceopt my apologies if I am asking a very basic question. I have some numeric fields which are attributes of master data. These fields are not key figures and will not be aggregated. How can I model this in BI? I have t
-
Setting Line Pattern for Lines
Hi All, How to set line pattern for Lines? I am trying to use Line Pattern to draw some thing like "======" ( with out gap though I used equal symbol to draw I don't have other way to show an example). I have tried setting line pattern it is not work
-
After Effects crash on startup
Well, on my Windows 7, 64-bit computer After Effects CS5 crashes on startup. There's no error message, but in Windows 7 event viewer I get this: Faulting application name: AfterFX.exe, version: 10.0.1.19, time stamp: 0x4c785da6 Faulting module name: