HP C4780 Wireless Install Issues

Hi, Ive recently gotten a PhotoSmart C4780 but am having problems with connecting it via wireless. i am unable to use the USB connection as the port on the rear is damaged, this install has been going on for days and i'm slowly starting to think it'll be something simple that i've missed.
I'm using a Virgin Media Super Hub manufactured by NetGear. this router is running WPA with a physical pushbutton, however when attempting to connect using push button the printer keeps throwing up WPS ERROR.
I've printed several Network configuration pages, ranging from offline to ready. i've done the same with the wireless network test page. these have ranged from FAIL FAIL FAIL to all PASS. My printer has shown a signal strength indicator of full on the control panel. But after restart has lost all settings again.
I'm thinking that my main problem is when it is aquiring an IP address. On the Network Config Page its IP address is coming up as 169.254.92.103 Everything else on my wireless network is using an IP starting 192 so im assuming its not connecting. I have tried entering the printers ip into a browser window but nothing happens.
Has anybody got any ideas that i can try??
Regards
Carl

Hello-
From what i see , your router is broadcasting in dual or "mixed" mode (802.11g and 802.11n) Is there anyway for you to change it to 802.11g mode only ?? HP printers prefer this frequency. After you make the changes try to connect the printer to your network. You are correct about the IP address. You need to be the same (at least the first three numbers 192.168.*.*) as your computer.
The 169.*.*.* numbers is a generic windows default number.
The easiest method is USB to Wireless. But since your port is bad, you will have to make WPS work:
To connect the HP Photosmart using WiFi Protected Setup (WPS)
1.
Do one of the following:
Use Push Button (PBC) method
a
. Set up wireless connection.
❑
On the Home Screen, press button next to Scan.
❑
Press button next to Wireless Menu.
❑
Press button next to WPS.
❑
Press button next to Push Button.
❑
Press corresponding button on WPS-enabled router or other networking
device.
❑
Press OK.
b
. Install software.
NOTE:
The product begins a timer for approximately two minutes in which the
corresponding button on the networking device needs to be pressed.
I hope this helps.
Also, remember a click on the Kudos star to the left is a quick "Thanks" for a helpful post.
Please select the "Accept as Solution" button on the post that best answers your question.
I appreciate your input !
Thank You,
Donald

Similar Messages

  • Photosmart c4680 wireless install issues

    Recently purchased a hp pavilion g6 laptop and installed my photosmart c4680 printer as a wired printer, but now i am wanting to set it up as a wireless printer but i can't seem to completely uninstall the printer to go through the complete installation process again to set up the printer wirelessly this time. I have a router and have it installed and set up, but i just can't get this darn printer to set up wirelessly. I have tried to install and reinstall several times but i never get back to the initial install like i did when i first had set it up with the step by step on screen instructions instead it does like a plug and play set up; and i am ready to just pick the thing up and smash it on the floor. Please help !!!

    Hi dilyb,
    The HP Photosmart C4600 All-In-One Printer is USB only.
    http://h10025.www1.hp.com/ewfrf/wc/document?docnam​e=c01666390
    I am an HP employee.
    Say Thanks by clicking the Kudos Star in the post that helped you.
    Please mark the post that solves your problem as "Accepted Solution"

  • Ive recently moved to Muscat in Oman and had wireless installed in my apartment.  I can connect to my laptop but my Ipad will not connect.  Any suggestions

    Trying to connect to my Ipad.  I've used it in coffee shops in Muscat and the hotel without any problem.  I've now had wireless installed in the apartment.  I can connect to my laptop but I cannot get the Ipad connected to the wireless - I've tried everything.  Any suggestions would be gratefully appreciated.  I've also tried Omantel who installed the wireless without any help.

    Usually I suggest checking that your WiFi router firmware is up to date, but your router was just installed.  Still, it might be worth checking with the manufacturer's web site.
    Here are Apple's support articles:
    iPad:  Troubleshooting WiFi networks and connections:  http://support.apple.com/kb/TS3237
    iPad:  Issues connecting to WiFi networks:  http://support.apple.com/kb/TS3304

  • LaserJet Pro CP1025nw - Software Installation Stalls During a Wireless Install

    In case anyone runs into an issue with the install freezing during a wireless install, HP has provided information on getting the unit installed properly in the following doc.
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02607413&cc=us&dlc=en&lc=en&jumpid=reg_R1002_US...
    Though I work for HP, My posts express MY opinion, and not those of HP.

    Hello
    I see that yous are having issue setting up the cp1025nw on the 10.8.
    You can configure the printer on the wireless network through ethernet cable without any software.
    Restore the printer back to factory settings if not already setup on the network from another computer.
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02471640&cc=us&dlc=en&lc=en&jumpid=reg_r1002_us...
    Connect the network cable to the product and to the router. (temporary)
    Wait about 1 minute and then print a configuration page.
    (select operating system then select Method one.)
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02495036&cc=us&dlc=en&lc=en&jumpid=reg_r1002_us...
    Use the ip address from the configuration page and type it in the address bar of browser (internet explorer, safarari)
    This will open the embedded web server for the printer.
    Select the networking tab, select wireless on the left side, set it to infrastructure and put in encrytian
    (network passwords) apply then remove the ethernet cable from the printer.
    Should have a solid blue light in about 1 minute.
    Then on the mac just add the printer with the airprint driver.
    Click on the Apple, click System & Preferences, and then click the Print & Scan icon,click add a printer, then select the printer from the list, make sure the name listed beside use: shows airprint, select add.
    Test the printer on the wireless now.
    Let me know how this turns out.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • Iphone/IOS 6 and Enterprise Wireless Networks Issue

    Hi there,
    Our company runs Cisco wireless using WPA2 Enterprise and AD Authentication. Now we currently have multiple vendor phones/laptops working fine including Apple Macbook Pro's, Apple Iphone 4s, Samsung Galaxy S2/S3 working on the wireless without issue.
    However Ive been seeing issues with Iphone 5s and an Ipad now as well running IOS 6 where it just wont connect to the network. I am using Iphone configuration utility to install a Wireless profile with the certificate/AD credentials onto the Apple device.
    I just loaded the profile on an Iphone 5 and it worked straight away.
    However on ipad and other iphone 5's this is what happened, it associated to the Wireless but never got an IP address so never finishes connecting. just sits on spinning wheel.
    Here is some output from the Iphone configuration utility console:
    Nov 13 14:45:47 Sam-iPad eapolclient[2548] <Notice>: eapmschapv2_success_request: successfully authenticated
    Nov 13 14:45:48 Sam-iPad kernel[0] <Debug>: 285568.132121 wlan.N[12106] AppleBCMWLANCore::setCIPHER_KEY():  [eapolclient]: type = CIPHER_MSK, index = 0, flags = 0x0, key lenght 64, key rsc lenght 0
    Nov 13 14:45:48 Sam-iPad kernel[0] <Debug>: 285568.185043 wlan.N[12107] AppleBCMWLANCore:startRoamScan(): 3365 Delaying RoamScan; because  Join Mgr Busy 0 isWaitingforIP 1
    Nov 13 14:45:49 Sam-iPad kernel[0] <Debug>: IO80211AWDLMulticastPeer::queuePacket ff:ff:ff:ff:ff:ff alllocate queue for ac 0
    Nov 13 14:45:58 Sam-iPad kernel[0] <Debug>: 285578.034874 wlan.N[12108] AppleBCMWLANCore:startRoamScan(): 3365 Delaying RoamScan; because  Join Mgr Busy 0 isWaitingforIP 1
    Nov 13 14:45:58 Sam-iPad kernel[0] <Debug>: 285578.060369 wlan.A[12109] AppleBCMWLANNetManager::handleDelayedPowerManagementTimeout():  Timed out waiting for IP address, entering powersave mode: 2
    Nov 13 14:45:58 Sam-iPad kernel[0] <Debug>: 285578.075638 wlan.A[12110] AppleBCMWLANNetManager::checkRealTimeTraffic():  now 285578.075633250 num entries 4
    Nov 13 14:46:06 Sam-iPad kernel[0] <Debug>: 285586.747324 wlan.N[12111] AppleBCMWLANCore:startRoamScan(): 3379 starting RoamScan; MultiAPEnv:0 isdualBand:1 isOn5G:0
    Is anyone else aware of this problem?

    iPhone 4s: iOS 6
    iPad 2 iOS 6
    iTunes 10.7.0.21
    Windows 7 Ultimate i5 / 8G RAM
    my iDevices will not sync anymore unless it is plugged in USB and turn it off and back on again while connected. is there going to be a fix for this? btw good job apple...-.-

  • T61 Wireless Connectivity Issue - can not connect with secure wireless sites

    I have a T61 using Windows XP. The internal wireless card was factory installed and has not been upgraded.
    My home Internet is Comcast high-speed.
    When I take my laptop to a coffee shop, business or other location with a secure wireless network that requires a password, I have not been able to log on. I can see the wireless networks available and can click on the appropriate one, but I never get a window/pop-up box/screen in order to allow me to enter the wifi network's user name and password.
    Is this a firewall issue, wireless card issue...or?
    I can access unsecured wireless networks where a password is not needed.

    Hi lisapapp!
    One more thing to check: Is your Windows XP up to date? Older XP releases do not support the newer wireless encryption types which are now in common use (WPA, WPA2). Make sure you have SP3.
    I don't work for Lenovo. I'm a crazy volunteer!

  • Satellite U940 PSU6VA - Wireless connectivity issues

    _*My specifications:*_
    *Model:* Toshiba Ultrabook (Satellite U940 PSU6VA-00S002)
    *Operating System:* Windows 8.1 x64 (upgraded from Windows 8 x64)
    *Wireless adapter:* Intel(R) Centrino(R) Wireless-N 2200
    *Wireless adapter driver version:* 15.10.0.12 (which is the latest for my device)
    I have had this Ultrabook since February 2013, and throughout that period I have always had wireless connectivity issues, even after performing a factory reset. My wireless icon fluctuates between three states:
    * Internet access
    * Limited (in which case I cannot connect to the internet or any device on the network)
    * Not connected - connections are available (and if I try to make it connect to the network, it will fail)
    Sometimes my computer would instantly reach the "Internet access" state upon startup, and would remain in that state. Other times, it would be "Limited" for several minutes after starting up my computer before it finally connected, and even then the connection would drop out every now and then. At the worst, it would remain either "Limited" or "Not connected" indefinitely, no matter how many times I reset my wireless adapter or restarted my computer.
    Until recently, I had always thought that these issues occurred randomly. However, I recently noticed that I always have a perfect connection whenever there are no other computers connected wirelessly to my home router, and I always experience issues of varying degrees when there is at least one other computer (or even a smartphone) connected wirelessly to the router. If there is another computer connected to the router via an Ethernet cable, this does not cause any problems; it is only wireless connections that interfere with my computer.
    It is only this computer that has these problems; the other computers in my house never experience these issues, no matter how many computers are online. Also, my computer does not only experience these issues with my home router; it has the same issues on my university's wireless network.
    My question is, how can I fix this? Is this a known bug, or is my wireless adapter defective? I know I can connect using an Ethernet cable where possible (I never have problems with Ethernet connections), but this is not always possible at university.

    > {quote:title=TomDexter wrote:}{quote}
    > Intel page provides the Wlan driver for this WLan card and its v16.7.0 for Win 8.1
    I just checked the page you linked to, but it recommends that laptop users obtain their drivers from their OEM rather than from Intel.
    I had already checked for driver updates through both Toshiba Service Station and Device Manager (and checked both again just now). Toshiba Service Station tells me that there are no updates available, and Device Manager tells me that "the driver software for your device is up to date".
    Should I update to Intel's latest driver anyway? If so, should I also install the Windows 8.1 version of "Intel PROSet/Wireless Wifi Software"?
    > {quote:title=TomDexter wrote:}{quote}
    > I would recommend you to check the Wlan functionality and performance testing each Wlan standard 802.11 B / G and N and additionally check the different Wlan channels (1-11)
    I have found the WLAN channel setting in Device Manager and I will test it when I get the chance. But how do I change the WLAN standard?
    Message was edited by: Justinian

  • C4780 Wireless problem

    I have bought yesterday a C4780 wireless printer. After almost 2 hours trying to install it, I gave up. In the middle of the process, a got a window message saying that the printer couldn´t be found. I´ve tried so many time to plug/unplug the USB cable, but it didn´t work. The interesting is that the printer appears in the list provided.
    I´m using a level one router with window vista. Another problem is that my SSID wasn´t found.
    What should I do?
    Thanks

    OK, you should have the wireless on at all times.
    Please print a Wireless Network Test from the front of the printer.  Let me know about its self-tests (pass or fail) and its IP address.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • Linksys Wireless Camera issues

    When i install my linksys wireless Wvc80n wirelss camera I lose my wireless connection on my laptop to the internet itermittently until I unplug the camera then its back to normal.

    That sounds, Most likely,  a wireless signa issue.
    You can change that in the router.   open a browser, and go to http://192.168.1.1
    user name is admin.  and the password is most likely the serial number found on the service tag of your VZ router unless you changed it. Once you login succesfully, go to the top and hit wireless, then on the left basic security.   then go to option 3 which is channel  1, 6 and 11 and are the only channels you should try.
    So it will likely be set to auto, change it to 11 and put the check for keep settings even after reboot (Directly under the channel) and then hit apply.  after you hit apply,  test your connection out, if you notice a difference, leave it like that until the problem happens again, and if it happens again, go back into the router, and try channel 6,     test it out.  and then finally 1 if the first two don't work.
    Also take a look at page 2 of Actiontec's Wireless PDF File.  It gives you some idea's with regards to position and orientation of where the router sits and how it can best be positioned for maximum coverage.
      http://support.actiontec.com/doc_files/MI424WR_Rev(all)_Wireless_Networking_Guide.pdf
    One of the channels (1, 6 & 11) will allow both to function fine.  

  • Is there a fix for the MBP wireless dropping issue?

    I began to experience the Macbook Pro dropping wireless connectivity on my very 1st Apple in 2008.  At the end of the day my machine was replaced with a new Macbook Pro mid 2010.  It appeared to be working just fine until about 2-3 months ago when I started dropping my wireless printer connection.  I searched the internet hoping for a driver update from HP or something from Apple and each time I found something, the problem still existed.  I even thought that by upgrading to Lion would resolve any issues that I have with my MBP wireless connectivity issue.  After upgrading to buying a new router, new printer and upgrading to Lion; the wireless dropping issue still remains unresolved!  I know there are several hundred in not thousands of people who are having the same problem so what are we supposed to do?
    When my 1st MBP was replaced in 2010 I had to stop working because I was diagnosed with "Failed Back Surgical Syndrome" and was in the process of applying for disability.  Something in the back of my mind said that I needed to purchase Apple Care for this new replacement however I had used all of my savings & retirement to sustain life for me and my family that there was nothing for Apple Care.  If it weren't for my church and family I am not sure what I would do during the 18 months of no income while waiting for a decision only to receive an appeal until I findly stood in front of an Administrative Law Judge who heard my case and granted me disability.  Besides there was no way I could ask anyone for money to purchase a warranty for a top of the line laptop while the country was falling off an economical cliff.
    I broke down and called Apple Support and was told that I qualified for technical assistance regarding the upgrade to Lion a few weeks ago.  The tech on the phone had me run some disk utility tests and had me repair permissions which she said could be the cause of the problem.  I willingly went along with her in hopes that this was indeed the fix.  However, within 10 minutes of hanging up the phone my MBP began to drop it's wireless connection to my new HP printer and also the Internet.  Hence my question above is what I am really looking to have answered!  What is the fix to this problem that so many people are having issues with?  I couldn't afford to purchase Apple Care back in 2010 and I can't afford to purchase a new 2011 machine today if that truly is the fix!
    I will be disabled for the remainder of my life and I have grown dependent upon my computer to stay in touch with friends and colleges from work.  I worked for the IT Group at Wynn Resorts and I can say that the type of service Appple is providing it's customers is not what I learned over the past 25 years with Mr. Wynn.  Why can't Apple get the simple concept that it's customers are it's life line and keeps them in business.  I need help and I don't know what to do nor where to turn.  It would be different if Apple acknowledged the issue and said they were working on it however they aren't.  I plead to Apple to help me fix my notebook so I can stay connected to the outside world vs. couped up inside my home.
    Best Regards,
    Scott Leavitt

    I am simply lookig for some help not an argument.  I am not an RF specialist however have setup a few wireless networks in my tenure at Wynn Resorts.  I fully agree that wireless networking is an art and a science however the powers that be in Network Land have toughted wireless networking is the easiest and quickest way to get two computers to talk with one another.  As I previously said I have already turned one (1) MBP in for this problem and Apple decided to replace it because they could not fix the problem with my particular MBP.  This MBP was running Leopard when the problems started
    I am having a hard time believeing that there are several other devicces in my home that depend on a wireless network to operate and my MBP is the only one having an issue.  I took this a step further and decided to see what would happen if I tried to connect wirelessly via Fusion.  In Windows 7 I am able to print and scan to my hearts content without any issues.  I am able to browse the internet as much as I want.  I close Fusion and try to connect to my printer via wireless and nothing.
    In order to get Apple to help do I need to get a Network Analyzer and capture packets when I have these problems?  Out of the 1000 + posts is there a consolidation of which answer is the best?  BTW I am accessing the internet via a wireless connection using Fusion and Windows 7.
    In response to Linc's comments, I will look at the router specifications however I did not qualify that these devices are not using the wireless connection at the same time.  Right now I would guess there are maybe two (2) or three (3) at the most that are actively transmitting / receiving information. --  Thanks

  • Wireless Install Videos - Windows 7

     I wanted to share a few different videos we've created that show how to do a wireless install in Windows 7.  If you're not sure which video applies to you, watch the first one on the list. 
    Installing an HP Full Feature Printer Driver in Windows 7 (Wireless)
    This video shows you how to download and install a full feature printer driver. When you download your software, you can choose between a full and basic version of the software. The full featured driver is much larger, but is strongly recommended as it provides more features and functionality for your printer. The installation shown is a wireless setup using a USB cable.
    The steps shown may not match exactly what you see on your screen. For videos and help specific to your printer, visit www.hp.com/support or www.youtube.com/hpprintersupport.
    Install an HP Printer in a Wireless Network Using an Access Point in Windows 7
    This video will show how to download and install a full feature driver from HP.com on a wireless network using a wireless router or access point in Windows 7.
    Installing Your HP Printer Using a CD in Windows 7 - HP Laserjet Pro CP1025nw
    This video shows you how to install your LaserJet printer on a wireless network in Windows 7, using the CD provided with your printer. The printer shown is the HP LaserJet Pro CP1025nw.
    Installing Your HP Printer Using a CD in Windows 7 - HP Laserjet Pro CP1525nw
    This video shows you how to install your LaserJet printer on a wireless network in Windows 7, using the CD provided with your printer. The printer shown is the HP LaserJet Pro CP1525nw.
    Windows 7 Install (Wireless with USB and CD) - HP Laserjet P1102w
    This video shows you how to install your LaserJet printer on a wireless network in Windows 7, using a USB connection and the CD that was provided with your printer. The printer shown is the HP Laserjet P1102w.
    Wireless Windows 7 Smart Install - HP LaserJet P1102w
    This short video shows how to do a wireless install using the Smart Install feature on an HP Laserjet P1102w in all versions of Windows 7.
    This one isn't an install video, but is helpful if you're doing an install and you need the password to your wireless network.
    Using the HP Print and Scan Doctor to Retrieve Your Wireless Network Password
    Learn how to retrieve your wireless network password or key using HP's Print and Scan Doctor.
    Retrieving your network password is useful if your computer is set up on your network, but you can't remember your password for the network.
    I am an HP employee.

    This is a great collection of support videos.  Thanks for compiling them into one place.
    ↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

  • SP2010 Foundation Post Install issues on development workstation - Database and Services

    Just recently installed SP2010 Foundation for a development workstation.  Platform isWin7 X64 pro, SQL 2008 (Developer edition)
    (1) Looks like search has some configuration issues.  This is in the Windows event log
    The Execute method of job definition Microsoft.SharePoint.Search.Administration.SPSearchJobDefinition (ID 38eefca2-d092-47f4-a833-23f8280c5f63) threw an exception. More information is included below.
    The device is not ready.  
    (2) In Central Admin > Servers in Farm
    Status - "Upgrade Available", 
    (3) In Central Admin > Manage Database Upgrade Status
    Sveral of the Datbase(s) mention that upgrade is recommended, but one in particular mentions that the DB is too old?
    WSS_Search_GHHTY
    SPSearchDatabase
    Database is too old and upgrade is required
    Huh?  
    (4) Looking at my local SQL 2008 instance that SP2010 created, I see several DB's with "Config" in the name along with a guid on the end of the name.  Is the result of re-running the configuration wizard several times while
    I was correcting install issues?

    here is question, i am assuming its fresh install not upgrade...
    when you run the config wizard( you mentioned many times), which option you select from 2nd try to on ward....cannot disconnect this server from farm?
    are you using any script to install ?
    I would say run the config wizard without disconnecting and this server will host CA option.
    from the central admin > manager server in farm...on top you will see farm version and config database name. note it
    from the Manage database Upgrade status page note all the db names
    now match it on sql and keep those and all other should gone now as a clean process.
    Please remember to mark your question as answered &Vote helpful,if this solves/helps your problem. ****************************************************************************************** Thanks -WS MCITP(SharePoint 2010, 2013) Blog: http://wscheema.com/blog

  • Mac OSX: Flash CS3 Font Install Issues

    Hi,
    I have a Mac Powerbook G4 with OS X installed and Adobe CS3.
    I've installed a font. The font works in Photoshop and Illustrator
    but not in Flash CS3. Why? I've put the font in the Library/Fonts
    folder and the User/Fonts folder and it still doesn't show up in
    Flash. Apparently this is a problem for a number of people see
    another forum here:
    MAC
    OSX: Flash CS3 Font Install Issues Forum
    Please let me know what to do to fix this. I need to be able
    to work with the font in all three applications Flash, Photoshop
    and Illustrator.

    Hi davidd61713525,
    Sorry for not getting back to you sooner.
    Unfortunately, it looks like something is wrong with the file system and the installer can't see the root drive to install to.  A Google search returns numerous results affecting various products and the recurring theme is that something is wrong with the disk.  There are many recommendations from various sources, but nothing definitive.
    Here's a similar thread over on the Apple forums:
    Broken Installer Permissions | Apple Support Communities
    And a similar older one:
    http://forums.macrumors.com/showthread.php?t=1203509
    I would try the following options:
    Try using the PKG installer. This is used Mac SysAdmins to install Flash Player within their organization and uses a slightly different installer path, which may or may not work.
    Some people have had success with disk and permissions repair some have not.  You can try running a disk and permissions repair.  After the disk and permissions repair is complete, reboot the system and try to install again using either the online installer (get.adobe.com/flashplayer) or the offline installer, posted at the bottom of the Installation problems | Flash Player | Mac page in the ‘Still having problems’ section.
    If these options do not work, I'd reach out to Apple support to see if they have a suggestion.  If you do find a resolution to this, please let me know.  I'll be happy to share it with people that encounter the problem in the future.
    Maria

  • Re-Installing Issue

    Hi,
    I have a G5 I had to re install and erase my HD cause I had issues, now that i am rebuilding the system it won't let me install FCS, I get to the DVDP disc and it says Installation failed.... I tried it a few time and I get the same error. Can anyone shed some light on this please?
    thanks
    P

    Welcome to the forum!
    Made sure the disks are clean? I'd call Apple on an install issue if it's new or if you suspect a damaged disk and you're the registered user.
    Which OS are your running? QuickTime Version?
    Jerry

  • Webutil install issue

    Hello,
    I have a strange WebUtil install issue on 10gIAS 10.1.2.0.2. I downloaded the 1.0.6 WU version and put it into a webutil directory under forms (which the pre-configuration of AS seem to assume) and when I call the forms servlet with ?config=webutil the "RegisterWebUtil - Loading WebUtil Version 1.0.6" shows but the main applet doesn't load. The webutil HTML template is found and looks OK in View Source but no applet. The config section has a archive_jini but it behaves as if the main jar can't be found(?) Nothing extra in the jinit-console, even at log level 5. webutil.cfg is copied to forms/server and frmwebutil.jar to forms/java.
    Suggestions appreciated,
    Nik

    Hi,
    Can you check Vitual Path of WebUtil in the config file ..\forms\server\forms.conf?
    I would like to see your files
    ..\forms\server\default.env
    ..\forms\server\forms.conf
    BACH

Maybe you are looking for