HP LaserJet P4015 stopped responding

We have rolled out HP LaserJet P4015 in our entire School District. We have printer communication issue with this printer. It just stopped responding. have tried different versions of Driver, we have updated the firmware, too. Everytime we change the driver it will work and then stopped again. Is there anybody here experiencing the same problem?

I am having the same problem with my P2015dn. Looking at the posts indicate a number of models are having this problem. Mine workvia USB just fine. I can ping the printer, the router shows the printer, the printer shows ready but won't print and if you delete the printer and try and then go back to add printer - it is not found. Judging by the recent flourish of posts, I expect the answer will have something to do with the recent Windows Updates but nothing yet on the HP or Microsoft sites - just a lot of frustration and time wasted on the part of their customers! I hope some one has ideas

Similar Messages

Powervault 124T stop responding at a precise hour

Good day to all.
I apologize if my English seems strange but I'm French and not that fluent.
We have a LTO4 powervault 124 T that is behaving strangely : the network stops responding at 3:30 PM GMT and doesn't restart until we power cycle the device. But the backup is working perfectly so there is no issue regarding data backup. The problem is limited to the network.
I tried to change the IP address, toggle between DHCP lease and fixed IP address, no result.
Depending on the time we cycle power, the network stops the same day or the day after, but always at about 3:30 GMT (it can be a few minutes before that time, but it's the time when I receive the alarm from our monitoring system).
I found that if I telnet to the PV address, I get an response from a 'pinon debug terminal' but I don't know the password.
So my questions are :
Can someone here direct me to a possible solution to get the network back to a stable state ? I think about upgrading the FW but I'm surprised when I read that the file I can download from Dell website is 320 Mb big.
How to know the telnet password ? Not sure it can help me troubleshooting the problem but I'm curious to see what this terminal can provide.
Best regards.

Hi again,
I still suspect a faulty USB port.
Your response is still a bit confusing, so just to be sure:
- Did you also try a USB port on the backside of your Mac?
(if your keyboard is usually connected to the frontside, and you normally plug the mouse into the keyboard, it doesn't help to try testing it by plugging it directly in the front port, if this port is faulty, it's still the same port. If this is your situation, definitely try a port on the back)
- When you connected the other (older) mouse and keyboard, they were initially not recognized, but they were after rebooting, so did they function properly after this reboot? Did you connect these on the same port you usually connect your Logitec and keyboard to, or did you try different ports?
- Do you have access to another mouse and or keyboard, which is 100% sure known to work perfectly on another computer? If yes, try this on your mac.
- When you tried the mouse and keyboard on the Macbook Air, did you try it long enough to be 100%sure they work fine? Let's say at least 3-5 times longer then the average freezing intervals on your mac? (If you just tested briefly, you can't be sure.)
- How does it freeze? The pointer just stops moving? or do you see a spinning beachball?
Another thing:
You are posting in the Power Mac forum
you should actually post this in the Mac Pro forum
https://discussions.apple.com/community/desktop_computers/mac_pro
although they look similar, the older Power Mac line were equiped with IBM PPC processor(s), and the newer Mac Pro line features Intel CPU's.
You will likely get more help if you post in the right forum, which is more active.
You can refer to this thread though

ITunes 10.6.1 x64 regularly stops responding.

Hello -
My name is Erick and I'm an ACMT/Network Engineer; Apple-certified, but not Apple-employed.
I have experienced an issue with iTunes 10.6 in general that has not been resolved by the latest update to 10.6.1. Upon opening the iTunes application, it initially responds but within 15 seconds freezes and is Not Responding. The unresponsiveness lasts up to five full minutes, then the program begins working again. The issue appears to begin as the iTunes Match cloud icon begins animating and checking for updates to my music library.
The same situation also occurs regularly if/when I make changed to a Smart Playlist. The program stops responding for up to five full minutes, then works properly.
Here's some additional information about what I've already attempted in efforts to fix the issue. Does anyone have any suggestions or recommendations for how I might remedy this issue? While it's not crippling my use of the application entirely, it does cause unexpected headaches and delays, and it'd be great to fix it.
I've attempted to resolve the issue by opening a new library and using it temporarily to test, rebuilding the library by starting fresh and importing from my iTunes Library file, and I've also attempted to use iTunes 10.6.1 from a different user account. Finally, I loaded iTunes 10.6.1 onto my external troubleshooting drive which is running the same OS. I've seen the issue persist in each situation. I've also attempted to run iTunes in 32-bit mode as I experienced some success with this fix related to other issues in the past.
I am using an iMac 27" with the quad i7, 16GB, and a 1TB hard drive. All of my music is on iTunes Match and none of it is being stored locally on this machine. My TV and Movies are being stored on an external 2TB drive, as is the iTunes Library file itself.
I would be happy to provide any logs or additional information that could help resolve this problem. I appreciate any assistance and hope to have this resolved at some point. My iMac is typically on 24/7 as it operates as a streaming server for services like StreamToMe, SugarSync, Plex, and other file services. Additionally, iTunes is typically open 24/7 to provide streaming ability to my Apple TVs (1080p versions), though I do have a scheduled task which exits and re-opens iTunes at 4:30AM to prompt syncing of my iOS devices before I head to work (putting the latest unwatched media on them).
I'm sure some of this is unnecessary or extraneous information, but I wanted to be thorough in my explanation and context. Thanks again for your assistance, everyone.

I have resolved my issue with iTunes' unresponsiveness and wanted to post the solution for anyone who might be experiencing similar symptoms. It was really quite simple to fix, I just didn't see it for what it was:
iTunes Match was causing iTunes to stop responding for several minutes at a time, and several times a day.
iTunes Match - which also forces Genius Mode to be on (something that used to cause my iTunes 10.5 to freeze before I turned it off) - would regularly attempt to refresh my database of 21,000 matched songs (none of which were stored on the computer - just in the cloud) and when it would attempt to update or refresh that library, the program would stop responding.
The constant queueing of iTunes Match / Genius also caused iTunes to consume a significant amount of RAM - something that was also causing issues and which I posted about in another discussion.
So, the simple solution was this: Turn iTunes Match off and iTunes quits freezing.
Now, that of course completely eliminates the usefulness of iTunes Match since the music is no longer accessible on this machine in this iTunes Library. So how to restore its usefulness without recreating the problem? Slightly more aggravating, but still working right: I created a separate, fresh new library and named it iTunes Match. When I need music, I hold option when selecting the iTunes app and select my Match Library, which has NOTHING else in it but iTunes Match. When I'm done with the music, I switch back to my 24/7 media streaming library that has my 2TB of TV Shows & Movies (and device sync relationships) in it.
It doesn't seem like iTunes Match causes freezing and RAM ballooning all by itself, it just seems like in a library that's also full of other stuff, it's the final straw that kills the performance. Split the libraries up and things seem to work really well in both.
Not a perfect solution, but until the next release of iTunes, this may be the best bet. I hope this helps someone else out there, but it at least cleared up my issue. Thanks for reading.

I've only had my iphone 5s for a week. I keep getting an error message of "Server has stopped responding." I need the server to work. Does anyone know if there is a "fix" for the problem? Other wise, I probably best return for a refund and get a Samsung.

I've only had my iphone 5s for a week. I keep getting an error message of "Server has stopped responding." I need the server to work. Does anyone know if there is a "fix" for the problem? Other wise, I probably best return for a refund and get a Samsung. Thanks

sandyzotz wrote:
Other wise, I probably best return for a refund and get a Samsung.
Unlikely. Based on the complete lack of detail of the issue provided it is entirely possible the same issue would occur.
Unless and until the user provides some actual details of the problem, there is nothing the indicate that the issue is with the iPhone.

Quicktime Export Error: "An output module stopped responding."

I'm experiencing an odd export error whenever I use any Quicktime codecs:
"After Effects error: An output module stopped responding. The file may be damaged or corrupted. You may need to restart After Effects."
Similarly, Adobe Media Encoder hangs when outputting to Quicktime codecs. Neither program makes any progress at all before the hang occurs. At that point, I have to manually "end task" to exit. Also, it doesn't seem to matter what I try to export. In AME, for example, I can simply try to convert one video format to another and have it hang, so I don't think the problem is due to a problem with the source settings or effects. Also, I'm not attempting any multiprocessing since I don't really have enough RAM for that. Other output modules work, so I'm just exporting image sequences for the time being.
System specs:
Windows 7 64-bit
Intel i7-2600k processor
8 GB RAM
GTX 580 GPU
Software:
Adobe CS6
AE Plugins include Tracode Suite 12 and Optical Flares
Quicktime 7.7.3
Any thoughts on this? I've seen very few references to this error in other places, and not really found a solution that seems to apply to my situation. Thanks in advance for your help.
Josh

Thanks for setting me in the right direction. Clicking through to the 25 :: 101 error page (http://myleniumerrors.com/2013/01/06/25-101-4/) led me to a reference about other software, such as remote access software, using the same ports that AE needs for communication with its various processes. In my case, LogMeIn was the culprit. I had no idea that AE even used TCP for these types of operations, so that's very helpful to know.
*EDIT*
That worked temporarily, and now it doesn't work. I ran into a similar effect when I first disabled the Windows Firewall. But of course, as I type this and piddle around, it works again. It SEEMS like if I open AME and click into the output settings and scrub through the video preview, it makes everything work when I go to actually export. That's exactly the type of thing I would say is completely unrelated under normal circumstances, but at the moment all I know is that it is currently working and I don't want to test anything else until I finish the rendering I need to accomplish today. I'll work on it more later and post an update at that time.
Thanks,
Josh

Firefox 15.1 stops responding for no apparent reason!

As the title says, Firefox 15.1 stops responding for no apparent reason!
I just did a re-format of my system disk and I re-installed Vista 64-bit on it. I have obviously re-installed everything from Windows updates to chipset, graphics and sound drivers. I also pulled down the latest and greatest version of Firefox which at the time is 15.1. So installed that too.
Every now and then Firefox just stops responding for no apparent reason. It looks like it is processing the request (after clicking a link etc.) but it then it's just a silence... nothing happens!
It doesn't even say it can't load the page and Windows doesn't even say that it has stopped responding. Not even after I click like crazy on the Firefox interface like different buttons and tabs and on the web page... not even then does it say "not responding" in the title bar of the window, which is usually the case when you deal with programs that are not responding immediately (you get that dialog that asks you if you would like to close the program or search for solutions online). Just nothing!... it's only quite and does nothing....
At the same time, all other programs are working flawlessly, such as the Explorer (Windows Explorer), or even Internet Explorer. And Internet connection is not lost!
I have no add-ons or extensions installed whatsoever. I just installed Firefox! I haven't even had the time to install Java yet. All I have is Adobe Flash player. That's the only extra. Otherwise it's in its' original form, default settings, etc, etc, etc.
Why is it acting up like this?...
I'm surprised that there even is such a thing as Firefox 15. This one came at the end of August, correct?
I have been on Firefox 14.x something before I re-installed Vista. For a good reason so! This is why I hate the new update model of Firefox and I don't jump on the next train (version) unless it's safe and I'm having compatibility issues with the one I use at the moment. This is why my first step after installing Firefox always is to disable automatic updates! I hate it when the software vendors are pushing out their latest software versions forcefully.
Frankly, I think this new Firefox version of yours is crap. It's not properly tested and it doesn't belong in the official release channel. This is more like a nightly build or something. It probably has some memory leak, despite the promises made by Firefox engineers that it will not have memory leaks and that it would be the fastest version of Firefox ever. I don't really need a faster browsing, I need a stable browser for reliable browsing. The speed of this Firefox version is close to ZERO! When it's not responding at all...
I have been a fan of Firefox since 0.8. I will be probably ditching this latest version and going back to an older version like 13 or 14 that's more closer to the reality and not in this fantasy world of fastest, greatest, latest, version this, version that, latest features. I just want a browser that works man!... I'm getting tired of Firefox. I may even ditch it altogether in favor of.... I don't know.... Safari?... Chrome?.... I might even go back to Internet Explorer after like 12 years of absence.

please try to uninstall the adobe flash plugin from the windows control panel. afterwards manually delete any leftover files in ''C:\Windows\SysWOW64\Macromed\Flash'' and download & install the plugin again (uncheck the option to install the bundled security software): www.adobe.com/go/getflashplayer

Windows Server 2012 - Hyper-V - iSCSI SAN - All Hyper-V Guests stops responding and extensive disk read/write

We have a problem with one of our deployments of Windows Server 2012 Hyper-V with a 2 node cluster connected to a iSCSI SAN.
Our setup:
Hosts - Both run Windows Server 2012 Standard and are clustered.
HP ProLiant G7, 24 GB RAM, 2 teamed NIC dedicated to Virtual Machines and Management, 2 teamed NIC dedicated to iSCSI storage. - This is the primary host and normaly all VMs run on this host.
HP ProLiant G5, 20 GB RAM, 1 NIC dedicated to Virtual Machines and Management, 2 teamed NIC dedicated to iSCSI storage. - This is the secondary host that and is intended to be used in case of failure of the primary host.
We have no antivirus on the hosts and the scheduled ShadowCopy (previous version of files) is switched of.
iSCSI SAN:
QNAP NAS TS-869 Pro, 8 INTEL SSDSA2CW160G3 160 GB i a RAID 5 with a Host Spare. 2 Teamed NIC.
Switch:
DLINK DGS-1210-16 - Both the network cards of the Hosts that are dedicated to the Storage and the Storage itself are connected to the same switch and nothing else is connected to this switch.
Virtual Machines:
3 Windows Server 2012 Standard - 1 DC, 1 FileServer, 1 Application Server.
1 Windows Server 2008 Standard Exchange Server.
All VMs are using dynamic disks (as recommended by Microsoft).
Updates
We have applied the most resent updates to the Hosts, WMs and iSCSI SAN about 3 weeks ago with no change in our problem and we continually update the setup.
Normal operation
Normally this setup works just fine and we see no real difference in speed in startup, file copy and processing speed in LoB applications of this setup compared to a single host with 2 10000 RPM Disks. Normal network speed is 10-200 Mbit, but occasionally
we see speeds up to 400 Mbit/s of combined read/write for instance during file repair
Our Problem
Our problem is that for some reason all of the VMs stops responding or responds very slowly and you can for instance not send CTRL-ALT-DEL to a VM in the Hyper-V console, or for instance start task manager when already logged in.
Symptoms (i.e. this happens, or does not happen, at the same time)
I we look at resource monitor on the host then we see that there is often an extensive read from a VHDX of one of the VMs (40-60 Mbyte/s) and a combined write speed to many files in \HarddiskVolume5\System Volume Information\{<someguid and no file extension>}.
See iamge below.
The combined network speed to the iSCSI SAN is about 500-600 Mbit/s.
When this happens it is usually during and after a VSS ShadowCopy backup, but has also happens during hours where no backup should be running (i.e. during daytime when the backup has finished hours ago according to the log files). There is however
not that extensive writes to the backup file that is created on an external hard drive and this does not seem to happen during all backups (we have manually checked a few times, but it is hard to say since this error does not seem leave any traces in event
viewer).
We cannot find any indication that the VMs themself detect any problem and we see no increase of errors (for example storage related errors) in the eventlog inside the VMs.
The QNAP uses about 50% processing Power on all cores.
We see no dropped packets on the switch.
(I have split the image to save horizontal space).
Unable to recreate the problem / find definitive trigger
We have not succeeded in recreating the problem manually by, for instance, running chkdsk or defrag in VM and Hosts, copy and remove large files to VMs, running CPU and Disk intensive operations inside a VM (for instance scan and repair a database file).
Questions
Why does all VMs stop responding and why is there such intensive Read/Writes to the iSCSI SAN?
Could it be anything in our setup that cannot handle all the read/write requests? For instance the iSCSI SAN, the hosts, etc?
What can we do about this? Should we use MultiPath IO instead of NIC teaming to the SAN, limit bandwith to the SAN, etc?

Hi,
> All VMs are using dynamic disks (as recommended by Microsoft).
If this is a testing environment, it’s okay, but if this a production environment, it’s not recommended. Fixed VHDs are recommended for production instead of dynamically expanding or differencing VHDs.
Hyper-V: Dynamic virtual hard disks are not recommended for virtual machines that run server workloads in a production environment
http://technet.microsoft.com/en-us/library/ee941151(v=WS.10).aspx
> This is the primary host and normaly all VMs run on this host.
According to your posting, we know that you have Cluster Shared Volumes in the Hyper-V cluster, but why not distribute your VMs into two Hyper-V hosts.
Use Cluster Shared Volumes in a Windows Server 2012 Failover Cluster
http://technet.microsoft.com/en-us/library/jj612868.aspx
> 2 teamed NIC dedicated to iSCSI storage.
Use Microsoft MultiPath IO (MPIO) to manage multiple paths to iSCSI storage. Microsoft does not support teaming on network adapters that are used to connect to iSCSI-based storage devices. (At least it’s not supported until Windows Server 2008 R2. Although
Windows Server 2012 has built-in network teaming feature, I don’t article which declare that Windows Server 2012 network teaming support iSCSI connection)
Understanding Requirements for Failover Clusters
http://technet.microsoft.com/en-us/library/cc771404.aspx
> I have seen using MPIO suggests using different subnets, is this a requirement for using MPIO
> or is this just a way to make sure that you do not run out of IP adressess?
What I found is: if it is possible, isolate the iSCSI and data networks that reside on the same switch infrastructure through the use of VLANs and separate subnets. Redundant network paths from the server to the storage system via MPIO will maximize availability
and performance. Of course you can set these two NICs in separate subnets, but I don’t think it is necessary.
> Why should it be better to not have dedicated wireing for iSCSI and Management?
It is recommended that the iSCSI SAN network be separated (logically or physically) from the data network workloads. This ‘best practice’ network configuration optimizes performance and reliability.
Check that and modify cluster configuration, monitor it and give us feedback for further troubleshooting.
For more information please refer to following MS articles:
Volume Shadow Copy Service
http://technet.microsoft.com/en-us/library/ee923636(WS.10).aspx
Support for Multipath I/O (MPIO)
http://technet.microsoft.com/en-us/library/cc770294.aspx
Deployments and Tests in an iSCSI SAN
http://technet.microsoft.com/en-US/library/bb649502(v=SQL.90).aspx
Hope this helps!
TechNet Subscriber Support
If you are
TechNet Subscription user and have any feedback on our support quality, please send your feedback
here.
Lawrence
TechNet Community Support

Trackpad on MBP randomly stops responding

Hi
In the last few days I've had a recurring problem:
Randomly and without any obvious context in terms of actions, apps etc, my trackpad simply stops responding.
I have all options enabled on the trackpad, such as soft click+drag, and the problem has so far only occured when performing that: drop'n drag.
It get's stuck and I cant release whatever I've grapped.
I am now only able to use the keyboard and have to reeboot to be able to use the trackpad again.
After reboot the problem returns randomly after a while.
I can't think of any recent software updates or additions that have coincided with the problem, except installing Livedrive Briefcase recently.
The problem however does not specifically occur when working with that (though Livedrive is set to run i the background).
Any suggestions?
Edit: The problem occurs more and more often, usually after I have closed the lid (sleep). Also, I am able to use my Magic Trackpad, which in turn brings the build in trackpad back to working!
MBP: 15" 2.4 Ghz Intel Core i5 (dual core) 2010
System: 10.7.3.
HDD: 240 Gb SSD with 91 Gb of free space

Hope the information from the below linked article helps.
Cleaning the trackpad with a damp microfiber cloth may help.
http://support.apple.com/kb/TS1449
Best.

Keyboard/Trackpad stop responding; OS still functional

Hi
I recently got a new retina Macbook pro 13" on Tuesday (arrived Thursday). Everything has been functional until late on Friday, where the keyboard and trackpad input stopped responding. The operating system in the background continue to work (I was watching a youtube video at the time which kept playing, and a file I was transferring via SFTP gave a notification when complete). While the system is in this unresponsive input state, plugging a usb mouse/keyboard does not work - they otherwise work fine. To resolve, I had to reboot the laptop through via the power button.
There is no messages in the console that suggests anything obvious in the Console, but maybe i'm just missing something.
Anyone else experienced this?
OS X 10.9, late 2013 rMBP 13".

Many people are experiening this problem rght now. It is not due to the new MacBook you bought but rather that the new operating system "Mavericks" has some glitches. They should be fixed soon so be looking for an update. Best of Luck!
David

Apple remote and built-in trackpad stop responding

I have a Macbook Pro - late 2011 - and have upgraded to Mountain Lion the day it was released. I bought a brand new Apple remote and paired it with my MBP. Today, as usual, I used an HDMI cable to connect my MBP to a LED TV and started giving a lecture based on a Keynote presentation I created full of videos snippets and the like that I sometimes pause using the remote. All of a sudden the remote - which had been previously paired with my computer - stopped responding. I immediately switched to the arrow keys on the keyboard and finished the lecture. I also noticed that the built-in trackpad had stopped responding to multiple gestures.
Has anyone been experiencing these problems? And is there a solution? I have searched high and low, but to no avail.
TIA

Found a solution!!!
Reset the System Management Controller.
Now eveything is working as expected!

[SOLVED]MacBook Air (3,2) keyboard and trackpad stop responding int...

Hey guys, I've now got arch running on my air perfectly I think, except for a random loss of trackpad and keyboard input. It happens even with a usb keyboard. I'm not sure if the whole laptop is freezing or only the inputs stop functioning, I believe it is the latter because things that blink or move onscreen like the cursor keep blinking. It happens both in X and out. I have no idea where to start for diagnosing.
My current kernel line is this:
options "ro root=LABEL=arch arch noapic irqpoll acpi=force noefi"
I'm using nouveau but it also happens using fbdev. I can't get nvidia to work, it just blacks out the screen when starting X.
Any hints are welcome
EDIT: It just happened again, this time just after I clicked on a tab in firefox. I hit refresh, so the spinning circle came up on the tab, and the windows partially reloaded, then the mouse pointer stopped responding. The loading circle then stayed spinning indefinitely with the page failing to load any further.
Further information:
I removed noapic, irqpoll, arch (is that even a valid kernel option?) and noefi from the kernel line for this boot so that all that was left was acpi=force and it still booted happily. I'm not sure if I need any of those, I can't remember why I added them, probably to fix this keyboard issue. I'm booting through rEFInd so maybe I shouldn't have that noefi entry anyway.
Last edited by MisterAnderson (2013-05-20 05:30:28)

Solved, I removed all boot options and I'm guessing one of them was causing it.

Keyboard and trackpad stop responding briefly

I have a late 2012 (current generation) MacBook Air with all software up to date.
Every so often (sometimes multiple times per day, sometimes not at all) my keyboard and trackpad will stop responding to input for 1-10 seconds.
This has been happening since the computer was new.
Every time I go to the Console after I regain control I see the following:
[date] [time] Dock[processID]: no information back from LS about running process
There does not seem to be any prerequisite to that line, sometimes it's the only output written in the last 30 seconds.
Does anyone have any idea what's going on here?

If this were happening to me I would suspect a third party software conflict.

N460GTX Cyclone 768D5/OC blue artifacts and stopped responding

In the last month I have been having issues with my graphics card to the point that I can't play any game (at all, always stops responding), flash on websites cause video driver "stopped responding" error, vlc or media player videos cause stopped responding error, and any 3d screen saver preview in windows 7 causes artifacts and sometimes the stopped responding error. I can still do anything 2D fine but always haver little blue artifacts all over the screen. Current drivers are Nvidia 266.58, I have tried MSI drivers, Nvidia 260.* drivers and a set of older Nvidia drivers that supposedly didn't have the stopping issues but all had problems even after fully wiping the old drivers on every install.
Given the power issues I have seen in past threads I hooked up my Kill-a-watt again (I always baseline my systems on burn in with that), and I am finding my Wattage draw hasn't changed. Kill A Watt measures 188W avg Draw, Peak 250W. All drives set on RAID to spin up sequentially so I don't get the max draw you'd expect. I ran this with superPi, prime95 and memtest and all run fine with max draw I saw at 250W. I tried to run 3d benchmark tests but like all 3d apps they all crash after video card not responding error. When building this I carefully specd out the power supply with conservative numbers and multiple online calculators, this PS should be able to handle adding 2 more 1TB drives as long as I don't do SLI (don't have room in case anyway with RAID controller).
I have tried all I can think of to resolve this but nothing helps and I'm thinking it's got to be an issue with the card since nothing in my config has changed. Is it the card for sure and will need RMA?
Here are my specs:
Asus P6T WS Pro Mobo
Intel Core i7-930 Bloomfield 2.8GHz LGA 1366 130W
MSI N460GTX Cyclone 768D5/OC GeForce GTX 460 (Fermi) 768MB
6 GB DDR3 Kingston PC3-10700 8-8-8-24 timing
Kingston SSDNow V Series 64GB
Areca ARC-1120 RAID controller (configured RAID6)
4x Hitachi Deskstar HD31000 1TB 7200 RPM SATA
2x Samsung 1TB 7200 SATA
LG Black 10X Blu-ray Burner - Bulk SATA WH10LS30
Power:
XFX Black Edition P1-750B-CAG9 750W ATX12V v2.2 / ESP12V v2.91 SLI Ready CrossFire Ready 80 PLUS SILVER
Single +12V rail, +3.3V@24A, +5V@30A, +12V@62A, [email protected], [email protected]
From XFX site regarding this PS:
Tight voltage regulation (±3%)
Single, high power +12V rail (up to 62A/744W)
DC to DC voltage Regulator modules for +3.3V and +5V
High quality Japanese brand capacitors (105°C)
Solid polymer caps provide enhanced reliability and stability
Quiet 135mm ball bearing fan provides superior cooling
Supports multiple high-end graphic adapters (NVIDIA SLI & ATI CrossFire Ready)
Detachable modular cables
Energy Star 4.0 and RoHS compliant

Can you test the card in another system, yours or a friends?

Programs stop responding when I try to print to PDF

Info on what I'm using:
OS: Windows 7 Home Premium, SP1, 64-bit
Using Adobe Acrobat 8 Professional, version 8.1.0, up to date on updates
In this example, Microsoft Office 2007, no add-ons besides the Adobe Acrobat add-in that allows the creation of a PDF (but happens in all programs)
Problem:
I have always created a PDF from a Word/Excel document by printing to PDF (File --> Print --> Select Adobe PDF as printer --> Hit OK). Generally, the next step that occurs is a dialog box appearing that prompts me to select the location where I want to save the PDF and to specify a file name. Several weeks ago, this process stopped working. Now when I hit "Ok" to print to PDF, no dialog box appears and whatever program I'm in freezes/stops responding. Aside: I have tried printing to PDF from several other programs to see if the problem occurs in those as well, and it does -- printing to PDF freezes whatever program I am attempting to print from. (For example, MS Paint, Internet Explorer, Firefox, even Notepad)
Bullet point summary of what I have tried:
Canceling the print jobs in the Adobe PDF printer under "Devices and Printers" (jobs say they are canceling but never clear from the print queue unless I go into Services and restart my print spooler) and reprinting (freezes again)
Restarting computer (had no effect)
Setting Adobe PDF as my default printer (had no effect)
Setting TrueType font as "Native TrueType" under the Adobe PDF printer properties (Layout --> Advanced --> PostScript Options) (suggested in another thread I read about this problem; had no effect)
Checking to make sure that Word had not "adjusted" the security settings for the Adobe add-in (disabling it) under the Trust Center (Adobe add-in was still enabled, so nothing to change there)
Changing the printer properties to print directly to the printer rather than spooling first (had no effect)
Saving as PDF using File --> Save As --> Selecting PDF as file type (does work and is an acceptable substitute except when I need to convert multiple files to PDF at once and don't have time to go in to each individual file and convert it separately)
Repairing the Acrobat installation from within Adobe or from the Programs and Features menu under the Control Panel (does work, did fix the problem; but see followup below).
Repairing the Acrobat installation worked when I did it a few weeks ago. Once I went through the process, I attempted to print a document to PDF and it worked. But this morning when I attempted to print another document to PDF, it froze Word again and has been doing that ever since, so it does not seem to be a permanent fix. I had succesfully printed several documents to PDF this morning before it stopped working; the document I printed to PDF immediately before the document that froze was the exact same as the document froze in every way except the actual text (formatting, document objects, etc.). So I don't think it was something in the content of the document that "broke" the Adobe PDF printer.
I am sure I can try repairing the Adobe installation again, but I really do not want to have to do that all of the time. Does anyone know what the problem is? I haven't found anything that explains what's going on.

Anyone?

When I click on a file to view in Finder in the view as columns, Finder stops responding. If I use Finder in any of the other views, I don't have an issue.

When I go to finder and view as columns so that the right column will open a preview of the file, I get the endless spinning graphic and when I go to Force Quit, it shows that Finder has stopped responding. When I use Finder in any other view mode, I don't have that issue. This just started today. As far as I know, I haven't done any updates today that would cause the issue. I've restarted a few times. I'm running 10.10 on iMac (27-inch, Mid 2011). I when to updates in the App Store and saw there was an update for 10.10.1 and tried to run it twice now. It starts to install and says I have 7 minutes left and then at about 3 minutes, it just opens all my windows again and acts normally. When I go to "About this mac", I'm still showing 10.10 as the OS. Also, in the App Store, when I click on updates, it shows me 4 updates that I've already installed as ready to install. Not really sure what's going on nor why all the sudden this is an issue, but I use the preview mode in Finder all the time so I would love a fix for this. I've tried logging out and logging in as another user and the same issue with Finder happens with other users as well. I've emptied my trash bin as well.

Step one is to log into a newly created admin user account and see if the problem persists.
27" i7 iMac (Mid 2011) refurb, OS X Yo (10.10), Mavs, ML & SL, G4 450 MP w/10.5 & 9.2.2

HP LaserJet P4015 stopped responding

Similar Messages

Maybe you are looking for