HT1430 forgot my ipod touch in the car, and now all it does is brink on and off.. lights up, the apple logo come on but nothing else.. what do i do to reset it??
Well, i forgot my ipod touch in the car, and it snowed so bad and the temperature drop below zero. I thought my ipod was just battery dead, but when i charged it, only the Apple logo comes on and then blank screen. How can i reboot, or reset?? is the battery affected even though the phone wasn't wet??
As long as no moisture got in it... 1st thing to try is give it a few hours to warm up and fully charge the battery, then see if all is working by turning it on. Cold can effect the function. If still not working try a soft reset. Press and hold both the power and home buttons together until the Apple logo appears, about 15 seconds. Then release both buttons. If that does not work connect to your computer via cable go into iTunes and try Restore from backup. If all else fails, Restore to new. If that doesn't work contact Apple Genius Bar to have your iPod evaluated. Good luck.
Similar Messages
-
i have a nano 4th generation 8gb i have tried resetting it, i get the apple logo come up but nothing else happens. It will work in my docking station but as soon as i take it out it will not respond. any ideas, do i need a new battery?
It definitely sounds like your Nano needs a new battery at this point. You can have Apple replace it for a flat fee, send it into a third party service center to be replaced for much less, or you can purchase a new battery online and swap it out yourself if you feel up to it.
B-rock -
My iphone 4s got wet and shows the apple logo when charging but nothing else?
When i hold the home button in and its on charge the apple logo will appear for 5 seconds then go but nothing else, with out being connected for charge nothing happens.
It's water damaged. It is not in warranty. The warranty was voided when it got wet.
The replacement phone will inherit the balance of the original warranty or 90 days, whichever is longer. -
My iPod Touch shows the Apple logo splash screen and then turns off.
When I turn my iPod Touch on, the Apple logo is shown and then it turns off. After a few seconds, it shows up again. It continues to do this non-stop. Is there anything I can do? Any help would be greatly Appriciated
Let the battery fully drain. It may take awhile. After charging for at least an hour. If the iPod does not cycle on and off any more try:
iOS: Not responding or does not turn on
Otherwise it appears you have a hardware problem and an appointment at the genius Bar of an Apple store is in order. -
I tried to restart my iPad due to problems with a Pinterest app that took up a lot of storage in the cache...now the apple logo comes up but will not start...it has recently been charged
Try this - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
Cheers, Tom -
iphone fails to turn on. The apple logo shows up but nothing happens after that
Hi Haleynichole_99!
I have an article here with some troubleshooting steps that can help you resolve this issue with your iOS device:
iOS: Unable to update or restore
http://support.apple.com/kb/HT1808
Thanks for using the Apple Support Communities!
Cheers,
Braden -
My ippd touch isnt working i tried to reset it and the apple logo comes up then goes to a black screen. What else can I do?
Try connecting to your PC in Recovery Mode ane restore it. See this article for help on getting your iPod into Recovery Mode.
iPhone and iPod touch: Unable to update or restore
B-rock -
My ipod touch flashes the apple logo and the lock screen. How do I fix it?
My ipod touch 4th Generation will flash from the Apple Logo to my locked screen. Although when I plug in my headphones everything works perfectly. I have not had this ipod very long and i have already recieved a new one from Apple before. I have also tried reseting it as well.
First try restoring the iPod from backup.
Next try restoring the iPod to factory defaults/new iPod. -
I plugged my iPod into my computer to retore it and proceeded to do so as told. The only thing that happened after that was that the Apple logo keeps showing up and nothing else. My computer/iTunes no longer recognizes my iPod either.
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
Please help me!My Ipod only show the Apple Logo :(
Yesterday,when i use my Ipod,i was reset it,but when the logo Apple show again,it can not go to the Menu so i was plug it to AC Adapter and put it into Disk Mode but when i plug it to my PC ,the Ipod was show the Apple Logo(not in disk mode)So what i need do to restore my IPOD????Please help me!:(
have you tried this
http://docs.info.apple.com/article.html?artnum=61584 -
Apple logo comes up but ipod doesn't start
When I turn on the device the Apple logo comes up but the ipod doesn't start and go to the menus it just stays with the logo. When I hold down the play/pause on the click wheel to put it to sleep a symbol of a triangle with an exclamation point in the center comes up along with "www.apple.com/support/ipod." I tried rebooting it with Menu/select but nothing happens.
Unfortunately, on a "classic" iPod that uses a hard drive for storage, the most likely cause is a faulty hard drive.
You can try putting the iPod into Disk Mode
http://support.apple.com/kb/HT1363
If that works, connect it to the computer and run iTunes. iTunes may prompt you to do a Restore. This will erase the iPod, re-install its software, and set it to default settings. If the cause is data corruption or a software issue (and the hard drive has no physical problem), the Restore should fix it. -
please help ive tryed everything and i cant get my ipad to restore, ive discontecting it, defult starting it and no matter what my laptop keeps telling me that "this device is no longer connected " and on my ipad the apple logo comes up but the bar does not load please help !!!! i need my ipad for lectures
Hi rhiess,
Thanks for visiting Apple Support Communities.
It sounds like your iPad may not have restored fully. I'd recommend restoring it again with the iPad in recovery mode.
Use the steps in this article to place your iPad in recovery mode:
iOS: Unable to update or restore
http://support.apple.com/kb/ht1808
After placing your iPad in recovery mode, use the steps in this article to troubleshoot the connection between it and your computer:
iOS: Troubleshooting USB connection
http://support.apple.com/kb/TS1286
If you still don't see your device in iTunes, follow these steps for Mac or these for Windows.
Best Regards,
Jeremy -
HT1430 I turned my IPad off and now it will not restart. Apple logo comes up but no other screen.
I turned my IPad off and now it will not restart. The apple logo comes up but then it stops????
Did you try rebooting the iPad?
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.
If that doesn't work, see this.
iTunes: Restoring iOS software - Support - Apple -
My ipod touch is brand new and i just made my apple account and when i try to connect to the app store or imessage it cant connect please help
Try here:
Can't connect to the iTunes Store
Try changing he DNS to Google's 8.8.8.8 -
Updating ipod touch to os5.1 got an error message "cannot connect the ipod touch because the pairing record is missing" don't know what this means or how to fix but am stuck, only option is to answer ok and close the error box. Any ideas?
#1
- Try another cable. The cable for 5G iPod (lightning connector) seems to be more prone to failure than the older cable.
- If a 5G iPod
Iphone 5 lightning port charging problem - SOLUTION!
- Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar
#1.1 n/a because the errror message overrides it
#2 see #1
#3 iOS: Device not recognized in iTunes for Mac OS X
But could be caused by #1
#4 Covered by previous ones
#5 Obvious jpegs are photos and thus will not sync as videos. Also see:
iTunes: May be unable to transfer videos to iPhone, iPad, or iPod
iTunes: Frequently asked questions about viewing and syncing videos
#6 iOS: If you can't back up or restore from a backup in iTunes
First #7 See #6
Second #7 You have so many other problems resolve those first
#8 Resolve other problems first
Maybe you are looking for
-
Value Contract- Order- Invoice
Hi I have Created Value Contrace of Service material. I am Creating SO with ref. to Value Contract. Since material is Service material it doesnot have "loading Group" in material Master, so it Neither determine Shipping point in Sales Order nor allo
-
SAPCCMSR not started in sapmmc for trex
HI. We have TREX7.0 system. In trex mmc sapccsr agent is not running. As per some guides we registered sapccmsr agent using sapccmsr pf=<instprofile> -j2ee -r to central solution manager system in services sapccmsr agent is registerd and started but
-
I'm having a rather annoying issue with iPhoto, where certain photos are cropping to a very strange dimension when I export them. It doesn't affect all images, just some. They're not cropped in iPhoto, so I'm confused as to how this could happen. If
-
Cannot set up iCloud on MacBook Pro to find my iPhone??
I can login to MobileMe but not iCloud. Can't even get to the 'agree to terms' page before a window pops up saying 'iCloud is too busy to let new users log on'. It also has in red letters unrecognised username and password when both work fine on iTun
-
Hi all , I have configured an Purchase Order UWL link to launch webdynpro application which was newly developed. In which we are passing workitem id with that , so it will open the particular PO in WDA Application , The problem we are facing is that