HT3215 I have been sent a nano 6th gen to replace my original 1st gen due to the battery problem.  There was no charger lead or instructions so i am unsure whether we can charger using the old charger?

charge a 6th gen as ive been sent this by apple with no instruction or leads etc?

Yes, your original USB cord will work perfectly. I treasure my 1st-Gen Shuffle cord, because it has a much easier-to-grip dock connector than the new ones.

Similar Messages

  • I plugged my ipod nano 6th gen in to the latest version of itunes today and as soon as i plugged it it it turned on automatically as it should when i came back to it 5 mins later, picked it up and it felt warm and it wouldnt turn on. what should i do?

    I plugged my ipod nano 6th gen in to the latest version of itunes today and as soon as i plugged it it it turned on automatically as it should when i came back to it 5 mins later, picked it up and it felt warm and it wouldnt turn on. what should i do?

    I have the same problem and can't seem to figure out what the problem is. I rebuilt my iTunes library and still my 6G nano crahes whenever I load an AAC tune onto it.  MP3s and podcasts all work fine, it's just the AACs... 
    Just *loading* an AAC song will cause the Nano 6G to reboot as soon as it disconnects from Itunes. It will then reboot a few times and then go into recovery mode. :-(
    Karen

  • My ipod nano 6th gen just flashes the apple logo when plugged in but goes blank when not plugged in. i have tried changing format to fat32 but i can't on windows 7

    i have recently recieved an ipod nano 6th gen after the 1st gen recall, and out of nowhere it just started flashing the apple logo when connected to computer. Help please!

    Universal Serial Bus controllers
         Intel(R) ICH9 Family USB Universal Host Controller - 2934
         Intel(R) ICH9 Family USB Universal Host Controller - 2935
         Intel(R) ICH9 Family USB Universal Host Controller - 2936
         Intel(R) ICH9 Family USB Universal Host Controller - 2937
         Intel(R) ICH9 Family USB Universal Host Controller - 2938
         Intel(R) ICH9 Family USB Universal Host Controller - 2939
         Intel(R) ICH9 Family USB Universal Host Controller - 293A
         Intel(R) ICH9 Family USB Universal Host Controller - 293C
         USB Composite Device
         USB Root Hub
         USB Root Hub
         USB Root Hub
         USB Root Hub
         USB Root Hub
         USB Root Hub
         USB Root Hub
         USB Root Hub
    I'm not sure if it charged when I hooked it up to my roommate's computer, but it definately didn't register either. If I put it on the dock it plays so the port is fine, but that still doesn't help me sync it to my computer.

  • I have iTunes ver 10 on a PC with Playlists which do not sync to ITouch or Nano (6th Gen). All the music does not appear and the playlists do not appear at all. I have selected to manually manage music on the sum tab

    I have iTunes ver 10 on a PC with Playlists which do not sync to an Itouch or Nano (6th Gen). Also, all the music does not appear when I check entire library and there is enough memory on the device. When I select to manually manage music on the summary tab and selected playlists on the music tab nothing changes. Either way all the music isn't on either device and the playlists are not on either device. Please advise next steps. Thank you.

    Connect the device to the computer.
    In iTunes, select the content desired to sync.
    Sync.
    This is all described in the User's Guide, reading it may be a good place to start.

  • When listening to nano 6th gen with dock the audio book will make beeping noises and then switch to a song.

    While listening to my 6th gen nano on a JBL dock the audio book will make beep noises and then swith to a song on my nano.  Any idea?  Thanks.

    I saw your other post, but thought I would reply here as well. It is all about getting that headset seated all the way. If you can see any silver of the plug, it is not in far enough. Push harder. If it just won't go in, look in there to see if it is blocked. The bottom of the headset port is white, so if it appears all dark at the bottom... something is in there.
    i

  • Nano 2nd gen cant restore, says : itunes has detected an ipod in recovery mode, you must restore this ipod before it can be used in itunes

    Ipod nano 2nd generation: I cant restore, says, itunes has detected an ipod in recovery mode, you must restore this ipod before it can be used with itunes

    What do you mean you can't restore?  It's asking you to restore...
    B-rock

  • Tried playin my ipod nano 6th gen on my xbox 360. Everything was good till today when i was told how to get it  to work. Then all of a suden all the files and songs were gone on my ipod. now my network connection cant find my ipod.

    Does any body know how i possibly messed up my ipod. After i plugged it in today i think i uninstalled somthing i shouldnt have. None of the devices read it as an Ipod but a usb mass storage. Itunes cant even bring it up. Plz some help

    From the OP: "My old computer got a virus and when that happened all my music was lost. "
    They don't have the music on their computer so they cannot transfer the iTunes folder, from the computer to their iPod and then to the new computer. And if they try to enable disk use on the iPod it will erase all the music that is on it. The method you cited is moving the files in a data format using the iPod as a flash drive. It doesn't work if they are in music format. That is why I suggested Yamipod.

  • My Nano 6th gen's screen went blank--is there an easy way to reset this? This is my 4th unit within one year--come on Apple I expect more from you.

    My screen is black. But the unit works...I touch the black screen and can get music to play. I only use my nano during work out...nothing extreme. I received my original nano 12 months ago. Due to other issues this is my FOURTH nano...come on Apple...

    I don't think it's possible anymore. I'm mildly surprised you were able to keep podcasts in regular playlists this long - I thought this option disappeared back with iOS7.
    I do share your pain. I've finally grown used to having the podcasts in a separate app, but I still don't like it.

  • Sent Ipod nano 4 gen. Through the Washer! Help!

    When I plug it in to my computer it works fine, charges, and says "Connected". When I take it off, it works for about 6 seconds, then restarts it's self, over and over again! I have tried restoring it from Itunes but I don't want to download the newest version, (I like the one that I have). Can anyone help me?
    Message was edited by: Doah

    How long did you let it dry before you connected it to power? If it was less than 5 - 7 days in a cool, dry place, or 3 - 5 in a baggie with raw rice, then it is probably damaged beyond a reasonable repair.
    You can try letting is dry for five more days, fully charge it, and try again. If that doesn't work you'll probably need to get a new one.

  • My ipod nano 6th gen can't be identified by any computer, but it can still be charged in a wall socket. what's the problem in here? :'(

    There's this time that my ipod nano 6th gen stopped from being recognized on any computer, i tried all trouble shooting stuff but none of them worked, can you give me any solutions? i'm pretty desperate.

    Are you using a Macintosh or Windows?
    -Zeph

  • Ipod nano 6th gen askinh for resore every time i connect and after the restore not showing the sysnced song on ipod

    i have a ipod nano 6th gen, few days back when i tried to add few songs through iTunes it gave me error that it "can't connect to ipod . restore it" so i did and after that i synced al the songs and it showed that my my empty ipod has been up few GB's. after i disconnected , i could not see any song on the ipod . when it connected back the ipod the got same error about restore. i dont know what to do now , please help.

    Hello Singhindia,
    It sounds like you restored your iPod Nano when iTunes prompted you and it appears to sync. When you disconnect it and look at the content, the songs arent there, and when you plug it back into iTunes you get the same message again. I would recommend these troubleshooting sections from the following article to help isolate the issue to hardware or software:
    iPod nano: Error message saying that iPod 'could not be identified properly'
    http://support.apple.com/kb/TS3218
    Verify that iTunes is installed and updated
    Restart the computer
    Verify that Apple Mobile Device Support is installed
    Verify the device's USB connection
    Verify that the Apple Mobile Device Service and iPod service are both running
    Verify that the Apple Mobile Device Driver is installed
    Remove and reinstall iTunes
    If the issue continues, gathering iPod Diagnostics may be helpful for you or for support personnel in identifying the issue.
    Additional Information
    Certain phone connectivity software from vendors such as Samsung, Nokia, Bora, Novatel, and Sony may also cause this issue. If you have such software on your computer:
    Uninstall your Samsung, Nokia, Bora, Novatel, or Sony phone connectivity software and test. Contact the manufacturer of this software for assistance in doing this.
    Remove iTunes and all related Apple software by following this article (for Windows XP), or this article (for Windows Vista and Windows 7).
    After reinstalling iTunes, test the iPod nano.
    If you still need your phone connectivity software that was removed, reinstall this software and test your iPod nano to ensure it still functions with iTunes. Contact the vendor of your phone connectivity software if the issue returns.
    While the error message is different than you are seeing, the troubleshooting is relevant for you.
    Thank you for using Apple Support Communities.
    All the best,
    Sterling

  • Photoshop will not verify the serial number i have been sent.

    I have been sent a serial number, however photoshop Cs5 is not reading it as a valid code. PLEASE HELP.. as i need this program ASAP!

    Hi Tara,
    You can use this link to contact support : Contact Adobe Support
    On this page, do not change the country or region.
    Click on " I am having trouble downloading or installing my software".
    Then select " I am trying to use a single user product I bought from Adobe or another merchant"
    You will then have an option to chat with a support representative. You call support in Australia on 1800 614 863.

  • Ipod Nano 6th Gen damaged Apple won't repair...any options?

    I have had my Ipod Nano 6th gen for about 8 months and used it religiously during work outs...unfortunately I sweat a lot and apparently this will damage Ipod Nano to the point that Apple considers this to be outside the guidelines of normal manufacturer warranty.  I am a little frustrated by this as I spend a fair amount of money on Apple products every year.  Any advice on what I can do other than just sell it as damaged on eBay?

    The best thing to do is consult Genius Bar. But as you have already said Apple does not honor the cause of damage and therefore not eligible for replacement. I recommend to visit an apple technical support to confirm the initial assessment.
    You can try the out-of-warranty repair and determine how much it will cost you to repair. But try to weigh in cost of repair vs. a new replacement. Here is apple's statement about out-of-warranty repair.
    If you want to set up your iPod for the Out-of-warranty service, we recommend that you take your iPod to a local Apple Retail Store. Alternatively, you can contact Apple Technical Support.
    For more details, please refer to the Repair Pricing tab on the left.
    If Apple determines that an iPod is not repairable, for example, if it has failed due catastrophic damage or the iPod has been disassembled into multiple pieces, then Out-of-Warranty Service is not available and the iPod will be returned. Please see Apple's Repair Terms And Conditions for further details.

  • IPod Nano 6th Gen needs a restore every day...?

    My iPod Nano 6th Gen works well for arond 24 hours but every morning when i wake up it says it needs to be restored using iTuunes.
    When I restore it, it works perfectly. No problems at all. I can fill it to capacity with music and it works all day. The next morning, the battery is still really close to fully charged, but the iPod is in recovery mode. I've scoured the internet but haven't found anyone with a similar problem.
    Generally, I've read about iPods that will not restore, or that, even after a restore, will remain in recovery mode, which is indicative of moisture or some other malady.
    This Nano has been well cared for and is in flawless condition in every way aside from the condition mentioned. Not even a scratch or smudge. I'm baffled.
    Has anyone experienced a similar problem? I love to use the smaller ipod when running or bike riding, but am stuck restoring it each day I choose to use it over my Classic 160's.
    Any help is appreciated.

    Ok, here is a bit of an update on the issue.
    For the last two mornings, when the Nano says it needs a restore, I've hard reset it (holding down both the select/menu and volume down button simultaneously), then, when the apple logo shows, I held down the menu and the volume up button simultaneously, which then restores the ipod back to functioning properly (I think I read that this is supposed to put the ipod into disk mode, which it doesn't do on this Nano, obviously).
    Aside from being annoying as all get up, I suppose the ipod is working, so it's a minor victory.
    Still, does anyone know why this might be happening every single night? The battery is still completely charged and once I do the aforementioned sequence, the ipod works perfectly until the next day.

  • Sync address book & iCal in iPod nano (6th Gen)?

    hello all,
    today I switched from an ancient iPod to a brandnew iPod nano 6th Gen. To my utter surprise there seems to be no (straightforward) way to sync my address book or iCal...? Needless to say, the olden iPod offered that feature. Have I overlooked something???
    Thanks and Regards,
    Georg

    hello planb77,
    thanks for your fast reply! Unfortunately it is as feared... Of course you are right in that I could have spotted the missing functionality in the User Guide. However, nobody documents the functions they leave out -> you need a list of required functions and compare it with the available functions... :-(
    I understand that Apple wants to differentiate the nano from e.g. the touch. But leaving out such basic functions which were even present in the iPod 1G is a sure way to p*** off even the most loyal customers. I buy Apple products (at a higher price) because I want things to simply work! If I wanted problems, I would by my PCs - or my MP3-players in the dept store around the corner. Arrggghhh!!!
    Georg

Maybe you are looking for

  • Unable to access remote database object using database link

    Hi all, I have created a database link to a remote server SQL> create database link remote_link connect to lax_dba identified by lax_dba using 'abc.corp.com'; database link created when i am trying to access any table of lax_dba sql> select * from la

  • How to optimize Thunderbird for Windows 8.1 tablet

    I have installed Thunderbird on a Dell Venue Pro 11, which is an i5 based tablet using Windows 8.1. The default font sizes and other controls for Thunderbird are difficult to operate using only touch on the smaller screen. (Imagine Thunderbird runnin

  • Compilation error with (amp) restriction specifier in C++ AMP

    Hi, [double post from : original post ] I'm using C++ AMP (I'm not that experienced with C++ and I'm new to AMP, so I have to stumble through this stuff) But I thought I had this code working, but now I'm getting the following error: Error    1    er

  • OLE in forms

    Hi, I am trying to use OLE in forms to access objects. There is a function called FUNCTION GET_OLE_NUM (obj OLEOBJ, memberid PLS_INTEGER) RETURN oleprop NUMBER; Can anyone please tell me what this value memberid stands for Thanks in advance Padma

  • NOOB code question

    've got code for a geeklet to display current and forecast weather. Here's what the output looks like now: Now | Fair, 32F Tomorrow | Sunny, 32|21F I'm trying to accomplish two goals: 1. add degree symbols between the temp and the "f" 2. break "now"