I am having audio issues. I cant hear callers but I think they hear me. My keyboard isnt creating the little noise either.

I cant hear callers. I hear the phone ring. I answer and they can hear me but not I them.
the keyboard doesnt ding with each pressing of the letter either

For the Keyboard Clicks issue: Have you checked to make sure that the Keyboard Clicks options is toggled to "On" in the settings?
Settings->Sounds->Keyboard Clicks
For the Receiver problem: I would backup the device in iTunes. Then attempt a Restore, followed by setting the iPhone up as a new device. Make sure you rename your iPhone something different as to not overwrite the existing backup you made. Doing this will not bring any of your information back onto the device, but will give you the opportunity to test the device with a new operating system installed on it. If the problem persist after the restore (set up as a new device) then the problem lies in the hardware. If the problem does not persist, then you will need to avoid restore the device from your backup, as the problem lies in a corrupted operating system. Please let me know if you have any questions.
Hope this helps
- Greg

Similar Messages

  • Facetime? I have been having audio issues where by my contacts cannot hear me after a while.. why is this...?

    facetime? I have been having audio issues where by my contacts cannot hear me after a while.. why is this...?

    Don't know.  You asked in the wrong forum community.  Try next door, down the road, around the corner and through the cornfield maze - Facetime for Mac community

  • How can I recover an old/disused iCloud account. I was having some issues with my apple id so I restored my iPad, I am now stuck on the activation screen as I no longer use the iCloud account i used to set up the iPad and can't remember the address or pas

    How can I recover an old/disused iCloud account. I was having some issues with my apple id so I restored my iPad, I am now stuck on the activation screen as I no longer use the iCloud account i used to set up the iPad and can't remember the address or pas

    I have the same problem - it is maddening. I rely on this iPad for work so this is not just an annoyance! The above solutions of changing the appleid on the device or on the website do not work.
    The old email address no longer exists - I haven't used it in a year probably and I no longer have the account.  I logged into the appleid website and there is no trace of the old email address so there is nothing that can be deleted or changed there.  On the iPad there is no trace of the old email address so nothing can be deleted there either. I have updated the iPad software and the same problem comes right back.  Every 2 seconds I am asked to log in using the old non-existent email.  The device is currently useless.
    The only recent change to anything was the addition of an Apple TV device, which was set up using the correct login and password.
    Does anyone have any ideas? The iPad has been backed up to the iCloud so presumably it now won't recognize the current iCloud account? So restoring may notbe an option?

  • IMovie audio issues. Fine in timeline, but when rendering to iTunes or Media Browser, audio from certain portions of movie files are heard in places where it shouldn't be !

    iMovie 11  audio issues. Fine in timeline, but when rendering to iTunes or Media Browser, audio from certain portions of movie files are heard in places where it shouldn't be !
    I have created a project where I have a montage of photos and video clips edited together with music under. Some audio portions of the video files are being muted in some areas and those portions are being heard in another part of the project. This is not for all video clips only certain ones.
    The project plays fine in the timeline, but when I render the project thru iTunes or Media Browser, this is when the project goes corrupt.
    I tried detaching the Audio from the video clips and this somewhat worked, but the original problem still exists with certain audio still being heard where it's not supposed to be.

    I have a fix - or rather, a workaround.
    WARNING: It is lengthy, but still far better than starting a new project from scratch.
    I had this same issue and none of my transitions/clips were at custom speeds, nor did I have anything else weird going on. Unfortunately there is nothing you can do within iMovie to fix this, at least there wasn't for me. iMovie is BY FAR the buggiest software I have ever used and if you haven't already spent hours slaving away on a project, you are so much better off using just about anything else to edit your video.
    ...But let's assume you have already spent many hours working on your project and you don't want to start all over. Well then, you have at least one option.
    It's a pain in the neck, but it's infinitely better than restarting your project from scratch.
    This will require:
    A software called Soundflower (which is free) and some kind of audio editing software (I use Logic, but really any should work).
    1.) You're going to need to export your video with the messed up audio. Typically if you're audio is messing up, you're video is at least usually working just fine (at least it always does for me).
    2.) You're going to need to open that video in your audio software and import only the audio. If your software doesn't give you this option, then you're going to need to record the audio from your video using the audio software and Soundflower. You can find tutorials on how to do this, but it's honestly pretty straightforward once you start playing around with you Mac's audio I/O settings. Remember to have your computer's volume all the way up when doing this.
    3.) Watch/listen to your video and make notes of where the audio errors occur. I HIGHLY RECOMMEND writing down times too,  as they will be extremely helpful later.
    4.) Now were going to rip some working audio from the iMovie project itself. Go back into your iMovie project and only play back audio while in the edit window for this step. Do NOT play your project back in full screen.
    This part is key: if you try to play back your project from the beginning the audio will usually still mess up. So, what you're gonna have to do is go back on your edit window timeline right before these errors occur and play that specific clip back while recording this working audio with Soundflower and your audio software. Essentially we're only recording the parts of the audio where these errors occur, so try to do this in order if you can. Try to leave several seconds of audio in before the error - that way we can use it as reference when we construct our new audio track.
    5.) Now in your audio software you should have your original error-filled audio track and the new clips that we just captured. This part can be painstaking if you're not familiar with audio editing softwares, but as you'll learn, it's really not that hard.
    You're going to look at your original audio track and compare it to your new working audio clips. You should be able to notice where those new clips are supposed to go by looking at the identical (or close to identical) waveform shapes in your original audio track. The two should correspond with one another. If you don't understand what I mean right now, you will when you start playing around with the audio. This is why marking times is very important.
    Take your new clips and split them up if you haven't already, that way you can drag them around and edit them separately from one another. Essentially your going to line these new clips up with original and then replace the original parts with new ones.
    We need to get this as precise as possible, so start off by getting them as close as you can with your naked eye, and then use a zoom tool to zoom in as much as possible so that you can get them lined up PERFECTLY, or at least extremely close. In some softwares you can just drag these new clips on top of the old track, but most of the time you will need to actually cut out the old piece and replace it with the new one. In doing this, zoom in and make sure that you are NOT cutting out a bigger space than your new clip will fill - otherwise you will have small gaps in your audio.
    VERY IMPORTANT: Also make sure that this new audio track starts at the EXACT SAME time as your original - otherwise your new audio will be out of sync.
    I know this part can really suck if you're not used to audio editing, but at this point, there is little other choice.
    6.) Once you are done with this, export your newly pieced together audio track.
    7.) Now open iMovie and create a NEW project. Re-import the video that you exported earlier that has the messed up audio. This might take a while, so just be patient.
    8.) Then right click the clip and select "Detach Audio". This will do just that - allowing you to edit the audio separately from the video. Now delete this audio.
    9.) Now, import the new, perfect audio track that we just made and make sure that it starts at the start of the project. Make sure it's in sync and that everything works.
    Now just export your new video with the working audio and you should be done. Since we have given iMovie the audio with no editing actually being done in iMovie, it does not have to generate its own audio now and you should have absolutely no errors now - unless there is some that you forgot to take out earlier.
    YOU'RE FINALLY DONE!!!
    I know this entire process *****, but if you're that far into your project, there is little else that you can do. Now you've learned your lesson:
    DON'T USE IMOVIE EVER AGAIN.
    I hope this helped!

  • I am having strange issue with my apple tv...i set up pictures to scroll through to the tv using home sharing.  Now album covers are interspersed with my pictures.  I have been using apple tv for a while and never had this happen before

    I am having strange issue with my apple tv...i set up pictures to scroll through to the tv using home sharing.  Now album covers are interspersed with my pictures.  I have been using apple tv for a while and never had this happen before

    Are you watching this content though iCloud or though from iTunes on your local computer?  If it is from iCloud have you tried downloading the content to iTunes and watching it on ATV from that source to see if it still happens?  This is geerally a much more reliable way to view the content.  Easer to fast forward and rewind too.
    - I have a stable internet connection
    Clearlly you don't
    >(Ive tested on other devices)
    Which does not tell you anything about the specific connnection from ATV to iCloud.
    >I am able to stream Netflix problem free from my AppleTV without so much as a hicup
    Again which does not tell you anything about the specific connnection from ATV to iCloud.
    >- I am able to download the episodes to my phone, ipad, and computer without any issues
    Again which does not tell you anything about the specific connnection from ATV to iCloud.  It does remove your ISP throattly traffice as a possible cause though.  So that is good.
    Have you checked your wireless rounter?  Tried doing the factory restor on it?  Upgrading it's firmware?  Is it and or ATV getting extreamly hot when this problme happens?

  • I just started having an issue with my bank website working properly. They have told me it is because of the last safari upgrade. Is this being resolved?

    I just started having an issue with my bank website working properly. They have told me it is because of the last safari upgrade. Is this being resolved?

    You might want to consider "voting with your feet" and taking your business to another bank.  When they tell you the upgrade is the problem, it is really their problem and not yours.  If you don't want to do that, the suggestion that you try another browser is absolutely correct.

  • My iPhone 5 is suddenly having audio issues through the headphone jack.

    So this is a strange situation, and I'll try to explain in depth so that someone might be able to suggest a solution. As reference, I have an iPhone 5 that I purchased in late-February. I've had every other model of iPhone except for the first iPhone, so I am pretty familiar with the device. I used to be on AT&T, and switched to Verizon when I upgraded to the iPhone 5.
    Two days ago, I was on a six hour road-trip, and I'd been playing my music like normal through my car's auxillary cable. After stopping for lunch, I went to plug my music again, but once the music started to play, I realized that only the drums were playing at normal levels while the vocals were very, very soft. I switched through a few different songs, and realized that all the songs were being played at different levels; sometimes the backup vocals were normal levels while the instrumentation and lead vocals were quiet, or vice versa. I decided to plug my iPhone in to charge, and when I did this, the audio levels were all normal. However, the iPhone was NOT charging. I removed the charger, and the audio went back to being weak and distorted. I went back and forth at this for a bit, trying to figure out what was going on.
    Since then and after some testing, I realize that my iPhone will now only charge anywhere EXCEPT in the car charger (I simply use my USB cable that came with my iPhone and plug it into the power adapter I have in the car). This morning, I tested the audio in my home speaker system, and I had the same audio issues. Only half the song's tracks would be at normal audio levels, while the other half would be at a very quiet, almost nonexistent level. I tried plugging my charger into the phone to see if that'd make a difference, but instead of the audio going back to normal like it does in the car, the music stopped and there was just crackling and very noisy distortion sounds.
    I'm super confused and not sure what to do. This has never happened to me with any of my iPhones. I am updating my software right now, and am hoping that that may help somehow. Otherwise, I'm at a loss. Any suggestions as to what I should do would be greatly appreciated!

    Do the new iMacs have digital audio out through the headphone jack?
    Yes.
    http://support.apple.com/kb/SP576

  • Having audio issues with droid 2

    So I just got my droid 2 global phone today and it has no audio on the speaker, so I can't hear my volume at all when reciving calls or playing music but I CAN talk to people. I have put my head set in and it works then , I have restarted it and taken the battery out. I have no idea what else to do. HELP!!!

    You have done all the troubleshooting steps that would be suggested to fix it. I'm sorry to say, your phone needs to be exchanged. If this was an online order and you are within 30 days of purchase, you can exchange your phone in any company-owned Verizon Wireless store or call us at 800-922-0204. For phones purchases at authorized dealers, you would return to their store location. 

  • Im having audio issues on my Envy17 3270nr

    Whenever I play a video or  audio, it makes a tapping  sound.  Can I fix this?

    I called HP, and they tried to walk me through the process of finding the problem, and they came to the conclusion of it being a hardware issue. Something is wrong with the speakers. They want me to send it to them  so they can fix or replace the speakers. Maybe you can do the same.

  • Anyone having Audio Issues with new Mac Mini, new Thunderbolt Display and new Pegasus R4?

    I can't listen to the built-in speakers on my brand new Apple thunderbolt monitor to the terrible audio quality.  I'm running Mac Lion on a new Mac Mini with a brand new Promise Pegasus R4 - all purchased in January 2012.   The entire setup is connected via Thunderbust errh, I mean Thunderbolt. 

    Hi,
    I'm also having an audio problem, which I suspect now is caused by my Thunderbolt display.
    See https://discussions.apple.com/message/21499606#21499606 for the small thread.

  • I have iPhone 5 iOS 7.0.2 and my call waiting stopped working. Anyone know how to fix this ? Or also having this issue? I hear the beep when the call comes in but not ID and no option to switch calls.

    My call waiting stopped working in iPhone 5 iOS 7.0.2 ? Anyone have this issue or know how to fix it?

    I have this issue as well and it really bothers me.

  • I'm having audio issues with my hp pavilion dv9910us laptop.

    The day before yesterday the sound was working perfectly.. Yesterday I noticed I didn't have any sound so I checked under control panel- hardware and sound and tried to adjust the volume and it says "no audio device installed". Then I went to Device manager to sound, video and game controllers and checked properties and it says the device is working properly. I tried downloading sp42090.exe (an updated driver) but I can't install b/c it says it's already installed. This is so frustrating, don't know what to do. Any  help will be appreciated.

    Welcome to the forum.
    Hmm..  sp42090 appears to be the touchpad driver patch (for Vista 64bit).
    Not an audio driver.
    Here's the Vista Audio help file to get help get you started:
    http://h10025.www1.hp.com/ewfrf/wc/document?docnam​e=c00833257&cc=us&dlc=en&lc=en&product=3740565&tmp​...
    The Audio help page does have some things to try and even a "Mr. Fixit" button.  It may work - I can't test it for you, I'm running Windows 7.  Smiling.
    Here's your Software and Driver Page:
    http://h10025.www1.hp.com/ewfrf/wc/softwareCategor​y?os=2100&lc=en&cc=us&dlc=en&sw_lang=&product=3740​...
    Sounds like you've done some homework.
    It's not "disabled", is it?  Right click on the sound icon to check...
    Nevermind - "no audio output device" is not "disabled".
    If the system can find the driver in its own internal backup, it will do so when you reboot the system.  If not, then you start looking for it at the posts above.   Keep us posted - lots of smart folks here to help!
    Hope this helps!
    Kind Regards,
    Dragon-Fur

  • My audio files are mixed in STEREO but when exported they come out MONO ?

    I'm working on a music video project and have been sent AIF files that are in stereo.
    However, when they are imported into FCP, they seem to be coming out to mono. I don't do anyhing to the file other than import and synch up to the video.
    I'm not as well versed in the audio world, am I not doing something to the file or in the import process that is making it play in mono instead of stereo?
    Thanks!

    it might be just your sequence settings need changing
    select your sequenec and press Command-0 (zero)
    then switch to the Audio Outputs tab
    if the Grouping is set to Dual Mono, then you can change it to Stereo and click Ok
    see if it works

  • Bootcamp 3.1 and imac windows 7 64bit update not installing. Audio issues!

    After many days of work getting the windows 7 working in bootcamp in my imac 27 (still with audio issues) I eagerly awaited the bootcamp update and imac updates.
    Neither will install.
    Then I find that according to tech support as of now I have to reinstall Windows 7 again for the updates to work!
    It took me 5 full 8 hours days to get all my scientific programs installed and working, now I find I can't even simply update the drivers I need. I don't want to reinstall.
    My only issues are audio.
    Here they are:
    1) The headset jack works fine on the Mac side, but in Windows 7, it causes the i7 intel CPU to go crazy. There is no CPU spike on the mac side.
    2) The headset jack in the imac is a trrs jack. The same as in the iphone, a tri-band jack that has three bands, two audio out channels and one mic in channel. A trrs headset works fine on the mac side with using the headset mic (as in iphone) rather than the built in mic. (this provides much better quality for sound recording). I don't want to use a usb mike.
    In Windows 7 the mic part of the trrs headset does not work.
    3) In Windows 7 when going into audio devices recording, no audio mixer shows up, so when I do video or audio screen capture the only way to capture the sound is through the speakers and then back through the imac built in mic, rather than directly through the unit. (terrible sound quality) On the mac side the mixer element works fine.
    Now I find from other imac users that even the new updates for the imac on windows 7 don't address and fix the audio issues. I am sure not going to go through 5 more days work only to find the audio issues still don't work.
    I need these audio aspects to work properly though!
    I have tried to get drivers for the cirrus logic audio card, but guess what there are none available and cirrus logic doesn't even recognize the board or offer drivers.
    I have many windows programs I must have for my scientific research!I bought the top of the line Imac with all the bells and whistles because Apple promised that the machine could run Windows 7 in bootcamp natively!
    It doesn't. This has been a nightmare of problems.
    Is Apple going to step up to the plate and make good on their promises?
    Does any one have a fix for any of the audio issues, or know how to install the new drivers without a complete reinstall of Windows?
    Installing a few sound drivers and software should not require a complete reinstall. Getting the proper drivers for the headset jack audio in and audio out jack should be the most basic of fixes. Making the audio mixer work should be elementary.
    If you are an Apple tech person or an Apple user that can help on these issues, please do!
    Thanks, Dr. Duke
    An American profesor in Europe.
    PS I will post this under Imac windows 7 updates without a reinstall and under
    imac Sound issues.

    On another thread a few people have responded saying that their imac has the same situation, the cpu is going crazy and the imac gets hot with headphones or speakers plugged in. But this doesn't happen in the mac side.
    If you have an late 2009 imac and don't have these audio issues, let us hear from you. If you don't, lay out the problem here.
    Here is my last two cents in to the inquiry.
    Not only does the cpu run crazy but the imac 27 gets very, very hot. Since I unplugged the headphones, it runs much, much cooler.
    Certainly, some Mac engineers should take care of this problem, it seems it is universal on all the imac 27's and from what I gather, the smaller screened cousins too.
    Also, we certainly want a stereo mix option for audio in or out, or what is called "what you hear" or wave out. Imac is supposed to be much geared to multimedia apps.
    Finally, the mic jack part of the trrs set up MUST be fixed! A lot of manufacturers are going to headset combo jacks as they call them, mic in and stereo out on the same tribanded plug. But, the old single jack for mic in and single jack for stereo out are two tiny parts of the hardware and super inexpensive for the manufacturer. Why in the **** to go to the "advanced" triplug if the **** thing doesn't work.
    Mac has a great reputation. I hope they remedy these problems right away.
    Anyone whose imac 27 or 24 whose headset plug is working correctly. Let us know! I don't think anyone's is, but I think that few people understand that their cpu is running so much faster with the plug in, plus few even understand the combo jack and the triband, or trrs audio jack! Out of 4 audio technicians I talked to, not one of them knew what a trrs jack was or that you even have a mic in jack as part of the headset jack!
    When I told one senior that it worked on the Mac side, he didn't believe for a while, thought my sound might be recorded from the onboard mic, but I proved it to him by tapping iaudibly on my iphone mic headset and and it showing up in garage band clearly and listening to big difference in audio.
    As for a usb audio adapter, I am in a neon light environment and find that those adapters are more sensitive to electrical interference. Besides I want to use the headset jack as it was meant to be used!
    Thats it.
    Again, if anyone using an imac 27 and windows 7 64 or 32 doesnt have these problems, let us know! We are all anxious for a fix!
    Best to all!

  • Premiere Pro CC Audio Issue

    Having a really serious issue since upgrading to CC from CS6. The issue seems to stem from audio crossfades? First of all while in CC and editing, randomly when the playbar hits an audio crossfade a terrible noise will sound (almost blowing my speakers). Thought it was maybe speakers, so I unplugged, reset, restarted computer, re-opened project.... same issue. I updated CC and the issue seemed to go away. But now I'm trying to export a project (with a strict deadline) and this strange digital noise keeps showing up in my export! I went in and adjusted audio and tried some fixes I found online (although they were referring to CS5.5) and the noise went away, but showed up in different spots! And it's always where there is an audio crossfade.
    This is a serious issue! Please help!
    imac - 3.4GHz i7, 16gb DDR3 ram, 10.9.1, newest update on PPCC

    Tried the keyframe fades, worked for all but one section of the project, which confused me even more. It's very random and hard to figure out why it's doing what it is. SO I found an old thread for an audio issus (similar but a bit different) in CS5.5. They said there fix was to: copy audio, delete all the audio tracks, add new audio tracks, re-paste the audio. And belive it or not, it worked. I have no idea why. So for now, on this project, I'm good. But I look forward to a bug fix on this soon.
    I appreciate your help Mark.

Maybe you are looking for