Intra-Interface-Traffic fails at first try - second try works
Hi,
we are running two ASA5550 as fail-over.
Everything works fine. But there is still a little "bug".
same-security-traffic permit intra-interface
is enabled.
Now, let's open an PostgreSQL-Connection from 10.10.1.22 to 10.10.1.8 (same subnet, same interface "IT").
First try (using psql for a connection), I get
11:27:56|106015|10.10.1.22|51019|10.10.1.8|5432|Deny TCP (no connection) from 10.10.1.22/51019 to 10.10.1.8/5432 flags RST on interface IT
11:27:56|302014|10.10.1.22|51019|10.10.1.8|5432|Teardown TCP connection 290800318 for IT:10.10.1.22/51019 to IT:10.10.1.8/5432 duration 0:00:00 bytes 0 TCP Reset-O
11:27:56|302013|10.10.1.22|51019|10.10.1.8|5432|Built inbound TCP connection 290800318 for IT:10.10.1.22/51019 (10.10.1.22/51019) to IT:10.10.1.8/5432 (10.10.1.8/5432)
11:27:53|302014|10.10.1.22|51019|10.10.1.8|5432|Teardown TCP connection 290800140 for IT:10.10.1.22/51019 to IT:10.10.1.8/5432 duration 0:00:00 bytes 0 TCP Reset-O
11:27:53|302013|10.10.1.22|51019|10.10.1.8|5432|Built inbound TCP connection 290800140 for IT:10.10.1.22/51019 (10.10.1.22/51019) to IT:10.10.1.8/5432 (10.10.1.8/5432)
in the ASA log.
psql now runs into a time out.
Starting the second try, the ASA doesn't report any packets and the connection is established.
Phillip,
Based on the syslogs the reset packet is coming from another device "Reset-O". The best way to troubleshoot this issue will be applying captures on the IT interface in order to track the source MAC of the reset and to have a better picture of the traffic flow.
Luis Silva
Similar Messages
-
Microphone suddenly stopped working(the first one, second still working)
microphone suddenly stopped working(the first one, second still working)--- any ideas beside sending it in?!
Repair your phone with PCC
PC Companion (PCC)
Bridge (for Mac)
Alternatives on How to backup Xperias
http://talk.sonymobile.com/thread/36355
"I'd rather be hated for who I am, than loved for who I am not." Kurt Cobain (1967-1994) -
Suspends fails the first time, but succeeds the second time
Hi all,
I am running Arch Linux on my Dell XPS 15 9530 laptop, and overall I am very happy with the combination. I have however had some issues with suspending.
The problem is that the first time I try to suspend the machine it seems to go to sleep, but then two seconds later it automatically wakes up again. If I then immediately try again to suspend, it works (it does not wake up automatically). Does anyone know what could be going on, and how this can be fixed?
Usually I suspend from my gnome 3 desktop, but I have also tried to suspend directly using 'systemctl suspend' without having an X server running, and the result is exactly the same. I have tried a few versions of the vanilla kernel, but also the linux-lts and the linux-ck images, but to no avail.
Here is the output from dmesg, where suspend fails:
PM: Syncing filesystems ... done.
PM: Preparing system for mem sleep
bbswitch: enabling discrete graphics
Freezing user space processes ... (elapsed 0.543 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
PM: Entering mem sleep
Suspending console(s) (use no_console_suspend to debug)
sd 1:0:0:0: [sda] Synchronizing SCSI cache
smsc75xx 3-1:1.0 enp0s20u1: entering SUSPEND2 mode
sd 1:0:0:0: [sda] Stopping disk
Removing pn544
PM: suspend of devices complete after 334.544 msecs
PM: late suspend of devices complete after 0.201 msecs
ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
ehci-pci 0000:00:1a.0: System wakeup enabled by ACPI
xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
PM: noirq suspend of devices complete after 26.944 msecs
ACPI: Preparing to enter system sleep state S3
PM: Saving platform NVS memory
Disabling non-boot CPUs ...
kvm: disabling virtualization on CPU1
smpboot: CPU 1 is now offline
kvm: disabling virtualization on CPU2
smpboot: CPU 2 is now offline
kvm: disabling virtualization on CPU3
smpboot: CPU 3 is now offline
kvm: disabling virtualization on CPU4
smpboot: CPU 4 is now offline
kvm: disabling virtualization on CPU5
smpboot: CPU 5 is now offline
kvm: disabling virtualization on CPU6
smpboot: CPU 6 is now offline
kvm: disabling virtualization on CPU7
smpboot: CPU 7 is now offline
ACPI: Low-level resume complete
PM: Restoring platform NVS memory
Enabling non-boot CPUs ...
x86: Booting SMP configuration:
smpboot: Booting Node 0 Processor 1 APIC 0x2
kvm: enabling virtualization on CPU1
Intel pstate controlling: cpu 1
CPU1 is up
smpboot: Booting Node 0 Processor 2 APIC 0x4
kvm: enabling virtualization on CPU2
Intel pstate controlling: cpu 2
CPU2 is up
smpboot: Booting Node 0 Processor 3 APIC 0x6
kvm: enabling virtualization on CPU3
Intel pstate controlling: cpu 3
CPU3 is up
smpboot: Booting Node 0 Processor 4 APIC 0x1
kvm: enabling virtualization on CPU4
Intel pstate controlling: cpu 4
CPU4 is up
smpboot: Booting Node 0 Processor 5 APIC 0x3
kvm: enabling virtualization on CPU5
Intel pstate controlling: cpu 5
CPU5 is up
smpboot: Booting Node 0 Processor 6 APIC 0x5
kvm: enabling virtualization on CPU6
Intel pstate controlling: cpu 6
CPU6 is up
smpboot: Booting Node 0 Processor 7 APIC 0x7
kvm: enabling virtualization on CPU7
Intel pstate controlling: cpu 7
CPU7 is up
ACPI: Waking up from system sleep state S3
acpi LNXPOWER:01: Turning OFF
xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
ehci-pci 0000:00:1a.0: System wakeup disabled by ACPI
ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
PM: noirq resume of devices complete after 73.424 msecs
PM: early resume of devices complete after 0.091 msecs
mei_me 0000:00:16.0: irq 49 for MSI/MSI-X
snd_hda_intel 0000:00:03.0: irq 50 for MSI/MSI-X
snd_hda_intel 0000:00:1b.0: irq 53 for MSI/MSI-X
mei_me 0000:00:16.0: NFC MEI VERSION: IVN 0x1 Vendor ID 0x1 Type 0x1
Probing NFC pn544
ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata2.00: failed to get NCQ Send/Recv Log Emask 0x1
usb 3-1: reset high-speed USB device number 2 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 1.
ata2.00: failed to get NCQ Send/Recv Log Emask 0x1
ata2.00: configured for UDMA/133
sd 1:0:0:0: [sda] Starting disk
usb 3-1: reset high-speed USB device number 2 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 1.
usb 3-1: reset high-speed USB device number 2 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88007fd75180
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88007fd751c0
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88007fd75200
smsc75xx 3-1:1.0 enp0s20u1: resuming from SUSPEND2
usb 3-4: reset full-speed USB device number 3 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 2.
usb 3-4: reset full-speed USB device number 3 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 2.
usb 3-4: reset full-speed USB device number 3 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9ac0
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9a80
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9a40
usb 3-6: reset full-speed USB device number 4 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 3.
usb 3-6: reset full-speed USB device number 4 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 3.
[drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
usb 3-6: reset full-speed USB device number 4 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804174ddc80
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804174ddcc0
usb 3-11: reset high-speed USB device number 6 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 5.
usb 3-11: reset high-speed USB device number 6 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 5.
usb 3-11: reset high-speed USB device number 6 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9480
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9440
usb 3-9: reset full-speed USB device number 5 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 4.
usb 3-9: reset full-speed USB device number 5 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 4.
pciehp 0000:00:1c.0:pcie04: Link Training Error occurs
pciehp 0000:00:1c.0:pcie04: Failed to check link status
dpm_run_callback(): pnp_bus_resume+0x0/0xa0 returns -19
PM: Device 00:08 failed to resume: error -19
usb 3-9: reset full-speed USB device number 5 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804181db000
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804181db040
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804181db080
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880417451e80
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880417451ec0
PM: resume of devices complete after 2769.054 msecs
PM: Finishing wakeup.
Restarting tasks ...
iwlwifi 0000:06:00.0: no hotplug settings from platform
rtsx_pci 0000:07:00.0: no hotplug settings from platform
done.
Bluetooth: hci0: read Intel version: 370710018002030d00
Bluetooth: hci0: Intel Bluetooth firmware file: intel/ibt-hw-37.7.10-fw-1.80.2.3.d.bseq
video LNXVIDEO:00: Restoring backlight state
video LNXVIDEO:01: Restoring backlight state
bbswitch: disabling discrete graphics
ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20131218/nsarguments-95)
Bluetooth: hci0: Intel Bluetooth firmware patch completed and activated
smsc75xx 3-1:1.0 enp0s20u1: link down
smsc75xx 3-1:1.0 enp0s20u1: link down
smsc75xx 3-1:1.0 enp0s20u1: kevent 4 may have been dropped
smsc75xx 3-1:1.0 enp0s20u1: link down
smsc75xx 3-1:1.0 enp0s20u1: link down
and here where suspend succeeds:
smsc75xx 3-1:1.0 enp0s20u1: kevent 4 may have been dropped
smsc75xx 3-1:1.0 enp0s20u1: link up, 100Mbps, full-duplex, lpa 0xC5E1
smsc75xx 3-1:1.0 enp0s20u1: link up, 100Mbps, full-duplex, lpa 0xC5E1
PM: Syncing filesystems ... done.
PM: Preparing system for mem sleep
bbswitch: enabling discrete graphics
Freezing user space processes ... (elapsed 0.412 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
PM: Entering mem sleep
Suspending console(s) (use no_console_suspend to debug)
sd 1:0:0:0: [sda] Synchronizing SCSI cache
smsc75xx 3-1:1.0 enp0s20u1: entering SUSPEND2 mode
sd 1:0:0:0: [sda] Stopping disk
Removing pn544
PM: suspend of devices complete after 780.265 msecs
PM: late suspend of devices complete after 0.387 msecs
ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
ehci-pci 0000:00:1a.0: System wakeup enabled by ACPI
xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
PM: noirq suspend of devices complete after 26.988 msecs
ACPI: Preparing to enter system sleep state S3
PM: Saving platform NVS memory
Disabling non-boot CPUs ...
kvm: disabling virtualization on CPU1
smpboot: CPU 1 is now offline
kvm: disabling virtualization on CPU2
smpboot: CPU 2 is now offline
kvm: disabling virtualization on CPU3
smpboot: CPU 3 is now offline
kvm: disabling virtualization on CPU4
smpboot: CPU 4 is now offline
kvm: disabling virtualization on CPU5
smpboot: CPU 5 is now offline
kvm: disabling virtualization on CPU6
smpboot: CPU 6 is now offline
kvm: disabling virtualization on CPU7
smpboot: CPU 7 is now offline
ACPI: Low-level resume complete
PM: Restoring platform NVS memory
Enabling non-boot CPUs ...
x86: Booting SMP configuration:
smpboot: Booting Node 0 Processor 1 APIC 0x2
kvm: enabling virtualization on CPU1
Intel pstate controlling: cpu 1
CPU1 is up
smpboot: Booting Node 0 Processor 2 APIC 0x4
kvm: enabling virtualization on CPU2
Intel pstate controlling: cpu 2
CPU2 is up
smpboot: Booting Node 0 Processor 3 APIC 0x6
kvm: enabling virtualization on CPU3
Intel pstate controlling: cpu 3
CPU3 is up
smpboot: Booting Node 0 Processor 4 APIC 0x1
kvm: enabling virtualization on CPU4
Intel pstate controlling: cpu 4
CPU4 is up
smpboot: Booting Node 0 Processor 5 APIC 0x3
kvm: enabling virtualization on CPU5
Intel pstate controlling: cpu 5
CPU5 is up
smpboot: Booting Node 0 Processor 6 APIC 0x5
kvm: enabling virtualization on CPU6
Intel pstate controlling: cpu 6
CPU6 is up
smpboot: Booting Node 0 Processor 7 APIC 0x7
kvm: enabling virtualization on CPU7
Intel pstate controlling: cpu 7
CPU7 is up
ACPI: Waking up from system sleep state S3
acpi LNXPOWER:01: Turning OFF
xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
ehci-pci 0000:00:1a.0: System wakeup disabled by ACPI
ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
PM: noirq resume of devices complete after 73.411 msecs
PM: early resume of devices complete after 0.097 msecs
mei_me 0000:00:16.0: irq 49 for MSI/MSI-X
snd_hda_intel 0000:00:03.0: irq 50 for MSI/MSI-X
snd_hda_intel 0000:00:1b.0: irq 53 for MSI/MSI-X
mei_me 0000:00:16.0: NFC MEI VERSION: IVN 0x1 Vendor ID 0x1 Type 0x1
Probing NFC pn544
ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata2.00: failed to get NCQ Send/Recv Log Emask 0x1
usb 3-4: reset full-speed USB device number 3 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 2.
ata2.00: failed to get NCQ Send/Recv Log Emask 0x1
ata2.00: configured for UDMA/133
sd 1:0:0:0: [sda] Starting disk
usb 3-4: reset full-speed USB device number 3 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 2.
usb 3-4: reset full-speed USB device number 3 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9ac0
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9a80
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9a40
usb 3-1: reset high-speed USB device number 2 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 1.
usb 3-1: reset high-speed USB device number 2 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 1.
usb 3-1: reset high-speed USB device number 2 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88007fd75180
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88007fd751c0
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88007fd75200
smsc75xx 3-1:1.0 enp0s20u1: resuming from SUSPEND2
usb 3-9: reset full-speed USB device number 5 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 4.
usb 3-9: reset full-speed USB device number 5 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 4.
[drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
usb 3-9: reset full-speed USB device number 5 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804181db000
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804181db040
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804181db080
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880417451e80
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880417451ec0
usb 3-6: reset full-speed USB device number 4 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 3.
usb 3-6: reset full-speed USB device number 4 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 3.
usb 3-6: reset full-speed USB device number 4 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804174ddc80
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804174ddcc0
usb 3-11: reset high-speed USB device number 6 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 5.
usb 3-11: reset high-speed USB device number 6 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 5.
pciehp 0000:00:1c.0:pcie04: Link Training Error occurs
pciehp 0000:00:1c.0:pcie04: Failed to check link status
dpm_run_callback(): pnp_bus_resume+0x0/0xa0 returns -19
PM: Device 00:08 failed to resume: error -19
usb 3-11: reset high-speed USB device number 6 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9480
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9440
PM: resume of devices complete after 2801.389 msecs
PM: Finishing wakeup.
Restarting tasks ...
iwlwifi 0000:06:00.0: no hotplug settings from platform
rtsx_pci 0000:07:00.0: no hotplug settings from platform
done.
Bluetooth: hci0: read Intel version: 370710018002030d00
Bluetooth: hci0: Intel Bluetooth firmware file: intel/ibt-hw-37.7.10-fw-1.80.2.3.d.bseq
video LNXVIDEO:00: Restoring backlight state
video LNXVIDEO:01: Restoring backlight state
bbswitch: disabling discrete graphics
ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20131218/nsarguments-95)
Bluetooth: hci0: Intel Bluetooth firmware patch completed and activated
systemd[1]: Requested transaction contradicts existing jobs: File exists
systemd[1]: Service sleep.target is not needed anymore. Stopping.
smsc75xx 3-1:1.0 enp0s20u1: kevent 4 may have been dropped
smsc75xx 3-1:1.0 enp0s20u1: link down
smsc75xx 3-1:1.0 enp0s20u1: link down
It seems to me like the only real difference has to do with the xhci_hcd errors, perhaps the following:
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 2.
Any input or help would be highly appreciated.Rexilion wrote:Maybe you could confirm your suspicion by rmmoding xhci before suspend and modprobing it after resume?
Thanks for the response. I should have said so, but I had already tried that, but without any luck. It seems like it doesn't change anything. -
I have a T440p with Windows 7 Pro. Except on rare occasions, I am unable to log into Windows with my first swipe across the fingerprint reader. The green light is on when I do the first swipe and it immediately goes off and stays off for around 15 sesconds, during which time another swipe does nothing. Then the green light will return and a second finger swipe will log me on.
Any suggestions on fixing this would be appreciated. It's made using the fingerprint reader for login impractical, because it's faster to just go to the password screen and log in that way. Thanks.
Thinkpad T440p: i7-4800MQ | Crucial 16GB DDR3-1600, 9-9-9-24 | Samsung 840 Evo 500GB SSD | Intel 7260 Dual-Band AC Wireless | Windows 7 Pro
Thinkpad X120e
Thinkpad T61p
Solved!
Go to Solution.I do see a several second delay before the fingerprint reader green light comes on after the login screen appears, but it's no where near as long as the delay I was previously seeing between the first failed swipe and waiting for the light to come on again. The new driver is a great improvement and make the fingerprint reader work as I recall when I first purchased the T440p--though possibly a bit slower to light up after the login screen appears. It would be great to see the fingerprint reader light come on more quickly after the login screen appears, but that's a minor thing compared to the failure on the first swipe.
Thanks again for giving us the opportunity to try this driver out. So far, after a day of use and several times coming out of sleep, I haven't had any failed swipes.
Skoop wrote:
sog, some feedback on that driver:
The installer runs but doesn't give any prompt that it has finished. I was waiting for something to show, after the progress bars, but it just quits. Before I restarted, I checked the driver version and saw the new one, so I figured that was all that was going to happen. Driver is v.285, dated 1/29/15.
Restarted the PC and then put it to sleep (deep sleep mode/Intel Rapid Start). First swipe does indeed work to login thereafter.
But: It takes longer for the FP reader light to come on now. I think it's that same 15 seconds mentioned above. With the previous driver, the scanner light would come on almost right away with the login screen, but the first swipe wouldn't do anything. Once the light came on again--that period of seconds, the swipe would work.
With this new driver version, I think that what's changed is that the light simply doesn't come on until whatever is going on in the background has completed. So, in effect, getting a desktop takes the same amount of time, but with only a single swipe. --Which isn't a complaint that a login should be able to be effected more quickly with the FP scanner. Perhaps it can't. Just reporting how it works now.
journeyman, your take?
Thinkpad T440p: i7-4800MQ | Crucial 16GB DDR3-1600, 9-9-9-24 | Samsung 840 Evo 500GB SSD | Intel 7260 Dual-Band AC Wireless | Windows 7 Pro
Thinkpad X120e
Thinkpad T61p -
Photoshop elements 12 won't load up on my PC. The first time I try to load it up I get a large egg timer, which lasts about 3 seconds. The programme then closes and if I try to load it again I get the circular icon which spins for 1 second and disappears. I've tried rebooting several times but nothing happens. Please help!
Hi,
Please try resetting preferences?
On Windows: Goto %appdata%\Adobe\Elements Organizer\12.0\Organizer folder and rename the files “psa.prf” (to say psa_old.prf) and “status.dat” (to say status_old.dat).
Try launching Organizer and see if it launches fine.
Thanks
Andaleeb -
Servlet failed with ServletException occurs the first time I try to access a jsp
Can any one tell why this exception occurs the first time I try to
access a jsp. After the first time it doesn't occur. This happens only
on solaris platform.
Thanks,
Shankar.
Fri Jul 28 15:02:51 PDT 2000:<I> <ListenThread> Adding address:
192.168.0.36/192.168.0.36 to licensed client list
Fri Jul 28 15:02:51 PDT 2000:<I> <ServletContext-General> file: init
Fri Jul 28 15:02:55 PDT 2000:<I> <ServletContext-General> *.jsp: init
Fri Jul 28 15:02:55 PDT 2000:<I> <ServletContext-General> *.jsp: param
verbose initialized to: true
Fri Jul 28 15:02:55 PDT 2000:<I> <ServletContext-General> *.jsp: param
packagePrefix initialized to: jsp_servlet
Fri Jul 28 15:02:55 PDT 2000:<I> <ServletContext-General> *.jsp: param
compileCommand initialized to: /usr/bin/javac
Fri Jul 28 15:02:55 PDT 2000:<I> <ServletContext-General> *.jsp: param
srcCompiler initialized to weblogic.jspc
Fri Jul 28 15:02:55 PDT 2000:<I> <ServletContext-General> *.jsp: param
superclass initialized to null
Fri Jul 28 15:02:55 PDT 2000:<I> <ServletContext-General> *.jsp: param
workingDir initialized to: /space/shankar/weblogic/myserver/classfiles
Fri Jul 28 15:02:55 PDT 2000:<I> <ServletContext-General> *.jsp: param
pageCheckSeconds initialized to: 1
Fri Jul 28 15:02:55 PDT 2000:<I> <ServletContext-General> *.jsp:
initialization complete
Fri Jul 28 15:02:55 PDT 2000:<E> <ServletContext-General> Servlet failed
with ServletException
[AddToMap: pattern=/login.jsp class=jsp_servlet.login]
at java.lang.Throwable.fillInStackTrace(Native Method)
at java.lang.Throwable.fillInStackTrace(Compiled Code)
at java.lang.Throwable.<init>(Compiled Code)
at java.lang.Exception.<init>(Compiled Code)
at
javax.servlet.ServletException.<init>(ServletException.java:88)
at
weblogic.servlet.jsp.AddToMapException.<init>(AddToMapException.java:14)
at weblogic.servlet.JSPServlet.service(JSPServlet.java:118)
at javax.servlet.http.HttpServlet.service(Compiled Code)
at
weblogic.servlet.internal.ServletStubImpl.invokeServlet(Compiled Code)
at
weblogic.servlet.internal.ServletContextImpl.invokeServlet(Compiled
Code)
at
weblogic.servlet.internal.ServletContextImpl.invokeServlet(Compiled
Code)
at
weblogic.servlet.internal.ServletContextManager.invokeServlet(Compiled
Code)
at weblogic.socket.MuxableSocketHTTP.invokeServlet(Compiled
Code)
at weblogic.socket.MuxableSocketHTTP.execute(Compiled Code)
at weblogic.kernel.ExecuteThread.run(Compiled Code)
Fri Jul 28 15:02:55 PDT 2000:<I> <ServletContext-General> servletimages:
init
Try a different brand of discs. Try restarting your computer.
-
My 2nd generation iPod touch recognized the touchmic lapel microphone the first try. I recorded a memo. The second try it would not. Any ideas?
See:
Syncing to a "New" Computer or replacing a "crashed" Hard Drive: Apple Support Communities
The iPod backup that iTunes makes does not include synced media like apps and music. -
Can any one help? I have tried several times to import a particular cd onto i-tunes, but each time it will only load the first 9 seconds of each track.
If it was a recent purchase you could take it back to the store and return it as "not fit for purpose", then buy a digital version. If it is too late for that I suppose you could try contacting the record company but I doubt they care at this point since they have the money. Can't really go into any possible workarounds without breaching the TOU.
tt2 -
PropertyNode: Interface Information: Interface Description fails on second call
Hello all,
I´m new here and I have a problem.
As the subject already tells the property node: Interface Information: Interface Description fails on second call.
I have written a SubVI to get the virtual COM Port of a specified Device, which is connected via USB to my computer.
Therefore I use the "VISA Find Resource" VI to get a list of all active COM Ports and then use the mentioned property Node to get the device information.
I search for a specific string in this device information and if this string is found, I have my needed COM Port.
This is all working. Except for the case I start this SubVI a second time.
I always get an error from this property node saying: Error: -1073807246 in Property Node, VISA: (Hex 0xBFFF0072) The resource is valid, but VISA can not currently access it.
I don`t understand why I´m getting this error. I don`t even open the VISA Resource. I just check the name of it and make a VISA Close.
Maybe the problem is in my device?! I don`t know.
If I switch my device off and on again. My VI is again working once.
I hope someone has an idea, where this problem comes from and how to fix it.
I have the part of my SubVI, which is relevant to see the issue.
Thanks in advice
Best regards
TDO
Attachments:
FindCOMPort .vi 20 KBHi TDO,
please indicate cross posts! (Even when this was 'just' the German forum…)
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome -
Hi
Bet no one can solve this one
I have a cisco ASA and 2 877
The outside interface is connected to the internet, nothing on the inside
The 2 877 are also connected to the internet.
I have 2 VPN's that connect to the outside of the ASA.
Both tunnels are up.
But am unable to ping from one 877 to the other 877 via the VPN's.
I have intra interface enabled and sysopt connection permit-vpn
Tho I did set the vpn's up with match address statments.
I have been on this for ove a week and im starting to lose the plot.
Any help very much appricated.
Richardciscoasa# sh run
: Saved
ASA Version 8.0(3)
hostname ciscoasa
enable password xxx
names
interface GigabitEthernet0/0
nameif outside
security-level 0
ip address *.*.*.* 255.255.255.252
interface GigabitEthernet0/1
nameif HQ
security-level 0
no ip address
interface GigabitEthernet0/2
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 100
ip address 192.168.1.200 255.255.240.0
passwd xxx
ftp mode passive
same-security-traffic permit intra-interface
access-list 100 extended permit ip 10.20.30.0 255.255.255.0 10.20.40.0 255.255.255.0
access-list 100 extended permit ip any any
access-list 101 extended permit ip 10.20.40.0 255.255.255.0 10.20.30.0 255.255.255.0
access-list 101 extended permit ip any any
pager lines 24
mtu outside 1500
mtu HQ 1500
mtu management 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
route outside 0.0.0.0 0.0.0.0 195.*.*.*
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
dynamic-access-policy-record DfltAccessPolicy
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set intra esp-3des esp-sha-hmac
crypto map Labs 10 match address 100
crypto map Labs 10 set peer *.*.*.*
crypto map Labs 10 set transform-set intra
crypto map Labs 10 set security-association lifetime seconds 86400
crypto map Labs 11 match address 101
crypto map Labs 11 set peer *.*.*.*
crypto map Labs 11 set transform-set intra
crypto map Labs 11 set security-association lifetime seconds 86400
crypto map Labs interface outside
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 192.168.0.0 255.255.240.0 management
telnet timeout 5
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
tunnel-group *.*.*.* type ipsec-l2l
tunnel-group *.*.*.* ipsec-attributes
pre-shared-key *
tunnel-group 88.*.*.* type ipsec-l2l
tunnel-group 88.*.*.* ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
Cryptochecksum:xxx
: end
ciscoasa# -
Requirement to print data of first and second report of an ALV at once
Hi,
I have an interactive ALV report in which on double click of any of the record on first report, its details get displayed in second report. My requirement is to print all the data (of first and second report) at once.
Kindly tell me how can I achieve this functionality.
Regards,
Seema NahariaHi Seema,
Try with this FM 'REUSE_ALV_HIERARCHICAL_LIST_DISPLAY'.
Regards,
Sujatha B. -
Can't import full track from CD, only first few seconds
Please help. I'm at my wits' end on this.
I bought an iPod Nano yesterday. I installed iTunes on my PC. My PC runs Windows XP. I Put a CD in the CDROM. Up came a list of 20 tracks with the correct lengths (all 3 minutes or so long.)
I then tried to import them and all I got was about the first 12 - 15 seconds of each one. When they transfer to the iPod itself, each track sounds OK for the first 12 - 15 seconds, then stops.
I have tried this with several different CDs from different bands, and different publishers. I have uninstalled iTunes and reinstalled it. I have tried importing by three methods:
1) Using the big "Import from CD" button, top right.
2) Dragging and dropping the CD icon onto the Library icon.
3) Highlighting and dragging and dropping the tracks onto the library icon.
I went back to the shop and the man there demonstrated the process, and he did exactly what I do, and it worked. He suggested I should uninstall/reinstall.
I went to a different shop for a second opinion. They also said uninstall/reinstall.
I have uninstalled and reinstalled. Still I find I can only get the first 15 seconds or so of each track.
I have looked at every option on every drop down menu and can find nothing that appears relevant.
I am now banging my head against a wall in desperation.
Please help.
MikeHow frustrating, your cute little nano won't play!
OK, what options do you have checked on iTunes > Edit >prefrences > Advanced > Importing?
If you check off the option for "Use error correction when importing CDs" will it work?
Also you might try reading some posts over on the importing & burning forums, the CD experts hang out over there. They will probably want to see the results of your iTunes > Help > Run CD Diagnostics ....
http://discussions.apple.com/forum.jspa?forumID=791 -
I just downloaded a song and it only plays the first 50 seconds and then moves to the next song in the list. How can I get it to play the rest of the song?
If your country's iTunes Store allows you to redownload purchased tracks, I'd delete your current copy of the track and try redownloading a fresh one. See the following document for instructions:
Downloading past purchases from the App Store, iBookstore, and iTunes Store
Otherwise, I'd report the problem to the iTunes Store.
Log in to the Store. Click on "Account" in your Quick Links. When you're in your Account information screen, go down to Purchase History and click "See all".
Find the item that is not playing properly. If you can't see "Report a Problem" next to the item, click the "Report a problem" button. Now click the "Report a Problem" link next to the item. -
i made a video in final cut pro x. The entire thing isn't that long, however when it comes to sharing it only the very first few seconds are playe.
Thanks,
Jamiesee where the clip ends and then the timeline becomes black? when i add on an extra clip that line thing with the arrow does not move and if i try to export the video not all of it is played, just till that arrow.
-
First and second letters reversed when I type
Is anyone else finding this? When I type, quite frequently the first and second letters are reversed. It happens across programs, and only started after I installed Lion. I assumed it would be a temporary bug, but it persists, annoyingly.
What version of FireFox are you using? Try upgrading.
https://discussions.apple.com/message/15121441#15121441
Maybe you are looking for
-
I use Logic Expres 9.1.5. So, I've made 160+ apple loops of drum parts. They are all playable in the Apple Loops utility when I open them. However, for some nonsensical reason, no more than 31 of them will shop up in my loop browser when I re-index.
-
Questions on 3D picture control and STL file
Hi, I am currently working on a project in which I load an STL file to vizualise a 3D object (see attachment). I have several problems and questions. 1) I would like to execute rotations (X,Y,Z) on this 3D object. Unfortunately, Labview executes only
-
Accessing X509 certificate info
We are authenticating by using a certificate for the web server. We need to authorize users for a web service by using the CN or DN shown on the certificate. For the web services, how can I pull the CN or DN off the certificate used for a web service
-
Make flash website fit to screen
Hi! I'm having trouble width my AS3 flash site. I know there is a code that will make my website fit to any browser. but i can't find it anywhere?? Can anybody help me out here??
-
Mailto link from embedded image
Hello, I have to use a graphical signature for outgoing company emails and wish to have the graphic linked to a mailto: tag. I tried inserting the code in Mail's signature preferences, but the HTML tag shows up in the email, not a hyperlink. Can anyo