IP router error

I am trying to configure a catalyst 6509 switch with CatOS, and when I
issue the command:
set ip route 0.0.0.0 172.28.42.1/24
I get the error (Unkown Host), and never does the routing, my switch IP
is 192,168.0.1, and the ISP's gateway is 172.28.42.1.

Do you have MSFC on your Sup engine ???
You switch cannot do the IP routing. Your MSFC will do it. I would suggest to set the default route on your MSFC and it will take care of it.
However you can also set the default route on the switch and the command is the one given in previous post.
Your gateway for the switch would be the IP address of the vlan interface (on msfc) to which your switch's sc0 interface belong.
HTH,
-amit singh

Similar Messages

Error in back routing Error in communication channel

Hi Friends,
I am sending the Idoc from ECC250 to ECC150 using XI, whenever I am sending the Idoc, I got this error Error in back routing Error in communication channel in SXMB_MONI.
In IDX2 also I got this error I:000.
Please suggest me how to resolve this issue.
Regards,
Shalini Shah

Did you cross checked all the configurations are in Place.?
I understand that the idoc has been received from ECC250 ,Are able to see the payload (i.e idoc )
in SXMB_MONI ?
IS configuration steps like
Receiver determination,
Interface determination
are correct?
Rajesh

IDOC to File --- Error occurred during back-routing Error in communication

Hi All,
I am doing a IDOC to File (File Content Conversion) Scenario in which I have mentioned the field separator and end separator.. When i trigger the IDOC, i am only getting the first field value in the output. I am getting the following error
"- <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="">
<SAP:Category>XIServer</SAP:Category>
<SAP:Code area="OUTBINDING">CO_TXT_ROUTING_BACK_ERROR</SAP:Code>
<SAP:P1>,IHS_BS</SAP:P1>
<SAP:P2>,com_IHS_B07_BS,,</SAP:P2>
<SAP:P3 />
<SAP:P4 />
<SAP:AdditionalText />
<SAP:ApplicationFaultMessage namespace="" />
<SAP:Stack>Error occurred during back-routing Error in communication channel</SAP:Stack>
<SAP:Retry>M</SAP:Retry>
</SAP:Error>"
My port and receiver are mentioned in "IDXNOALE" so that I can ignore the Acknowledgments. Please help as the error still persists..
Thanks
Anju

Try this thread:
ALEAUD not coming to SAP from XI & u0093Acknowledgment not possible" in idx5

How to handle BEA-382108 error in route error handler?

Hi,
I have a proxy service with error handler at route level. when any wrong inputs are given to this proxy the Biz will generate fault with error as BEA-382108
having error message as XPATH can only be done for XML or MFL content. This is error is handled by system error handler but not by route error handler.
Can any tell me how to handle this error in route error handler...?

In route Error Handler.
Add If condition and add fn:contains($fault,"BEA-382108") in the if condition, and add your code/logic that you want to implement in case of this error in IF condiiton.
Let me know if this helps.
Regards,
Karan

Router Error Codes

Hello, I am trying to find one of my router error codes, however I can't seem to locate the manual below.
Can someone tell me how to find it?
Error code from the ICM CallRouter process. For information about a specific Router ErrorCode, refer to the Error Messages section of the *** ICM Master Help ***.
Thanks!

Barry,
This link should provide directions for looking up other codes...
http://www.cisco.com/en/US/products/sw/custcosw/ps1001/products_qanda_item09186a008024d1ef.shtml
Remember to rate helpful posts...

EA6900 Can't connect to Router error message from Linksys Smart Wifi

Hello Everyone, I am having an issue where I cannot remotely access my router. I currently have Charter as my ISP and have internet connectivity when at home. I can also access my router through Smart Wifi when on my local connection. When I try to access remotely I get the "Can't connect to the router" error message. I believe that I have enable the correct settings on my router to provide this service. Any thoughts would be greatly appreciated! Thanks in advance. Mike Carlin

Thanks for the reply. ISP: Charter CableModem: Wish I could tell you at this point, but not at home and can't remember specifics. I thought that I did the association. Is this what you are talking about?http://www.linksys.com/us/support-article?articleNum=140177

SAP router error on windows server 2008 64bit

Hi All,
I am installing sap router on windows 2008 server 64 bit.
While trying to generate certificate request it showing below error.
E:\usr\sap\saprouter\nt-x86_64>sapgenpse get_pse -v -r certreq -p local.pse "CN=
solman, OU=000XXXXXXX, OU=SAProuter, O=SAP, C=DE"
Got absolute PSE path "C:\Users\soladm\sec\local.pse".
Please enter PIN:
Please reenter PIN:
Supplied distinguished name: "CN=solman, OU=000XXXXXXX, OU=SAProuter, O=SAP, C=
DE"
Creating PSE with format v2 (default)
get_pse: Can't create PSE.
ERROR in af_create: (4352/0x1100) could not flush : "SW-PSE"
ERROR in create_PSE: (4352/0x1100) could not flush : "SW-PSE"
ERROR in modified_PSEFile: (4352/0x1100) could not flush : "SW-PSE"
ERROR in flush_PSEFile: (1283/0x0503) Can't write file : "C:\Users\soladm\sec\lo
cal.pse"
ERROR in aux_OctetString2file: (1283/0x0503) Can't write file : "C:\Users\soladm
\sec\local.pse"
I couldn't find the cryptography software specifically for windows 2008 server 64 bit ? So I downloaded the software for windows server 64 bit platform.
Do any one have idea on this...
Please reply..
Regards
Vinay

Hi,
Yes, there is no specific cryptography software for windows server 2008 and whatever u have chosen is correct.
Fom the following error message I could see where the issue arises.
Can't write file : "C:\Users\soladm\sec\local.pse"
I think you have not set the following ENV variable for the SAPRouter admin user (in your case soladm) and hence the sapgenpse tries to import the certificate in the SOLADM user's document folder.
Set the following variables for the user SOLADM and then try to import the certificate as mentioned in the [link|http://service.sap.com/saprouter-sncdoc].
SECUDIR = E:\usr\sap\saprouter
SNC_LIB = E:\usr\sap\saprouter\nt-x86_64\sapcrypto.dll
Hope this resolves ur issue.
Regards,
Varadharajan M

WRT160N Router Error message when connecting wireless

This is the advanced error report I received after diagnosing my connection. Everything I have tried to do has not solved my problem. Please Help! Thanks
Helper Class (RNWF MSM Helper Class) Event:
Wireless Diagnostic Helper Class Event
For complete information about this session see the Wireless Diagnostic Informational Event.
Helper Class: Native WiFi MSM
Initialize status: Success
Information for connection being diagnosed
Interface GUID: 0c5fedf8-83c2-45eb-a664-bc2385294b58
Interface name: Intel(R) Wireless WiFi Link 4965AGN
Interface type: Native WiFi
Profile: DaveJeremyCameronBen
SSID: DaveJeremyCameronBen
SSID length: 20
Connection mode: Infra
Security: Yes
Connect even if network is not broadcasting: No
Result of diagnosis: Problem found
Root cause:
The wireless settings for the network adapter on this computer don't match the settings of "DaveJeremyCameronBen"
The selected data rate is not correct.
Detailed root cause:
802.11 connection failed due to status code 18: Association denied due to requesting station not supporting all of the data rates in the BSSBasicRateSet parameter
Repair option:
View the wireless network adapter settings on this computer to verify they are compatible with this network
If you set up or own this network, you might be able to fix the problem by changing the settings on the wireless router or access point to be compatible with the settings on this computer. Contact the network administrator for "DaveJeremyCameronBen" or your hardware manufacturer for further assistance.
Event Verbosity:0
Solved!
Go to Solution.

I think there is a profile saved on your wireless computer.
What is the operating system on your computer ?
Delete the profile on your wireless computer. I think you are using the intel wireless adapter on that computer.
Open the Intel wireless adapter utility. There you will find the profiles saved on your computer. Delete the wireless network profile that you are trying to connect.
Now open the setup page of the wireles router. Go to the wireless tab. Check the wireless network name. Click on wireless security tab and check the wireless security settings. Make sure that you have the correct network key/password.
Now try to connect to the wireless network again.
If it is windows XP operating system then you can also connect to the wireless network using the windows wireless network utility.

Dynamic Routing error

Has anyone had any success with Dynamic Routing on SoaSuite 11.1.1.6. Either through a mediator or through a BPEL Phase activity?
This has been posted previously but I haven't seen a solution yet
The error I get is
Non Recoverable Business Fault :
Fact not found in the rule engine working memory, rule session execution failed. The rule session 210165 failed because an instance of the fact oracle.tip.mediator.rules.model.DynamicRouting could not be found in the working memory of the rule session. This is most likely a rule modeling error. The decision service interaction expects the fact instance to exist in the working memory of the rule session. Check the rule actions in rule designer and make sure that a fact of the expected type is being asserted. If the error persists, contact Oracle Support Services. 210165
The FMW Guide http://docs.oracle.com/cd/E15523_01/integration.1111/e10224/bp_two_layer_bpm.htm#CDEDBJBJ references a sample called BPELPhaseActivity but I can't find this sample
Cheers
Owen

As Hisaak mentioned, try routing option if you want to set URI dynamically. To use the dynamic route action, you need the fully qualified name of the service in Oracle Service Bus as described in http://download.oracle.com/docs/cd/E13159_01/osb/docs10gr3/userguide/modelingmessageflow.html#wp1081507
Thanks
Manoj

Routing error for HTTP to JDBC scenarion

Getting following error: please advise.
<?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
- 
- <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="">
<SAP:Category>XIServer</SAP:Category>
<SAP:Code area="OUTBINDING">CO_TXT_OUTBINDING_NOT_FOUND</SAP:Code>
<SAP:P1>-BS_POC_TEMP_Sender</SAP:P1>
<SAP:P2>-POC_DB_Temp_Receiver_Channel,http://xys.com/xi/projects/syn/n1.IM_POC_TEMP_DB</SAP:P2>
<SAP:P3 />
<SAP:P4 />
<SAP:AdditionalText />
<SAP:ApplicationFaultMessage namespace="" />
<SAP:Stack>No receiver agreement found for sender -BS_POC_TEMP_Sender to receiver -POC_DB_Temp_Receiver_Channel,http://xys.com/xi/projects/syn/n1.IM_POC_TEMP_DB</SAP:Stack>
<SAP:Retry>M</SAP:Retry>
</SAP:Error>

Hey
Check the URL you have provided the sender system for HTTP.then check if you have configured receiver agreement/receiver determination for that combination of sender and receiver
The messages which is coming in sxmb_moni is unable to find any receiver side configuration for the sender attributes( like sender party/service or sender interface name).
Thanx
Aamir

Copy Route Error

When I try to use the Copy Route function it does not work correctly. I select my source group and the previewed area is much larger than the desired source group. The copy route function appears to be selecting nearby vias that are not associated with that parts group. Has anyone seen this problem? It is very difficult to use the copy route function when you are always having to delete vias that become scattered over the board surface. Perhaps this is an issue NI needs to address in future versions.

Copy route is a complete PITA to use, I see it as a completely useless feature....
If you really want to replicate paths that are constant for what looks like some type of spectrum analyzer or equalizer filtering. I did the following:
Select the trace and via filters, disable all others......select trace area, copy > paste, the virtual outline will allow you to real time place the results and watch for any DRC errors in placement in real time, when happy release.....this pic took 12 seconds to do all 4.
Is this what you are trying to do?
Signature: Looking for a footprint, component, model? Might be here > http://ni.kittmaster.com
Attachments:
SS001.png ‏41 KB

TS3276 Email Reply routing error

I have two email accounts setup on my Mac. When my secondary account sends an email and the original recipient responds the reply routes in error to my primary account. How do I fix the reply to correctly route to the original sender? No idea why this occurs much less how to repair.

Mail/Preferences/Accounts/Account Information - try checking the use only this server box.

Routing error for LSMw

hi i am getting ths error whiled assigning materials to operations,
You cannot edit the task list object with activity type.
i am using direct input to upload routing material assignment to operation and this is my structure.
my source structure
GRP
GRPCT
OPERAT
ALTNATIVEBOM
HEAMEA
PLANT
MATER

Dear,
For component allocation to routing I will suggest you to go for BDC.
If you are using LSMW the please refer the OSS Note 736263 and Note 831465 - Component assignments to BOM
Regards,
R.Brahmankar

Routing Error - Scheduled ECO for Alternate Routing

Hi,
I'm creating routing using API ( and manually too, get same result)
Error Message Says:
ALT-2 routing for item 13662020 is pending from change notice 1475023.You must either make all changes to it through change notices or implement 1475023 first.
ALT-2 is the alternate I'm creating for item Routing 13662020 . I want to ask what is the link between ECO and Routing Alternate.
The ECO 1475023 has Alternat ALT-2 in it.
Thanks
Manu

The ECO 1475023 is trying to change the routing and you are trying to change it too.
So Oracle asks you to either implement or cancel the ECO.
The link is the change_notice field in the bom_operation_sequences table.
If you open the routing screen, change the drop down at the top from current/future to all and also uncheck the implemented box.
You will see the unimplemented changes.
Hope this answers your question,
Sandeep Gandhi

Trying to configure router error

Howdy, I am trying to set up a Airport base station router. The router shows up on airport utility no problem. But when i click on continue or manual setup i get this error "an error occurred while trying to access the apple wireless device. make sure your network connection is valid and try again". at the bottom left it says "error -6753". Anyone seen anything like this before? Since the airport shows up on utility it makes me think it's obviously working just won't let me configure it to my router.
Thanks,Jason

Please try the following:
o Temporarily connect your HP laptop directly to one of the available LAN ports on the AirPort Extreme Base Station (AEBS), and then, try accessing it with the AirPort Utility again.
o If this doesn't resolve the problem, be sure you disable either the WinXP or any third-party firewall. Certain ports are required to be open in order for the AIrPort Utility to properly communicate with the router.

Router error message "esw_mrvl_vlan_port_remove"

Dear All,
In one of our newly purchased Cisco Routers, I am getting the below error message :
esw_mrvl_vlan_port_remove : Unable to find entry for VLAN(1) dbnum(1)
esw_mrvl_vlan_port_remove : Unable to find entry for VLAN(1) dbnum(1)
000083: .Aug 21 10:00:04.782: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0/0, changed state to down
000084: .Aug 21 10:00:04.782: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
esw_mrvl_vlan_port_remove : Unable to find entry for VLAN(1) dbnum(1)
esw_mrvl_vlan_port_remove : Unable to find entry for VLAN(1) dbnum(1)
esw_mrvl_vlan_port_remove : Unable to find entry for VLAN(1) dbnum(1)
esw_mrvl_vlan_port_remove : Unable to find entry for VLAN(1) dbnum(1)
esw_mrvl_vlan_port_remove : Unable to find entry for VLAN(1) dbnum(1)
esw_mrvl_vlan_port_remove : Unable to find entry for VLAN(1) dbnum(1)
000085: .Aug 21 10:00:13.194: %LINK-3-UPDOWN: Interface FastEthernet0/0/0, changed state to up
000086: .Aug 21 10:00:14.194: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0/0, changed state to up
esw_mrvl_vlan_port_remove : Unable to find entry for VLAN(1) dbnum(1)
esw_mrvl_vlan_port_untagged : Unable to find entry for VLAN(1)
After rebooting the router, it starts working fine for some time & then same issue occurs. Logs are attached.
Please let us know the root cause for this & necessary troubleshooting steps for the same. It is installed with 4Port FE Switchport Module.
- Balbeer Singh.
(+91 9953 1963 56).

This is most likely bug CSCtx72953
Best advice: upgrade to 15.1.M5 -- should be out within a few days.
Re-defining the vlan (vlan xx name blah), save, and and reloading will fix it for some number of weeks/months until it fails again.
It's an issues with the switchport cards.

IP router error

Similar Messages

Maybe you are looking for