Is there errors with apple devices lately?

My iPad Wifi and iPhone 4 don't seem to send the notifications and emails through right away. It's weird. It did it home, it did it on vacation this weekend. Is Apple experiencing errors with their devices? If so, they should release iOS5 soon 'cause it would update their devices

Copied from the iPad User Guide for iOS 4.3 book that is available in iBooks as a free download. I highlighted and made the type bold and red that I think is pertinent to your question. The notification delay could be on the server end as well I would imagine.
Fetch New Data
This setting lets you turn Push on or off for MobileMe, Microsoft Exchange, Yahoo! Mail, and any other push accounts on iPad. Push accounts automatically deliver new information to iPad when new information appears on the server (delays may occur). To fetch or sync pushed data, iPad must have an Internet connection. Turn Push off to suspend delivery of email and other information, or to conserve battery life.
When Push is off, and with accounts that don’t support push, iPad can still check the server to see if new information is available. Use the Fetch New Data setting to determine how often data is requested. For optimal battery life, don’t fetch too frequently.

Similar Messages

Multiple issues with apple devices.

First up is my iPhone 5. The major issue with it is that it cannot text anyone no matter what. I have reset the network settings multiple times but to no avail. I have even tried iMessage but that is only a temporary fix, as it doesnt allow me to text people without an iPhone. Secondly, it fails most of the time to connect to the 2.4GHz signal coming from my router, however, the 5GHz signal is proving to have much better results, but i cannot connect to it at all times, as the 5GHz signal cannot reach my room.
The second issue is my iPad 2. This device straight up wont connect to either signal, despite not only a network reset, but many factory resets.
I have heard of other devices in my house not having a great connection, namely my mothers MacBook Pro, but this is only the case with apple devices.
I am fairly certain my iPhone is under warranty, so is it possible to get a replacement, or will the current one be fixed.
Any insight or advice is greatly appreciated.

RoyalRice wrote:
I am fairly certain my iPhone is under warranty, so is it possible to get a replacement, or will the current one be fixed.
Any insight or advice is greatly appreciated.
Did you reset the router? Is the wifi signal coming from the router? Since multiple devices are having problems connecting to your wifi, the problem might be there and not on the devices.
I would check that first. If that does not solve the problem, then take the iPhone to an Apple store or authorized service center.

Connection to wi-fi network with apple devices is highly unstable

About a year ago I bought a 1TB time capsule that I use to create a wi-fi network at home. At wi-fi network I connected with no problem my Imac and Iphone 3g up to 20 days ago. Since then the connection to network has become unstable, I can not always connected with both utilities, especially with the iPhone that any attempt to link it to network indicates "can not access the network". Without change anything, sometime We can connect to network without any problem for some hours, sometime for some minuts/seconds. I tried several times to reset the configuration of the time capsule, also with qualified personnel apple but I have not solved anything. Today the connection to wi-fi network at home with apple devices is highly unstable.

Hi,
Thanks for your reply but as mentioned in my post, I've checked if drivers needed updating and it says the latest driver is already installed and updated for this device (network adapter). I double checked through the HP Drivers & Download page and scan for updates for out of date and missing drivers and software and it seems to scan to about 17% then I'm taken to another page with a link that goes back to software & driver downloads page so I click 'next' to confirm my operating system which then shows a long list of things to download and being that I know very little about computers, I don't know what I'm meant to be downloading or not? Everything? There's a total of 31 possible downloads listed (under their respective headings).
Have just rung the store that sold us this notebook a week ago and they are going to replace it as they've said it sounds like a faulty network card. Whew. I'm still a little confused though as to which of the downloads from HP's list I'm meant to download (assuming I'll see a similar list when we get the replacement computer) so if anyone can help me out with that, I'd really appreciate it. Thanks.

Error with Apple's iTunes U Certs?

Hello:
We are running into an error with Apple's iTunes U certificates and get the following error and https is bombing out...
sun.security.provider.certpath.SunCertPathBuilderException: unable to find valid certification path to requested target
Anybody else having issues?

Yeah, I noticed the same problem. I sent Duncan the results of our curl output.
The problem is easily circumvented (if you're using curl) by using the -k option.
But I bet you knew that in Utah.

Which smart tv (SAMSUNG U46F7000 or SONY BRAVIA W8 46'') has the best communication and functionality with apple devices?

Which SMARTTV (SAMSUNG U46F7000 or SONY BRAVIA W8 46'') has a better communication and functionality with apple devices (i pad- iphone).
Since the above manufacturers do not give me a straight answer and it is very important reason for me to make a choice please advise!

Sorry but I must correct about SONY!!!
The question was for Bravia series W9 and not W8.

Does the Samsung galaxy s4 mini compatible with apple devices

Is the Samsung galaxy s4 compatible with apple devices such as iPad 2 Mac book air ?

Compatible in what respect?

HT5439 Has anyone had the Network time and date error with Apple TV when traveling?

Has anyone had the Network time and date error with Apple TV when traveling?

Jasion,
Maybe a bit beside the question, but it is always recommended here to open/save from/to own hard disk, and to copy from/to networks and removable media. You may be lucky, at least for a while, but it is better to be safe than sorry.
In addition to the (far greater) risk of file corruption, some issues are mentioned here:
http://helpx.adobe.com/illustrator/kb/illustrator-support-networks-removable-media.html

Iphone 4 randomly came up with a grey screen showing 'ios6' and then said 'connect to iTunes'. However iTunes won't pick the device up and states there is an error with the device?

My iPhone was working fine yesterday and then showed a grey screen with the message 'ios6'. When I tried to use the phone it came up with the error message 'connect to iTunes'. When I got home from work I did this, at first iTunes could not detect the device and then it suggested a system restore. Once the restore had completed I selected the language, country/region and then came back to the same error message 'connect to iTunes'. When I tried to connect the device iTunes could not detect it and stated that there was a problem with the device.
I have telephoned my network provider to request a replacement device on my insurance but they have said they cannot authorise until I have had the fault diagnosed my Apple. Only problem is there are no genius appointments free until Friday!
Any help would be massively appreciated!

We're not Apple. Se can not magically make a genius appointment available for you.

Error with Loading Device Software on 8700 AT&T phone.

Hi. I would like some help with my 8700 AT&T refurb blackberry phone. When I tried to download the device software (v4.5) to my already downloaded DTM (v4.6), it gave me an error message I did not know what to do with.
I want to synch my organizer data (calendar, contacts) from older desktop (Outlook 2002) to my new laptop (Outlook 2007, Windows 7). I am having trouble downloading the supporting device software. I keep getting an error message that reads "Error with the Application Loader. Cannot update software using this system as device is currently activated on a blackberry Enterprise Server or professional software. Contact administrator or check with service provider." I do not use Enterprise. I don't have an internet service plan for my phone as I use it only for calendar and contacts. AT&T gives the software option for AT&T 8700 in English device software as v4.1.0.175 as the only option that is supported by my current platform (2.0.0.90). Is this right?
All I really want to update my phone with the latest software that supports Outlook 2007 on my new laptop. What do I need to make that happen?
Thanks in advance.

Hi there!
Refurbs can be problematic. If a BB was ever activated on BES, then it has an IT Policy. IT Policies are not removed by the standard WIPE actions. Rather, they take additional steps to clean off the Policy.
Just to check, please go to this screen:
Homescreen > Options > Security Options > (Information) or (General Settings) or (something similar)
On that screen will be some selection boxes plus other sections (divided by horizontal lines). If, on that screen, there is any discussion about IT Policy (even if it says "Default"), then you indeed have an IT Policy on your BB. (The screen may also have a section for "Services").
If you don't have an IT Policy, then something else is going on...in which case, stop here and report back exactly what you found on that screen.
If you do have an IT Policy, then, in my view, you have two choices.
1) Since this refurb was provided to you by ATT, they did not deliver to you a "clean" device. You could take it back to them and have them clean the IT Policy off.
2) You can remove the Policy yourself. The process is 100% destructive to the data on the BB, so you'll want to be sure you've already taken a good full backup. Then use Method 3 in this KB.
As for what device OS to install, you have more choices than you indicated. See this page:
https://www.blackberry.com/Downloads/browseSoftware.do;jsessionid=0A15EC28AEC181D3F3F9C5235D9F166A.n...
Select, from the drop-down, your model (8700). The resulting screen shows that ATT is currently supporting 4.5.0.182 (MultiLanguage) for your BB model. The MultiLanguage pack will include English, so you don't have to fall all the way back to the English only version. So, you have choices. The best advice is to use the most recent version -- bug fixes, enhancements, and all of that.
What I advise, since you want to use Outlook 2007, is to use that 4.5.0.182 package for your BB and the most recent RIM desktop package (5.0.1.28). That way, you will have full compatibility for what you are looking for.
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Cisco 877 - not working with apple devices

Hello all,
I'm hoping someone can help me with a problem I have with my 877 adsl router.
A bit of background:
I have set this up as my home router to the internet, which is connected to a Linksys WRT54GL as a wireless access point.
My windows & Linux devices/laptops all work fine over this setup and connect without a problem
However, all my apple devices, phones and ipads don't fully work. I can get to google and a handful of pages, but not the store or games or facebook etc. (my daughter thinks its the end of the world - without FB and instagram)
If I take out the Cisco and put a Thompson router in, it all works fine. so I'm assuming it something with the Cisco config.
Below is the config I'm using on the router
Any pointers would be most appreciated.
ddhrouter#sh run
Building configuration...
Current configuration : 2292 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname ddhrouter
boot-start-marker
boot-end-marker
enable secret 5 mysecret
no aaa new-model
dot11 syslog
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.1.1
ip dhcp pool CISCODHCP
   network 192.168.1.0 255.255.255.0
   dns-server 212.50.160.100 213.249.130.100 8.8.8.8
   default-router 192.168.1.1
ip name-server 212.50.160.100
ip name-server 213.249.130.100
ip name-server 8.8.8.8
username cisco privilege 15 password 0 mysecret
archive
log config
hidekeys
interface ATM0
description ** adsl interface **
mtu 1452
no ip address
load-interval 30
no atm ilmi-keepalive
pvc 1/50
ubr 288
encapsulation aal5mux ppp dialer
dialer pool-member 1
dsl operating-mode auto
hold-queue 224 in
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface Vlan1
description ** local lan **
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
hold-queue 100 out
interface Dialer0
no ip address
interface Dialer10
description ** adsl dialer interface **
ip address negotiated
ip mtu 1482
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
ppp chap hostname myusername
ppp chap password 0 mypassword
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer10
no ip http server
no ip http secure-server
ip http max-connections 4
ip http timeout-policy idle 600 life 86400 requests 10000
ip nat inside source list 1 interface Dialer10 overload
ip access-list extended TerminalAccess
permit tcp host 192.168.1.0 any eq telnet
permit tcp any any eq 22
deny   tcp any any
ip access-list extended no_telnet
deny   tcp any any eq telnet
access-list 1 remark INSIDE_IF=Ethernet0
access-list 1 remark SDM_ACL Category=2
access-list 1 permit 192.0.0.0 0.255.255.255
access-list 110 permit icmp any any echo
access-list 110 permit icmp any any echo-reply
dialer-list 1 protocol ip permit
control-plane
line con 0
password password
no modem enable
line aux 0
line vty 0 4
access-class TerminalAccess in
password password
login
scheduler max-task-time 5000
end
ddhrouter#
all I'm after is a standard setup for my router. allow any out - deny any in.
Many thanks in advance.
Dave

ooo, you left your username, password, and enable in in clear text in the config you pasted, as well as not having an outside ACL applied and the VTY ACL allowing ssh from anywhere. Luckily the outside IP address isn't in the config or I'm sure someone would get ahold of your router....:) You should apply an outside access list and a firewall (I prefer CBAC firewall config for ease of use, but there is Zone based) to fix this. I assume ACL 110 was meant to be your outside ACL but it just isn't applied.
That being said Jody is likely right. PPPoE requires you to shrink your packet size (MTU/MSS) to allow room for the encapsulation that gets added to the packet. The command he supplied should fix this.
The 'ip mtu 1482' on the dialer interface may be too large as well.

CUA: SCUG - Transfer Users errors with Output Device does not exist

Greetings,
I'm currently setting up CUA on our ECC 6.0 boxes and ran into an issue when I run SCUG and try to transfer the users. We're in the process of upgrading to ECC. The target systems are upgraded copies of our current 4.7 target systems.
Currently we have CUA connecting to our DEV,TEST, PreProd, and Prod Systems.
The output devices only reside on the target systems. There are no output devices on our production CUA box.
I'm trying to setup the ECC CUA box and modeling all the settings to our current environment. Once I set the CUA setting, including the RFC's and ALE connections I ran scug and ran into the issue.
I only get the error where the Default Output Device is populated. Users with no Default Output transferred without any issues. I looked up notes in OSS and can't seem to find any on this subject.
Side note: If I remove the output device it transfers without error. Obviously this is not a solutions, I was merely testing out the scenario.
Any help would be greatly appreciated

Hi Alex,
there is just a little comment in SAP note #399917 (point 4).
As from my knowledge, the SCUM settings are not considered during SCUG. So setting
'output device' to local will not be a solution.
The standard way is to transport the ouput device information to your CUA-master system before taking over the users. (create transport in SPAD).
I have also another workaround for you gurus, but this will need to modify the standard coding for the time of taking over your users. Using this modification, only a warning message will appear and unknown printers will not be taken into CUA-master system.
Pls test this proposal carefully (coding is rather old....), this is just a suggestion !
Include LSUUCF01
FORM DEFAULTS_CHECK
Spool: Ausgabegerät
IF NOT DEFAULTSX-SPLD IS INITIAL AND
     NOT USER_DEFAULTS-SPLD IS INITIAL.
    SELECT SINGLE * FROM TSP03 WHERE PADEST = USER_DEFAULTS-SPLD.
    IF SY-SUBRC <> 0.
      PAR1 = USER_DEFAULTS-SPLD.
      CALL FUNCTION 'BALW_BAPIRETURN_GET2'
           EXPORTING
                TYPE       = 'W' "'E' "Warning instead of error
CL         = '01'
                NUMBER     = 29
                PAR1       = PAR1
          IMPORTING
               RETURN = ERRORTABLE
           EXCEPTIONS
                OTHERS     = 1.
APPEND ERRORTABLE.
    ENDIF.
ENDIF.
I strongly recommend to undo this modification after you have finished SCUG.
Good luck, b.rgds, Bernhard

802.1X EAP-PEAP with Apple devices

We have deployed a variety of wireless networks using Cisco WLC (2504, 5508 and Virtual WLCs) with (1550e, 1260, 2602 access points) and we have been unable to get apple device to successfully authenticate to corporate SSID's that use 802.1X against a Microsoft IAS server. We have spent numerous hours building different profiles with OS-X Server and other profile configuration utilities with no luck.
Apple devices authenticate just fine to corporate SSIDs if we use autonomous access points using 802.1x against the same Microsoft Radius server but continue to fail when we attempt the same through any of the WLC options referenced above.
Can anyone shed some light into this issue? It seems that radius request only show up on the IAS logs when something is entered in the "outer identity field"
Thanks in advance.
Ivan Chacon

Complete these steps to troubleshoot the configurations:
1.    Use the debug lwapp events enable command in order to check if the AP registers with the WLC.
2.    Check if the RADIUS server receives and validates the authentication request from the wireless client. Check the NAS-IP- Address, date and time in order to verify if the WLC was able to reach the Radius server.
Check the Passed Authentications and Failed Attempts reports on the Radius server in order to accomplish this.
3.    You can also use these debug commands in order to troubleshoot AAA authentication:
•    debug aaa all enable—Configures the debug of all AAA messages.
•    debug dot1x packet enable—Enables the debug of all dot1x packets.
Here is a sample output from the debug 802.1x aaa enable command:
(Cisco Controller) >debug dot1x aaa enable
4.    Monitor the logs on the WLC in order to check if the RADIUS server receives the user credentials. Click Monitor in order to check the logs from the WLC GUI. From the left-hand side menu, click Statistics and click Radius server from the list of options.
This is very important because in some cases, the RADIUS server never receives the user credentials if the RADIUS server configuration on the WLC is incorrect.
This is how the logs appear on the WLC if the RADIUS parameters are configured incorrectly:
You can use a combination of the show wlan summary command in order to recognize which of your WLANs employ RADIUS server authentication. Then you can view the show client summary command in order to see which MAC addresses (clients) are successfully authenticated on RADIUS WLANs. You can also correlate this with your Raduis attempts or failed attempts logs.
•    Verify on the controller that RADIUS server is in active state, and not on standby or disabled.
•    Use the ping command in order to check if the Radius server is reachable from the WLC.
•    Check if the RADIUS server is selected from the drop down menu of the WLAN (SSID).

WRT120N connection issues with Apple devices

my family has a plethora of devices we connect to the internet wirlessly through our relatively new WRT120N router, including a desktop, 3 laptops, 2 iPhones, 2 iPod Touches, an iPad, and a Playstation 3.
The wireless on the laptops and desktop (all are PCs) is fine, but the wireless on the Apple devices is terrible. every 5 seconds or so the signal will drop and the devices will lose the connection with the wifi. You have to go to settings and wireless to reconnect, but that will only last you another 15 seconds (if you're lucky). I have updated the firmware on the router, but it didn't do anything.
Does anybody have an idea of how to fix this problem? It's ridiculously annoying, and I have a feeling can be fixed with relative ease, especially since it's just the Apple products that are affected.
Thanks!

@ jimmypat1221,
Same here and I did some research and here’s what I found. I accessed the router settings by typing the 192.168.1.1 (http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=856544c9d38d4e7a870493667aac568b_20603.xml&pid=80&...) and I found out that the firmware is not updated, so I upgraded the firmware my self. I downloaded first the firmware (http://support.linksys.com/en-apac/support/routers/WRT120N) and saved it to my desktop screen. Going back to the router settings and I just follow this link on how to upgrade (http://kb.linksys.com/Linksys/ukp.aspx?pid=96&vw=1&articleid=4030) and it was successfully upgraded. I set my set settings on the router with channel 11 and the security was wpa2 personal. From then on I don’t have issue with any of my apple devices.

Wifi problems with Apple devices, Microsoft devices work fine on my home network?

Starting two weeks back I noticed network speeds had slowed. In the house (2) ipads, (2) iphones, smart TV, Wii, (2) laptops. I manage the wifi connections by manually turning them off or on, so at a given point only (3) devices may connect to wifi router. Performance has gone from slow to non existent. I can connect to my SSID but cannot say stream to my IPADs or Iphones.
Power down reset cable modem and router
Tried renewing lease
Reset network settings
Recreated my Wifi connection (linksys router)
As I've stated my Wifi issues are only with my Apple devices and Windows laptops and other non apple devices access my Wifi network just fine. Any ideas

Click on the info button on the right of the Wi-fi your trying to connect to. I You should see a bunch of numbers under the IP Address, Subnet Mask, Router, DNS, etc. If not try pressing the static button. Wait for a few seconds and close out of it. Go back in and it will most likely default back DHCP. If not press DHCP, type in your password and it should re-recognize your router. Also try settings, general, reset on the very bottom of the general tab, and reset your network settings. One of these two should work. Good luck.

Automatic watch tech combined with apple devices?

We have watches that never need to be manually rewinded, wouldnt it be nice to never have to charge your phone? I realized one is chemical energy and the other is motion, but is it possible to build an apple device with this kind of technology that may greatly extend battery life?

http://www.apple.com/feedback/iphone.html
Remember that is takes very little power to move the hands on a watch. Powering the iPhone screen, memory, CPU and flash drive takes a lot more power.

Is there errors with apple devices lately?

Similar Messages

Maybe you are looking for