It's got to be in BT's lines.
I became really so sick and tired of trying to improve broadband speed within my home (varying from 0.664 to 0.88 Mb/sec download, and varying from 0.487 to 0.51 Mb/sec upload) that I disconnected the phone line from the box on the outside of my house where the cable comes in, and ran a short cable directly to the modem.
Surprise, surprise 0.805 Mb/sec download, and 0.487 Mb/sec upload speeds.
This tells me that no matter what I do, I can never improve on these speeds.
My neighbour (whose overhead line connects to the same pole) tested his connection and he's got 3.4Mb/sec.download speed.
He explained that when he signed up to BT Broadband, he complained about the connection so much, a BT Engineer attended. He apparently worked on connections in the exchange, local distribution boxes and on the pole to achieve the 3.4Mb/sec.
Can anyone advise how I can get that service, because I'm getting absolutely no where?
Thanks
Steve
welcome to the BT community forum where customers help customers and only BT employees are the forum mods
in order for the forum members to help please can you post the adsl stats from your router may need to 'show detail' to get all stats (if hub enter 192.168.1.254 in your browser and navigate to adsl or use a-z, if netgear enter 192.168.0.1) and run btspeedtester (MAC users may have problems) bt speedtester and post the results .
are you connected directly via a filter to the NTE5 master or test socket or to somewhere else? Is the master the only phone socket in your home?
Have you tried the quiet line test? - dial 17070 option 2 - should hear nothing - best done with a corded phone. if cordless phone you may hear a 'dull hum' which is normal
Someone may then be able to offer help/assistance/suggestions to your problem
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.
Similar Messages
-
I have iMac 105.8 and want to upgrade to Snow Leopard, so got the disc from apple on line store and it will not install, just keeps ejecting from my desktop
You have entirely too little free space on the boot drive, for best performance it's best to have hard drives only 50% filled max and never more than 80% filled.
See Storage Drive here and reduce some space also make a seperate bootable clone backup of all your data BEFORE upgrading
Most commonly used backup methods
see here for how to find your disk space
Why is my computer slow?
If you upgrade and it doesn't go right or slows the machine down you might need to erase and install, which all your programs will have to be reinstalled from original sources and files from backup.
How to erase and install Snow Leopard 10.6
If you can't do this, then hire a local PC/Mac specialist.
Do not upgrade to 10.7 or 10.8 on that older machine, it will slow down and you will lose all your PPC based programs.
Leave the Lions for a brand new machine with a SSD drive. -
yesterday for the first time i turned on my macpro 2011 model and i got a crazy gray screen with lines all over it ,so i held down the power button and turn off then restarted and all was ok could someone help me with this,what caused this shut down. werd
Are the lines like psychedelic herringbone? If yes, I had that happen once, it was something serious, like the
Logic board. The good news is that it was fixed without any loss of data on the hard drive. Take it in to have Apple look at it ASAP. I took it to TekServe at the time, they are very nice about preserving your data and user library when possible.
Good luck and don't panic. -
HT4993 Hi I got 32 gb iphone 5 sprint line from America but using Turkey and send sms problem
Hi
I got 32 gb iphone 5 sprint line from America but using Turkey and send sms problemDid you request that Sprint unlock the phone?
If so, did they? Did you follow the process to complete the unlock by restoring as new?
Did you get the message indicating the iPhone is unlocked? -
Bootcamp - Seems there is no Support from Microsoft for Windows 8.1, once it is loaded.
I Just got off the Microsoft Technical Help line (Australia ph132058) and they refused to help me because I am running Win 8.1 in Bootcamp.
I have the latest Mac Book Pro Retina with a 1TB Solid State Hard drive running Win 8.1, beautiful machine, but its slower than my old MBP running windows 7 on a standard Drive.
The niggiling problem is that it seems to hang up for seven or 8 seconds on menial tasks........ like generating a new Folder or Note etc. Otherwise it runs reasonably well but not blindingly fast....
I wasn't aware Microsoft refused to help win 8.1 users on the Mac Platform........ shouldn't this Information be made more public...! Seems they are keen to drive potential Windows users away!!
Any suggestions on where I should go for help on this (Windows/Bootcamp in General) would be much appreciated ? ........ don't mind paying a reasonable price if the service is good......
I guess the wheel has turned and Microsoft are having a go at Apple again...?
Many thanks ....... Martin VThanks Turbostar.
I was thinking along the same lines. I installed Win 8.0 Pro and upgraded to 8.1 ........ probably a bad move.
I have bought a new 8.1 Licence but cant risk doing a complete reinstall until I have a back up machine ready. (My old MBP is getting a new hard drive) ......... so will give that a go in about a weeks time when the back up is in place. Cant risk having nothing!
When you say "Clean Install" ..... do you mean everything ..... as in Reformat the Bootcamp sector and start from scratch.?
I have a 2 TB LaCie Thunderbolt drive with my back up data on ..... is there a way to make the Reinstall process and large amount of Data transfer easy?
The reinstall is something I need to read up on. I was hoping the solution might be some kind of Tune up on the SSHD.
Good to hear you have a number of MBP's that are flying, I would be disappointed if the final quality wasnt a bit better.
..... do you have any tips on screen Res on the Retina ..... I am running Windows at 125% Zoom, but the Bluetooth, power, wireless, Date Icons etc are all still tiny ...... could really do with an alternative to the old "Advanced Appearance Settings"
cheers ..... Martin V -
ORA-00932: inconsistent datatypes: expected - got -
Hi,
I have writen PL/SQL packages for data loging through pipe lined function for better peformance.The below packages has been compiled sucessfully but during the run time it shows an error
like "ORA-00932: inconsistent datatypes: expected - got -".
CREATE OR REPLACE PACKAGE pkg_mkt_hub_load
AS
PROCEDURE sp_final_load_mkt_hub;
FUNCTION fnc_pipe_tot_lvl_idx_mon_hub
(pi_input_cur IN SYS_REFCURSOR)
RETURN tot_lvl_idx_mon_tt
PIPELINED;
END pkg_mkt_hub_load;
CREATE OR REPLACE PACKAGE BODY pkg_mkt_hub_load
AS
c_default_limit CONSTANT PLS_INTEGER:=5000;
c_created_dt CONSTANT DATE:=SYSDATE;
c_created_user CONSTANT VARCHAR2(20):='SYSTEM';
c_updated_dt CONSTANT DATE:=SYSDATE;
c_updated_user CONSTANT VARCHAR2(20):='SYSTEM';
-- to get the debug desc for updating process log table
vg_debug_log_desc mkt_process_log.debug_log_desc%TYPE;
--to get process log key
vg_process_log_ky mkt_process_log.process_log_ky%TYPE;
-- reset the all variables.
PROCEDURE sp_reset_global_variables;
PROCEDURE sp_final_lvl_idx_mon_hub;
--PROCEDURE sp_final_lvl_idx_dly_hub;
FUNCTION fnc_pipe_tot_lvl_idx_mon_hub
(pi_input_cur IN SYS_REFCURSOR)
RETURN tot_lvl_idx_mon_tt
PIPELINED
AS
vl_lvl_idx_mon_cur_data tot_lvl_idx_mon_tt;
BEGIN
LOOP
FETCH pi_input_cur BULK COLLECT INTO vl_lvl_idx_mon_cur_data LIMIT c_default_limit;
EXIT WHEN vl_lvl_idx_mon_cur_data.COUNT = 0;
FOR i IN 1 .. vl_lvl_idx_mon_cur_data.COUNT
LOOP
PIPE ROW (tot_lvl_idx_mon_ot(vl_lvl_idx_mon_cur_data(i).SSIA_INDEX_ID,
vl_lvl_idx_mon_cur_data(i).start_date,vl_lvl_idx_mon_cur_data(i).currency,
vl_lvl_idx_mon_cur_data(i).level1,vl_lvl_idx_mon_cur_data(i).type,
vl_lvl_idx_mon_cur_data(i).RETURN_MONTH,vl_lvl_idx_mon_cur_data(i).RETURN_3MONTHS,
vl_lvl_idx_mon_cur_data(i).RETURN_6MONTHS,vl_lvl_idx_mon_cur_data(i).RETURN_YTD,
vl_lvl_idx_mon_cur_data(i).RETURN_1YEAR,vl_lvl_idx_mon_cur_data(i).RETURN_3YEARS,
vl_lvl_idx_mon_cur_data(i).RETURN_5YEARS,vl_lvl_idx_mon_cur_data(i).RETURN_10YEARS,
vl_lvl_idx_mon_cur_data(i).MARKET_CAP));
END LOOP;
END LOOP;
CLOSE pi_input_cur;
RETURN;
END fnc_pipe_tot_lvl_idx_mon_hub;
PROCEDURE sp_final_lvl_idx_mon_hub
AS
BEGIN
MERGE INTO mkt_total_lvl_indx_mon_hub idxhub
USING TABLE(pkg_mkt_hub_load.fnc_pipe_tot_lvl_idx_mon_hub(CURSOR(SELECT idxmap.ssia_index_code,idxstg.start_date,idxstg.currency,idxstg.level1,idxstg.type,
idxstg.return_month,idxstg.return_3months, idxstg.return_6months, idxstg.return_ytd, idxstg.return_1year,
idxstg.return_3years, idxstg.return_5years,idxstg.return_10years,idxstg.market_cap
FROM mkt_total_lvl_indx_mon_stg idxstg,
md_vendor_index_map idxmap
WHERE idxmap.source = idxstg.source
AND idxmap.base_currency = idxstg.currency
AND idxmap.return_type = idxstg.TYPE
AND idxmap.mkt_index_id = idxstg.vendor_code
AND idxmap.monthly = 'Y'
AND idxmap.file_type = 'T'))) idxmonstg
ON (idxhub.ssia_index_id=idxmonstg.ssia_index_id)
WHEN MATCHED THEN
UPDATE set effective_date=idxmonstg.start_date,
CURRENCY=idxmonstg.currency,
INDEX_LEVEL=idxmonstg.LEVEL1,
TYPE=idxmonstg.type,
return_month=idxmonstg.return_month,
return_3months=idxmonstg.return_3months,
return_6months=idxmonstg.return_6months,
return_ytd=idxmonstg.return_ytd,
return_1year=idxmonstg.return_1year,
return_3years=idxmonstg.return_3years,
return_5years=idxmonstg.return_5years,
return_10years=idxmonstg.return_10years,
market_cap=idxmonstg.market_cap,
updated_dt=SYSDATE,
updated_user='MICHAEL'
WHEN NOT MATCHED THEN
INSERT ( ssia_index_id,
effective_date,
currency,
INDEX_LEVEL,
TYPE,
return_month,
return_3months,
return_6months,
return_ytd,
return_1year,
return_3years,
return_5years,
return_10years,
market_cap,
created_dt,
created_user)
VALUES( idxmonstg.ssia_index_id,
idxmonstg.start_date,
idxmonstg.currency,
idxmonstg.LEVEL1,
idxmonstg.type,
idxmonstg.return_month,
idxmonstg.return_3months,
idxmonstg.return_6months,
idxmonstg.return_ytd,
idxmonstg.return_1year,
idxmonstg.return_3years,
idxmonstg.return_5years,
idxmonstg.return_10years,
idxmonstg.market_cap,
SYSDATE,
'MICHAEL');
END sp_final_lvl_idx_mon_hub;
PROCEDURE sp_final_load_mkt_hub
as
BEGIN
sp_final_lvl_idx_mon_hub;
END sp_final_load_mkt_hub;
PROCEDURE Sp_reset_global_variables
AS
BEGIN
vg_debug_log_desc := NULL;
END sp_reset_global_variables;
END pkg_mkt_hub_load;
SHOW ERRORS Error:
ERROR at line 1:
ORA-00932: inconsistent datatypes: expected - got -
ORA-06512: at "GPAIHMKTDTA.PKG_MKT_HUB_LOAD", line 33
ORA-06512: at "GPAIHMKTDTA.PKG_MKT_HUB_LOAD", line 55
ORA-06512: at "GPAIHMKTDTA.PKG_MKT_HUB_LOAD", line 92
ORA-06512: at line 1
types scripts:
create or replace type tot_lvl_idx_mon_ot as object
(SSIA_INDEX_ID VARCHAR2(60),
start_date date,
CURRENCY VARCHAR2(10),
LEVEL1 NUMBER(31,11),
TYPE VARCHAR2(31) ,
RETURN_MONTH NUMBER(31,11),
RETURN_3MONTHS NUMBER(31,11),
RETURN_6MONTHS NUMBER(31,11),
RETURN_YTD NUMBER(31,11),
RETURN_1YEAR NUMBER(31,11),
RETURN_3YEARS NUMBER(31,11),
RETURN_5YEARS NUMBER(31,11),
RETURN_10YEARS NUMBER(31,11),
MARKET_CAP NUMBER(31,11));
create or replace type tot_lvl_idx_mon_tt is table of tot_lvl_idx_mon_ot;how to resolve this issue?>
could you please pointed out whether ref cursor used method correct or not?
>
The use looks correct but without your tables and DDL we can't even try to reproduce the problem.
Notice how you had to break down the process to find out the query that is causing the problem?
select *
from TABLE(pkg_mkt_hub_load.fnc_pipe_tot_lvl_idx_mon_hub(CURSOR(SELECT . . .Unfortunately, this is where you should have started when you began creating the process.
You are trying to design, implement and debug a process using code that has 3,4, 5 or more layers and objects and tables that have a dozen or more columns.
That is not the way I would recommend especially if you do not have experience with some of the pieces like object types and tables, pipelined functions and ref cursors. You are trying to deal with too many complications at the same time.
Here is how I would approach this if I were you.
1. Get the process to work first and then build on it. Start by copying and hacking up what you already have.
2. Create a very simple version of each of the pieces
3. Create an object type like 'tot_lvl_idx_mon_ot' with only one or two columns.
4. Create an object type like 'tot_lvl_idx_mon_tt' as a table of that simple object type
5. Create a pipelined function that uses the two new simple types, simply hard-codes a value for one or two rows and then pipes out the rows.
6. Use a simple query like the last one you posted to query the simple pipelined function
select *
from TABLE(pkg_mkt_hub_load.simpe_pipeline_function(CURSOR(SELECT . . .Work on that simple set of objects until you have the process defined and working.
Then expand the now working example to use get the data values dynamically and to use more complicated objects.
Start with something simple that works. Then build on it.
It will take a lot less time and will point out other issues with your approach to this. Also, if you try a simple version using the SCOTT emp or dept table and it doesn't work you can post the code and we can try to reproduce it and help find the problem. -
I turned my MacBook Pro and got an error message with lines and lines of code and then it turns off
I turned on my MacBook Pro and got an error message with several lines of code and then it turns off
Were you able to see any of the error codes? Have you tried resetting NVRAM (booting while hold cmd+option+p+r until the second chime)?
-
Dear Contacts Journal Support Team,
Each time i have been trying what you put up for me,i always delete The Application Completely,then go to iTune Apps Store to re-download it. I know the apps store will not give me an old version,that is why i do not use my Mac or iMac to replace the application however this has also been updated on my Macs.
I reiterated in my message yesterday that,it is not that what you asked me to do is not working or i did not follow your instructions into details. I did follow every steps you stated.
The end result is that, WHEN IT REACHES DATA MIGRATION,THE SCREEN WILL BE BLACK OR LIGHT BLUE BLACK,WITH A WHITE SCROLLING LINE THREAD ON THE DEVICE SCREEN,MEANING MIGRATION IS ABOUT TO TAKE PLACE. THIS WILL MOVE FOR ABOUT 2 or 3SECONDS,AND IT WILL CRASH.
I have tried this several time,i do not mind starting all over again,i just want it to work with iCloud. We can give you feedback,and i praise your effort for not getting tired to respond. This is a good and real customer service assistance of which i really appreciate.
My devices are up-to-date,and the application i download is the latest version.
Please let's makes this application work,there is non like it on The Apps Store. So you should be proud of your work and your innovation which i see as very powerful as well as extremely useful. But when it becomes unworkable it render all my eulogies to your effort meaningless.
Thanks for contacting me again and i hope you will make it work again. Please forget about my previous DATA,i want to start it NEW. But you can not turn ON & OFF even the iCloud on Contacts Journal.
Thanks a LOT.
The Reverend Canon Dr. IBITOYE.
Sent from my iPhone 5⃣ Highly reliable especially when you are on the GOOOOO!!!!! Grab one for your own use,you will never-REGRET HAVING ONE!!!!!
On 13 Feb 2013, at 07:46, Contacts Journal Support <[email protected]> wrote:
Thanks. Can you confirm this step:
- make sure all devices are updated to iOS6.1, and running the latest version of the app (3.3) [you can check if you have the latest version of the app by going to the App Store on your device, then checking the Updates section to see if you see any update for CJournal]
- Another way to check is when you open CJournal, go to More -> Contact Us -> About page -> it should show the current app version.
This is very important. If you are running the previous version of the app (3.2.1), then this crash will definitely happen on iOS6.1. You need to upgrade the CJournal app to the latest. After updating the app, you will have to follow the same steps as before, including cleaning up the iCloud database.
Regards.
On Feb 12, 2013, at 7:13 PM, ADEBAYO ADETOYE ALABA IBITOYE <[email protected]> wrote:
Dear Sir / Madame,
Thanks for your lengthy information which is highly and diligently consummated and extremely digested.
All what you indicated in your last mail,i have done it and all efforts is TO NO AVAIL.
1. It does clean all the devices but at the start of MIGRATION,the application crashes away and off. This has happened at least more than 5 to 7 times on one device. I have got main 2 iPhone 5 main lines,the other lines are subsidiary to my European lines and Dublin. So,i do not on or try to set them at the same time.
2. Please,kindly see it in this way,look at the year you have released this application,i have not made or bombard you with this kind of problems.
3. I am an old man,i love the progress of our younger ones in Technology. It is just a shame i was not born to the computer and application age,it pains me. Because i know i embrace and love Technology,even at this old age. So i can not do anything to destroy your work,i will rather support you for progress so my up spring will also progress in all their discipline. Also remember my vocation as a priest,my position is to encourage,correct and not to destroy another persons efforts and labour.
Above all,i just finished trying it twice now,at the migration point,it crashes out in few seconds when it comes with that line of migration.
The time in London now is 03:10 in the morning,this is what i suffer on this application: SLEEPLESS NIGHTS.
If there is any other one like this out their that can take files,journals,documents,ToDo's like this one. Please let me know,i do not mind how much it will cost me. I just want it to work.
Thanks and look forward to your response.
Regards,
The Reverend Canon Dr. IBITOYE.
Sent from my iPhone 5⃣ Highly reliable especially when you are on the GOOOOO!!!!! Grab one for your own use,you will never-REGRET HAVING ONE!!!!!
On 13 Feb 2013, at 01:00, Contacts Journal Support <[email protected]> wrote:
Thanks. We just sent you an email an hour before you sent this one!! It had instructions on how to overcome this particular problem "Cannot sync since another device is syncing at the same time". It doesn't look like you followed those instructions at all.
This is our detailed feedback, so please read and follow them closely::
- you can only get this message when you are trying to sync to iCloud with CJournal. It means that something else got stuck while syncing with iCloud before, and it needs you to clean up the iCloud database for CJournal (as previously instructed, and repeated below)
- there is no hope for us to recover your previous data. The best we can do is to get the app working again with iCloud, by cleaning up your iCloud data for CJournal
- your old data was previously wiped out when you cleaned up the iCloud database without backing it up. There isn't any chance that we can recover that. Maybe the Apple iCloud engineers can restore that for you (though I doubt it). If they do, then let us know and we can figure something out.
Meanwhile, follow these instructions for resetting your iCloud data:
- make sure all devices are updated to iOS6.1, and running the latest version of the app (3.3) [you can check if you have the latest version of the app by going to the App Store on your device, then checking the Updates section to see if you see any update for CJournal]
- make sure to turn off iCloud sync option in CJournal, on all devices
- To clean out your iCloud database, you have to go to the Settings app -> iCloud -> Storage and Backup -> Manage Storage -> Documents and Data -> Show All -> look for Contacts Journal. (if you don’t see it, then look for “icloud” with a blank white icon). Here, press the Edit button, then the Delete All button. This will clean out your iCloud database. Note that it will take a few minutes for your data to be deleted from your other devices, and you shouldn’t try syncing any of your devices to iCloud in the meantime.
- Now restart all your devices by powering them down, then power them back up again.
- Now, wait 5-10 minutes for the delete to go through
- On one of your devices, with the latest data, turn on iCloud. If it gives an initial message saying "iCloud data already exists", then press Cancel. It means it hasn't updated from iCloud that you deleted the data. You'll have to open the Settings app and go to the same Show All page again, just so the device tries to connect to iCloud again. Wait a few minutes before trying to enable iCloud again.
- After it's done transferring the information to iCloud, wait a few minutes, then connect your 2nd device to iCloud and let it connect with the existing iCloud data. If it gives a message saying "First Time iCloud Sync", then press Cancel. It means it hasn't detected the data you just uploaded from iCloud yet. Try again in a minute.
Please follow these instructions closely. Let me know any instruction isn't clear to you.
Regards.
On Feb 12, 2013, at 3:57 PM, ADEBAYO ADETOYE ALABA IBITOYE <[email protected]> wrote:
Dear Contacts Journal Support,
I am so disappointed as you have not deem it right to make a follow up enquiry about my problems of which you were aware about all my Troubles.
I keep you inform of all my efforts with apple iCloud Department and what i was told.
I did not delete any of my files from Contacts Journal from my iCloud Account as one of my iPhone 4S still contains a 75% of some of my data. This device has been switched off since. Any attempt i made to use iCloud on contact journal always comes up with a message i have related to you in my former message that: Contacts Journal encounter a SYNC problems from iCloud and that 2 devices can not be Sync at the same time; while all other devices are actually switched off.
I am sending this Note now as the time limit given to me by iCloud Team will expire tomorrow. As i have said,this application has beautiful features but to make it work and Sync with either iCloud or Dropbox is a problems.
I mean,about 8 devices can not have these problems at a go while other applications link with either iCloud or Dropbox are working on all these Devices. I can list all these for you if require as apple iCloud Team do check this as well.
The iCloud restoration you sent me does not work,but i think this has teach me a great lesson as not to rely fully on an application like this anymore. I count my loss,my time and STRESS,i can not but let you know how i feel and my pains,frustrations and disappointments on this application.
I have been using this application since it has been introduced,i know all the ups and downs,but not like this.
I hereby appeal to you to sort out this PROBLEMS: "PROBLEM WITH iCloud SYNC: can not sync since another device is syncing at the same time: please wait and try again."
The iCloud button will not even switched on.
I look forward to hear from you.
Regards,
The Reverend Canon Dr. IBITOYE.
Sent from my iPhone 5⃣ Highly reliable especially when you are on the GOOOOO!!!!! Grab one for your own use,you will never-REGRET HAVING ONE!!!!!
On 12 Feb 2013, at 22:00, Contacts Journal Support <[email protected]> wrote:
You can also go through the iCloud reset process again. That should get everything back in order again with iCloud. But there is no way to restore your old data unfortunately, since the Delete All wiped it out.
Instructions for resetting your iCloud data:
- make sure all devices are updated to iOS6.1, and running the latest version of the app (3.3)
- turn off iCloud sync option in CJournal is it is enabled on any device
- To clean out your iCloud database, you have to go to the Settings app -> iCloud -> Storage and Backup -> Manage Storage -> Documents and Data -> Show All -> look for Contacts Journal. (if you don’t see it, then look for “icloud” with a blank white icon). Here, press the Edit button, then the Delete All button. This will clean out your iCloud database. Note that it will take a few minutes for your data to be deleted from your other devices, and you shouldn’t try syncing any of your devices to iCloud in the meantime.
- Now restart all your devices by powering them down, then power them back up again.
- On your device with the latest data, turn on iCloud. If it gives an initial message saying "iCloud data already exists", then press Cancel. It means it hasn't updated from iCloud that you deleted the data. You'll have to open the Settings app and go to the same Show All page again, just so the device tries to connect to iCloud again. Wait a few minutes before trying to enable iCloud again.
- After it's done transferring the information to iCloud, wait a few minutes, then connect your 2nd device to iCloud and let it connect with the existing iCloud data. If it gives a message saying "First Time iCloud Sync", then press Cancel. It means it hasn't detected the data you just uploaded from iCloud yet. Try again in a minute.
Hope this helps.
Regards.
On Feb 7, 2013, at 7:19 PM, Contacts Journal Support <[email protected]> wrote:
Hi,
Regardless of what Apple technicians say, the simple fact is this:
- you went and did Delete All for your iCloud data ... now all your iCloud data is gone. There's no way to bring it back. We certainly don't have the power to bring it back; maybe Apple technicians do. Have you asked them about this?
- your only hope is to restore your device using an iCloud backup, from before you did the Delete All. That might restore your data to a previous state. We sent you this link again: http://apple.stackexchange.com/a/75394/11236
If the Apple technicians can help you through this process, that would be even better.
There is honestly nothing we can do at this point. There's no bug to fix. The problem is you did a Delete All of your iCloud data, without making a backup first. If you had a backup of your data, we could be able to help you, but that data is nowhere right now.
Regards.
On Feb 6, 2013, at 10:23 AM, ADEBAYO ADETOYE ALABA IBITOYE <[email protected]> wrote:
No, not at all,The apple Technicians did run series of Test on both my account and The Application. It was conclusive that the application is not communicating both with devices as well as iCloud Proactively,this is one of The Application i personally rated 5 Stars and both iPad and The iPhone ones i have never made any complaint.
I gain nothing from spoiling another persons Job and effort. But when something needs to be repair,i think it need to. It crashes on my 4 iPads and all my iPhone series.
Please apple has the conclusion,you are the one who can fix it. Apparently my screen was shared because they can see through all my efforts since last Night.
I am very DISAPPOINTED... For now i am looking towards your end to get it fix. Apple policy still remains on Third Party's Application.
Looking forward to hear from you.
Many Thanks,
Dr. IBITOYE.
Sent from my iPhone 5⃣ Highly reliable especially when you are on the GOOOOO!!!!! Grab one for your own use,you will never-REGRET HAVING ONE!!!!!
On 6 Feb 2013, at 15:58, Contacts Journal Support <[email protected]> wrote:
Thanks for the update. We would love to fix the problem for you. Unfortunately, since you deleted all the iCloud data without creating a backup first, there's not much we can do from our end. I wish we had some control over this. The best option really is to look for your iCloud backups, and try to restore your data to your iCloud backup. Did you discuss this with the iCloud technicians from Apple? I'm sure nothing was wrong with their iCloud system per se, but did they focus on recovering your data (after you explained the problem to them in detail)?
At the moment, the only hope we have is to restore one of your devices from an older iCloud backup. You probably want to do this in the next day or so, otherwise it might get lost. This might have been something that I was hoping an Apple technician would be able to walk you through.
Hope this helps.
Regards.
On Feb 6, 2013, at 5:13 AM, ADEBAYO ADETOYE ALABA IBITOYE <[email protected]> wrote:
Hello There,
i have just finished or apple has just finished with me now,and i was opportune to be attended to by one of apple most senior iCloud Engineer or Technician. We were on this problems for couples of hours,apparently they could detect all my logins through out the night on this application. It was concluded that nothing is wrong with my iCloud account neither with iCloud in general as all my other applications is working fine.
What this implies now is that they i.e. apple engineers refer me back to you as the developer of this application. The application is not communicating with device as well as to have a good Synchronisation with iCloud.
They asked me to inform you that i have suffered as an elderly man through out the night and up till now nothing can be done from their end. They want you to look into the application and that it will be monitor from their end for the next couples of Days as if i or others will get all their Documents stored in the iCloud.
The Senior Technicians might get inn contact with you if there is NO remedy to this gruelling and gruesome situation that this application has put and expose me to since 17:00 Hour yesterday evening.
I will hereby advocate for an improvement and utmost adjustment to this BEAUTIFUL APPLICATION. I know it can be made to work without any stress and PLEASE DO IT.
MANY THANKS,
The Reverend Canon Dr. IBITOYE.
Sent from my iPad4⃣Highly reliable especially when you are on the GOOOOO!!!!! Grab one for your own use,you will never-REGRET HAVING ONE!!!!!
On 6 Feb 2013, at 08:23, Contacts Journal Support <[email protected]> wrote:
Hi,
At this point, I don't think Time Machine backups would help. The only thing that might be possible is if you are backing up your iPhone or iPad to iCloud. You can check this in the Settings app -> iCloud -> Storage and Backup -> is iCloud Backup turned On? It will also show you the Last Backup under the "Backup Now" button.
If this is on, you can try to restore one of your devices to this backup version. You can follow these instructions: http://apple.stackexchange.com/a/75394/11236
You might also want to consult an Apple Genius bar if you have an Apple store close-by or if it's convenient for you to do this over the phone.
Hope this helps. Really hope you can recover this data.
Regards.
On Feb 5, 2013, at 9:07 PM, ADEBAYO ADETOYE ALABA IBITOYE <[email protected]> wrote:
Hello,
Many Thanks,
apparently i do use i cloud Sync on all my devices,but,i went to the FAQ where it says i should delete the cloud,this is the source of my Problems,apparently i would have contacted you earlier than this as it seems the latest update has been bugged,but i still manage to use it though. As soon as i delete the grey cloud,i lost everything on all my devices,all my 4 iPads,all my iPhones,my last result now is you,i can even taste any sleep as i need this file BADLY.. My last result is if you can put me through either on my Time Machine if that will still be intact. I have browse to see how i can get this work from any source. PLEASE KINDLY HELP...
My Regards,
The Reverend Canon Dr. IBITOYE.
Sent from my iPad4⃣Highly reliable especially when you are on the GOOOOO!!!!! Grab one for your own use,you will never-REGRET HAVING ONE!!!!!
On 6 Feb 2013, at 03:38, Contacts Journal Support <[email protected]> wrote:
Hi,
Thanks for your email. Were you using iCloud sync? When did you upload these missing documents? Do you use multiple devices ... if so, which device did you use to upload the documents? Did you use the "Transfer over WiFi" method, or did you use "Open In" from a different app?
Let us know and we can see if there's any way we can help.
Regards.
On Feb 5, 2013, at 5:14 PM, ADEBAYO ADETOYE ALABA IBITOYE <[email protected]> wrote:
Dear Contacts Journal Support Team,
I am sending this mail to let you know that i have been encountering
serious problems on my CONTACTS JOURNAL FILES for the past 6 to 7
Hours.
I have read all the procedure on The FAQ as well as deleting this
application on all my devices also i tried to go to Manage my Data as
well as resetting everything stated on the FAQ. But all my efforts is
to NO AVAIL. I can get all my ToDo's and other Logs. But on my Files
Section where i some important Documents and folders,it is just coming
up as loading,and if click any of the files,it will either says ERROR
or THIS FILE IS EMPTY.
Contacts Journal is a very good tools for me,but,i must confess that
as at this Time 01:05 London Time in England,i have been on this
problems since 17:30 Tuesday the 5th of February 2013. I need to pull
out a paper i have saved in This Journal to give a Lecture This
Morning.
Please i do not want to loose all my files as i have got vital and
private documents stored and saved on this Application.
I will be delighted if there is a way of retreating or getting this
Documents back as they are very vital to me.
Looking forward to hear from you in earnest.
My Regards,
The Reverend Canon Dr. ADEBAYO ADETOYE ALABA IBITOYE.
St. Alfege Church,
Church of England,
Anglican Communion,
Greater London,
England,UK.adetoye50 wrote:
Dear Contacts Journal Support Team,
FYI, this is a user to user support forum. You are NOT addressing Apple here.
Honestly, I doubt anyone is really going to take the time to read the novel you have written. -
Macbook will not boot up after running Software Update (Couldn't fix it)
Hi there,
I also have been experiencing some problems after running Software Update (Security update + Java) a couple of days ago. Similarly to Jandaf (http://discussions.apple.com/thread.jspa?messageID=9000023) I have only the gray start up screen + Apple logo + gear wheel constantly rotating. Based on the information provided in this forum I have tried some procedures which didn't solved my problem so far. Below I describe I have tried:
1) I have booted using the installation DVD and run the disk utility. When performing the First Aid/Verify Disk I found some errors ('Invalid node structure'). But I couldn't fix the problem using disk repair (same problem 'Invalid node structure' 'Volume check failed'.
2) I also tried to boot in single user mode (command + s) to run fsck -fy. It didn't work. I got the following message (last 4 lines):
CSRHIDTTransitionDriver::probe: -s
CSRHIDTTransitionDriver::probe: booting in single user .. do not match
Extension "com.apple.driver.AppleUSBTCKeyboard" has no kernel dependency.
Extension "com.apple.driver.AppleUSBTCEventDriver" has no kernel dependency.
3) When trying to boot in safe mode. I got a grey screen with the following message:
'You need to restart your computer. Hold down the power button for several seconds or press the Restart button".
4) I also tried to 'Archieve & Instal'. Again no success. After reading the DVD the action is terminated because some errors (does not specify).
5) I also tried the 'German Medicine' (http://discussions.apple.com/message.jspa?messageID=8728797#8728797) (i.e. Connect the 'problematic MacBook' to my old G4 via firewire and reinstall the 2009-001 update). Again no success. The G4 cannot mount the MacBook hardrive.
I don't know what to do any more.
A) Can I resuscitate my old system? If yes how?
B) If not, can I at least save the data I have in my old HD?
C) Is it possible to format and reinstall the OS or is this this computer doomed?
Apologies for writing so many questions but I'm really freaking out!
Thank you.
B.Hi BDAqua,
I did as you said and got a firewire backup drive (Seagate - FreeAgent Desk 500GB). I tried to make a carbon copy of HD but it seems that the copy had some problems. Below I report both the CCC and console logs:
1) "Cloning method: Backup everything
Delete items on target that aren't on the source: No
18:23:39 Enabling ownership on the target volume...
18:23:50 The target volume has ownership enabled.
18:23:50 The target volume has Access Control Lists enabled.
18:23:50 Authenticating...
18:23:50 Initiating synchronization engine...
18:23:51 Cloning...
18:31:20 rsync: readdir("/Applications/Utilities/Audio MIDI Setup.app/Contents/Resources/French.lproj"): Input/output error (5)
19:04:41 rsync: readdir("/System/Library/Components/AudioCodecs.component/Contents/Resources/Fr ench.lproj"): Input/output error (5)
19:05:41 rsync: readdir("/System/Library/CoreServices/Menu Extras/IrDA.menu/Contents/Resources/French.lproj"): Input/output error (5)
19:06:01 rsync: readdir("/System/Library/CoreServices/Menu Extras/User.menu/Contents/Resources/French.lproj"): Input/output error (5)
19:07:05 rsync: readdir("/System/Library/Extensions/IOUSBFamily.kext/Contents/PlugIns/AppleUSBC DCECMData.kext/Contents/Resources/French.lproj"): Input/output error (5)
19:10:13 rsync: readdir("/System/Library/PrivateFrameworks/Assistant.framework/Versions/A/Resou rces/French.lproj"): Input/output error (5)
19:50:10 rsync error: some files/attrs were not transferred (see previous errors) (code 23) at /Volumes/Home/Users/bombich/Development/Bombich_Software/rsync-3.0.5pre2/main.c (1047) [sender=3.0.5pre2] (51)
19:50:11 rsync: Some errors were encountered during the backup., Error code: 51
19:50:14 Sync Engine warnings: (
"rsync: readdir(\"/Applications/Utilities/Audio MIDI Setup.app/Contents/Resources/French.lproj\"): Input/output error (5)",
"rsync: readdir(\"/System/Library/Components/AudioCodecs.component/Contents/Resources/F rench.lproj\"): Input/output error (5)",
"rsync: readdir(\"/System/Library/CoreServices/Menu Extras/IrDA.menu/Contents/Resources/French.lproj\"): Input/output error (5)",
"rsync: readdir(\"/System/Library/CoreServices/Menu Extras/User.menu/Contents/Resources/French.lproj\"): Input/output error (5)",
"rsync: readdir(\"/System/Library/Extensions/IOUSBFamily.kext/Contents/PlugIns/AppleUSB CDCECMData.kext/Contents/Resources/French.lproj\"): Input/output error (5)",
"rsync: readdir(\"/System/Library/PrivateFrameworks/Assistant.framework/Versions/A/Reso urces/French.lproj\"): Input/output error (5)",
"rsync error: some files/attrs were not transferred (see previous errors) (code 23) at /Volumes/Home/Users/bombich/Development/Bombich_Software/rsync-3.0.5pre2/main.c (1047) [sender=3.0.5pre2]"
2) "Mac OS X Version 10.4.11 (Build 8S2167)
2009-03-01 10:30:14 +0100
2009-03-01 10:30:21.962 SystemUIServer[213] lang is:en
Mar 1 11:20:32 Bs-Home-Mac /usr/sbin/ocspd: starting
Mar 1 11:38:25 Bs-Home-Mac ntpd[191]: sendto(17.72.255.12): Bad file descriptor
Mar 1 12:46:40 Bs-Home-Mac ntpd[191]: sendto(17.72.255.12): Bad file descriptor
Mar 1 13:54:55 Bs-Home-Mac ntpd[191]: sendto(17.72.255.12): Bad file descriptor
Mar 1 15:03:13 Bs-Home-Mac ntpd[191]: sendto(17.72.255.12): Bad file descriptor
Mar 1 16:11:31 Bs-Home-Mac ntpd[191]: sendto(17.72.255.12): Bad file descriptor
Mar 1 17:19:46 Bs-Home-Mac ntpd[191]: sendto(17.72.255.12): Bad file descriptor
Main starting
2009-03-01 17:47:20.393 Skype[313] SkypeApplication::init called
2009-03-01 17:47:21.554 Skype[313] SKInitDebugLogging
2009-03-01 17:47:46.169 Skype[313] SkypeSound::setAudioDeviceUID: cannot find audio device with UID (null), trying to use default system output device instead
2009-03-01 17:47:47.208 Skype[313] SkypeSound::setAudioDeviceUID: cannot find audio device with UID (null), trying to use default system output device instead
Starting the process...
2009-03-01 17:48:36.186 Skype[313] MacVideo getDimensions rc == NO, width 0, height 0
2009-03-01 17:48:36.367 Skype[313] MacVideo getDimensions rc == NO, width 0, height 0
2009-03-01 17:48:37.367 Skype[313] MacVideo getDimensions rc == NO, width 0, height 0
2009-03-01 17:48:37.369 Skype[313] MacVideo getDimensions rc == NO, width 0, height 0
2009-03-01 17:59:16.450 Skype[313] SkypeSound::setAudioDeviceUID: cannot find audio device with UID (null), trying to use default system output device instead
Mar 1 17:59:19 Bs-Home-Mac crashdump[355]: Skype crashed
Mar 1 17:59:20 Bs-Home-Mac crashdump[355]: crash report written to: /Users/bernardolima/Library/Logs/CrashReporter/Skype.crash.log
Mar 1 18:23:50 Bs-Home-Mac authexec: executing /Applications/Carbon Copy Cloner.app/Contents/Resources/helper_tool
Mar 1 18:28:01 Bs-Home-Mac ntpd[191]: sendto(17.72.255.12): Bad file descriptor
Main starting
2009-03-01 18:41:03.154 Skype[393] SkypeApplication::init called
2009-03-01 18:41:12.433 Skype[393] SKInitDebugLogging
Mar 1 19:36:16 Bs-Home-Mac ntpd[191]: sendto(17.72.255.12): Bad file descriptor
Mar 1 19:55:54 Bs-Home-Mac mdimportserver[480]: -[ABAddressBook sharedAddressBook] Can't ABACQUIREFILELOCK Framework/AddressBook/ABAddressBook.m:2746
Mar 1 19:57:12 Bs-Home-Mac mdimportserver[480]: * +[NSUnarchiver unarchiveObjectWithData:]: extra data discarded
Mar 1 19:57:12 Bs-Home-Mac mdimportserver[480]: * +[NSUnarchiver unarchiveObjectWithData:]: extra data discarded
Mar 1 20:44:34 Bs-Home-Mac ntpd[191]: sendto(17.72.255.12): Bad file descriptor
Mar 1 21:52:51 Bs-Home-Mac ntpd[191]: sendto(17.72.255.12): Bad file descriptor
Mar 1 23:01:07 Bs-Home-Mac ntpd[191]: sendto(17.72.255.12): Bad file descriptor"
Due to my lack of knowledge I can't judge how bad this is. But I can tell you that every time I read the word bad in the log it scares the s*** out me. -
New to BT, Speed and Stability Issues
Hiya,
I've been on BT Unlimited Broadband for just over 2 weeks now. I have a few problems, it seems:
1. Gigabit port just doesn't seem to work. I've searched this one and I do have a HH3 Type A. It works on the occasional restart, but then stops...
2. I keep ending up with absolutely unusable speed. I've had speedtest results as low as 0.69 to 0.07 mbps (at this point the BT one won't even work as it's too slow). As soon as I reset my HH everything goes back to 'normal' at 10-12mbps. This happens once a day on weekends (I'm at home more though) and maybe every couple days during the week.
3. I'm just generally finding the broadband 'flakey'. High pings, latency in gaming, sudden lag... I'm not convinced my stats look great and my profile seems to be dropping (at best it was over 16mb, I've seen it down to 10). Unfortunately I had to reset my router earlier today as the Internet wasn't usable, at that point I'd had about 23 hours of connectivity (not a manual reset) and my HEC and CRC numbers were up to about 15 million... Here's my stats after an hour and a half. Does this look normal or a cause for concern? I've not got a telephone to do a line test, but I'll see if I can get one in the next day or so if need be.
ADSL Line Status
Connection Information
Line state:
Connected
Connection time:
0 days, 01:34:59
Downstream:
12.81 Mbps
Upstream:
1.129 Mbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.5 Annex A
Latency type:
Fast
Noise margin (Down/Up):
6.8 dB / 5.7 dB
Line attenuation (Down/Up):
25.0 dB / 13.3 dB
Output power (Down/Up):
20.7 dBm / 12.5 dBm
FEC Events (Down/Up):
0 / 0
CRC Events (Down/Up):
246712 / 32
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
344959 / 7
Error Seconds (Local/Remote):
5455 / 0
To my knowledge I have only a master socket in this flat where the router is connected via a new filter (though it's an old style socket with a BT logo top-left and a solid one-piece faceplace). I've checked wired and wireless, etc with same results.
Any thoughts or advice would be greatly appreciated.
Solved!
Go to Solution.Thank you for your advice. I did the line test with a corded phone and it seemed OK. No loud crackling or anything, maybe a bit of a faint hum, but nothing noteworthy. It dawned on me that I hadn't tried swapping out the filter and having done that the speed has gone up and the errors have gone down.
BT have also agreed to swap out my HomeHub for a Type B to fix the Gigabit issue.
Could I ask, what do you think of these results now? The other thing is... it's switched to Interleaved mode from Fast I noticed. Are there any consequences or anything I need to do since it seems I spent my whole first 10 days using a duff filter? Will it have any lasting effects on my profile/speed?
Thank you very much for your assistance.
ADSL Line Status
Connection Information
Line state:
Connected
Connection time:
0 days, 03:29:24
Downstream:
16.25 Mbps
Upstream:
1.094 Mbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.5 Annex A
Latency type:
Interleaved
Noise margin (Down/Up):
5.8 dB / 5.5 dB
Line attenuation (Down/Up):
25.0 dB / 13.3 dB
Output power (Down/Up):
20.1 dBm / 12.3 dBm
FEC Events (Down/Up):
979597 / 13
CRC Events (Down/Up):
576 / 35
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
11482 / 7
Error Seconds (Local/Remote):
314 / 3 -
External Display not working with MacBook Pro 13" (early 2011)
I just bought the current MacBook Pro 13" (i7 processor). My external display (Benq 20"W, 1600x1050) always says "No Signal Detected!". I've tried it with a DVI-Adapter (Griffin Video Display Converter) and with a VGA-Adapter (LMP Mini DisplayPort-VGA-Adapter). With lower resolution I once got a picture (but with weird lines). On my old MacBook (white, 2.16 Ghz) there was never a problem with this display (also OS X 10.6.6). Who can help?
Check this post if you want more info:
http://discussions.apple.com/thread.jspa?threadID=2774718
The gist is that DVI is currently very iffy through Thunderbolt. Mini display -> mini display OR mini display -> HDMI should work fine. It's most likely not your adapter itself but the fact that it's DVI.
If you can, get a mini display -> HDMI adapter and try that (assuming your external has HDMI).
I should hear back tomorrow or Monday from apple engineers with more specific info about this issue and I will update then.
BTW- DVI anywhere in the chain will make things fail. Mini Display -> DVI and a DVI/HDMI cable won't work with any reliability (I've tested it on three completely different monitors). -
My Macbook Pro Won't boot. Unable to find the driver for this platform
Hi there,
After doing some casual internet browsing earlier today (facebook + twitter etc) my laptop froze up. While I was able to click between windows, the ever faithful beach ball was there to ensure I couldn't really do anything, including making the dock appear when mousing towards the bottom. So I held down the power button to shut it down, and restarted. After the apple logo had sat there for quite some time I got a message something along the lines of:
Unable to find driver for this platform:\"ACPI\".In"@/SourceCache/xnu/xnu-1699.32.7/iokit/kernel
This was followed by a message telling me I needed to restart my computer using the power button. After several attempts all producing the same results, I was still in the same boat. So I sought some online help which lead me to boot into my recovery partition (holding down the option key at startup) and install the operating system again from there. However this is when I really started to panic. After selecting the recoverey partition the apple logo flipped between a no access symbol (that circle with a line through it) and the apple logo for a couple of seconds, before settling on the apple logo. But the recovery partition never loads and after some time I either get a symbol of a folder with a question mark in it or I similar message telling me to restart.
Next I tried plugging in my external hard drive with a few time machine backups as well as a carbon copy back up and another recovery partition. Using the external HD's recovery partition took me to a menu which the online help had initially promised where I could reinstall osx as well as use disc utitlity. So I tried to run the installer from here only to find my hard drive didn't show up in the list of destination volumes. The time machine and recovery partitions from my hard drives did, but I couldn't select these.
I then turned my attention to the disc utility and tried to repair my hard drive. I was unsure which one to select at first because there were two names for my hard drive; the first being the hard drives actual name (a samsung something or other) and the second was called 'Lion.' I started by repairing the samsung one and this was over in a few seconds saying it was successfully repaired. So I moved on to 'Lion' and this took a few moments, before stalling on a section saying "Updating boot support partitions for the volume as required." I was also advised to recover any data I could and restore I backup.
So that's where I'm currently at. I'd really hate to lose any recent data, as my last time machine back up was about a week ago and I'd made some substantial progress on a mix since then!
I'd really appreciate any help that anyone can offer,
Cheers!Just had another look in the disc utility and found that the samsung's partition scheme is set to master boot record, which is apprently used for windows partitions? I've no idea how this happend because When I originally formatted the drive I'm sure I would have set it to GUID partition table. Clicking on 'Lion' just gives dashes for the partition type, capacity and available space values.
-
Manual Bank Statement Posting problem
Hi,
I am posting MBS(ff67) for the openitem clearance in openitem managed check deposit bankaccount and a counter entry in mainbank account.after i posted a session is created.now when i process this session it dint execute properly.There is an error saying
"With deferred taxes use you can't use both normal bank and open bank a/c"
My company code is in IN.
can anyone please explain me what it is and how to overcome this error.
Edited by: priyanka.potla on Dec 16, 2010 9:30 PM@Ravi &Rahul
I did process the session in foreground now I didnot come across the error"with deferred tax use you cannot use bank acct or bank clear account"......but this is what happened in foreground
For session in foreground
step1:
outgoing payment with clearing(fb05)
(pk 50 account: Mainbank account)
(press enter)
step2:
Post with clearing add G/L Account item
(account: Mainbank account ,account assignment :business area is assigned)
(press enter)
step3:
post with clearing Select Open Items
(Accout: CheckIssue account)
(press enter)
Step4:
Post with clearing Enter Selection criteria
Batch Input session
Field Lowerlimit Upperlimit -
>these are the details in this screen
BELNR *
(After this when I pressed enter I got a warning)
warning:No appropriate line item is contained in this document
(but in ff67 in bankreference field I gave the checkno that is to be cleared in check issue account)
(Then I pressed enter and again a warning)
warning:No open items were found
(pressed enter again which took me to the next screen)
step5:
Post with clearing Select Open Items
message:No batch input data for screen SAPMF05A0710
(Pressed enter again)
step6:
Post with Clearing Process open items
message:no batch input data for screen SAPDF05X3100
(I CANNOT MOVE FORWARD FROM THIS SCREEN)
I WENT BACK TO CHECK MY CONFIG FOR MY POSTING RULE
I am using interpretation algorithm 011 for this posting rule in "create and asssign business transaction step " -
Converted Crystal Report Not Executing in Info View
We are in the process of testing BOXI3.1 sp2 fix pack 2.8. The problem we are having was not occurring in BOXI rel2.
After saving a Crystal Report developed with version 11.5.0.313 using CR2008, the report was run successfully within Crystal Reports. I'm assumming that the report was converted to 2008 format due to saving the report.
The report was then saved into the repository from Crystal Reports. After logging into Info View the report was scheduled. The report that normally returns results in less than 5 seconds from Crystal just hung in Info View. After 4 hours the the task was cancelled. Even though Info View presented that the report was "running", there ws NO thread started with the database. This was confirmed by our DBA
The report was rewritten from scratch using CR2008. This report was able to execute to import this report
to Info View without error.
John
Edited by: JOHN DOMBROWSKI on Jul 6, 2010 11:18 AMThanks for your response.
Before I read your response, I tried tweaking my reports and was able to resolve the issue.
Steps taken to solve the issue are the following:
a. Value not showing one field of four (4) reports.
Solution: I created new ones and integrate it in VB 6. The values are now showing. Tweaked on the line object properties, got a problem with the extended line but solved it by adjusting the height of the detail section.
b. Value not showing in sub-report.
Solution: My report used a shared variable so I can pass the condition to my sub-report. I used the new reports and just pass a query during runtime. The values in the subreport is still not showing. I added a formula and called the value in it. Values in the subreport is now showing.
I'll try to update the crystal reports version as suggested at a later time. -
Crystal reports 11: Values displayed in crystal report not showing in VB6
Hi!
I updated an existing lower version of crystal report 7 to crystal report 11. Changes are the following:
1. sql query in VB6 to add fields
2. sql query in crystal report to manipulate values and not use formula. crx11 doesn't allow summary/total in formula fields.
3. report orientation
4. additional fields to view
5. font sizes, length, can grow properties, etc.
When I tested it directly in crx 11, all fields/values are displaying correctly. When I integrated it in VB 6 using Crystal ActiveX Report Viewer Library 11.0 and CR Viewer object, the field is blank.
I've tried several checking like field suppressions, conditional suppressions, etc.
By the way, I also have a report using a subrepot with conditional suppressions. Same thing is happening. The subreport data only displays the alloted space but does not show values in VB6.
Thank you in advance for your help.
Edited by: Naga01 on Jun 28, 2011 8:46 AMThanks for your response.
Before I read your response, I tried tweaking my reports and was able to resolve the issue.
Steps taken to solve the issue are the following:
a. Value not showing one field of four (4) reports.
Solution: I created new ones and integrate it in VB 6. The values are now showing. Tweaked on the line object properties, got a problem with the extended line but solved it by adjusting the height of the detail section.
b. Value not showing in sub-report.
Solution: My report used a shared variable so I can pass the condition to my sub-report. I used the new reports and just pass a query during runtime. The values in the subreport is still not showing. I added a formula and called the value in it. Values in the subreport is now showing.
I'll try to update the crystal reports version as suggested at a later time.
Maybe you are looking for
-
Any ideas on how to get this old game working on the newer model computer? The message I get is that it wont run it "because Classic environment is no longer supported".
-
I WANT TO UPDATE MY IPOD 4.2.1 3g TO 4.3.3 . HOW DO I DO THAT?
I WANT TO UPDATE MY IPOD 4.2.1 3g TO 4.3.3 . HOW DO I DO THAT?
-
After Effects cs5 crash on launch with NO error...
[snipped crash log]
-
New version of itunes won't open on my macbook
I have just downloaded the new version of itunes and now it won't open on my macbook. Any suggestions?
-
Error installing SCCM 2012 client on server
Hi Guys, I am trying to install the SCCM 2012 client on a machine in my domain. The account specified in client settings is indeed a local admin on this server, but I get the error below: Any assistance much appreciated!