K7t Pro 6330

I want to put on a MSI K7T PRO an AMD thrton 2000+. If Would I update my mb with the last bios version, may my pc work? (i'm sorry for some error but i'm Italian)
P.S: Speak simple so i understand you

It appears the highest CPU that board will accept is a 1.2 Athlon Thunderbird.
K7T Pro CPU Support See here.

Similar Messages

K7T PRO (6330) wasted?!

Can anyone help me out?
Today I bought an Athlon Thunderbird 1333MHz 133FSB for my old K7T-pro(bios v3.2) not knowing wether it would work or not.
At first the computer booted, but showed 1000MHz, I changed the CPU Host/PCI clock graduatly until my computer just stopped booting.
And here's the problem: After repeatedly switching the CMOS clear jumper, removed the battery(few minutes), switched to the old CPU(Duron 600), the system still won't boot. Some fans and leds works, but thats it.
Diagnostic LED status: X( X( X( X(
which should indicate CPU malfunction.
(I've reset the bios before succesfully for other reasons)
Have my overoptimistic CPU change wasted the motherboard, or are there other ways to reset it or whatever?

http://www.msi.com.tw/program/support/cpu_support/cpu/spt_cpu_detail.php?UID=97%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20&NAME=MS-6330
one step beyond
try cmos and pull battery as well

Were is the temp sensor on a k7t pro MS-6330

i have a k7t pro MS-6330 and would like to know were to "system" or "case" temp sensor is as i wana make sure it is not reading falesly (hiden behind a ribon cable etc (may be the msi H/G coul help)
cos i needed to know the anserw
( i've looked for it but dont even know what to look for ? )
please help someone!

An Athlon XP could run in your board but it would only run at about 75% of it's clock speed due to the fact your board doesn't support 266MHz FSB.
Officially you should only use a Duron1300 or old Athlon 1400/200 if you could still find one.
A 250w PSU could limit you depending on the rest of your hardware and the exact model/ratings of this PSU.

CPU help MSI K7T Pro ms 6330

will a AMD MOBILE ATHLON 4 1.2GHZ 200FSB AHM1200AQQ3B work on this board msi k7t pro ms 6330 ver 2.1

i dout it ,but to say no for sure you will have to try
its certainley not one msi ever tested in it

Problem with K7T Pro (MS-6330)

I've been used MSI K7T Pro (MS-6330) for 2 years and it worked just fine. But recently the problem occurred. After I've upgraded CPU from Duron 600 to TB 1.2 GHz, when I run a heavy-loaded application such as 3DMark, 3D games (UT2003) my computer will stop working (IMO: my case just like the classic K7T Pro) but when I touched the SC1155 chip, it just warm (it won't burn my finger). So I'm confused that is my mobo defected or not?
Oh, almost forgot .. my mobo was modified and can adjust multiplier.
FYI:
I've tried underclock CPU to 950 MHz and I've found that 950 work fine (or at least it use very long time to run full-loaded and then die). Once I forgot to plugged electric-cable for my heatsink fan and temp goes 66-68C and still working normally (not running 3D app.)
So, can anyone suggest me what is the problem with my mobo?
Thank you very much and apologize for my language :P
My Spec:
AMD Athlon (TB) 1.2 GHz (but now run @950MHz) VCore 1.55 (tried 1.55-1.85 result is the same)
MSI K7T Pro (MS-6330) modified to adjust multiplier
250W Powersupply
256 MB PC133
Winfast GF2MX 32 MB
SB Live! Value
Lite-on DVD16x
2 Harddisk (40GB and 4 GB)

Hi,
RMA the board, contact your nearest MSI office and ask for the RMA department.
There is not much more you can do.

Req: K7T Pro MS-6330 and CPU

Pls, I have MSI K7T Pro motherboard. In support page there is written that this MB supports Duron up to 1.1 GHz and Thunderbird Athlon up to 1.2 GHz (100 FSB) with a little older BIOS 314 . Is the info true and recent or are there any news on it and it supports at least Duron 1.2 GHz or higher CPU ?

I have the MS-6330 v5.0 board Running an XP1900+ CPU (1.56GHz). The more recent BIOS images allow for higher CPU speeds, but it is important to check the version # of you board to verify the version of the BIOS falsh it can handle. With the v5.0 boards you can use BIOS v3.6 which allows 2200+ CPU's

K7T Pro (MS-6330)

I have a k7t pro and I want to get an athlon xp 1500+ in it. I know its not going to use the full potential of the processor but it is cheaper than an amd athlon 1.2 tbird.
I was running an amd x 1800+ on it before because i got it in a pulled system for free. it worked fine but will a 1500+ work stabily?

Dear Assaf !
'Since the K7T Pro only supports 200MHz FSB an AXP 1500+ (1333MHz) will only run at 1000MHz.'
This is true if you don't modify the processor.
On the other hand if you unlock the processor (paint the L1-bridges), paint/cut the L10 bridges and change the multiplier, then you can run the CPU at it's full speed.
I am currently running a XP1800+ (1533MHz) on a K7T Pro2 board with 102MHz FSB and a mult. of 16 (8 in BIOS +8 by CPU) at 1.63 GHz.
Regards,
/ErnyH

Msi k7t pro MS 6330 - best graphic card

hello gentlemen
As announce subject I am k7t pro ver1 owner. Nowadays the MB is provided with riva tnt2 model 64 - yeah it is old one. I would like to change the graphic card, up to the good one. So is there any graphic card you know may be recommend? Some VGA x4, having best technical parameters to the mainboard?
Kongo

thanks for reply
sure, I do not intend play newest games, anyway I wish to play hitmanII, or III and IGI-2 - some ! The MB I have is retired. Max CPU to the MB is 1.2G Athlon - and I fited out with it (1.2 Athlon). Power suply is powerful 350W of good make; also 448 sdr sdram is going to be. I just do not know if Geforce 4 will be suported by the MB. AGP port is 4x only.
Man, did I well anderstand you? You mean that if I plug in 8x graphic card the system wil be stable? Ex. MSI GForce 4 Titanium 4200 128DDR? And will work fine on the MB?
Anyway I wish to plug in as good as possible (or something about) graphic card... so are there any suggestion ?
Kongo

K7T Pro won't start up

I have a K7T pro (MS-6300) the last time I turned it off of the screen turned black but everything else kept running. No matter what I did it wouldn't turn off. I unplugged it plugged it back in and it would power itself back on and still have the same symptoms. The diagnostic led's currently all are lit red. I have pulled the batt and jumped it to discharge it and after that the only change is that when you plug it in it doesn't automatically power up but when pushing the power button it is still locked up I Unplugged everything, ie. drives, video card and modem nothing helps. It is acting like the bios won't initialize. I also put another cpu in the motherboard and still have the same problem. Can anyone help?

Interesting - sounds exactly like my problem below:
"K7T Pro 1.0 (6330) not waking up (?)"
It's like the computer comes instantly on (no startup sequence), but then there's no video and no response to kbd.
Il'll repeat my story here:
---------- 8To my delight, I discovered this morning that my K7T Pro 1.0 Linux server does not respond in any way even if it seems to be on.
I have this strange gut feeling that it's in suspend or standby mode, and refuses to wake up. Other theories are:
* partly broken PSU or
* some weird static electricity build-up and damage (2 months uptime, pwr outlet not grounded).
I 'm stuck: Any help or hints are welcome!
Story this far:
I went to check the situation: even if the computer is on (power light lit, fans spinning), there's no video, and Ctr-Alt-Del does not work.
I turned it off (pressed pwr button 4-5 secs), disconnected the KMV switch box, connected VGA and kbd cables directly to the PC and turned it on again.
Looks promising: power light turns on, fans (cpu + psu) start to spin.
Disappointment: no video, HD does not spin up, no POST beeps to be heard.
After the power is turned on the 4 diagnostic leds light up red and stay that way - no blinking. I recall this is the normal situation when the computer has booted and is running (The manual states that they all should be green after the boot, however. Should the leds be all red or all green?).
Last try: I cleared the CMOS (jumpered JBAT1 to 2-3). No effect whatsoever.

K7t pro 2a Memory prob

System setup:
K7T-Pro 2-a MS 6330 (not the Turbo)
Duron 950
768MB PC133 SDRAM
Geforce 32mb
Machine was running perfectly. Then I bought a new 512 mb stick of RAM. Installed it and the machine ran fine. I had 2x512mb of pc133 and 1x128mb pc133.Then it just rebooted on me as i was surfin the net. I got an error that said BIOS not fully ACPI compliant. THis happened about 3 times then I took the new ram out and set my machine up the way it was before. Now the machine cannot get past the windows starting up screen. It just keeps rebooting. It posts a blue screen with an error in the upper left side but I cant read it as the error disappears too fast. I have tried to push pause but to no avail. I have tried to set the ram to pc100, messed with other BIOS settings, etc but nothing is working. I dont understand why when i have taken the new ram out and have the computer set as it was before it will not work. I have read the trouble shooting guide and the MSI FAQ but nothing has worked. Any help with this matter will be greatly appreciated.

If you're usnig Windows 95/98/ME, you need to set the vcache a big amount so the memory left for Win9x is below 512MB. Try http://support.microsoft.com for more info.

K7T Pro 2-A damaging CPUs

I have the most strange problem ever.
My MSI K7T Pro 2-A is damaging the CPUs I install for some unknown reason. The mobo has been rock stable for more than a year and a half and I think it is of excellent quality. About 15 days ago the PC froze while downloading a file under Win XP Pro, and then I had to shutdown. When I turned it on again, it makes 1 beep like everything was normal but the video signal was lost. Later, after many tries with different hardware I discovered that my Athlon 1 Ghz was burned; the strange thing is that doesn't had any external signs of burning, the surface was perfect. It was installed with a very good cooler (TITAN TTC-MT1AB) so temperature problems where discarded. Then I bought a new Duron 1.1 Ghz and installed it without problems. The BIOS installed was version 3.41. I flashed succesfully the same day I installed the new CPU to the BIOS last version (3.5) and it ran succesfully for about a week. Today, same story, the Duron was gone this time. My friend told me that maybe there is a sort of incompatibility with the new BIOS, but I refuse to believe it. Apparently the PSU is fine and I see no signs of a damaged capacitor or something like that in the mobo. We have absolutely no clue of what may be causing this; My technician friend tried to boot a Duron 700 Mhz and posted OK, but the new Duron don't posted anymore, after installing it on an older KT7 Pro 2, so I guess is damaged too. Any suggestion will be apreciated, as we try to isolate this problem. I will see if we use a electronic tester. If the PSU is the culprit, I don't understand how it doesn't burned the motherboard already, and if it is the mobo, I don't understand how a processor is running very stable for a week and then dyes. Any advice? I don't want to burn another CPU. ;(

Hi,
The motherboard isn't frieing CPU's, I'm pretty sure the old CPU is fine too....
RMA the board to MSI, as it happens on some boards and they need to be repaired.
Contact your dealer or your nearest MSI Quarters on what to do.
MSI warrants the board for 2 years, so that shouldn't be a problem.

K7T Pro 266 (Ver. 1.0) with a XP 2200+ Processor

I tried using a amd xp 2200+ processor with a k7t pro 266 mainboard, as soon as i installed the 2200 processor, all i got was red lights (=Something is wrong with the processor). So I took the 2200+ out and installed a 1400+, which was working fine up to then.
Still, the 4 red lights remained.
Since then, I have tried everything. Resetting the CMOS, taking everthing off my mainboard except the processor, then except processor and ram. I even bought a new Processor!
Still: 4 red lights.
I have no Idea what to do and i don not want to buy a new mainboard.
Please help me
Greetings, Mike

Check if there's anything stuck inside the socket and also look for bent pins on the CPU.
Check for bad caps too.

K7T Pro and GeForce2 Ultra

I Probably haven't searched enough but I would like to know what you think. I purchased a GeForce2 Ultra 64mg for cheap. With the age of my board I would think it would work. The fan fires up but I have no output from the card. Is it a voltage issue? I remember something about this.
800mhz T-Bird
K7T Pro ver1:0
128mg Ram
TNT Riva 16mg
100mg (2 drives)
250 watt sparkle psu

Voltages are right on. I changed first display to agp but my little tnt card is agp and all works fine. Drivers aren't the issue as when I fire it up my monitor stays in standby. The other thing that happens is I get 4 red leds on my board. I thought that was cpu related. I get no trouble beeps. I'm going to take it to a local shop to test today. I'll post results. Thanks
800mhz T-Bird
K7T Pro ver1:0
128mg Ram
TNT Riva 16mg
100gig (2 drives)
250 watt sparkle psu

Windows 2000 (SP3) crashes on K7T Pro

Hi
I have a this configuration:
K7T Pro (BIOS 3.6)
Athlon 1200
256 Ram pc 133
Geforce 3 ti200 detonator 40.71
hdd 20gb maxtor
Windows 2000 with SP3
directx 8.1
4in1 drivers
the problem is windows hangs and the 4 back leds turn all green on any application and more specially on games like quake 3, i want to know if its caused by some drivers? or do i need to install a patch for windows 2000 that fixes some AMD issues or mobo problems?
help would be apreciated

Sure you can Install a lv application manually. just copy the exe-file,
support files in a folder. For the runtimeengine just copy the file
lvrte.dll in the folder of your application or in the windows system folder.
Hope that helps, Niko
BB Herman wrote:
> Why will a stand alone executalbe with an installer work on windows
> 2000 and crashes on windows xp professional?
>
> When I run the setup.exe file on a Windows 2000 system it installs
> properly, but the same file run on a XP Professional system I get an
> error stating Fatal Error: Installation ended prematurely because of
> an error.
>
> See
> HREF="http://exchange.ni.com/servlet/ProcessRequest?RHIVEID=101&RPAGEID=135&HOID=50650000000800000...
for more information on the specific installer I'm trying to
> use.
>
> In fact I get this error for any stand alone executable I try to
> install on any XP machines. I am using LV 7.1. Is there a way to
> manually install everything?
>
> Thanks

Msi k7t pro auto re(boot)

hi , ive got a msi k7 t pro and sometimes when i am gaming then my pc shuts down , and while it is booting 4 dleds , then i have to wait sometime before i can boot again , or reset cmos , it is mostely when i play halflife for some time , or after 20 seconds of warcraft 3 ,
specs :
amd 1400
geforce 2 pro
msi k7t pro ms6330
256 kingston , 128 samsung sdram
creative soundblaster live
cpu temp 45
case temp 30
in the summer the reboots are the most :(

See this topic:
http://www.msi.com.tw/program/service/forum/index.php?threadid=75&boardid=13&page=1
You probably have the same problem.. I have it too :(
Good luck,
Faachman

K7t Pro 6330

Similar Messages

Maybe you are looking for