LaserJet M551N Toner Issue

I have a LaserJet M551N that no longer works. Rather than hassle with getting it fixed I ordered a new one.
The toner levels in the four cartridges my non-functioning M551N are between 10% and 40%. I don't want to throw them away because toner is expensive. What I want to do is remove the full cartridges from the new M551N and store them, then transfer the old toner cartridges from my non-functioning M551N into the new one. My thought is to do this before I ever power on my new M551N. Is there any problem with this? If there's no problem in doing this, is there anything special I should do to store the unused toner cartridges until I need them?

Hi Kurisu,
I can help a bit. The M551 cartridges come with an Orange protective cover over the OPC (green roller that you should never touch). I don't know if they have a toner dam, since they are an OPC facing up configuration. Not stuff you have to know. I just don't know if the new cartridges came in the machine or separate. If separate, there is no problem, store in cool dry place until needed, usually good for many years.
Take the cartrides out of the older machine and slide them into the correct color slot in the new machine and they should work fine.
If the new carts are in the new machine, you can store them in a covered box, like one that reams of paper come in. Again, try not to touch the green roller on the top. They should be protected from light. If they came in the machine, there will be no protective orange covers.
Hope this helps and is not too late. I just got word of your message.
Dovid
Note - I work in Laser Jet Printing at HP ((;-)
The opinions expressed here are my own and not those of HP. Kudos are appreciated if I have helped you.

Similar Messages

2.1 Update did not fix SMS tone issue

I have been having the text tone issue as many others have. That problem being that when a text is recieved the phone will only vibrate. The 2.1 update did not fix the issue...imagine that.

Hi. You're the first person who has posted about the phone only vibrating when getting text messages. Can you tell me more of the problems you are experiencing when receiving texts? I ask because I exchanged my phone twice already because after a certain number of texts, the audio alert for text messages stops and only vibrates. I thought it was the phone so Apple exchanged it but I'm still experiencing the same problem with this third phone.

HP Laserjet 4050 toner cartridge issue

I look after a laserjet 4050 printer for a company. They recently started using a new toner cartridge (higher quality) but they have started to have issues with black ink lines down one side of the paper. They have sent back toner cartridges (thinking them to be faulty) but cartridges are fine.
Is this a printer issue or is there an issue with the toner cartridge and the 4050 printer (not compatable)

I think I may have the solution to your problem. I do not think the toner is your problem here. From my experience i would suggest that your printer may need to be cleaned. I had a client who had a similar problem with his printer, what you should try doing is the following:
If toner specks appear on the front or back side of your print jobs, follow the procedure below to clean the paper path.
Using the printer cleaning page
From the printer’s control panel, do the following:
Press MENU until "Print Quality Menu" appears.
Press ITEM until "Create Cleaning Page" appears.
Press SELECT to create the cleaning page.
Follow the instructions on the cleaning page to complete the cleaning process.
NOTE: In order for the cleaning page to work properly, print the page on copier grade paper (not bond or rough paper).
You might need to create a cleaning page more than once. When toner has been cleaned from inside the printer, shiny black spots will appear on the page’s black strip.
To ensure good print quality with certain types of paper, use the cleaning page every time that the print cartridge is replaced.
I am confident that your toner should print clear pages after this.
(Removed items in coflict with Terms of Service (n).)
Message Edited by SandyD on 06-06-2009 12:29 PM

LaserJet software/driver issues. Print and Scan Doctor doesn't work on scanning function of MFP.

Upon using the diagnostic utility HPPSdr. exe, only the select an action "Fix Printing" shows up and not the "Fix Scanning" option. Our printer is the LaserJet 3050 connected via usb running under Windows Vista32 on a HP dv8408us laptop. The scanning driver is HP imaging 4.0.4.0. There have been numerous problems with this scanning software/driver package which have been well illustrated on the HP forums. An update is sorely needed. All that HP customers really expect when we buy a product is that we get the functionality that we paid for and that we get support for the software and hardware for a reasonable length of time, I think that 5-7 years after the final production date of the product, at least, is reasonable. In the case of the 3050, the scanning has never worked right since day 1 because the scans are too light with signatures and time stamps showing up poorly. With the pnp driver installed it it almost impossible to scan in receipts, etc. The communication software Toolbox FX is needed to use the scan button on the machine, and since there are so many problems with this package with respect to system resource usage and connectivity, we can't use it and we don't get the walk up use of the scan button that we paid for originally. As Microsoft has updated the Windows OS, HP has failed to keep pace and we lose functionality of our equipment over time. The diagnostic utilities have supposedly been updated several times and the scanning portion of the MFP still doesn't show. Surely the wide base of installation of this product could justify the expense of some engineering time for an update to the software and drivers. If HP hopes to turn itself around, a commitment needs to be made towards engineering products that really work in the environments that its customers use them, or else HP will merely be regarded as marketing company that is only concerned with selling the next thing without respect to customer retention.

VisionAiry,
Thank you for your response,
     There have been problems with the software and drivers for the LaserJet MFP/AIO machines which have been well illustrated by many users on here for several years. What is shocking is the unwillingness of HP to address these issues at an engineering and design level. This is the level in your organization that these problems need to be addressed at, not at the marketing and customer service level. The software/driver package has never really worked right ever since the 3050 - 3392 series was introduced back in 2006. The scanning drivers in the pnp drivers don't work, and never have, because of frequent communication problems. Someone never bothered to check if a blue ink signature would scan. I and several others have reported on these issues. What I have discoverd, through much trial and error, is that the full software package upon installation with only basic drivers installed using the check boxes in the menu, actually installs differently than the pnp driver. Who would have thought this? So now the machine scans OK.
     My PC really appreciates not having the ToolboxFX installed. ToolBoxFX Error messages and crashes have been well documented on here. This is an application that puts an unnecessary drain on system resources. The only problem is that now the use of the Scan button on the machine is taken away so I don't get the walk up use of the scan button that we paid for in the original design. Why is the scan button function tied to the defective ToolboxFX software?
     As far as printing goes, after carefully deleting the original print drivers, I use the PCL 5 and PCL6 UPD drivers. They work a lot better than the original print drivers ever did. But what about scanning? The scan driver on the 3050 dates all the way back to 7 2007. Scanning is an integral part of the functioning of most offices nowadays, but it is an afterthought at HP. Why would a driver, software or diagnostic package only address half of the capabilities of a machine?
     When I went on the vacation recently, I tried to use my PCL 5 and PCL 6 drivers on my relatives 2009 OfficeJet 7310 and it wouldn't work at all. I had to spend 2 hours with multiple failed attempts to install the full 7310 package on my PC. Installation problems and repeated attempts are a constant theme with HP software. The very term Universal Print Driver is misleading because it won't work on many of the HP products out there. The product listing for the UPD, I only recently discovered on here, with help, because it was so buried on the UPD information page.
     The LaserJet 3050 at $300 from Staples wasn't the most expensive printer out there, but it wasn't the least either. It is actually a pretty nice piece of hardware. I have invested over $1,500 in marked up toner since I've had this machine. HP needs to do better for us.

Problem inserting hp LASERJET 1020 TONER CARTRIDGE

I took the toner cartridge out of my hp laserjet 1020 printer and when I tried to replace it doesn't go back in squarely. Can'r tell if the left side is in to far or if the right side is not in far enough. The printer is turned on. I have removed it before withour incident. Thanks for any advice. BOOBOO2

Hello , Thanks for posting in the HP Forums, and welcome! I understand you are having some issue installing a new toner cartridge in your HP Laserjet 1020 Printer. I'd love to help you with this. Please take a look at this video tutorial for changing the toner on this model - Replacing a Cartridge - HP LaserJet 1020 Printer If you are still unable to install the toner cartridge, I'd recommend taking a look inside the unit with a small flashlight to see if you can see any obstructions. Hope this helps!

New Laserjet 2015 toner LIFE??

i just got a laser 2015 printer
i am able to get only 20-25 good quality prints from this and the toner seems finished, i took it to dealer who confirmed that ink is almost finished.
i asked him to replace the unit, which he, did but the same issue comes again................... there in NO ink in the cartage.
can u ppl plz confirm how much prints this printer can print with supplied cartage?

http://www.hp.com/pageyield/us/en/P2015/index.html lists the standard cartridge at 3000 pages, and 7000 pages for the HP LaserJet Q7553X Black Print Cartridge(53X).
Regards,
Bob Headrick, MS MVP Printing/Imaging
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

HP Laserjet p3015 Major Issue

I recently purchased a brand new Laserjet p3015 printer to run our service dept. work order printing. The problem I am having is that the print test page comes out fine, and so will the first actual print from the printer, as long as it is only one page. From there on out, the printer processes the file and then just freezes up and stops loading. It appears to be getting stuck in the printer queue as not all of the print job loads, (e.g. 156kb/356kb). This is the ONLY printer we have for us, and it is not allowing us to do our job. I have tried the driver from the disk, the PCL 5 and 6 universal drivers, all having the same issue. One PC runs on Vista and another on Windows 7, the Vista machine being mine and the one that I have tried all 3 drivers from. Even the HP diagnostic tool gets hung up stating the print queue is stuck. This is very frustrating to have happen as I have tried everything my fairly confident and educated technical mind can think of, and the fact that our business just spent $500 on a printer we cannot use. If anyone has any sort of help, that would be greatly appreciated. Thanks a lot and have a nice weekend.

Having a similar issue with Windows 7 machines.
PCL XL error
Subsystem: KERNEL
Error: MissingAttribue
Operator: BeginPage
Position: 3
One user started having problems, so I have deleted and readded the printer, which works for awhile, then stops. Deleting and readding the printer seems to make it work again.
Another user cannot print at all ... Deleting and re-adding doesn't make a difference. This user wasn't affected until we updated our print server w/ 38 or so Windows updates. The print server is running Windows Server 2008 R2 Enterprise (64-bit); some of or users are on XP, some on Win7 (all 32-bit); soon all will be on Win7.

HP LaserJet M1132 toner cartridges not delivering full capacity

I have a LaserJet M1132 MFP bought last week. Connection is USB, operating system is Windows 8 - 64bit. Have upgraded to latest firmware. Driver is latest Windows 8 driver. Settings are default (fastres 600).
When using the initial toner cartridge that came with the unit, it delivered only around 250 text (note text and not graphics) pages before it ran out. I know this because I bought three reams of paper when I bought the unit and used half a pack. Coverage was around 50% per page, double sided. I took it out and shook it but this made no difference.
I purchased two new original HP CE285A cartidges at the same time as I bought the printer. I wondered if the original cartridge was a reduced capacity cartridge. So I installed a new cartridge. The toner light came on after printing 935 pages (from the status page). Again, the majority of these were text pages at 50% coverage double sided.
Each cartridge is £75 which gives a per page cost of around 8p/page (not including the cost of the printer) which is outrageous for a laser printer. The packaging estimates around 1,500 pages per cartridge but I clearly didn't get anywhere near this with the first cartridge and am not getting this with the second one either. I have another HP MFP (3500) which delivers around 5 reams before a cartridge runs out.
I am an extremely experienced user with 25 years in printing and imaging and know that estimates assume a certain coverage. I am by no means using a heavy coverage. I am extremely unhappy to say the least. Your help and advice appreciated.
Regards
Tony Harris
This question was solved.
View Solution.

The only thing you can do to try and extend the cartridge life a bit more is enable EconoMode on the print driver. Most likely this was enabled on the devices being tested for the cartridge yield. I'll include the instructions to enable it below. Let me know what happens.
Click on the Start menu.
Click on Devices and Printer.
Right-click on your printer.
Select Printer Preferences.
Click on the Quality tab. It may be labeled as the Paper/Quality tab.
Click the box next to EconoMode to enable it.
Click Apply to save the change.
Click OK to close the window.
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

Hp laserjet 4015 network issue need help

hello and sorry if you all seen this already, i did this post yesterday but its not showing up and my info is not showing i did the post.
ok here's the deal. i have a hp laserjet p4015n printer. right now its connected to a network and every pc thats on the network can see it and print to it etc.
however the current internet package is too expensive and i am planning on doing away with the current provider and goign with a different one. but i have to give them back the equipment.
so i am trying to get everything set up before i do that and i am having problems.
i can get everything else working just fine regardless of what router i use and on both the old slower brother printer is found and can print just fine but the hp printer refuses to be recognized.
i have two routers i have tried this with
a belkin n600
linksys wrt54g
with the linksys router when the printer is connected to it it shows as a device is connected as the light lights up solid but nothing i do can get the printer installed.
i can not ping the route either.
its connected to the router via an ethernet cable
the pcs on the network mostly use win 7 but one is using windows vista but none can install the printer.
i've tried installin gusin ghte host name and ip address
tried using hp's installation software but it just don't find the printer.
this is all driving me nuts and any help would be greatly appreciated.
thanks
ryan

I am sorry, but to get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial printer. You can do this at Printers - LaserJet. Click on New Post.
I hope this helps.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Laserjet 3800N Color Issue

Hi there,
I've got an HP 3800N that the color is not printing properly on. I believe it is a problem with the magenta cartridge as other colors don't seem too bad but the magenta seems light. I've tried printing cleaning pages, replacing the cartridge, reseating the formatter board and changing the color density on the printer itself and ran all the print quality test pages as well. I'm going to try updating the firmware to see if that works but if not I'm thinking that I may have to replace the DC controller board? If so, does anyone have instructions on how to do this? Thanks please let me know if you need more clarification! Thanks.

What type of paper are you using, weight, and content? I'm going assume you are using HP toner cartridges that have not been refilled? If this is the case, you might try a couple of different options. One, you can try to re-calibrate your printer. To do this you can go through the control panel, select Menu, scroll to Configure Device then scroll to Print Quality, scroll to Full Calibrate Now select. This will take a few minutes to reset your printer calibration to optimize print quality. If this does not work, you may want to print the internal Print Quality (PQ) troubleshooting pages. Do this, select Menu, scroll to Diagnostics, select Diagnostics, scroll to PQ Troubleshooting and select. This will print out several different pages. You can use these pages to diagnose if you have an issue with your magenta cartridge. You will need the assistance of hp.com web site to help in troubleshooting these pages. Go to
www.hp.com/go/printquality/clj3800. You will need to calabrate your printer before troubleshooting. This is documented in your User's guide, which ships on the Printer CD that was included with your printer, on page 171 and in Chapter 8. There is also some information on printing issue with color and media on page 170. Follow the instructions on the web page to help resolve your issue.
Although I am an HP employee, I am speaking for myself and not for HP.

HP LaserJet Pro M401n issue with 10.10.2

LaserJet Pro 400 M401n, purchased 10/23/14 and has worked with 10.10.x, connected by USB to MBP (currently with 10.10.2).
LJ M401n has worked with 10.10.x until 3/26/15, when after completing a print job and immediately attempting another print job, I began seeing an error message “79 Service Error Turn Off Turn On” in the printer display.
When again attempting a print job from my MBP, I see the print job being sent to the printer (blinking green light on the printer) and then after a few seconds, the red error light (on the printer) comes on (displaying the error message) and the printer goes into an auto restart (causing the print job to pause). Once the printer restart completes, the print job remains paused; when resumed, the print job does not complete as another “79 Service Error” message occurs.
The LJ M401n remains correctly shown as my Default Printer in Yosemite Sys Pref Printers & Scanners.
From the HP Utility, I can successfully print a Test page as well as a Configuration Report. (Since I can print these test pages, I believe the USB cable, connecting the printer to my MBP, is Ok.)
Looking at other Settings within the HP Utility, everything looks normal. I’ve even compared a newly printed, Configuration Report to one I printed the day I purchased the printer, and all the details are the same, except the Total Impressions (which appears to be correctly keeping count).
I’ve attempted re-installing the HP Drivers 3.0 (from Apple’s web site), which did not achieve any change from what I’ve described above.
Any ideas as to what’s causing the “79 Service Error Turn Off Turn On” error?
(I've posted this same inquiry at HP's Support Forum; so if I get a resolution reply over there, I'll post here to help others.)

** Kappy, I understand I'm posting about an HP Printer, but this Apple Discussions' section is about OS X Yosemite and printers; and as others may have experienced the same issue, I thought it reasonable to post here seeking a resolution. (Please note I did previously mention I'd also posted at HP's Forum.) ...The printer was purchased at Staples; so, I don't expect much help from them. I think posting in this forum, as well as HP's, might achieve quicker results which others might also benefit.
** pmiles, I have done a "Reset the printing system," but issue subsequently remains. I've even deleted the printer from Printers (before reinstalling the HP Drivers 3.0), and added the LJ M401n back afterwards; no success. Each subsequent time I've gotten the 79 Service Error, I deleted the prior print job before initiating a new one. When the printer goes into the 79 Service Error, the printer does an automatic shutdown and restart. After the printer completes the auto-restart, it again shows in my Printers, but just needs to be Resumed.
However, I can provide more details that could provide further insight about this 79 Service Error issue:
I’ve now found that various, doc types (Text rtf, Pages doc, PNG & JPEG pictures) can be printed. PDFs, via Preview, can also be printed as long as the PDF is not generated from a Safari web page. PDFs saved from Safari (regardless of resulting PDF not being a large file - less than 2MB - and even though the LJ M401n has 128MB of memory) are causing the printer to result in the 79 Service Error. As of this writing, I’ve not tested more than a handful of doc types; but, it appears the printer (or possibly, the HP’s printer drivers) is having issue with Safari’s PDF formatting. (I've posted these additional details at HP Forum.)

HP LASERJET P2015 PRINTER ISSUE

I have a P2015 shared printer installed in my office.The pinter works fine for a day but when i come the next day i am unable to print .Then i have to connect to the printer through the network again,only then i am able to print on it.The error shown is unable to print.The OS that i am using is Windows XP and the computer to which the printer is attached to has also windows xp installed on it. We have also got Kaspersky antivirus installed on all the systems in our office.

The product you have seems to be a commercial printer. For the best chance at finding a solution I would suggest posting in the forum for HP Business Support!
You may find the Commercial Laserjet board here.
http://h30499.www3.hp.com/t5/Printers-LaserJet/bd-p/bsc-413
Hope this helps!
Help the community by marking this post as a solution if it solved your issue!.
If my post helped you in any way, please click the blue KUDOS star under my name! It would mean a great deal.

Color LaserJet 3800 Printing Issues

I am in the process of upgrading our desktop computers to Windows 7 Pro (x64). In preparation for this we setup a new print server running Windows Server 2008 R2 and created new print queues for each of the printers on our old Windows 2003 server, installed curent drivers for each, and thought that all would be good.
The issue I am seeing is that our users who are printing to an HP Color LaserJet 3800 are getting letter spacing issues where some letters are crushed together and others are too widely spaced (see example above). I can print the same document to an HP Color LaserJet 3600 everything looks correct.
I have verified that the print server has the HP Color LaserJet 3800 driver that comes with Windows Server 2008 R2 and that the other printer is running the HP Color LaserJet 3600 driver. These are both probably the ones available through Windows Update. Finally, we have tested a solution where the Universal Print driver is intalled locally and that seems to work fine. However, I don't want to have drivers individually installed if I can help it.
Any ideas here?

This seems to be a commercial printer. For the best chance at finding a solution I would suggest posting in the forum for HP Business Support.
You may find the Commercial Laserjet board here.
http://h30499.www3.hp.com/t5/Printers-LaserJet/bd-p/bsc-413
The article for the printer is:
http://h20000.www2.hp.com/bizsupport/TechSupport/Home.jsp?lang=en&cc=us&prodTypeId=18972&prodSeriesI...
This may be the reason why a previous response was not provided or why it was buried..
Hope this helps!
Help the community by marking this post as a solution if it solved your issue!.
If my post helped you in any way, please click the blue KUDOS star under my name! It would mean a great deal.

Hp Laserjet P1102W Wireless issue

I have an HP Laserjet P1102W. My issue is that I just upgraded my router and I have three computers all tied on. No problem with the network. I tried to print wirelessly with the printer and all I get is error messages. So I tried uninstalling and reinstalling the printer. When it comes to the wireless install I connect the usb cable and it connects to the wireless network but when getting the ip address stage it keeps saying printer is connnected to the wireless network but printer cannot communicate with the computer. I tried a straight usb conncection and no problems whatsoever. Can someone tell me what could cause this. Also the operating system is Windows XP. Thanks for any help.

Is the computer it was installed on connected to the wireless network?
The computer being connected by Ethernet to the network is the most likely cause of the issue you are experiencing.
What brand and model is the router?
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

LaserJet 5100 printing issue

I have a LaserJet 5100 - purchased in 2005 - worked great until I just bought a new HP Pavilion computer. It prints normal text fine but having issues printing 11x17 pdf drawings. I have tried loading updated drivers from HP site, called HP and talked to 3 people who didn't help, and talked to the Geek Squad at BestBuy who suggested I buy a new printer! Well, this printer works great so I need help getting it to communicate to the new computer!! Any help is greatly appreciated.

we have scan problim my Hp1005 all in one printer is working but scaner is not warking. erroe no.13

LaserJet M551N Toner Issue

Similar Messages

Maybe you are looking for