Linsky router wrt54g version 6

I have tried to install router and it comes up with give MAC IP and DSP!1&DSP2, what is this and why do I have to have it... I had router before and was very easy set up, this 1 I have been trying to set up for 2 hours now and nothing! Can anyone help please...

Where is it asking you for that information? How are you connecting it to your home network? You can try holding the reset button for 30seconds. Keep the username field blank, and the password is "admin"
I don't work for Cisco. I'm just here to help.

Similar Messages

Wireless Router WRT54G version 7. Connected computer gets disconnected from internet

I have recently installed a Wireless Router WRT54G version 7 for my home office purpose.
My home PC and my laptop are connected to it. Especially on my laptop, I have observed frequently getting disconnected from the internet. I need to power OFF the router and power it ON to get the internet connection restored
Need help to get this problem resolved
Thanks
Rohit

Access set up pageof router .... look for MTU ....change the size from 1500 to 1300 ....click save settings ....
Click on wireless tab ....change the channel to 11 .....click save settings ....
Go to advance wireless settings subtab ....
Beacon interval 75
RTS & Fragmentation threshold 2306...... click save settings ...
Click on status check Ip address & firmware version on the same & let me know ...

Linksys Wireless Router: WRT54G Version: 2

I was just curious, since I have been talking to someone about the Linksys Routers and they were saying that WRT54G Versions 3, 4 & 5, all work successfully. Then when I asked him about Version 2, he said that he THINKS that the router will work.
Can someone please give me an answer: Will the Linksys Wireless Router: WRT54G Version: 2 work with a MacBook Pro?!

I get from 3 to 6 Mbps wireless and wired, which is considerably slower than my other Windows-based desktop and notebook over my 30 Mbps cable connection. My Dell notebook and desktop consistently get 15 Mbps wireless and 22 to 28 Mbps wired. Mac OS is relatively new to me, so I haven't had a chance to read as much I need to about optimizing connection speeds. But, I can either fix it by optimizing it, or perhaps Apple will come out with a firmware update since some people have been complaining about slow connections speeds and dropping connections.
In my work, I have several computers going at the same time, and for typical Web surfing, I see no difference in speed between the 6 Mps on the Mac and the 15 Mpbs on the Dell---it's really limited anyway by the Web site server. I do notice a difference in download times, but even for very large files, the difference is noticeable but not a problem. And, there has never been a problem streaming video or downloading trailers, etc.
Of course, only five years ago, my cable connection was first 128 Kbps (which was high speed then), then they jumped it up 1 Mpbs, then 10 Mbps, and now 30 Mbps---so the 6 Mbps on the Mac still seems pretty fast to me.
Speed will always be slower over the wireless compared to your Ethernet connection, but once you get speeds in excess of 1 Mbps, you only see the difference in download times, surfing is the same.
MacBook, MacBook Pro, Mac Mini PPC Mac OS X (10.4.7) Dell D500 and GX620 with Windows XP Pro

Linksys Wireless Router WRT54G Version 3

I just purchsed and installed a Linksys Wireless Router WRT54G Version 3. It works great in my somewhat small ranch type house. I'm presently just using it so I can wireless access the internet with my Dell notebook computer from any room in my house. My operating system is Windows XP. If I decide to upgrade to Windows Vista in the future will my Linksys Wireless Router WRT54G Version 3 still work ok?
Frank

yes, i think it will work... just make sure that the firmware of your router is up-to-date with the latest releases from linksys... you can check it out at http://www.linksys.com/downloads and just choose the model no. and version of your router... also, try to check the knowledge base website at http://www.linksys.com/kb ... i hope this helps... good luck buddy
♥ Registered TradeMark Since 1987 ♥

Router wrt54g version 6 without firmware

Hi. I think i fried my router. I eras the firmware to try and convert the router into a repeater. I was able to erased everything but now it does not work at all. The PC does not recognize the ports. I tried opening the router and reset the flash rom to be able to enter the failproof mode,, but id did not work either. Please help!!!! How can i get my router back to work...

How did you erase the router's firmware ? What steps you have taken to get the Firmware back...

NAT issue - WRT54G Version 1.1 with Vista Home Premium

Router = WRT54G Version 1.1
I am trying to figure out the cause of my problems, this router or Vista?
I have 2 PC’s (just want to use my Vista 1) connected to the same router that is connected to a cable modem – the Windows XP machine has no problems bar its age and spec. I have a brand new PC with Vista Home Premium installed on it, now it is this new PC that I am having NAT problems with and port blocking.
I have installed Windows Live Messenger and when setting it up I went into Tools/Options/Connections and I get an error message:- "You are connected to the internet through a UPnP port restricted NAT. The Windows Firewall is enabled. (User)"
I have no option to run the trouble shooter (greyed out)…….
If I turn off Windows Vista Firewall I get:- "You are connected to the internet through a UPnP port restricted NAT. (User)”
Since this I have installed Media server software and have to reset the port it uses every time as it is always stating that it is blocked.
I have downloaded OpenOffice via a torrent client which also stated that I had NAT problems.
I have no NAT issues at all on my older XP PC and as a result I believe it is safe to rule out my router and modem……..I have only disabled Windows Firewall and this had made no difference, but I have not tried uninstalling it (no idea if that would make a difference)
Oh, I do not have UPnP enabled (router setting) – does this matter (I have tried turning it on but made no difference to this issue so I turned it off again)?
Message Edited by jomuir on 08-23-2007 02:50 AM

user11241256 wrote:
Documentation states that Oracle is supported on Vista business and Ultra. unfortuntatly Ihave Home Premium 64 and was curious if anyone had experience imstalling on this OS. I did attempt to install the 11g and I got one warning below that I could not find in the documentation for errors. You have answered your query yourself.
You might be able to get the things running on an unsupported combination but there is no guarantee about the stability.

Linksys WRT54GS Version 6 router help

Hi all! I have a Linksys WRT54GS Version 6 router with Firmware Version: v1.50.6 and I was wondering if anyone could help me find a free log viewer, since the log viewer that comes with the router just gives the last few sites outgoing and incoming, and it doesn't time it either. Anything that will work with my router that will record all day info as well as put the time? I'd also like it (if possible) if it could identify which websites those IP's belong to; sometimes I will put an IP in the address bar and nothing happens or I get an error.
Also, I can't seem to be able to telnet into my router. I put the right IP 192.168.1.1 8080 which is the port that shows under Administration/Management "management port:" 8080. When I telnet (I'm using vista and I installed the telnet client and server) it says connecting and then just sits there for a long time and then asks me to push any key and says connection timed out. I also tried with port 80 and 23, nothing.
Thanks!

*BUMP*
I gathered from what I read on the 'net that this particular router pretty much sucks in terms of putting 3rd party firmware, of telnetting into it, etc. So, is it basically true that there is no way to telnet into this? Also, no one knows of any monitoring or log viewer that works with this version?? Please?
Message Edited by PsychGirl on 04-16-2009 09:35 AM

HI I HAVE WRT54G WIRELESS ROUTER WITH VERSION 7. NOW I W...

HI
I HAVE WRT54G WIRELESS ROUTER WITH VERSION 7.
NOW I WANTED TO UPGRADE THE FIRMWARE.
I CHCAKED OUT THE SITE I COULD'NT FIND THE DRIVERS FOR THE VER 7
EVERYTHING ELSE OTHER THAN VER 7 IS PRESENT ON SITE I WANTED TO CHEAK OUT WHEATHER THE VER 7 FIRMWARE ARE AVALIABLE OR NOT PLEASE HELP ME TO DO SO
THANKS
PRAVIN

hi helm
Thanks a lot for your suggestion i got the required farmware
thanks
prav

WRT54G Version 7.0 - mother of all problems: Why are the DNS-fields in the status blank?

Ever since the purchase of my WRT54G Version 7.0 WLAN Router two years, I kept getting IP- and DNS-problems, but recently, I cannot access websites anymore at all. As I've already replaced the thing with another router months ago and just now, started to set it up at a friend's place while getting the same problems (with every single computer in the network), I'm sure that the problem lies at the router. All Windows computers report in uni sono that there may be a DNS problem. Firmware is up to date to 7.00.4. Ironically, LinkSys doesn't seem to feature drivers downloads to Version 7.0 anymore, though.
I've got the DHCP-server function activated, left the IP-address to 192.168.1.1 and the DNS-addresses 1, 2 and 3 to the usual 0.0.0.0. I didn't change the default WINS 0.0.0.0, either.
Interestingly, however, when switching to the status tab, the DNS1, DNS2 and DNS3-fields remain completely blank. Therefore, I assume that the router doesn't run any DNS with 0.0.0.0-setup.
Now, how can I make this expensive thing take up the DNS-tasks so that all those computers can access websites again?

Who is your Internet Service Provider ?
What is the IP Address you are getting on the status page of the router ?
What is the IP Address you are getting when connected to the modem directly ?
You can Download the firmware for WRT54G V7 (7.00.8)
Try this :
Press and hold the reset button for 60 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
If your Internet Service Providor is Cable follow this link
If your Internet Service Providor is DSL follow this link

WRT54G version 3.0 Streaming Video Issue

I have a WRT54G v3.0 wireless router that constantly drops connection when I try to stream video from the internet. If I eliminate the router and connect my laptop or desktop directly to my cable modem streaming video works perfect. Once I put the wireless router back into play and try to stream video I lose connection to the router. Normal internet use (e-mail, sports sites, etc.) work fine but as soon as I go to a site like youtube or espn and try to stream video the wireless connection drops. I have read numerous message boards that talk about firmware upgrades that will fix the problem but all of the message boards talk about WRT54G versions other than mine. Can anyone out there tell me why my WRT54G v3.0 router constantly drops connection when streaming video as well as tell me how to fix it?
By the way I currently have firmware version 3.03.6 (Jan 6, 2005) installed

I think the latest for v3 is firmware 4.21.1. Check out your model and version on http://www.linksys.com/download
The box said windows xp or better... So I installed Linux!

WRT54G Version 3.1 Connection Issues - Help Please

Good Morning,
We have a WRT54G Version 3.1. Our existing network is wired and functions fine, I am adding the WRT54G for a few wireless clients.
During testing I have connected the wireless to my computer via CAT5 cable to port 1. I have connected another CAT5 cable to the internet port of the router from a known good wall jack.
When I first open the default address 192.168.1.1 and enter the password, all seems well. Due to having servers that hand out IP addresses, I disable the routers DHCP capability.
I enter the following information for example:
Local IP: 81.0.0.90
Gateway: 81.0.0.1
Subnet: 255.255.255.0
DHCP disabled
etc.
After changing the the local IP and receiving a confirmation that my changes were saved and I will be going back to the previous page, the page won't display with the address changed to 81.0.0.90 and it is blank.
I release my IP address through cmd, clear my dns cache and reboot the computer. After restart, I am presented with the stock MS address of 169.254.X.X.
I cannot connect to the local IP I established at 81.0.0.90 and nothing appears to work. The only thing I can do is reset the router and start from scratch...again.
Any ideas on what keeps happening and how it can be resolved once and for all?
Thanks in advance
Message Edited by T1Tech on 10-23-200603:49 PM

even if you have two DHCP enabled on both routers in your network, you will not get an IP adress conflict (exception of course if you're cascading two wireless routers).
a LAN port (ethernet router) to WAN port (wireless router) connection can be established allowing you to have both DHCP server enabled on your routers.
by doing the LAN to WAN connection, you will have two networks in a network.. both network won't meet cuz they will have different IP adress... router 1: could be 81.0.0.90, then router 2 could be 81.0.0.91.
if you want your two routers to meet and be in the network together, you just need to follow QUAK's suggestion to assign a static IP adress on your PC. or better yet, you can just connect the router you're disabling the DHCP server with to it's LAN port from a LAN port as well of your DHCP server (router 1). this is a LAN to LAN connection... by doing that, you will be able to open up the interface of your router 2(DHCP disabled) since your PC connected to it will get an IP adress...
"a helping hand in a community makes the world a universe"

Airport Extreme, Linksys Router WRT54G: Internet is Impossibly Slow

I have a problem regarding wireless internet activity on my Powerbook G4. In my house, I have a Linksys Router (WRT54G) that has worked fine for other laptops (including an iBook running Airport Extreme, a Powerbook G4 running Airport, and an iMac running Airport) for many years. When I got a refurbished Powerbook G4 1.67 GHz with Airport Extreme, I found that while Airport could be configured to recognize the wireless network (with a WEP 40/128-bit encrypted key), it barely works on the computer. The signal strength is strong (the laptop is hooked up right above the Linksys router), but the Internet barely works at all. Surfing to webpages takes 10-20-30 sec to work, and often the connection seems to drop off all together. Something is clearly wrong because despite the fact that this is my fastest computer with the fastest wireless capability, it runs at a slower pace than any computer I have ever used on the web.
I was wondering if anyone has had similar problems with getting Wireless Extreme on Powerbook G4s to work with this particular (and older) model of Linksys wireless browser (WRT54G). Some Internet sleuthing led me to believe that perhaps the router firmware needs to be updated or something like that, but I haven't really found any definitive answers. If there is anything wrong on the laptop-OS-side, I have no idea. I would appreciate any pointers that you can provide!
Thank you to all,
Matthew
Computer:
Powerbook G4
1.67 GHz
1 GB DDR SDRAM
OS 10.4.8
Wireless Router:
Linksys
Model: WRT54G
Powerbook G4 Mac OS X (10.4.8) 1.67GHz, 1GB DDR SDRAM

Hi all,
Thank you for your help. Unfortunately, my problems persist.
I was able to reset my router and to configure it again on the web-based router configuration.
As per your suggestion, I tried switching the Wireless Network Mode to "G-only." Not only did this kick off my older computers on the network (an old iMac and an older Powerbook G4, both with normal airport), but it did not fix the speed problems on the new Powerbook G4/with Airport Extreme. I am back on the mixed setting now in order to get most of the computers on the network back to their old working states...
I also tried disabling my WEP encrypted key but found that this did not speed anything up at all.
I have upgraded my firmware from its previous version, v 1.41.2 (very old!), to the latest from the Linksys website: v 4.30.5. This has not helped at all either.
Is it possible that there is any setting on the Powerbook/Airport Extreme itself that is causing these problems?
Thank you all again for your help,
Matthew
Powerbook G4 Titanium Mac OS X (10.4.7) 1gHz, 512mb RAM

Wrt54g version 2.2

I have an older router the wrt54g version 2.2. And I want to use this for testing. Now I try to configure the router. But the router won't get any internet access. I tried to configure by 192.168.1.1 and the cd. And no matter what I do I won't have any internet connectivity. I tried to do a firmware update but this was failed. So also that won't work. I'm not sure what I can do now, can you help me further
Message Edited by patricia8609 on 05-13-2009 09:15 AM

Reset your router and then re-configure it...
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
Also make sure that your computer is set to obtain IP automatically, disable any firewalls, security softwares on the computer before trying to access the setup page...
To configure your Linksys router
Follow this link if your Internet Service Providor is Cable
Follow this link if your Internet Service Providor is DSL

WRT54G version 2 firmware issued

Good Evening all;
I mistakenly downloaded and installed version 4 firmware when i should have installed version 2. My system (windows ver. 7) no longer sees the wireless router (WRT54G). I no longer have the install CD and the version 2 firware does not seem to be available on the website. Is my router now dead in the water?

it depends. is the power light on your router blinking? can you still access the router's "setup" page? did you reset your router after doing the firmware upgrade?

WRT54G Version 2 Firmware Reset?

Hello,
I have a Linksys WRT54G Version 2 that I installed the V.6. firmware on, and now I cannot connect through the router, or even reach the admin panel. Is there a way to reset Version 2 like Version 5?
Thanks!Message Edited by Kadratis on 11-25-200612:49 PM

you can try to reset this router for 1 min. and Then try to upgrade the router firmware with v2 firmware. Go to site: ftp://ftp.linksys.com/pub/network and search for tftp.exe and download tftp.exe and use this tool to upgrade the firmware file to this router. May this help you!
Make sure you upload only v2 files.

Linsky router wrt54g version 6

Similar Messages

Maybe you are looking for